diff --git a/target/linux/mediatek/patches-6.18/737-net-dsa-add-Airoha-AN8855.patch b/target/linux/mediatek/patches-6.18/737-net-dsa-add-Airoha-AN8855.patch index affbd025e4..c86f2423ac 100644 --- a/target/linux/mediatek/patches-6.18/737-net-dsa-add-Airoha-AN8855.patch +++ b/target/linux/mediatek/patches-6.18/737-net-dsa-add-Airoha-AN8855.patch @@ -37,101 +37,7 @@ Saddly for that part we have absolutely NO documentation currently. There is this special thing where PHY needs to be calibrated with values from the switch efuse. (the thing have a whole cpu timer and MCU) -Changes v11: -- Address reviews from Christophe (spell mistake + dev_err_probe) -- Fix kconfig dependency for MFD driver (depends on MDIO_DEVICE instead of MDIO) - (indirectly fix link error for mdio APIs) -- Fix copy-paste error for MFD driver of_table -- Fix compilation error for PHY (move NVMEM to .config) -- Drop unneeded NVMEM node from MDIO example schema (from Andrew) -- Adapt MFD example schema to MDIO reg property restrictions -Changes v10: -- Entire rework to MFD + split to MDIO, EFUSE, SWITCH separate drivers -- Drop EEE OPs (while Russell finish RFC for EEE changes) -- Use new pcs_inpand OPs -- Drop AN restart function and move to pcs_config -- Enable assisted_learning and disable CPU learn (preparation for fdb_isolation) -- Move EFUSE read in Internal PHY driver to .config to handle EPROBE_DEFER - (needed now that NVMEM driver is register externally instead of internally to switch - node) -Changes v9: -- Error out on using 5G speed as currently not supported -- Add missing MAC_2500FD in phylink mac_capabilities -- Add comment and improve if condition for an8855_phylink_mac_config -Changes v8: -- Add port Fast Age support -- Add support for Port Isolation -- Use correct register for Learning Disable -- Add support for Ageing Time OP -- Set default PVID to 0 by default -- Add mdb OPs -- Add port change MTU -- Fix support for Upper VLAN -Changes v7: -- Fix devm_dsa_register_switch wrong export symbol -Changes v6: -- Drop standard MIB and handle with ethtool OPs (as requested by Jakub) -- Cosmetic: use bool instead of 0 or 1 -Changes v5: -- Add devm_dsa_register_switch() patch -- Add Reviewed-by tag for DT patch -Changes v4: -- Set regmap readable_table static (mute compilation warning) -- Add support for port_bridge flags (LEARNING, FLOOD) -- Reset fdb struct in fdb_dump -- Drop support_asym_pause in port_enable -- Add define for get_phy_flags -- Fix bug for port not inititially part of a bridge - (in an8855_setup the port matrix was always cleared but - the CPU port was never initially added) -- Disable learning and flood for user port by default -- Set CPU port to flood and learning by default -- Correctly AND force duplex and flow control in an8855_phylink_mac_link_up -- Drop RGMII from pcs_config -- Check ret in "Disable AN if not in autoneg" -- Use devm_mutex_init -- Fix typo for AN8855_PORT_CHECK_MODE -- Better define AN8855_STP_LISTENING = AN8855_STP_BLOCKING -- Fix typo in AN8855_PHY_EN_DOWN_SHIFT -- Use paged helper for PHY -- Skip calibration in config_init if priv not defined -Changes v3: -- Out of RFC -- Switch PHY code to select_page API -- Better describe masks and bits in PHY driver for ADC register -- Drop raw values and use define for mii read/write -- Switch to absolute PHY address -- Replace raw values with mask and bits for pcs_config -- Fix typo for ext-surge property name -- Drop support for relocating Switch base PHY address on the bus -Changes v2: -- Drop mutex guard patch -- Drop guard usage in DSA driver -- Use __mdiobus_write/read -- Check return condition and return errors for mii read/write -- Fix wrong logic for EEE -- Fix link_down (don't force link down with autoneg) -- Fix forcing speed on sgmii autoneg -- Better document link speed for sgmii reg -- Use standard define for sgmii reg -- Imlement nvmem support to expose switch EFUSE -- Rework PHY calibration with the use of NVMEM producer/consumer -- Update DT with new NVMEM property -- Move aneg validation for 2500-basex in pcs_config -- Move r50Ohm table and function to PHY driver - -Christian Marangi (9): - dt-bindings: nvmem: Document support for Airoha AN8855 Switch EFUSE - dt-bindings: net: Document support for Airoha AN8855 Switch Virtual - MDIO - dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch - dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC - mfd: an8855: Add support for Airoha AN8855 Switch MFD - net: mdio: Add Airoha AN8855 Switch MDIO Passtrough - nvmem: an8855: Add support for Airoha AN8855 Switch EFUSE - net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver - net: phy: Add Airoha AN8855 Internal Switch Gigabit PHY - +--- .../bindings/mfd/airoha,an8855-mfd.yaml | 178 ++ .../bindings/net/airoha,an8855-mdio.yaml | 56 + .../net/dsa/airoha,an8855-switch.yaml | 105 + @@ -274,3 +180,14 @@ Christian Marangi (9): obj-$(CONFIG_AIR_EN8811H_PHY) += air_en8811h.o obj-$(CONFIG_AMD_PHY) += amd.o obj-$(CONFIG_AMCC_QT2025_PHY) += qt2025.o +--- a/drivers/nvmem/Kconfig ++++ b/drivers/nvmem/Kconfig +@@ -31,7 +31,7 @@ source "drivers/nvmem/layouts/Kconfig" + + config NVMEM_AN8855_EFUSE + tristate "Airoha AN8855 eFuse support" +- depends on COMPILE_TEST ++ depends on MFD_AIROHA_AN8855 || COMPILE_TEST + help + Say y here to enable support for reading eFuses on Airoha AN8855 + Switch. These are e.g. used to store factory programmed