The pppox module is a dependency of pppoe/pptp/pppol2tp and does not
have a separate Kconfig symbol.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23077
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The netifd/dhcp flow uses this, and as uxc mounts netifd in a
container, this allows not mounting `basename` for just a usage.
References: https://github.com/openwrt/procd/pull/34
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Andre Heider <a.heider@gmail.com>
The basic AN7581 NPU FW also supports WiFi offload for MT7992 WiFi chip.
Add this information in the package description to clarify this.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
6.14 has introduced a DRM client setup library. Add kmod-drm-client-lib
to support it, and add it as a dependency to DRM modules which depend on it.
Link: https://github.com/openwrt/openwrt/pull/22975
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is required to build the motorcomm dwmac driver which is widely
used on loongson platforms.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/22923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Motorcomm YT6801 is a PCIe ethernet controller based on DWMAC4 IP. It
integrates an GbE phy, supporting WOL, VLAN tagging and various types
of offloading. It ships an on-chip eFuse for storing various vendor
configuration, including MAC address.
The PM and plat_data functions were slightly modified to build with
current kernel.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/22923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
GCC15 defaults to C23, which does not work here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23042
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux commit 09371e1349c9 ("lib/crypto: powerpc/md5: Migrate optimized code into library")
removed the PowerPC-specific MD5 implementation (md5-ppc.ko) and
replaced it with an optimized library implementation in lib/crypto.
As a result, CONFIG_CRYPTO_MD5_PPC and the module
arch/powerpc/crypto/md5-ppc.ko no longer exist in kernels >= 6.18.
Link: https://github.com/openwrt/openwrt/pull/22732
Signed-off-by: Nick Hainke <vincent@systemli.org>
The sama5d4_xplained_nandflash target incorrectly references microchip_sama5d3-xplained as its BUILD_DEVICES value.
This appears to be a copy-paste error, as all other SAMA5D4 Xplained targets (e.g. mmc and spiflash) correctly use microchip_sama5d4-xplained. The target name itself also clearly refers to the SAMA5D4 platform.
In addition, the SAMA5D3 Xplained and SAMA5D4 Xplained boards use different NAND flash hardware and configurations, so pointing the nandflash target to a SAMA5D3 device is incorrect and may lead to invalid builds or runtime issues.
Fix the inconsistency by updating BUILD_DEVICES to microchip_sama5d4-xplained, aligning the nandflash target with the rest of the SAMA5D4 definitions and ensuring the correct device mapping.
Signed-off-by: Cerrone Diamant <cerrone@tutamail.com>
Link: https://github.com/openwrt/openwrt/pull/23022
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patches to fix build failures on musl-based toolchains:
0002-xdpsock-fix-struct-ethhdr-redefinition-on-musl.patch:
xdpsock.c included <net/ethernet.h> and <netinet/ether.h> alongside
<linux/if_ether.h>, triggering a struct ethhdr redefinition on musl.
Replace BSD-style ether_header/ether_addr with struct ethhdr and drop
the conflicting includes.
0003-build-use-gnu2x-to-avoid-stdbool.h-dependency.patch:
Switch CFLAGS and BPF_CFLAGS from -std=gnu11 to -std=gnu2x. In C23,
bool is a native keyword, fixing "stdbool.h: No such file or directory"
errors with a clang lacking its resource directory (e.g. llvm-bpf built
with LLVM_INSTALL_TOOLCHAIN_ONLY=ON on musl targets).
Link: https://github.com/openwrt/openwrt/pull/22983
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch http:// (and redundant ftp://) PKG_SOURCE_URL entries to https://
across tools/ and package/. PKG_HASH alone does not protect against an
attacker tampering with insecure downloads when a maintainer regenerates
the hash via `make ... FIXUP=1`: HTTPS authenticates the upstream so the
captured hash reflects real upstream content.
In-place http -> https (HTTPS reachability verified per host):
- tools/elftosb, tools/lzop, tools/liblzo, tools/mpfr, tools/dosfstools,
tools/libressl, tools/xz
- package/libs/mpfr, package/libs/libmnl, package/libs/libnfnetlink
Replaced with @OPENWRT (HTTPS-only mirror) where the upstream HTTPS host
is dead or has a broken certificate:
- package/libs/popt (ftp.rpm.org cert mismatch)
- package/firmware/ixp4xx-microcode (was http://downloads.openwrt.org)
- package/boot/imx-bootlets (trabant.uid0.hu cert mismatch)
- package/boot/kobs-ng (freescale.com URL is dead, redirects to nxp.com root)
Dropped redundant ftp://ftp.denx.de fallback (https://ftp.denx.de is
already listed):
- package/boot/uboot-tools, tools/mkimage
Signed-off-by: Paul Spooren <mail@aparcar.org>
Release Notes:
- https://github.com/libbpf/bpftool/releases/tag/v7.7.0
Backport upstream commit 9ba0b4add39e ("bpftool: Allow explicitly skip
llvm, libbfd and libcrypto dependencies") to fix a linker error. The
bpftool only needs skeleton generation, not program signing, so pass
SKIP_CRYPTO=1 to drop the libcrypto dependency entirely.
Link: 9ba0b4add3
Link: https://github.com/openwrt/openwrt/pull/22973
Signed-off-by: Nick Hainke <vincent@systemli.org>
ld.bfd is the default/only implementation for now but things may change in future.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21997
Signed-off-by: Nick Hainke <vincent@systemli.org>
Support for obsolete versions was dropped in upstream commit 72731b445e.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21997
Signed-off-by: Nick Hainke <vincent@systemli.org>
The by-now-upstream driver for the built-in 2.5GE PHY of the MediaTek
MT7988 and MT7987 SoC loads firmware at probe time.
Build the driver as a module in order to make sure the driver only
attempts to load the firmware by the time the rootfs with the firmware
file has become available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for BUFFALO WSR-3000AX4P, to allow updating environment
variables of U-Boot on that device.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22587
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Exclude more apk related files from the sysupgrade backup list when
using the various options that scan /etc for changes.
Ensure removal of the system generated distfeeds list, as that
contains kernel- and version-specific urls and should never be
retained.
Also exclude any '*.apk-new' files, equivalent to the old '*-opkg'
files, which may have been created during package installation.
Example before
$ sysupgrade -l -c | grep apk
/etc/apk/keys/buildroot.pem
/etc/apk/repositories.d/customfeeds.list
/etc/apk/repositories.d/distfeeds.list
/etc/owut.d/pre-install.sh.apk-new
/etc/config/adblock.apk-new
After
$ sysupgrade -l -c | grep apk
/etc/apk/keys/buildroot.pem
/etc/apk/repositories.d/customfeeds.list
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22937
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device has a redundant configuration. Important when writing to it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22882
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes:
ifxmips_aes.c: In function 'gcm_aes_decrypt':
ifxmips_aes.c:1803:14: error: assignment discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1803 | temp = walk.src.virt.addr;
| ^
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22921
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes:
ltq_atm.c: In function 'ltq_atm_probe':
ltq_atm.c:1840:36: error: passing argument 2 of 'platform_set_drvdata' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1840 | platform_set_drvdata(pdev, ops);
| ^~~
In file included from ltq_atm.c:40:
/workspaces/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/linux-6.18.21/include/linux/platform_device.h:276:47: note: expected 'void *' but argument is of type 'const struct ltq_atm_ops *'
276 | void *data)
| ~~~~~~^~~~
Fixes: c1fa85f659 ("treewide: use of_device_get_match_data")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22921
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 6.18 code works with older kernels as well. Remove the older section
and use the newer one always.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22925
Signed-off-by: Robert Marko <robimarko@gmail.com>
When we cross build uboot-tools, the dtc tool is still compiled for
the host. Therefore, we should not attempt to link the OpenWrt system
libraries. CPU architecture mismatch can lead to build errors.
Fixes: https://github.com/openwrt/openwrt/issues/22924
Fixes: 55925650aa ("uboot-tools: update to v2026.04")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22927
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
The device is similar to the M30 but has only one LAN port and no WAN port.
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 2 buttons (WPS, reset, LED)
- 1 1Gbit LAN port
Disassembly:
- There are two screws at the power connector which must be removed. Afterwards the top case can be removed (it is clipped on, so some tools are required).
Serial Interface:
- The serial interface can be connected to the 4 pin holes on the board. Do NOT connect VCC.
- The pins are labelled on the PCB (RX, TX, GND)
- Settings: 115200, 8N1
MAC addresses:
- LAN MAC is stored in partition "Odm" at offset 0x8f
- WLAN MAC (2.4 GHz and 5GHz) is LAN MAC + 1
Reverting back to OEM firmware:
- There is currently no easy way to revert back to the OEM image
- The methods from M30 and M60 doesn't seem to work anymore
- If you plan to revert back to OEM firmware later, do the following steps before flashing OpenWrt:
- Boot from initramfs as described in "Flashing via U-Boot" but don't flash anything
- Instead, make a backup of UBI and UBI1 partition
- The created dumps must be written to the initial partitions to revert back to OEM
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.50/ (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-recovery.bin
- Note: The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If flashing was successful, OpenWrt is accessible via 192.168.1.1
- The recovery image boots an initramfs image, flash the sys upgrade image to get to „normal“ OpenWrt mode
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-initramfs-kernel.bin
- Supply the board with 12V
- Select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The check of files from packages was only checking opkg files.
Check for apk as well and fail if both are missing.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17847
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The list of files excluded from backup was outdated.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17847
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace conditional "LINUX_6_12:mod" / "!LINUX_6_12:mod" AUTOLOAD entries
with version-filtered module names using @lt6.18 / @ge6.18. This makes
version_filter emit plain module names into /etc/modules.d(e.g. "crc32c_generic"),
allowing kmodloader to find and load the correct module for the running kernel.
Fixes crc32c (and related crypto modules) not being autoloaded on 6.12 kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EDUP EP-RT2983 comes with a factory installed version of OpenWrt 23.05
with device name "netis,n6".
Specification
--------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (Toshiba)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x WiFi (green)
1x Mesh/WPS (green); flashing green during boot
3x LAN (green)
1x WAN (green); flashing red during upgrade and failsafe
- Power : 12 VDC 1A
Installation
-------------
1. Log in to LuCI
2. Go to System, Backup / Flash Firmware
3. If desired, backup the current system by saving (all) the mtdblock
contents.
4. Flash new firmware image, select Flash image.
5. Browse and select the sysupgrade file
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-sysupgrade.bin"
and then Upload.
6. Unselect "Keep settings and retain the current configuration"
Note: All settings will be reset to default. WiFi is not enabled by
default so a connection via Ethernet is necessary to log in and set up.
7. Allow "Force upgrade" (tick the box if there is one), or press Continue
if there is no box to tick. This is because the name is now
"edup,ep-rt2983" as it should have been from the start.
8. Proceed to flash. Wait for reboot and keep power connected.
9. After reboot, default address to access LuCI is 192.168.1.1 with
no password
Recovery (UART)
----------------
1. Remove the 4 screws on the bottom and pry open the cover.
2. Connect serial adapter to the unpopulated serial header pins
TX, RX, GND near the WPS button. Do not connect VCC.
3. Start serial terminal (e.g. minicom, screen, etc) on the computer and
turn on the router.
4. As prompted, hit any key to stop autoboot.
5. Enter 2 to select "2. Upgrade firmware"
6. Enter 0 to select "0 - TFTP client (Default)"
7. Accept the defaults by pressing Enter for
"Input U-Boot's IP address: 192.168.1.1",
"TFTP server's IP address: 192.168.1.2",
"Input IP netmask: 255.255.255.0"
8. Assign your PC's Ethernet port a static IP 192.168.1.2 with netmask
255.255.255.0 and connect to a LAN port on the router using the
Ethernet cable. Disconnect all other network connections (e.g. WiFi) on
the computer.
9. Serve the factory image
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-factory.bin" using
a TFTP server, e.g. tftpd64. For convenience, the filename can be renamed
to something shorter.
10. In the serial terminal, when prompted "Input file name:", enter the
filename from the previous step and press Enter.
11. The factory image will be flashed as indicated. Wait for reboot.
MAC addresses prototype
------------------------
+---------+---------------------+
| | MAC example |
+---------+---------------------+
| LAN | CC:D8:1F:47:xx:yy |
| WAN | CC:D8:1F:47:xx:yy+1 |
| WLAN 2G | CC:D8:1F:17:xx:yy+2 |
| WLAN 5G | CC:D8:1F:77:xx:yy+2 |
+---------+---------------------+
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this, max_oper_chwidth is set incorrectly,
thus ibss_mesh_select_80_160mhz fails to set the correct channel width
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22644
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a safer way to operate the .config file.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22845
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update to the latest stable version. Also add PKG_CONFIG_SYSROOT_DIR
make flag to fix dtc tools build without yaml[1-2].
Patches manually refreshed:
* 003-tools-dumpimage-fix-tools-compile.patch
[1] 0535e46d55
[2] 807bcd844a
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22845
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add support for the Zyxel GS1900-48HP A1 managed PoE switch based on
RTL8393 SoC with 48 copper ports (6x RTL8218B), 2 SFP slots and PoE
(170W budget). Includes DTS, image definition, network config and
u-boot-env support.
The device has 48 copper ports but only ports 1-24 are powered by
the PoE PSE controller.
PoE support requires the realtek-poe package from the packages feed
with an additional configuration for PSE ID 7 to address the MCU on
this device.
Signed-off-by: Klaus Rubenstein <klaus.rubenstein@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Bump the bundled software pieces to their current version too.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22863
Signed-off-by: Robert Marko <robimarko@gmail.com>
This release incorporates the following bug fixes and mitigations:
Fixed incorrect failure handling in RSA KEM RSASVE encapsulation.
(CVE-2026-31790)
Fixed loss of key agreement group tuple structure when the DEFAULT keyword
is used in the server-side configuration of the key-agreement group list.
(CVE-2026-2673)
Fixed potential use-after-free in DANE client code.
(CVE-2026-28387)
Fixed NULL pointer dereference when processing a delta CRL.
(CVE-2026-28388)
Fixed possible NULL dereference when processing CMS KeyAgreeRecipientInfo.
(CVE-2026-28389)
Fixed possible NULL dereference when processing CMS
KeyTransportRecipientInfo.
(CVE-2026-28390)
Fixed heap buffer overflow in hexadecimal conversion.
(CVE-2026-31789)
No need refresh patches
Signed-off-by: Jack Sun <sunjiazheng321521@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22847
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rss-input-xfrm workaround for Linux 6.6 is no longer needed with
current kernel versions. Remove the patch and the associated
--enable-rss-input-xfrm configure flag.
Link: https://github.com/openwrt/openwrt/pull/22841
Signed-off-by: Nick Hainke <vincent@systemli.org>
The highlight of this version is that the bl2 size will be reduced
by 60+ KB. The MT7987 SPI interface selection hack was replaced by
upstream implementation with the new symbol SPIM_NAND_PREFER_SPI2.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Migrate timer handling (removed in 6.13) and netdev dummy initialization
(removed in 6.16) to new methods with guards to not break older kernels.
This resolves compilation errors due to missing del_timer_sync(),
from_timer() and init_dummy_netdev().
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/22775
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version fixes some security problems:
* Client impersonation while resuming a TLS 1.3 session
(CVE-2026-34873)
* Entropy on Linux can fall back to /dev/urandom (CVE-2026-34871)
* PSA random generator cloning (CVE-2026-25835)
* Compiler-induced constant-time violations (CVE-2025-66442)
* Null pointer dereference when setting a distinguished name
(CVE-2026-34874)
* Buffer overflow in FFDH public key export (CVE-2026-34875)
* FFDH: lack of contributory behaviour due to improper input validation
(CVE-2026-34872)
* Signature Algorithm Injection (CVE-2026-25834)
* CCM multipart finish tag-length validation bypass (CVE-2026-34876)
* Risk of insufficient protection of serialized session or context data
leading to potential memory safety issues (CVE-2026-34877)
* Buffer underflow in x509_inet_pton_ipv6() (CVE-2026-25833)
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/mbedtls-3.6.6
Size increases by 470 bytes on aarch64:
343995 bin/packages/aarch64_generic/base/libmbedtls21-3.6.5-r1.apk
344465 bin/packages/aarch64_generic/base/libmbedtls21-3.6.6-r1.apk
Link: https://github.com/openwrt/openwrt/pull/22787
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Include the column utility to allow simple formatting of columnar
output.
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22782
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Version 6.19 - Feb 14, 2026
* Feature: support HW timestamp configuration (--set-hwtimestamp-cfg)
* Feature: display HW timestamp source (-T)
* Feature: support PLCA notifications (--get/set-plca-cfg)
* Feature: add PSE priority management support (--show/set-pse)
* Feature: support PSE notifications (--show/set-pse)
* Feature: support configuring RSS on IPv6 Flow Label (-n/-N)
* Feature: support FEC bit error histograms (--show-fec)
* Feature: register dump decoding for TI K3 CPSW and its ALE table (-d)
* Fix: fix missing headers in text output
* Fix: fix print_string when the value is NULL (-Werror=format-security)
* Fix: fix JSON output of SFP diagnostics
* Fix: fix duplicated JSON keys in module info
* Misc: clarify that symmetric RSS may be on by default (-x/-X)
* Misc: add AppStream metainfo file to %files section
Link: https://github.com/openwrt/openwrt/pull/22780
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add missing dependency kmod-ptp to fix the build error. We also
add symbol CONFIG_PTP_1588_CLOCK_OPTIONAL explicitly for kmod-ptp
because it is selected by CONFIG_PTP_1588_CLOCK. Fix:
Package kmod-iavf is missing dependencies for the following libraries:
ptp.ko
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
cryptd has been decoupled from crypto-misc in the 6.18 kernel. Fix:
ERROR: module '/home/runner/work/Actions_/Actions_/openwrt/build_dir/target-i386_pentium4_musl/linux-x86_generic/linux-6.18.20/crypto/cryptd.ko' is missing.
make[3]: *** [modules/crypto.mk:873: /home/runner/work/Actions_/Actions_/openwrt/bin/targets/x86/generic/packages/kmod-crypto-misc-6.18.20-r1.apk] Error 1
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MediaTek T-PHY controller supports multiple usb2.0, usb3.0 ports,
PCIe and SATA. ARM mediatek and ramips/mt7621 targets require this
package to make the XHCI work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was replaced upstream with a proper rng device that feeds into
/dev/random. No need for this anymore.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22766
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ucode path generates different erp_domain and fils_cache_id
values than the legacy shell path due to three mismatches:
1. erp_domain md5 input missing trailing newline (echo adds \n)
2. erp_domain output truncated to 4 chars instead of 8 (shell
uses head -c 8)
3. fils_cache_id md5 input missing trailing newline
4. erp_domain missing fallback to mobility_domain
Same bug pattern as mobility_domain fixed in commit b1dc2736db.
Fixes: #21768
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Signed-off-by: Joshua Klinesmith <joshuaklinesmith@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22677
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Export the unique, monotonic DISKSEQ sequence drive number instead of its
major/minor numbers to identify the boot disk and directly match the partition
in export_partdevice with PARTN.
The MINOR blockdevice numbers are not guaranteed sequential across disks, it
can happen that disks enumerate before their partitions are probed, resulting
in interleaved MINOR numbers breaking the partition offset calculation:
major minor #blocks name
259 0 250059096 nvme0n1
259 2 8192 nvme0n1p1
259 3 491520 nvme0n1p2
259 4 239 nvme0n1p128
259 1 250059096 nvme1n1
259 5 250057728 nvme1n1p1
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Link: https://github.com/openwrt/openwrt/pull/18962
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add some of the more current 4G and 5G modems.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Link: https://github.com/openwrt/openwrt/pull/13426
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The conditional runtime dependency on the ip package was originally
intended to only pull in the ip package when busybox ip is not
configured. However, in APK-based builds the BUSYBOX_CONFIG_*
variables may not be resolvable at package metadata generation
time, causing the ip dependency to be unconditionally baked into
the .apk package. This forces users to install ip-tiny or ip-full
even though busybox already provides the ip command.
Revert to the previous +@BUSYBOX_CONFIG_IP / +@BUSYBOX_CONFIG_FEATURE_IP_LINK
kconfig-level dependencies. These ensure busybox ip support is
enabled at config time without creating a runtime package dependency.
Both options default to y, and wireguard.uc only uses basic
ip link commands that busybox fully supports.
Fixes: openwrt#22637
Signed-off-by: Anand Kumar <anandvtu16158@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22652
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to read u-boot-env partition as sys env
for Zyxel EX5601 and WX5600 with custom partitions.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22670
Signed-off-by: Robert Marko <robimarko@gmail.com>
libunwind solves these in different ways.
ppc-musl is still pending upstream.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21057
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rtl8812au-ct driver is obsolete and replaced by rtw88. It will need
tons of work to compile against 6.18 so for now limit it to 6.12.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update module files for kernel 6.18
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update module files for kernel 6.18
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace the two-step hrtimer initialization pattern with a single
consolidated call to hrtimer_setup().
The legacy approach of calling hrtimer_init() followed by manual
assignment to timer.function is deprecated. The new hrtimer_setup()
helper atomically initializes the timer and assigns the callback
function in one operation, eliminating the race-prone intermediate
state where the timer is initialized but lacks a handler.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reintroduce old-style debugfs file_operations for kernels < 6.14 and
switch the drivers to use debugfs_short_fops + debugfs_create_file_aux
on >= 6.14. This restores compatibility with older kernels while keeping
the new debugfs API working on 6.14+.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch set introduces support for using the in-tree (mainline)
EIP93 crypto driver for kernel 6.18 and later, along with additional
improvements and fixes:
- Conditional Kconfig/Makefile handling for crypto-hw-eip93 to enable use of the mainline driver with kernel 6.18+.
- Patch 926: Use software AES fallback for small requests in the EIP93 driver.
- Patch 927: Add `mediatek,mtk-eip93` compatible string for upstream kernel device trees.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a config option for the 6.18 series of kernels
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Change GPIOF_ACTIVE_LOW to gpiod_toggle_active_low
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport upstream driver and apply pending downstream patches to
support using the MaxLinear MxL86252 and MxL86282 switches.
The driver supports a native proprietary 8-byte DSA special tag format
(mxl862xx) as well as using an 802.1Q-based DSA tag (mxl862xx-8021q).
All basic bridge, VLAN and LAG operations are supported. A single port
can be used as mirror port. Hardware counters are made available as
ethtool stats or directly serve as interface counters (bytes,
packets).
The switch runs a complex ZephyrOS-based firmware on an integrated
ARC microcontroller, the driver uses the firmware management API over
MDIO to interact with the switch hardware.
Note that the firmware needs to be rather recent (WSP 1.0.78 or later)
to work well with this driver. It can be updated at runtime using devlink.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000h-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000h-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000h-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000e-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000e-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000e-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000s-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000s-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000s-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000p-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000p-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000p-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since there are some similar devices from Cudy (only WR3000P now)
this will allow to create OpenWrt U-Boot layout for all of them
using same DDR4 target.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
Doesn't make sense to have he_twt_required enabled without
he_twt_respodner.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22577
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In hostapd conf this option is set to 1 by default.
Then it's set to 0 if the HE MAC capability bit is not present.
Add an option in wifi-scripts to manually control it.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22577
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
a665659dee50 wifi: mt76: fix beacon monitor for MBSSID nontransmitted BSS
1b26f5f63d42 wifi: mt76: mt7996: Decrement sta counter removing the link in mt7996_mac_reset_sta_iter()
0c1dedac48c3 wifi: mt76: mt7996: Switch deflink to seclink only if link lookup does not fail
7fa21be01b97 wifi: mt76: mt7996: Rely on msta_link link_id in mt7996_vif_link_remove()
492a407111c3 wifi: mt76: mt7996: Account active links in valid_links fields
ade83e44eda0 wifi: mt76: mt7996: Move mlink deallocation in mt7996_vif_link_remove()
efebeea5c058 wifi: mt76: mt7996: Destroy vif active links in mt7996_remove_interface()
a4c790aef40d wifi: mt76: mt7996: Add mcu APIs to enable/disable vif links.
018f60316d4d wifi: mt76: mt7996: Destroy active sta links in mt7996_mac_sta_remove()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Modern gawk rejects C-style /* ... */ comments in AWK code, treating
them as regex patterns where '*' has nothing to quantify. Replace all
such comments with AWK-style '#' comments in lantiq_bdi_conf.awk and
lantiq_ram_init_uart.awk.
Also replace the pattern 'if (x) /* comment */ else action' which used
a C comment as a null statement with the equivalent 'if (!x) action'.
Fixes build error:
awk: error: ? * + or {interval} not preceded by valid subpattern
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Link: https://github.com/openwrt/openwrt/pull/22458
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The VF2 boards store their ubootenv on /dev/mtd1 which is a SPI flash
partition. Add support for reading this partition in uboot-envtools,
and add the package into the VF2 image.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add uboot-envtools support for JDCloud RE-CS-02 RE-CS-07 and RE-SS-01
Signed-off-by: Fire Chen <firedevel@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/21787
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
NN6000v1 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: K4B4G1646E-BCMA 512MiB x2 = 1 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (2x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
NN6000v2 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: MT41K512M16VRN-107 IT:P 1GiB x2 = 2 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (4x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
Install via UART:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Install via Uboot WebUI:
- Only work when you flash a custom uboot with webui
- Push the reset button for 5 seconds, then use broswer to
access http://192.168.1.1/, then upload factory.bin.
Signed-off-by: Fire Chen <firedevel@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/21787
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add missing wpabuf_free calls to the hostapd_rrm_nr_set and
hostapd_rrm_beacon_req functions.
Signed-off-by: Vladimir Palevich <palevichva@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22538
Signed-off-by: Nick Hainke <vincent@systemli.org>
The hostapd configuration for SU-BEAMFORMEE was incorrectly using the
beamformer antenna count instead of the beamformee antenna count for the
[BF-ANTENNA-N] capability string.
Fix this by using config.beamformee_antennas instead.
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22511
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
"qca,gpio-mask" used to be read between ath9k_hw_init() and
ath9k_init_queues(). After 12913c3c56
it is read in ath9k_of_init(), but it gets overwritten by
ath9k_gpio_cap_init() during the call of ath9k_hw_init(), and causes
https://github.com/openwrt/openwrt/issues/22340
If keeping the most of 12913c3c56,
ath9k_gpio_cap_init() could be patched to keep the existing non-zero
gpio mask (coming from device tree).
Tested on Netgear WNDR4500 v3:
[ 22.558083] ath9k 0000:00:00.0: enabling device (0000 -> 0002)
[ 22.569548] ath: phy1: Use overridden gpio mask 0xf6ff
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/22376
Signed-off-by: Robert Marko <robimarko@gmail.com>
If the user removes all /lib/apk/packages/*.conffiles* files to prevent
sysupgrade from preserving configuration, the glob no longer matches and
sysupgrade ends up calling cat on a non-existent path:
cat: can't open '/lib/apk/packages/*.conffiles_static': No such file or directory
Fix this by using find cmd.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/22071
Signed-off-by: Robert Marko <robimarko@gmail.com>
No longer used. If swapping is desired, ralink,mtd-eeprom can be used.
Otherwise nvmem.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22207
Signed-off-by: Robert Marko <robimarko@gmail.com>
parent_tsf in struct rrm_measurement_beacon_report is le32 (32-bit),
but was being added with blobmsg_add_u16, truncating the value.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The beacon measurement token was not included in the ubus beacon-report
notification, causing consumers that need the token (e.g. for constructing
Beacon Metrics Response TLVs) to receive null.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use blobmsg_add_u32 for non-bool fields in order to avoid wrong
interpretations of the data on JSON/ucode conversion.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Reporting Detail value is a 1-byte field, but was written as le16,
producing a 2-byte write that also contradicts the length field of 1
in the subelement header.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reporting detail subelement (up to 3 bytes) was not accounted for
in the wpabuf allocation, causing a crash when reporting_detail is set
to a valid value (0, 1, or 2).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
After 02e2065203, it can happen that both,
[VHT160-80PLUS80] and [VHT160] are added to the vht_capab option in
an AP's hostapd.conf, which would cause a failure to start the AP.
Fix the logic in order to prevent such misconfiguration.
Fixes: #22481
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22482
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Nokia Valyrian device that implement similar spec of an
Airoha AN7581 RFB board.
Link: https://github.com/openwrt/openwrt/pull/21761
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use linux-firmware repository for IPQ5018, IPQ8074 and QCN9074.
All officially released firmware versions are available there.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21833
Signed-off-by: Robert Marko <robimarko@gmail.com>
mt76 tracks the PSM state of a sta internally with a wcid flag. TX to
such clients is skipped based on the presence of this flag.
This flag was not added to the PS state notify handler for MT7915 chips.
Without this flag, mt76 queues pending frames to the hardware,
accounting for airtime when a PSM notification is received while in a TX
iteration.
Set the PS flag for the STA WCID to prevent this from happening. TX gets
skipped in presence of this flag.
Link: https://patchwork.kernel.org/project/linux-wireless/patch/20260313112502.2026974-1-mail@david-bauer.net/
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a help text for the new --force-reinstall option, so that users
will actually find the new option.
(Also refresh patches)
Improves: 91cff1a "apk: add --force-reinstall option"
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/22426
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove unmatched endif.
fixes: 2948dbebbf ("mac80211: use OpenWrt mirror for b43 fw downloads")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22430
Signed-off-by: Robert Marko <robimarko@gmail.com>
% git shortlog v1.0.20250521..v1.0.20260223
Doug Freed (1):
wg-quick@.service: add deps on wg-quick.target
Jason A. Donenfeld (8):
wg-quick: linux: use smallest mtu, not largest
syncconf: account for psks removed from config file
wg-quick: linux: deal with resolvconf migration more gracefully
wg-quick: use addconf instead of setconf
wg-quick: linux: do not unnecessarily set sysctl
config: preserve const correctness
syncconf: account for persistent keepalive removed from config file
version: bump
Robyn Kosching (1):
wg-quick: pass on # comments to {Pre,Post}{Up,Down}
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22190
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Release Notes:
https://github.com/madler/zlib/blob/v1.3.2/ChangeLog
We also switch package tarball source to GitHub repository releases
to avoid package hash mismatch after the zstd upgrade.
The 005-* patch was suppressed by the upstream commit 15ba5055a935
("CMake: Adapt pkgconfig-file to the GnuInstallDirs layout.")
This patch also adjust the zlib.pc file path as it was changed in
the latest release.
The mipsel_24kc 'zlib' package size will increase by about 1 kB.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21228
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is no point in printing the missing M3 memory dump adress message
on each boot under the warning level, as not all boards need it at all.
So, degrate it to a debug print with QMI mask.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Originally, the .compatible string for EAP623-Outdoor HD tried to
shorten the "-outdoor" to "od". However, this naming was inconsistent
with the existing "eap610-outdoor". As "od" is not a common shorthand,
spell out the complete word: "eap623-outdoor-hd-v1".
Fixes: 5dbf93c8c5 ("ipq60xx: add support for TP-Link EAP623-Outdoor HD v1")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18804
Signed-off-by: Robert Marko <robimarko@gmail.com>
* e3f6a41 main: exit 1 when showing the usage
* b17c31f main: exit 1 on getopt() errors
* e086664 lexer: fix a minor memleak in jp_get_token()/match_token()
* e5a07f4 main: defer processing until options are processed
* afe72ad main: usage spell fixes
Signed-off-by: Paul Spooren <mail@aparcar.org>
58eb263 instance: don't print error in case cgroups are disabled
9baf019 instance: use positive error numbers for strerror()
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds kernel packages for the Microchip KSZ9477 switch family.
The core package has a target specific dependency as the ksz9477
driver enables DCB which grows the kernel size and can negatively
impact other targets.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/22257
Signed-off-by: Robert Marko <robimarko@gmail.com>
Makes it clear that the allocation is dealing with a flex array member.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21960
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is nearly identical to what landed in ath-next for v7.1, aside from
resolving a couple conflicts. A separate patch has been added to replace
CONFIG_THERMAL with CPTCFG_ATH12K_THERMAL so the setting may be enabled
via menuconfig (as is done with ath10k and ath11k).
Note that at this stage, throttling has not been implemented upstream,
hence the slight change in wording versus existing options.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1
Link: https://patch.msgid.link/20260223132622.43464-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22280
Signed-off-by: Robert Marko <robimarko@gmail.com>
22fb70661799 fix flex array not at end of struct
6a5c4716ca25 convert memcpy + ETH_GSTRING_LEN to ethtool_puts
Signed-off-by: Robert Marko <robimarko@gmail.com>
a52cdb354d13 dns: validate IPv4 record addresses
b798c24205b5 dns: validate IPv6 record addresses
a3dcb4adc635 dns: validate reverse dns query name lengths
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This commit adds support for Gemtek (Centurylink/Lumen/Quantum Fiber)
W1700K.
Device specification
--------------------
SoC Type: Airoha AN7581
RAM: ESMT M16U8G16512A (2GB)
Flash: Winbond 25N04KVZEIR (512MB)
Ethernet: 2x gigabit via AN7581, 2x 10g via RTL8261N
Wi-Fi: MT7996 - BE19000
LEDs: 1 LED, power/status
Button: Reset
USB ports: None
Bootloader: U-Boot 2014.04-rc1 (Jun 12 2024 - 08:14:34) AXON 2.0
Fan: 1x controlled by Nuvoton NCT7511Y
This device is pretty useless with the stock firmware as it requires an
account to completely set it up. Additionally, the vendor bootloader is
signed and uses Airoha/Mediatek's BBT/BMT for bad block management on
the flash. It does not support UBI, thus kernel updates are subject to
BMT/BBT which OpenWrt does not support. In turn, if a kernel update
happens and a block is marked bad in the process, the device will fail
to boot and will need to be recovered via serial.
The workaround is to chainload U-Boot in place of the kernel, as it
should not need frequent updates and thus should not cause BBT/BMT to
misbehave and soft-brick the device. Upstream U-Boot supports loading
a FIT image from UBI, so we create a UBI partition for the new u-boot
env, FIT image and factory data. This way, bad blocks are managed by UBI
instead, which will not soft-brick the device should a block be marked
bad during a normal OpenWrt update. Users wishing to update U-Boot can
do so, but should be prepared to recover if a block goes bad.
Because the device is not useful with stock firmware, this is a one-way
ticket for most users and reverting will not be documented.
The following steps can be used to install OpenWrt on the W1700K.
Connect to serial console. There is a Torx T10 screw underneath the QR
code printed onto the label. Then, pry between the gray and white
plastic, starting by the ports on the back. There are clips arount the
entire device. Starting closest to the screw next to the UART header,
TX - GND - VCC - N/A - RX. The bootloader can be interrupted by
pressing any key.
Configuring Vendor Bootloader and Installing U-Boot Chainloader:
The bootloader's default bootcmd will only run a signed image. However,
we can still bootm our own image from flash.
NOTE: The vendor's ethernet drivers are flaky. You may have to reboot
and try the tftpboot part several times for it to work.
- setenv one flash read 0x600000 0x1000000 \$loadaddr
- setenv two "; bootm"
- setenv bootcmd "$one$two"
- setenv one
- setenv two
- saveenv
- setenv serverip 192.168.1.10; setenv ipaddr 192.168.1.1; tftpboot
0x89000000 openwrt-airoha-an7581-gemtek_w1700k-ubi-chainload-uboot.itb
- flash erase 0x600000 0x100000
- flash write 0x600000 0x100000 0x89000000
- reset
The device will now reboot into the U-Boot chainloader.
Loading the W1700K UBI Installer:
The installer can be downloaded at
https://github.com/hurrian/w1700k-ubi-installer/releases
- Boot the installer via the TFTP option in the U-Boot menu. This
process is automatic, though you may be prompted to answer some
questions.
- Once it is done, you may upgrade to your preferred build.
- For more information: https://github.com/hurrian/w1700k-ubi-installer
For those wishing to explore the stock firmware:
Rooting Stock FW (for making backups, recommended):
- Boot the router and watch serial console until presented with failsafe
mode. Enter it (f + enter).
- mount_root
- Change the root password (passwd).
- Open /etc/config/axon_platform_manager and set sshServerEnable,
localAccessEnable and remoteAccessEnable to 1.
- Search for "SSH". You'll find a long string with 3 matches such as
Enabled%25252c1%25252cSSH%Drop. Change any instances of "Disabled"
preceding SSH to "Enabled" and any instances of "Drop" to "Accept"
that follow SSH. Same for "Local SSH" and "Remote SSH".
- Set /etc/config/dropbear to:
config dropbear
option PasswordAuth 'on'
option RootPasswordAuth 'on'
option Port '22'
- Reboot.
- Connect 10g WAN port to existing network and SSH in with the password
you set.
- SSH into rooted stock fw.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17869
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When the virtual package "uci-firewall" is installed, the choice
between "firewall" and "firewall4" is arbitrary, sometimes resulting
in one, sometimes the other.
Set the default variant on "firewall4" to make it the preferred
package when installed as a dependency.
Link: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/1126
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22328
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of directing users to the useless 'man 8 apk', we direct
them to the wiki help page.
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22271
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow reinstalling already-installed packages without a version change.
Only the named packages are reinstalled, not their dependencies.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware
========
SoC: Qualcomm IPQ4018
ETH: Qualcomm QCA8075 (2 x RJ-45)
WDG: OnSemi SCT706
RAM: Micron MT41K128M16JT-125 (256MB)
NOR: Infineon S25FL512S (64MB)
Installation
============
1. Create a ramboot-able image with the command
{ dd if=/dev/zero bs=32 count=1 2>/dev/null; \
cat openwrt-ipq40xx-generic-huawei_ap4050dn-initramfs-uImage.itb; \
} > ramboot.bin`
2. Start a TFTP server in the folder with the ramboot.bin.
3. Plug in a USB-RJ45 serial adapter to the CONSOLE port of the device
and start a serial console session with
9600 baud, no parity, 1 stop bit.
4. Plug in either 12V power or PoE to the device.
5. On the prompt `Press f or F to stop Auto-Boot in 3 seconds`,
press `f` to enter the Huawei U-Boot command line
6. Enter a new password for the u-boot command line
7. In the command line, run these commands to ramboot OpenWrt:
setenv serverip <IPv4 address of TFTP server>
setenv ipaddr <IPv4 address for this AP>
setenv rambootfile ramboot.bin
run ramboot
8. In OpenWrt, set up the network and then `scp` the files
`u-boot-huawei_ap4050dn/uImage` and
`openwrt-ipq40xx-generic-huawei_ap4050dn-squashfs-sysupgrade.bin`
into `/tmp/`
9. To backup the original firmware, run the following:
cat /dev/mtd12 /dev/mtd13 > huawei_ap4050dn_fw_backup.bin.bin
10. Run the following commands to flash u-boot and OpenWrt to the device:
mtd erase uboot
mtd write /tmp/uImage uboot
sysupgrade -n /tmp/openwrt-ipq40xx-generic-huawei_ap4050dn-squashfs-sysupgrade.bin
11. The device should now boot OpenWrt! (sometimes the boot process takes a bit
longer due to the watchdog resetting the device before the watchdog driver runs)
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Add support for the Huawei AP4050DN. Due to vendor bootloader size
limitations, we require a second-stage U-Boot.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
memcpy() with overlapping src and dest buffers is an undefined behavior
in C. In the current code, a ConfRej response is generated by copying
input data in-place, where the dest address is lower than the src.
This happens to work in practice because memcpy() forward-copies data,
matching the behavior of memmove() in this case.
However, if FORTIFY_SOURCE or Address Sanitizer is enabled, memcpy()
will detect the overlap at run time and abort the program.
Replace the memcpy() with memmove() to ensure a well-defined behavior.
Reported-by: Filippo Carletti <filippo.carletti@gmail.com>
MRU patch https://github.com/ppp-project/ppp/pull/573
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22286
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Embed gpio_led struct in ath_led. Simpler Allocation.
Use a flex array for the name. Allows using a single allocation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21933
Signed-off-by: Robert Marko <robimarko@gmail.com>
ath79 at this point supports no ath5k devices.
The only targets with ath5k usage are bcm47xx, ixp4xx, and lantiq.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19848
Signed-off-by: Robert Marko <robimarko@gmail.com>
The single user of the downstream gpio-cascade driver has been switched
to use the upstream gpio-line-mux driver. Thus, we can drop the former
now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the GPIO line mux driver as a kernel module for selected usage by
devices.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Richtek RTQ6056 Current and Power Monitor ADC.
RTQ6056 is a high accuracy current-sense monitor with I2C and SMBus
compatible interface, and the device provides full information for
system by reading out the load current and power.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add a label to the spi node to allow device trees to reference it
(i.e. to mark status = "okay").
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/22151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Due to issues surrounding the implementation of the vendor BMT/BBT
on Airoha, upstream ATF + uboot has switched to UBI flash partitions.
However, some devices shipped on this platform are bootloader locked,
and thus it is impossible to replace ATF + uboot.
During testing for the Gemtek W1700K (#17869), sysupgrades from Linux
(which is unaware of the underlying BMT/BBT) would occasionally write
data into blocks which were remapped by the vendor uboot when it was
read on the following reboot, causing a soft brick.
An acceptable workaround [1],[2] was discussed where an intermediate
uboot would be written by the vendor uboot (which is aware of Airoha
BMT/BBT). This chainloader would then ignore the regions of flash
used by the vendor uboot, and store all relevant data inside of UBI.
UBI would then be used to handle bad block management. As the vendor
ATF + uboot do not read or interact with the UBI region, we would avoid
unwanted remaps from BMT/BBT.
This commit introduces support for building such a chainloader, by
packaging u-boot and DTS into a FIT image; to be flashed like a kernel.
Configuration for the Gemtek W1700K is provided as an example of how the
chainloader is used.
[1] https://github.com/openwrt/openwrt/pull/17869#discussion_r2836066746
[2] https://github.com/openwrt/openwrt/pull/17869#discussion_r2838395671
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
[ move FIP_COMPRESS to Build/Compile, wrap some long lines ]
Link: https://github.com/openwrt/openwrt/pull/22151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It is more accurate to describe the contents of the FIP as
compressed, instead of the FIP itself becoming compressed.
Update variable naming accordingly.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/22151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
OpenWrt issue:
https://github.com/openwrt/openwrt/issues/16183
Problem summary:
On qualcommax (ipq60xx/ipq807x) with ath11k, monitor-mode captures contain
frames that are consistently longer than expected by 8 bytes.
The symptom is visible in pcap/radiotap captures, and Wireshark parsing
becomes correct after manually cutting these 8 bytes from captured frames.
This patch:
- Remove merge-stage FCS/tail manipulations in ath11k_dp_rx_mon_merg_msdus().
- add length fix in ath11k_dp_rx_mon_deliver(), trim 8 bytes right
before radiotap update and delivery to mac80211.
This targets monitor capture length correctness only and keeps the fix scoped
to the monitor RX delivery path.
Tested-on: ipq8072 yuncore,ax880; ipq6018 yuncore,ax840; yuncore,fap650
Signed-off-by: Ruslan Isaev <legale.legale@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22244
Signed-off-by: Robert Marko <robimarko@gmail.com>
Port drivers for the hardware true random number generator found in
MediaTek SoCs and enable them for all boards.
This has the side-effect of U-Boot now providing '/chosen/kaslr-seed'
to Linux which is required to enabled KASLR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for Airoha EN7581/AN7583 NPU variant firmware present in
linux-firmware. The Airoha EN7581 NPU variant is to support devices
equipped with the MT7996 WiFi chip.
While at it also add an extra new line to follow pattern of double new line to
separate each firmware package.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The fs_wait_for_key function runs multiple background processes that all
try to delete the same temporary file ($keypress_wait) when they exit.
This creates a race condition where one process successfully deletes the
file while others fail with ENOENT.
Busybox rm only suppresses "file not found" errors during the initial lstat()
check, not during the actual unlink() call. This causes error messages in the
boot log even with rm -f:
rm: can't remove '/tmp/tmp.hKjPDH': No such file or directory
Fixed by redirecting stderr to /dev/null for rm calls in concurrent contexts.
This change does not affect functionality and only avoids confusing log
output during boot.
Signed-off-by: Oliver Sedlbauer <os@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/22079
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Several OpenWrt-related fixes are included in this release.
Drop upstreamed patches and refresh the rest.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Link: https://github.com/openwrt/openwrt/pull/22240
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXqmiX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXmbimX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
The &pointer + 1 trick is a C89 trick to point to area allocated after
the size of the struct. We have struct_size and flex arrays now.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22170
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit c053b22573.
KSZ DSA driver is the only thing in the kernel selecting DCB support
instead of depending on it if required.
So, it will enable DCB support without asking and we do not want the
kernel size increase, as well as current Layerscape ARMv8 build failure.
So, revert this until its fixed upstream or worked around.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This access point is a ‘friend’ of the T56 supplied by Odido but with DDR3 RAM and with two Ethernet 2.5 (GPY211)
The flash procedure is similar to other Zyxel T56/EX5600/EX5601
If you need backup please use the T56 guide
Please refer to https://openwrt.org/inbox/toh/zyxel/wx5600-t0 for detailed flash informations
Specifications:
SOC: MT7986b
RAM: 512MB
Flash: 512 MB SPI NAND
Ports: 2 LAN 2.5Gbps (GPY211C)
WIFI: MT7976GN + MT7976AN
LED: 3 bicolor LED - 1 monocolor LED
Buttons: Reset and WPS
We can install all with U-boot and mtk_uartboot.
Load Uboot:
```
./mtk_uartboot -a -p ./mt7986-ram-ddr3-bl2.bin -s /dev/ttyUSB0 -f openwrt-mediatek-filogic-zyxel_wx5600-t0-ubootmod-bl31-uboot.fip
```
**WARNING: Please use a GBIT ethernet or force it on system**
**WARNING: Please use only LAN2 port in Uboot**
Press 0 on Bootmenu
```
mtd erase ubi
run ubi_format
bootmenu
```
Load and write BL2 and U-boot:
```
8
7
```
Load and write recovery and production
```
6
5
```
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Co-authored-by: Hal Martin <halmartin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18364
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This access point is a ‘friend’ of the T56 supplied by Odido but with DDR3 RAM and with two Ethernet 2.5 (GPY211)
The flash procedure is similar to other Zyxel T56/EX5600/EX5601
If you need backup please use the T56 guide
Please refer to https://openwrt.org/inbox/toh/zyxel/wx5600-t0 for detailed flash informations
We can install all with U-boot and mtk_uartboot.
Load Uboot:
```
./mtk_uartboot -a -p ./mt7986-ram-ddr3-bl2.bin -s /dev/ttyUSB0 -f openwrt-mediatek-filogic-zyxel_wx5600-t0-ubootmod-bl31-uboot.fip
```
**WARNING: Please use a GBIT ethernet or force it on system**
**WARNING: Please use only LAN2 port in Uboot**
Press 0 on Bootmenu
```
mtd erase ubi
run ubi_format
bootmenu
```
Load and write BL2 and U-boot:
```
8
7
```
Load and write recovery and production
```
6
5
```
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Link: https://github.com/openwrt/openwrt/pull/18364
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add menuconfig options to include modules for (virtio) vsockets. These are
used when running as Guest OS in a VM.
OpenWRT can be run in a vm (mostly commonly on the x86/64 and armsr
targets). Often it is convenient to have some sort of guest agent running,
to ease communication from host to guest.
Virtual Sockets provide this communication channel.
Virtio is a transport for this communication channel.
Virtual Sockets over virtio are for example used by Incus.
Virtual Sockets in general are used by most hypervisors, including VMware,
Hyper-V, and libvirt (qemu). These may need other transport-specific
modules not included in this commit.
Signed-off-by: Mathijs Rietbergen <mathijs.rietbergen@proton.me>
There are a number of pse chips already present in upstream Linux.
OpenWrt is starting to support a number of devices can contain various pse
chips. But having all the pse chip combinations defined at the target
level will result in bloat on images.
Present the current upstream Linux pse drivers as packages so that they
can be selectively included per board (rather than per target).
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
[Make it depend on REGULATOR_SUPPORT, and !SMALL_FLASH]
Link: https://github.com/openwrt/openwrt/pull/22172
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bump uboot-stm32 to upstream release 2026.01.
Two upstream patches were backported to resolve silent crash on
STM32MP135F-DK board.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/21965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
