mediatek: filogic: add support for ZBT-Z8803BE
Specifications:
SoC: MediaTek MT7988A (4 cores)
RAM: 1024MiB
Flash: Winbond SPI-NAND 128 MiB
Network: 1 WAN (2.5G), 3 LAN (1G), 1 SFP+ (10G)
2 SIM slots
Buttons: Reset, WPS
Power: DC 12V 3A (Recommend 19V to avoid voltage drop)
WiFi: MT7996 2.4Ghz, 5.8Ghz and 6Ghz (BE19000)
- 2.4Ghz and 5.8Ghz share same dual band antenna (4)
- 6Ghz uses dedicated 6G antenna (4)
Misc: 1 USB2.0 port, UART header
Installation:
A. Through U-Boot menu:
- Prepare your connecting computer to use a static IP in
network 192.168.1.0/24
- Power down the router and hold in the Reset button.
- While holding in the button power up the router again.
- Hold the button in for 10 seconds and then release.
- Use your browser to go to 192.168.1.1
- If you see a GUI allowing for flashing firmware then
you got the right model.
- Upload the sysupgrade file.
Note 1: Recovery GUI can be used to recover from an incorrect
firmware flash.
Note 2: There is a GPIO watchdog that expires after 2 minutes
so flashing sysupgrade via U-boot needs to be done
quickly within that timer.
B. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled
(modified by the seller), you can easily upgrade
by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware,
then flash the firmware
MAC Addresses:
LAN(printed MAC) : F8:5E:3C:xx:xx:xx (Factory, 0xffff4)
WAN : F8:5E:3C:xx:xx:xx (Factory, 0xffffa)
SFP+ : F8:5E:3C:xx:xx:xx (Factory, 0xfffee)
2.4GHz : F8:5E:3C:xx:xx:xx (Factory, 0x4)
5GHz : F8:5E:3C:xx:xx:xx (Factory, 0x4) + 0x10
6Ghz : F8:5E:3C:xx:xx:xx (Factory, 0x4) + 0x20
Signed-off-by: Tuan Phan <pttuan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23053
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Tuan Phan
Hauke Mehrtens
parent
b2795a7908
commit
2808857215
561
target/linux/mediatek/dts/mt7988a-zbtlink-zbt-z8803be.dts
Normal file
561
target/linux/mediatek/dts/mt7988a-zbtlink-zbt-z8803be.dts
Normal file
@ -0,0 +1,561 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
|
||||
/dts-v1/;
|
||||
#include "mt7988a.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include <dt-bindings/pinctrl/mt65xx.h>
|
||||
#include <dt-bindings/regulator/richtek,rt5190a-regulator.h>
|
||||
|
||||
/ {
|
||||
model = "Zbtlink Z8803BE";
|
||||
compatible = "zbtlink,zbt-z8803be", "mediatek,mt7988a";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_blue;
|
||||
led-failsafe = &led_red;
|
||||
led-running = &led_blue;
|
||||
led-upgrade = &led_blue;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n1 \
|
||||
earlycon=uart8250,mmio32,0x11000000 \
|
||||
pci=pcie_bus_perf";
|
||||
};
|
||||
|
||||
memory@40000000 {
|
||||
reg = <0x0 0x40000000 0x0 0x40000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&pio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_red: red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 62 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
green {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
gpios = <&pio 58 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led_blue: blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
gpios = <&pio 60 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led-5g1 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_MOBILE;
|
||||
function-enumerator = <1>;
|
||||
gpios = <&pio 61 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led-5g2 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_MOBILE;
|
||||
function-enumerator = <2>;
|
||||
gpios = <&pio 53 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
/*
|
||||
* Enable power to the primary modem (modem0) by default.
|
||||
* The secondary slot (modem1) remains powered off until
|
||||
* userspace explicitly enables it when populated.
|
||||
*/
|
||||
modem0 {
|
||||
gpio-export,name = "5g1";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pio 17 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
modem1 {
|
||||
gpio-export,name = "5g2";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&pio 52 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
sim {
|
||||
gpio-export,name = "sim";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pio 59 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
sfp: sfp@0 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c2>;
|
||||
mod-def0-gpios = <&pio 82 GPIO_ACTIVE_LOW>;
|
||||
los-gpios = <&pio 81 GPIO_ACTIVE_HIGH>;
|
||||
tx-disable-gpios = <&pio 36 GPIO_ACTIVE_HIGH>;
|
||||
maximum-power-milliwatt = <3000>;
|
||||
};
|
||||
|
||||
fan: pwm-fan {
|
||||
compatible = "pwm-fan";
|
||||
#cooling-cells = <2>;
|
||||
cooling-levels = <0 80 112 144 176 216 255>;
|
||||
pwms = <&pwm 0 10000 0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog-gpio {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&pio 18 GPIO_ACTIVE_HIGH>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <60000>;
|
||||
always-running;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&cpu0 {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cpu1 {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cpu2 {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cpu3 {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cci {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cpu_thermal {
|
||||
/delete-node/cooling-maps;
|
||||
/delete-node/trips;
|
||||
|
||||
trips {
|
||||
cpu_trip_crit: crit {
|
||||
temperature = <100000>;
|
||||
hysteresis = <2000>;
|
||||
type = "critical";
|
||||
};
|
||||
|
||||
cpu_trip_active_high: active-high {
|
||||
temperature = <60000>;
|
||||
hysteresis = <2000>;
|
||||
type = "active";
|
||||
};
|
||||
|
||||
cpu_trip_active_low: active-low {
|
||||
temperature = <45000>;
|
||||
hysteresis = <2000>;
|
||||
type = "active";
|
||||
};
|
||||
|
||||
cpu_trip_active_silent: active-silent {
|
||||
temperature = <38000>;
|
||||
hysteresis = <2000>;
|
||||
type = "active";
|
||||
};
|
||||
};
|
||||
|
||||
cooling-maps {
|
||||
cpu-active-high {
|
||||
/* active: set fan to cooling level 3 */
|
||||
cooling-device = <&fan 3 3>;
|
||||
trip = <&cpu_trip_active_high>;
|
||||
};
|
||||
|
||||
cpu-active-low {
|
||||
/* active: set fan to cooling level 1 */
|
||||
cooling-device = <&fan 1 1>;
|
||||
trip = <&cpu_trip_active_low>;
|
||||
};
|
||||
|
||||
cpu-active-silent {
|
||||
/* active: set fan to cooling level 0 */
|
||||
cooling-device = <&fan 0 0>;
|
||||
trip = <&cpu_trip_active_silent>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
mdio0_pins: mdio0-pins {
|
||||
mux {
|
||||
function = "eth";
|
||||
groups = "mdc_mdio0";
|
||||
};
|
||||
|
||||
conf {
|
||||
groups = "mdc_mdio0";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
};
|
||||
};
|
||||
|
||||
gbe0_led0_pins: gbe0-led0-pins {
|
||||
mux {
|
||||
function = "led";
|
||||
groups = "gbe0_led0";
|
||||
};
|
||||
};
|
||||
|
||||
gbe2_led0_pins: gbe2-led0-pins {
|
||||
mux {
|
||||
function = "led";
|
||||
groups = "gbe2_led0";
|
||||
};
|
||||
};
|
||||
|
||||
gbe3_led0_pins: gbe3-led0-pins {
|
||||
mux {
|
||||
function = "led";
|
||||
groups = "gbe3_led0";
|
||||
};
|
||||
};
|
||||
|
||||
i2c0_pins: i2c0-g0-pins {
|
||||
mux {
|
||||
function = "i2c";
|
||||
groups = "i2c0_1";
|
||||
};
|
||||
};
|
||||
|
||||
i2c2_0_pins: i2c2-g0-pins {
|
||||
mux {
|
||||
function = "i2c";
|
||||
groups = "i2c2_0";
|
||||
};
|
||||
};
|
||||
|
||||
i2p5gbe_led0_pins: 2p5gbe-led0-pins {
|
||||
mux {
|
||||
function = "led";
|
||||
groups = "2p5gbe_led0";
|
||||
};
|
||||
};
|
||||
|
||||
spi0_flash_pins: spi0-flash-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c0_pins>;
|
||||
status = "okay";
|
||||
|
||||
rt5190a@64 {
|
||||
compatible = "richtek,rt5190a";
|
||||
reg = <0x64>;
|
||||
vin2-supply = <&rt5190_buck1>;
|
||||
vin3-supply = <&rt5190_buck1>;
|
||||
vin4-supply = <&rt5190_buck1>;
|
||||
|
||||
regulators {
|
||||
rt5190_buck1: buck1 {
|
||||
regulator-name = "rt5190a-buck1";
|
||||
regulator-min-microvolt = <5090000>;
|
||||
regulator-max-microvolt = <5090000>;
|
||||
regulator-allowed-modes =
|
||||
<RT5190A_OPMODE_AUTO RT5190A_OPMODE_FPWM>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
buck2 {
|
||||
regulator-name = "vcore";
|
||||
regulator-min-microvolt = <600000>;
|
||||
regulator-max-microvolt = <1400000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
rt5190_buck3: buck3 {
|
||||
regulator-name = "vproc";
|
||||
regulator-min-microvolt = <600000>;
|
||||
regulator-max-microvolt = <1400000>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
buck4 {
|
||||
regulator-name = "rt5190a-buck4";
|
||||
regulator-min-microvolt = <850000>;
|
||||
regulator-max-microvolt = <850000>;
|
||||
regulator-allowed-modes =
|
||||
<RT5190A_OPMODE_AUTO RT5190A_OPMODE_FPWM>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
ldo {
|
||||
regulator-name = "rt5190a-ldo";
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c2_0_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: spi_nand@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi_nand {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x00000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x400000>;
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
mt7996_eeprom: eeprom@0 {
|
||||
reg = <0x0 0x1e00>;
|
||||
};
|
||||
|
||||
gmac0_mac: macaddr@ffff4 {
|
||||
reg = <0xffff4 0x6>;
|
||||
};
|
||||
|
||||
gmac1_mac: macaddr@ffffa {
|
||||
reg = <0xffffa 0x6>;
|
||||
};
|
||||
|
||||
gmac2_mac: macaddr@fffee {
|
||||
reg = <0xfffee 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "FIP";
|
||||
reg = <0x580000 0x200000>;
|
||||
};
|
||||
|
||||
partition@780000 {
|
||||
label = "ubi";
|
||||
reg = <0x780000 0x7080000>;
|
||||
compatible = "linux,ubi";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
pcie@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
|
||||
mt7996@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
nvmem-cells = <&mt7996_eeprom>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie3 {
|
||||
/*
|
||||
* Since the PCIe probe order is PCIe3 -> PCIe0 -> PCIe1 and there is
|
||||
* only one reset GPIO available, it must be connected to the first
|
||||
* device in the probe sequence (PCIe3).
|
||||
*/
|
||||
wifi-reset-gpios = <&pio 7 GPIO_ACTIVE_LOW>;
|
||||
wifi-reset-msleep = <100>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&gmac0_mac>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
phy-mode = "internal";
|
||||
phy-connection-type = "internal";
|
||||
phy = <&int_2p5g_phy>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&gmac1_mac>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
sfp = <&sfp>;
|
||||
managed = "in-band-status";
|
||||
phy-mode = "10gbase-r";
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&gmac2_mac>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&int_2p5g_phy {
|
||||
pinctrl-names = "i2p5gbe-led";
|
||||
pinctrl-0 = <&i2p5gbe_led0_pins>;
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gsw_phy0 {
|
||||
pinctrl-names = "gbe-led";
|
||||
pinctrl-0 = <&gbe0_led0_pins>;
|
||||
};
|
||||
|
||||
&gsw_phy0_led0 {
|
||||
function = LED_FUNCTION_LAN;
|
||||
color = <LED_COLOR_ID_ORANGE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gsw_port0 {
|
||||
label = "lan0";
|
||||
};
|
||||
|
||||
&gsw_phy1 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&gsw_port1 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&gsw_phy2 {
|
||||
pinctrl-names = "gbe-led";
|
||||
pinctrl-0 = <&gbe2_led0_pins>;
|
||||
};
|
||||
|
||||
&gsw_phy2_led0 {
|
||||
function = LED_FUNCTION_LAN;
|
||||
color = <LED_COLOR_ID_ORANGE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gsw_port2 {
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
&gsw_phy3 {
|
||||
pinctrl-names = "gbe-led";
|
||||
pinctrl-0 = <&gbe3_led0_pins>;
|
||||
};
|
||||
|
||||
&gsw_phy3_led0 {
|
||||
function = LED_FUNCTION_LAN;
|
||||
color = <LED_COLOR_ID_ORANGE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gsw_port3 {
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
&ssusb0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssusb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tphy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&xsphy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&serial0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwm {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
@ -342,7 +342,8 @@ xiaomi,redmi-router-ax6000-ubootmod)
|
||||
ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan"
|
||||
;;
|
||||
zbtlink,zbt-z8103ax|\
|
||||
zbtlink,zbt-z8103ax-c)
|
||||
zbtlink,zbt-z8103ax-c|\
|
||||
zbtlink,zbt-z8803be)
|
||||
ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx"
|
||||
;;
|
||||
zbtlink,zbt-z8106ax-s|\
|
||||
|
||||
@ -23,6 +23,10 @@ mediatek_setup_interfaces()
|
||||
zbtlink,zbt-z8103ax-c)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1
|
||||
;;
|
||||
zbtlink,zbt-z8803be)
|
||||
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1
|
||||
ucidef_set_interface "wan_sfp" device "eth2" protocol "none"
|
||||
;;
|
||||
acelink,ew-7886cax|\
|
||||
tplink,eap683-lr)
|
||||
ucidef_set_interface_lan "eth0" "dhcp"
|
||||
|
||||
@ -292,7 +292,8 @@ platform_do_upgrade() {
|
||||
nand_do_flash_file "$1" || nand_do_upgrade_failed
|
||||
nand_do_upgrade_success
|
||||
;;
|
||||
tplink,fr365-v1)
|
||||
tplink,fr365-v1|\
|
||||
zbtlink,zbt-z8803be)
|
||||
CI_UBIPART="ubi"
|
||||
CI_KERNPART="kernel"
|
||||
CI_ROOTPART="rootfs"
|
||||
|
||||
@ -3679,6 +3679,23 @@ define Device/zbtlink_zbt-z8106ax-t
|
||||
endef
|
||||
TARGET_DEVICES += zbtlink_zbt-z8106ax-t
|
||||
|
||||
define Device/zbtlink_zbt-z8803be
|
||||
DEVICE_VENDOR := Zbtlink
|
||||
DEVICE_MODEL := ZBT-Z8803BE
|
||||
DEVICE_DTS := mt7988a-zbtlink-zbt-z8803be
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-sfp kmod-hwmon-pwmfan kmod-usb3 kmod-mt7996-firmware mt7988-2p5g-phy-firmware mt7988-wo-firmware
|
||||
DEVICE_DTC_FLAGS := --pad 4096
|
||||
SUPPORTED_DEVICES += zbtlink,zbt-z8803be,mt7988a-nand
|
||||
KERNEL := kernel-bin | gzip | \
|
||||
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
||||
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += zbtlink_zbt-z8803be
|
||||
|
||||
define Device/zyxel_ex5601-t0-stock
|
||||
DEVICE_VENDOR := Zyxel
|
||||
DEVICE_MODEL := EX5601-T0
|
||||
|
||||
Loading…
Reference in New Issue
Block a user