From ca825537fbafee49f6608e5e696316fd85da3f8b Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Jakub=20Van=C4=9Bk?= Date: Mon, 2 Mar 2026 21:14:28 +0100 Subject: [PATCH] mediatek: filogic: add support for Cudy M3000 w/ YT8821 PHY MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The hardware is very close the the Cudy M3000 v1 (see commit 20e4a18feb3f). However, the Motorcomm YT8821 PHY is tricky to support because of a MDIO address collision within the router. Specification: - MT7981BA CPU: dual-core ARM Cortex-A53 @ 1.3 GHz - 256 MiB RAM - 128 MiB SPI NAND - Ethernet: - 1x 1GbE LAN port driven by the internal MT7981 PHY - 1x 2.5GbE WAN port driven by the Motorcomm YT8821 - WiFi: - MT7981BA 2.4 GHz WiFi with 2x2:2 MIMO - MT7981BA 5 GHz WiFi with 2x3:2 MIMO - Buttons: Reset, WPS - LED: 1x combined red/white How to know if you have the a router with the YT8821 PHY: - Boot the router into the vendor's firmware. Go to Diagnostic Tools -> System Log. Try searching for "rtl8221b". - If there are some matches, you have the Cudy M3000 router with the Realtek PHY and you should NOT use the device defined in this commit. Instead, you should use the device defined in mt7981b-cudy-m3000-v1.dts. - If there are no matches, try searching for "yt8821". If that matches something, you have the Cudy M3000 with the Motorcomm PHY and you should use this device tree (mt7981b-cudy-m3000-v2-yt8821.dts). - If even the yt8821 string did not match anything, then something is wrong. Rebooting the router might help (the system log would be refreshed). Installation via the Cudy web UI: - Download the signed intermediary firmware from https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj - Flash the intermediary firmware using the Cudy web UI - Connect a PC/laptop to the "1Gbps LAN" port - Open http://192.168.1.1 in your browser, log in (the password should be empty) - Flash your desired OpenWrt firmware via LuCI - The router should reboot into the desired firmware How to access UART (citing from 20e4a18feb3f): - remove rubber ring on the bottom - remove screws - pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver - remove the (3) screws holding the board in the frame - remove the board from the frame to get to the screws for the silver, flat heat shield - remove the (3) screws holding the heat shield - solder UART pins to the back of the board - make sure to have the pins point out on side with the black, finned heat spread - the markings for the pins are going to be below the silver heat shield - Vcc is not needed - the UART parameters are 115200 baud, 8n1 Installation via UART (citing from 20e4a18feb3f): - attach an Ethernet cable to the "1Gbps LAN" port on the router - hold the reset button while powering the router - press CTRL-C or wait for the timeout to get to the U-Boot prompt - prepare a TFTP server on the network to supply ..-initramfs-kernel.bin - use 'tftpboot 0x46000000 ..-initramfs-kernel.bin' in the U-Boot shell to pull the image (change the file name accordingly) - boot the image using 'bootm 0x46000000' - push the ..-sysupgrade to the router using your preferred method - perform the upgrade with 'sysupgrade -n' Signed-off-by: Jakub Vaněk Link: https://github.com/openwrt/openwrt/pull/22259 (cherry picked from commit 45b51ebaff51d2a49d149e9011717abb1b032683) Signed-off-by: Jakub Vaněk Link: https://github.com/openwrt/openwrt/pull/22423 Signed-off-by: Hauke Mehrtens --- .../lib/preinit/05_set_preinit_iface | 1 + .../mediatek/dts/mt7981b-cudy-m3000-v1.dts | 192 +---------------- .../dts/mt7981b-cudy-m3000-v2-yt8821.dts | 22 ++ .../mediatek/dts/mt7981b-cudy-m3000.dtsi | 195 ++++++++++++++++++ .../filogic/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 1 + target/linux/mediatek/image/filogic.mk | 22 ++ 7 files changed, 244 insertions(+), 190 deletions(-) create mode 100644 target/linux/mediatek/dts/mt7981b-cudy-m3000-v2-yt8821.dts create mode 100644 target/linux/mediatek/dts/mt7981b-cudy-m3000.dtsi diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface index b43d223da6..f99217621d 100644 --- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface +++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface @@ -2,6 +2,7 @@ set_preinit_iface() { case $(board_name) in bazis,ax3000wm|\ cudy,m3000-v1|\ + cudy,m3000-v2-yt8821|\ cudy,tr3000-256mb-v1|\ cudy,tr3000-v1|\ cudy,tr3000-v1-ubootmod|\ diff --git a/target/linux/mediatek/dts/mt7981b-cudy-m3000-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-m3000-v1.dts index 5cbd683418..05e7d57045 100644 --- a/target/linux/mediatek/dts/mt7981b-cudy-m3000-v1.dts +++ b/target/linux/mediatek/dts/mt7981b-cudy-m3000-v1.dts @@ -2,106 +2,15 @@ /dts-v1/; -#include "mt7981b.dtsi" +#include "mt7981b-cudy-m3000.dtsi" / { model = "Cudy M3000 v1"; compatible = "cudy,m3000-v1", "mediatek,mt7981"; - - aliases { - label-mac-device = &gmac0; - led-boot = &led_status; - led-failsafe = &led_status; - led-running = &led_status; - led-upgrade = &led_status; - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - gpio-keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&pio 1 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&pio 0 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - - led_status: internet-white { - function = LED_FUNCTION_WAN_ONLINE; - color = ; - gpios = <&pio 10 GPIO_ACTIVE_LOW>; - }; - - internet-red { - function = LED_FUNCTION_WAN_ONLINE; - color = ; - gpios = <&pio 4 GPIO_ACTIVE_LOW>; - }; - - wan { - function = LED_FUNCTION_WAN; - color = ; - gpios = <&pio 5 GPIO_ACTIVE_LOW>; - }; - - lan { - function = LED_FUNCTION_LAN; - color = ; - gpios = <&pio 9 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&uart0 { - status = "okay"; -}; - -&watchdog { - status = "okay"; -}; - -ð { - pinctrl-names = "default"; - pinctrl-0 = <&mdio_pins>; - status = "okay"; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; - phy-handle = <&rtl8221b_phy>; - - nvmem-cell-names = "mac-address"; - nvmem-cells = <&macaddr_bdinfo_de00 0>; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "gmii"; - phy-handle = <&int_gbe_phy>; - - nvmem-cell-names = "mac-address"; - nvmem-cells = <&macaddr_bdinfo_de00 1>; - }; }; &mdio_bus { - rtl8221b_phy: ethernet-phy@1 { + wan_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c45"; reg = <1>; reset-assert-us = <100000>; @@ -111,100 +20,3 @@ interrupt-parent = <&pio>; }; }; - -&spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spi0_flash_pins>; - status = "okay"; - - spi_nand: spi_nand@0 { - compatible = "spi-nand"; - reg = <0>; - - spi-max-frequency = <52000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - - mediatek,nmbm; - mediatek,bmt-max-ratio = <1>; - mediatek,bmt-max-reserved-blocks = <64>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "BL2"; - reg = <0x0000000 0x0100000>; - read-only; - }; - - partition@100000 { - label = "u-boot-env"; - reg = <0x0100000 0x0080000>; - }; - - factory: partition@180000 { - label = "Factory"; - reg = <0x0180000 0x0200000>; - read-only; - }; - - bdinfo: partition@380000 { - label = "bdinfo"; - reg = <0x0380000 0x0040000>; - read-only; - - nvmem-layout { - compatible = "fixed-layout"; - #address-cells = <1>; - #size-cells = <1>; - - macaddr_bdinfo_de00: macaddr@de00 { - #nvmem-cell-cells = <1>; - compatible = "mac-base"; - reg = <0xde00 0x6>; - }; - }; - }; - - partition@3c0000 { - label = "FIP"; - reg = <0x03c0000 0x0200000>; - read-only; - }; - - partition@5c0000 { - label = "ubi"; - reg = <0x05c0000 0x4000000>; - }; - }; - }; -}; - -&pio { - spi0_flash_pins: spi0-pins { - mux { - function = "spi"; - groups = "spi0", "spi0_wp_hold"; - }; - - conf-pu { - pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; - drive-strength = ; - bias-pull-up = ; - }; - - conf-pd { - pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; - drive-strength = ; - bias-pull-down = ; - }; - }; -}; - -&wifi { - status = "okay"; - mediatek,mtd-eeprom = <&factory 0x0>; -}; diff --git a/target/linux/mediatek/dts/mt7981b-cudy-m3000-v2-yt8821.dts b/target/linux/mediatek/dts/mt7981b-cudy-m3000-v2-yt8821.dts new file mode 100644 index 0000000000..0922b318e1 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-cudy-m3000-v2-yt8821.dts @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "mt7981b-cudy-m3000.dtsi" + +/ { + model = "Cudy M3000 v2 with Motorcomm YT8821"; + compatible = "cudy,m3000-v2-yt8821", "mediatek,mt7981"; +}; + +&mdio_bus { + wan_phy: ethernet-phy@1 { + compatible = "ethernet-phy-id4f51.ea19"; + reg = <1>; + reset-assert-us = <100000>; + reset-deassert-us = <100000>; + reset-gpios = <&pio 39 GPIO_ACTIVE_LOW>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&pio>; + }; +}; diff --git a/target/linux/mediatek/dts/mt7981b-cudy-m3000.dtsi b/target/linux/mediatek/dts/mt7981b-cudy-m3000.dtsi new file mode 100644 index 0000000000..c6fa571e86 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-cudy-m3000.dtsi @@ -0,0 +1,195 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "mt7981b.dtsi" + +/ { + aliases { + label-mac-device = &gmac0; + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status: internet-white { + function = LED_FUNCTION_WAN_ONLINE; + color = ; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + internet-red { + function = LED_FUNCTION_WAN_ONLINE; + color = ; + gpios = <&pio 4 GPIO_ACTIVE_LOW>; + }; + + wan { + function = LED_FUNCTION_WAN; + color = ; + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + }; + + lan { + function = LED_FUNCTION_LAN; + color = ; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + phy-handle = <&wan_phy>; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_bdinfo_de00 0>; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_bdinfo_de00 1>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: spi_nand@0 { + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0000000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x0180000 0x0200000>; + read-only; + }; + + bdinfo: partition@380000 { + label = "bdinfo"; + reg = <0x0380000 0x0040000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_bdinfo_de00: macaddr@de00 { + #nvmem-cell-cells = <1>; + compatible = "mac-base"; + reg = <0xde00 0x6>; + }; + }; + }; + + partition@3c0000 { + label = "FIP"; + reg = <0x03c0000 0x0200000>; + read-only; + }; + + partition@5c0000 { + label = "ubi"; + reg = <0x05c0000 0x4000000>; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&wifi { + status = "okay"; + mediatek,mtd-eeprom = <&factory 0x0>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 9a41600c32..eb348a6ac5 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -128,6 +128,7 @@ mediatek_setup_interfaces() ;; bazis,ax3000wm|\ cudy,m3000-v1|\ + cudy,m3000-v2-yt8821|\ cudy,tr3000-256mb-v1|\ cudy,tr3000-v1|\ cudy,tr3000-v1-ubootmod|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index ea31a60308..5a3322e6aa 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -92,6 +92,7 @@ case "$board" in cudy,ap3000wall-v1|\ cudy,ap3000-v1|\ cudy,m3000-v1|\ + cudy,m3000-v2-yt8821|\ cudy,re3000-v1|\ cudy,tr3000-256mb-v1|\ cudy,tr3000-v1|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 6acf5f2620..7e5e83942d 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -1122,6 +1122,28 @@ define Device/cudy_m3000-v1 endef TARGET_DEVICES += cudy_m3000-v1 +define Device/cudy_m3000-v2-yt8821 + DEVICE_VENDOR := Cudy + DEVICE_MODEL := M3000 + DEVICE_VARIANT := v2 with Motorcomm YT8821 + DEVICE_DTS := mt7981b-cudy-m3000-v2-yt8821 + DEVICE_DTS_DIR := ../dts + SUPPORTED_DEVICES += R37 + DEVICE_DTS_LOADADDR := 0x44000000 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + KERNEL_IN_UBI := 1 + KERNEL := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware kmod-phy-motorcomm +endef +TARGET_DEVICES += cudy_m3000-v2-yt8821 + define Device/cudy_re3000-v1 DEVICE_VENDOR := Cudy DEVICE_MODEL := RE3000