This adds support for the Kontron i.MX8MP OSM-S size system-on-module +
eval board.
CPU: NXP i.MX8MP @ 1600MHz (quad-core A53)
Memory: 4 (up to 8) GByte LPDDR4-RAM
Storage: 32 (up to 128) GByte eMMC + microSD slot
Ethernet: 2x 1 Gbit/s IEEE (1x with TSN)
UART: 1x UART console output on the Mini-B USB Debug Port
(signals are really UART on this Mini-B USB port!!!, there is
an adapter with ftdi available from Kontron)
1x RS232, 1x RS485
USB: 2x USB 2.0 Type-A, 1x USB 3.0 Type-C DRP
Misc: 8 (up to 128) kByte EEPROM (at24), RTC, 2x CAN, HDMI, 1x PCIe
This will create an SD card image for the board.
To use this image you have to bring the board to the recovery boot mode
(normal boot mode is eMMC). At the time of writing, the SoM (or the SoC)
has a bug that the FORCE_RECOVERY signal (switch S1 on the eval board)
doesn't work as long as the eMMC boot0 partition contains data.
Therefore you have to wipe this boot0 partition to be able to boot from
SD card. To do this call the following commands at uboot:
mmc dev 0 1
mmc erase 0 0x2000
After that, the system will try to boot from SD card.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add some additional Gateworks Venice boards to sysupgrade support.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/22202
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add network config for single-port Gateworks venice boards such that the
ethernet port is the WAN port instead of the default being a LAN port.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/18629
Signed-off-by: Robert Marko <robimarko@gmail.com>
The upstream device-tree files are now using 'gateworks' instead of 'gw'
for compatible. Add this pattern so that the newer boards support
sysupgrade.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17964
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The GW82xx-2x has two network ports. By convention, the first
port (eth0) should be the WAN port and the second port (eth1)
should be the LAN port.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17717
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GW74xx's first RJ45 is eth0 which should be the WAN adapter, not
eth1 which is the CPU uplink port to the switch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/15736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Gateworks Venice imx8m family of boards:
- required kernel modules for on-board devices
- image generation
- initial network config
- sysupgrade support
The resulting compressed disk image
(bin/targets/imx/cortexa53/openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz)
can be installed on a Gateworks venice board via U-Boot:
u-boot=> tftpboot $loadaddr openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz && \
gzwrite mmc $dev $loadaddr $filesize
WARNING: this will overwrite any boot firmware on the eMMC user hardware
partition which if being used will brick your board requiring JTAG to
re-program boot firmware and recover
The compressed disk image contains the partition table and filesystems only
and that it is expected that boot firmware is installed properly on the
eMMC boot0 hardware partition. The easiest way to ensure this is to
use the Gateworks JTAG adapter/process to install the latest boot firmware
as follows from a Linux host:
wget http://dev.gateworks.com/jtag/jtag_usbv4
chmod +x jtag_usbv4
wget http://dev.gateworks.com/venice/images/firmware-venice-imx8mm.bin
sudo ./jtag_usbv4 -p firmware-venice-imx8mm.bin
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
