diff --git a/target/linux/ipq40xx/dts/qcom-ipq4029-wired-qca-common.dtsi b/target/linux/ipq40xx/dts/qcom-ipq4029-wired-qca-common.dtsi deleted file mode 100644 index cce0703f07..0000000000 --- a/target/linux/ipq40xx/dts/qcom-ipq4029-wired-qca-common.dtsi +++ /dev/null @@ -1,411 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * Device Tree Source for Meraki "wired-arm-qca" series - * - * Copyright (C) 2017 Chris Blake - * Copyright (C) 2017 Christian Lamparter - * Copyright (C) 2025 Hal Martin - * - */ - -#include "qcom-ipq4019.dtsi" -#include -#include -#include -#include - -/ { - aliases { - led-boot = &status_green; - led-failsafe = &status_red; - led-running = &status_green; - led-upgrade = &power_orange; - }; - - soc { - /* It is a 56-bit counter that supplies the count to the ARM arch - timers and without upstream driver */ - counter@4a1000 { - compatible = "qcom,qca-gcnt"; - reg = <0x4a1000 0x4>; - }; - - ess_tcsr@1953000 { - compatible = "qcom,tcsr"; - reg = <0x1953000 0x1000>; - qcom,ess-interface-select = ; - }; - - tcsr@1949000 { - compatible = "qcom,tcsr"; - reg = <0x1949000 0x100>; - qcom,wifi_glb_cfg = ; - }; - - tcsr@194b000 { - /* select hostmode */ - compatible = "qcom,tcsr"; - reg = <0x194b000 0x100>; - qcom,usb-hsphy-mode-select = ; - status = "okay"; - }; - - tcsr@1957000 { - compatible = "qcom,tcsr"; - reg = <0x1957000 0x100>; - qcom,wifi_noc_memtype_m0_m2 = ; - }; - - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - -}; - -&blsp_dma { - status = "okay"; -}; - -&blsp1_uart1 { - pinctrl-0 = <&serial_0_pins>; - pinctrl-names = "default"; - status = "okay"; -}; - -&cryptobam { - status = "okay"; -}; - -&blsp1_i2c3 { - pinctrl-0 = <&i2c_0_pins>; - pinctrl-names = "default"; - status = "okay"; - - eeprom@50 { - compatible = "atmel,24c64"; - pagesize = <32>; - reg = <0x50>; - read-only; /* This holds our MAC & Meraki board-data */ - - nvmem-layout { - compatible = "fixed-layout"; - #address-cells = <1>; - #size-cells = <1>; - - mac_address: mac-address@66 { - compatible = "mac-base"; - reg = <0x66 0x6>; - #nvmem-cell-cells = <1>; - }; - }; - }; -}; - -&blsp1_i2c4 { - pinctrl-0 = <&i2c_1_pins>; - pinctrl-names = "default"; - status = "okay"; - - tricolor: led-controller@30 { - compatible = "ti,lp5562"; - reg = <0x30>; - clock-mode = /bits/8 <2>; - enable-gpio = <&tlmm 48 GPIO_ACTIVE_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - /* RGB led */ - status_red: chan@0 { - chan-name = "red:status"; - led-cur = /bits/ 8 <0x20>; - max-cur = /bits/ 8 <0x60>; - reg = <0>; - color = ; - }; - - status_green: chan@1 { - chan-name = "green:status"; - led-cur = /bits/ 8 <0x20>; - max-cur = /bits/ 8 <0x60>; - reg = <1>; - color = ; - }; - - chan@2 { - chan-name = "blue:status"; - led-cur = /bits/ 8 <0x20>; - max-cur = /bits/ 8 <0x60>; - reg = <2>; - color = ; - }; - - chan@3 { - chan-name = "white:status"; - led-cur = /bits/ 8 <0x20>; - max-cur = /bits/ 8 <0x60>; - reg = <3>; - color = ; - }; - }; -}; - -&nand { - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - status = "okay"; - - nand@0 { - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "sbl1"; - reg = <0x00000000 0x00100000>; - read-only; - }; - partition@100000 { - label = "mibib"; - reg = <0x00100000 0x00100000>; - read-only; - }; - partition@200000 { - label = "bootconfig"; - reg = <0x00200000 0x00100000>; - read-only; - }; - partition@300000 { - label = "qsee"; - reg = <0x00300000 0x00100000>; - read-only; - }; - partition@400000 { - label = "qsee_alt"; - reg = <0x00400000 0x00100000>; - read-only; - }; - partition@500000 { - label = "cdt"; - reg = <0x00500000 0x00080000>; - read-only; - }; - partition@580000 { - label = "cdt_alt"; - reg = <0x00580000 0x00080000>; - read-only; - }; - partition@600000 { - label = "ddrparams"; - reg = <0x00600000 0x00080000>; - read-only; - }; - partition@700000 { - label = "u-boot"; - reg = <0x00700000 0x00200000>; - read-only; - }; - partition@900000 { - label = "u-boot-backup"; - reg = <0x00900000 0x00200000>; - read-only; - }; - partition@b00000 { - label = "ART"; - reg = <0x00b00000 0x00080000>; - read-only; - }; - partition@c00000 { - compatible = "linux,ubi"; - reg = <0x00c00000 0x07000000>; - label = "ubi"; - /* - * Do not try to allocate the remaining - * 4 MiB to this ubi partition. It will - * confuse the u-boot and it might not - * find the kernel partition anymore. - */ - volumes { - ubi_art: ubi-volume-art { - volname = "ART"; - }; - }; - }; - }; - }; -}; - -&qpic_bam { - status = "okay"; -}; - -&mdio { - status = "okay"; - pinctrl-0 = <&mdio_pins>; - pinctrl-names = "default"; -}; - -&tlmm { - mdio_pins: mdio_pinmux { - mux_1 { - pins = "gpio6"; - function = "mdio"; - bias-pull-up; - }; - mux_2 { - pins = "gpio7"; - function = "mdc"; - bias-pull-up; - }; - }; - - serial_0_pins: serial_pinmux { - pins = "gpio16", "gpio17"; - function = "blsp_uart0"; - bias-disable; - }; - - serial_1_pins: serial1_pinmux { - /* We use the i2c-0 pins for serial_1 */ - pins = "gpio8", "gpio9"; - function = "blsp_uart1"; - bias-disable; - }; - - i2c_0_pins: i2c_0_pinmux { - function = "blsp_i2c0"; - pins = "gpio20", "gpio21"; - drive-strength = <16>; - bias-disable; - }; - - i2c_1_pins: i2c_1_pinmux { - function = "blsp_i2c1"; - pins = "gpio34", "gpio35"; - drive-strength = <16>; - bias-disable; - }; - - nand_pins: nand_pins { - /* - * There are 18 pins. 15 pins are common between LCD and NAND. - * The QPIC controller arbitrates between LCD and NAND. Of the - * remaining 4, 2 are for NAND and 2 are for LCD exclusively. - * - * The meraki source hints that the bluetooth module claims - * pin 52 as well. But sadly, there's no data whenever this - * is a NAND or LCD exclusive pin or not. - */ - - pullups { - pins = "gpio53", "gpio58", "gpio59"; - function = "qpic"; - bias-pull-up; - }; - - pulldowns { - pins = "gpio55", "gpio56", - "gpio57", "gpio60", "gpio62", - "gpio63", "gpio64", "gpio65", - "gpio66", "gpio67", "gpio68", - "gpio69"; - function = "qpic"; - bias-pull-down; - }; - }; -}; - -&usb2_hs_phy { - status = "okay"; -}; - -&usb2 { - status = "okay"; -}; - -&usb3_hs_phy { - status = "okay"; -}; - -&usb3_ss_phy { - status = "okay"; -}; - -&usb3 { - status = "okay"; -}; - -&ubi_art { - nvmem-layout { - compatible = "fixed-layout"; - #address-cells = <1>; - #size-cells = <1>; - - precal_factory_1000: precal@1000 { - reg = <0x1000 0x2f20>; - }; - - precal_factory_5000: precal@5000 { - reg = <0x5000 0x2f20>; - }; - - cal_factory_9000: cal@9000 { - reg = <0x9000 0x844>; - }; - }; -}; - -&wifi0 { - status = "okay"; - nvmem-cells = <&precal_factory_1000>; - nvmem-cell-names = "pre-calibration"; -}; - -&wifi1 { - status = "okay"; - nvmem-cells = <&precal_factory_5000>; - nvmem-cell-names = "pre-calibration"; -}; - -&gmac { - status = "okay"; - nvmem-cells = <&mac_address 0>; - nvmem-cell-names = "mac-address"; -}; - -&switch { - status = "okay"; -}; - -&swport1 { - label = "wan"; - status = "okay"; -}; - -&swport2 { - label = "lan2"; - status = "okay"; -}; - -&swport3 { - label = "lan3"; - status = "okay"; -}; - -&swport4 { - label = "lan4"; - status = "okay"; -}; - -&swport5 { - label = "lan5"; - status = "okay"; -};