mediatek/filogic: add support for COMFAST CF-XR186
The COMFAST CF-XR186 is a WiFi repeater. The original OEM firmware is a fork of OpenWrt 21.02. To replace the OEM firmware with OpenWrt, flash the sysupgrade image through the firmware upgrade option via the OEM firmware's web UI. The OEM firmware upgrade page does not provide an option to perform a factory reset, so after the flash completes and the device reboots, perform a reset by holding in the WPS/Reset button until the WiFi LED flashes red. The led-boot, led-failsafe, led-upgrade, and led-running aliases all point at the red WLAN GPIO LED. The green and blue WLAN GPIO LEDs are used to indicate activity on the 2.4GHz and 5GHz radios. 01_leds assigns netdev triggers for those LEDs to phy0-ap0 and phy1-ap0 respectively; if neither AP interface exists (e.g. station-only repeater setups), both LEDs stay dark even when WiFi traffic is flowing. Specifications: - SoC: MediaTek MT7981B - RAM: 256MB - Flash: SPI NAND - WiFi: 2.4GHz + 5GHz (AX3000, 4x 3dBi antennas) - Ethernet: 1x 10/100/1000M - LEDs: power (not controllable), blue Ethernet, blue/green/red WiFi - Button: WPS/Reset - Power: 100-240V AC (wall plug) - UART: 115200 8N1 MAC Addresses: - LAN : 40:A5:EF:xx:xx:2D (Factory, 0xe000) - 2.4GHz: 40:A5:EF:xx:xx:2F (Factory, 0x0004) - 5GHz : 40:A5:EF:xx:xx:30 (Factory, 0x8000) Signed-off-by: David Berdik <dgberdik@gmail.com> Link: https://github.com/openwrt/openwrt/pull/22471 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
David Berdik
Hauke Mehrtens
parent
1eabd76d28
commit
a07f62f65a
225
target/linux/mediatek/dts/mt7981b-comfast-cf-xr186.dts
Normal file
225
target/linux/mediatek/dts/mt7981b-comfast-cf-xr186.dts
Normal file
@ -0,0 +1,225 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
#include "mt7981b.dtsi"
|
||||
|
||||
/ {
|
||||
model = "COMFAST CF-XR186";
|
||||
compatible = "comfast,cf-xr186", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
label-mac-device = &gmac1;
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_wifi_red;
|
||||
led-failsafe = &led_wifi_red;
|
||||
led-upgrade = &led_wifi_red;
|
||||
led-running = &led_wifi_red;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-override = "console=ttyS0,115200n8";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory@40000000 {
|
||||
reg = <0 0x40000000 0 0x10000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_wifi_blue: wifi-blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
gpios = <&pio 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wifi_green: wifi-green {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wifi_red: wifi-red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
gpios = <&pio 34 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_lan: lan-blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
gpios = <&pio 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
status = "okay";
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
nvmem-cells = <&macaddr_factory_e000 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: spi-nand@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <52000000>;
|
||||
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x00000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0100000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x0200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x4 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_factory_8000: macaddr@8000 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x8000 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_factory_e000: macaddr@e000 {
|
||||
compatible = "mac-base";
|
||||
reg = <0xe000 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0x4000000>;
|
||||
compatible = "linux,ubi";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
|
||||
band@0 {
|
||||
reg = <0>;
|
||||
nvmem-cells = <&macaddr_factory_4 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
band@1 {
|
||||
reg = <1>;
|
||||
nvmem-cells = <&macaddr_factory_8000 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
@ -68,6 +68,11 @@ bazis,ax3000wm)
|
||||
ucidef_set_led_netdev "lanlink" "LANLINK" "green:lan" "eth1" "link"
|
||||
ucidef_set_led_netdev "internet" "internet" "blue:wan-online" "wan" "link"
|
||||
;;
|
||||
comfast,cf-xr186)
|
||||
ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0" "link tx rx"
|
||||
ucidef_set_led_netdev "wlan2g" "WLAN2G" "green:wlan" "phy0-ap0" "link tx rx"
|
||||
ucidef_set_led_netdev "wlan5g" "WLAN5G" "blue:wlan" "phy1-ap0" "link tx rx"
|
||||
;;
|
||||
cudy,re3000-v1|\
|
||||
kebidumei,ax3000-u22|\
|
||||
wavlink,wl-wn573hx3)
|
||||
|
||||
@ -112,6 +112,7 @@ mediatek_setup_interfaces()
|
||||
cudy,ap3000wall-v1)
|
||||
ucidef_set_interface_lan "lan1 lan2 lan3 lan4 lan5"
|
||||
;;
|
||||
comfast,cf-xr186|\
|
||||
cudy,ap3000outdoor-v1|\
|
||||
cudy,ap3000-v1|\
|
||||
cudy,re3000-v1|\
|
||||
|
||||
@ -1032,6 +1032,27 @@ define Device/comfast_cf-wr632ax-ubootmod
|
||||
endef
|
||||
TARGET_DEVICES += comfast_cf-wr632ax-ubootmod
|
||||
|
||||
define Device/comfast_cf-xr186
|
||||
DEVICE_VENDOR := COMFAST
|
||||
DEVICE_MODEL := CF-XR186
|
||||
DEVICE_DTS := mt7981b-comfast-cf-xr186
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
SUPPORTED_DEVICES += cf-xr186
|
||||
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
|
||||
KERNEL := kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
||||
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += comfast_cf-xr186
|
||||
|
||||
define Device/confiabits_mt7981
|
||||
DEVICE_VENDOR := Confiabits
|
||||
DEVICE_MODEL := MT7981
|
||||
|
||||
Loading…
Reference in New Issue
Block a user