Currently, Ralink SoCs use the default ARCH_DMA_MINALIGN value of 128
bytes defined in mach-generic. This is excessive for these platforms
and leads to significant memory waste in kmalloc.
Override ARCH_DMA_MINALIGN to use L1_CACHE_BYTES, which is 16 bytes for
RT288X and 32 bytes for other Ralink SoCs.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23314
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix typo in backup partition offset: `0xfe000` should be `0xfe0000`.
The incorrect offset caused the partition to be mapped at `0x0fe000`
instead of `0xfe0000`, placing it inside the firmware partition range.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23511
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 8 MiB NOR
- RAM: 64 MiB DDR2
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN, 3x 10/100 LAN (MT7628)
- Buttons: 1x Reset, 1x wps
- LEDs: Front: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 12v barrel
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN/WAN | d4:0d:ab:xx:xx:x0 | label |
| WLAN 2g | d4:0d:ab:xx:xx:x1 | label+1 |
+---------+-------------------+-----------+
Migration to OpenWrt:
- Download the RSA-signed intermediate firmware from the Cudy website: `openwrt-ramips-mt76x8-cudy_wr300-squashfs-flash.bin`
- Connect the computer to the LAN and flash the intermediate firmware via the OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as `recovery.bin` in the TFTP server
- Power on the device and hold the reset button immediately after the first LED blink
- The recovery process will start
- When the recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load an initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23426
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
nvmem-layout is used instead of the older nvmem-cells. Seems to be a
copy/paste mistake.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23512
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The gmac1 is not used and doesn't have any mac address configured. The
gmac0 has the nvmem-cells set and can actually be used to retrieve the
correct mac address.
Fixes: c7c54f3134 ("ramips: add support for Plasma Cloud PAX1800-Lite")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/23441
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specificaitons:
- MediaTek MT7621AT SoC
- 256 MB RAM
- 16MB SPI NOR Flash
- 256MB NAND (split in half for firmware fallback)
- 4x 10/100/1000 Mbps Ethernet, with passive PoE support on LAN1
- WLAN : MediaTek dual-band WiFi 5
- 2.4 GHz : b/g/n, MIMO 2x2
- 5 GHz : n/ac, MIMO 2x2
- Quectel EG060K-EA 4G CAT6 modem
- 2.0 USB Type-A HOST port
- 1x Digital input
- 1x Digital output
- 2x SIM slot (can be swapped via GPIO)
GPIO:
- 1 button (Reset)
- 14 LEDs (power, 4x WAN status, Wifi 2G, Wifi 5G, 3G, 4G, 5x RSSI)
- 3 Modem control (power button, reset, sim select)
- 1 Digital input
- 1 Digital output
Installation
------------
Notice: update OEM firmware to 7.19 or later, earlier versions will
fail to flash openwrt factory firmware.
1. Check from which partition the device is currently running from
$ cat /proc/bootconfig/chosen
In case this output reads rutos-b, install a software update from
Teltonika first. After upgrade completion, check this file now reads
rutos-a before continuing.
2. Download the *-squashfs-factory.bin firmware image
3. Flash firmware image via WEB interface
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile connection:
- EG060K-EA:
Execute AT commands:
echo -ne 'AT+QCFG="usbnet",2\r\n' > /dev/ttyUSB2
echo -ne 'AT+CFUN=1,1\r\n' > /dev/ttyUSB2
Use ModemManager to establish mobile connection.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Specifications:
- MediaTek MT7621AT SoC
- 256 MB RAM
- 16MB SPI NOR Flash
- 256MB NAND (split in half for firmware fallback)
- 2x 10/100/1000 Mbps Ethernet, with passive PoE support on LAN
- WLAN : MediaTek dual-band WiFi 5
- 2.4 GHz : b/g/n, MIMO 2x2
- 5 GHz : n/ac, MIMO 2x2
- Quectel RG520N-EB 5G R16 modem (RUTM30) or RG500U-EB 5G (RUTM31)
- 1x Digital input
- 1x Digital output
- 2x SIM slot (can be swapped via AT commands)
- eSIM
- TPM
GPIO:
- 1 button (Reset)
- 3 LEDs (power, 2 RGB)
- 3 Modem control (power button, reset, eSIM switch)
- 1 Digital input
- 1 Digital output
- 1 TPM enable
Installation
------------
Notice: update OEM firmware to 7.19 or later, earlier versions will
fail to flash openwrt factory firmware.
1. Check from which partition the device is currently running from
$ cat /proc/bootconfig/chosen
In case this output reads rutos-b, install a software update from
Teltonika first. After upgrade completion, check this file now reads
rutos-a before continuing.
2. Download the *-squashfs-factory.bin firmware image
3. Flash firmware image via WEB interface
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile connection:
- RG520N-EB:
Use "ModemManager" to establish mobile data connection.
- RG500U-EB:
echo -ne 'AT+QNETDEVCTL=1,3,1\r\n' > /dev/ttyUSB2
Create DHCP interface with usb0 device.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Specifications:
- MediaTek MT7621AT SoC
- 256 MB RAM
- 16MB SPI NOR Flash
- 256MB NAND (split in half for firmware fallback)
- 5x 10/100/1000 Mbps Ethernet, with passive PoE support on LAN1
- WLAN : MediaTek dual-band WiFi 5
- 2.4 GHz : b/g/n, MIMO 2x2
- 5 GHz : n/ac, MIMO 2x2
- Quectel RG520N-NA 5G R16 modem (RUTM50) or RG500U-EB 5G (RUTM51)
- 2.0 USB Type-A HOST port
- 1x Digital input
- 1x Digital output
- 2x SIM slot (can be swapped via AT commands)
GPIO:
- 1 button (Reset)
- 13 LEDs (power, 4x WAN status, Wifi 2G, Wifi 5G, 3G, 4G, 5G, RSSI
1,2,3)
- 2 Modem control (power button, reset)
- 1 Digital input
- 1 Digital output
Installation
------------
Notice: update OEM firmware to 7.19 or later, earlier versions will
fail to flash openwrt factory firmware.
1. Check from which partition the device is currently running from
$ cat /proc/bootconfig/chosen
In case this output reads rutos-b, install a software update from
Teltonika first. After upgrade completion, check this file now reads
rutos-a before continuing.
2. Download the *-squashfs-factory.bin firmware image
3. Flash firmware image via WEB interface
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile connection:
- RG520N-NA:
Use "ModemManager" to establish mobile data connection.
- RG500U-EB:
echo -ne 'AT+QNETDEVCTL=1,3,1\r\n' > /dev/ttyUSB2
Create DHCP interface with usb0 device.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
The RG-EW1300G is a router with 1 x WAN and 3 x LAN gigabit ports.
The router runs on Ruijie OS by default.
- Specifications:
* SoC: MT7621A
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* WiFi0: Mediatek MT7615 2.4GHz 802.11b/g/n
* WiFi1: Mediatek MT7615 5GHz 802.11ac
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console - As marked on PCB, baudrate is 57600. DO NOT CONNECT 3.3V.
* Buttons: Reset, WPS.
* LED: Programmable LEDs via GPIO working for Red+Green status, and Mesh/WPS at the rear of the chassis.
- Default Flash:
```
GD25Q128C(c8 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
6 cmdlinepart partitions found on MTD device raspi
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000050000 : "u-boot"
0x000000050000-0x000000060000 : "u-boot-env"
0x000000060000-0x000000070000 : "Factory"
0x000000070000-0x000000080000 : "product_info"
0x000000080000-0x000000090000 : "kdump"
0x000000090000-0x000001000000 : "firmware"
0x00000031a847-0x000001000000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs_data" created automatically, ofs=0xae0000, len=0x520000
0x000000ae0000-0x000001000000 : "rootfs_data"
register mt_drv
```
```
cat /proc/mtd
dev: size erasesize name
mtd0: 00050000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "factory"
mtd3: 00010000 00010000 "product_info"
mtd4: 00010000 00010000 "kdump"
mtd5: 00f70000 00010000 "firmware"
mtd6: 0028a847 00010000 "kernel"
mtd7: 00ce57b9 00010000 "rootfs"
mtd8: 00520000 00010000 "rootfs_data"
```
- Installation:
1. Open the case, solder to the marked 4 pin header
2. Connect it to a USB-UART TTL (do not connect to 3.3v)
3. Open a terminal with baud 57600.
4. Power on device, and repeatedly press "2" key to catch bootloader option
5. Set IP, TFTP server IP, and image file to load (eg, openwrt-ramips-mt7621-ruijie_rg-ew1300g-v1-squashfs-sysupgrade.bin)
6. System will reboot into OpenWRT.
Signed-off-by: Matt Brent <git@mattzfiber.co.za>
Link: https://github.com/openwrt/openwrt/pull/21864
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a nonsensical binding that's not implemented anywhere.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23137
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 15887235c1 ("generic: mtk_eth_soc: reduce driver memory usage")
allows building mediatek ethernet driver without CONFIG_PAGE_POOL_STATS.
This can slightly improve throughput on legacy MIPS based MT7621 SoC.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/23142
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop patches and configs for Linux 6.12.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22871
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to Linux kernel version 6.18.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22871
Signed-off-by: Nick Hainke <vincent@systemli.org>
Specification:
* CPU: MediaTek MT7628AN (580 MHz)
* Flash: GigaDevice GD25Q128CSIG (16 MiB)
* RAM: Winbond W9751G6KB-25 (64 MiB)
WikiDevi page: <https://wikidevi.wi-cat.ru/Keenetic_City_(KN-1510)>
How to flash:
* Configure TFTP server with IP address 192.168.1.2/24
* Serve OpenWrt factory image as "KN-1510_recovery.bin"
* Connect the PC to router's LAN port, hold the reset button and power
the router up. When the power LED starts blinking release the
button.
The same instructions apply to OEM firmware, except one can take it
from osvault.keenetic.net
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/22404
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EDUP EP-RT2983 comes with a factory installed version of OpenWrt 23.05
with device name "netis,n6".
Specification
--------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (Toshiba)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x WiFi (green)
1x Mesh/WPS (green); flashing green during boot
3x LAN (green)
1x WAN (green); flashing red during upgrade and failsafe
- Power : 12 VDC 1A
Installation
-------------
1. Log in to LuCI
2. Go to System, Backup / Flash Firmware
3. If desired, backup the current system by saving (all) the mtdblock
contents.
4. Flash new firmware image, select Flash image.
5. Browse and select the sysupgrade file
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-sysupgrade.bin"
and then Upload.
6. Unselect "Keep settings and retain the current configuration"
Note: All settings will be reset to default. WiFi is not enabled by
default so a connection via Ethernet is necessary to log in and set up.
7. Allow "Force upgrade" (tick the box if there is one), or press Continue
if there is no box to tick. This is because the name is now
"edup,ep-rt2983" as it should have been from the start.
8. Proceed to flash. Wait for reboot and keep power connected.
9. After reboot, default address to access LuCI is 192.168.1.1 with
no password
Recovery (UART)
----------------
1. Remove the 4 screws on the bottom and pry open the cover.
2. Connect serial adapter to the unpopulated serial header pins
TX, RX, GND near the WPS button. Do not connect VCC.
3. Start serial terminal (e.g. minicom, screen, etc) on the computer and
turn on the router.
4. As prompted, hit any key to stop autoboot.
5. Enter 2 to select "2. Upgrade firmware"
6. Enter 0 to select "0 - TFTP client (Default)"
7. Accept the defaults by pressing Enter for
"Input U-Boot's IP address: 192.168.1.1",
"TFTP server's IP address: 192.168.1.2",
"Input IP netmask: 255.255.255.0"
8. Assign your PC's Ethernet port a static IP 192.168.1.2 with netmask
255.255.255.0 and connect to a LAN port on the router using the
Ethernet cable. Disconnect all other network connections (e.g. WiFi) on
the computer.
9. Serve the factory image
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-factory.bin" using
a TFTP server, e.g. tftpd64. For convenience, the filename can be renamed
to something shorter.
10. In the serial terminal, when prompted "Input file name:", enter the
filename from the previous step and press Enter.
11. The factory image will be flashed as indicated. Wait for reboot.
MAC addresses prototype
------------------------
+---------+---------------------+
| | MAC example |
+---------+---------------------+
| LAN | CC:D8:1F:47:xx:yy |
| WAN | CC:D8:1F:47:xx:yy+1 |
| WLAN 2G | CC:D8:1F:17:xx:yy+2 |
| WLAN 5G | CC:D8:1F:77:xx:yy+2 |
+---------+---------------------+
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Restore CONFIG_PAGE_BLOCK_MAX_ORDER=10 in ramips 6.18 config fragments
to fix build failures where PAGE_BLOCK_MAX_ORDER was undefined.
Support for Linux 6.18 on ramips was added after this OpenWrt change:
ac0cb87a45.
Before that integration, the kernel option CONFIG_PAGE_BLOCK_MAX_ORDER=10
was provided in target/linux/generic/config-6.18 and applied broadly.
After the ramips 6.18 integration the generic fragment no longer supplied
this option for ramips targets, which caused some backported code paths
and drivers to assume PAGE_BLOCK_MAX_ORDER was defined and led
to compilation failures.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22831
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ramips now supports 6.18 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MODULE_DEVICE_TABLE macro was using an incorrect parameter 'match'
instead of the actual device table name 'mt7621_nfc_id_table'.
This fixes the reference to use the correct symbol name, ensuring
proper device table registration for module autoloading.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix fe_clean_rx to handle the changed frag_cache layout on newer kernels.
For kernels >= 6.13 the fragment cache needs to be converted from its
encoded_page value instead of using the old va field. Add an ifdef
to use frag_cache.encoded_page & PAGE_MASK and virt_to_page for those
kernels, keep the old path for older kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refreshed patches for ramips/patches-6.18 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace previous bgpio_init usage with a full gpio_chip registration so the driver
integrates cleanly with the kernel GPIO core.
Add drivers/gpio/gpio-ralink.c implementing a gpio_chip with:
- get/set, direction_input/direction_output, get_direction
- get_multiple/set_multiple to support efficient multi-bit ops
- DT handling for determining ngpios (reads "ngpios" or falls back to gpio-ranges)
- MAX_NGPIOS cap and safe defaults
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update patch 831-03-mmc-mtk-sd-use-default-PATCH_BIT1-2-values-for-mt762.patch
to a newer version compatible with kernel 6.18.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove symbols no longer present in version 6.18,
add new 6.18 kernel symbols.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
This symbol is selected by CONFIG_BPF, which was already enabled
on generic config-6.12.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the Wavlink "Halo Base Pro".
SOC: MT7621DAT
RAM: 128MiB
Flash: 16MiB NOR
WiFi: MT7603EN + MT7613BEN
Buttons:
- The touch sensor was originally for WPS, but this has been moved to the
pair button which is no longer used to prevent accidental touches
LEDs:
- On original firmware, the status LEDs light up as follows:
- Purple = booting, Blue = working, Red = error
Partitions:
- factory contains unique WiFi EEPROM and default MAC addresses
- vendor partition has an unknown purpose
Stock MAC address allocation:
- LAN1: xx:xx:xx:xx:xx:80
- LAN2/WAN: xx:xx:xx:xx:xx:81
- WiFi 2.4G: xx:xx:xx:xx:xx:82
- WiFi 5G: xx:xx:xx:xx:xx:83
LAN Ports:
- lan1 is the normal white LAN port
- lan2 is labelled "LAN/Backhaul", which can either be LAN or WAN.
- Since this device is intended to be part of a mesh, this will usually
be a LAN port, hence why it's assigned to lan2 here
Notes:
- I've chosen "Halo Base Pro" as the device model, despite the website URL
showing WL-WN535M3, as the label only states "Halo Base Pro".
- Only the 5GHz WiFi address is labelled on the device
Signed-off-by: William Latter <williamlatter77@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22400
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compared to the "mediatek,mt8173-xhci", this is a more generic and
reasonable compatible string. On the driver side, they are identical.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The USB t-phy driver includes some magic register init values. This
should be beneficial for the USB stability and performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MT7621 USB phys are compatible with the MediaTek T-PHY controller.
The vendor SDK also enabled this driver for MT7621.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit a2fa1db797.
These patches stop secondary CPUs before restart and wait for them
to go offline, fixing the mt7621 reboot deadlock without needing to
disable CONFIG_LIST_HARDENED.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/22724
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Z-ROUTER ZR-2662 (also known as Routerich
AX1800 V2) wireless WiFi 6 router.
Hardware specification
---------------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Note: This device is similar to Z-ROUTER ZR-2660, but with minor hardware
revisions. The firmware and configuration are compatible.
Signed-off-by: xingchi <juncaixingchi2026@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21524
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB NOR
- RAM: 64 MiB DDR2
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN/LAN, 1x 10/100 LAN (MT7628)
- Build-in LTE Modem: MeigLink SLM770A
4G Cat. 4 (150/50 Mbps)
- Buttons: 1x Reset, 1x wps
- LEDs: Front: 1x Red, 1x White,
Back: 3x White 4G signal strengh
- Serial console: unpopulated header, 115200 8n1
- Power: USB-C
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Migration to OpenWrt:
- Download the RSA signed intermediate firmware from the Cudy website:
`openwrt-ramips-mt76x8-cudy_lt300-v3-squashfs-flash.bin`
- Connect computer to LAN and flash the intermediate firmware via OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The dt-bindings suggest using "^serial(@.*)?$" as the node name.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is necessary to make it work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
<>, <> is the preferred way to specify multiple entries.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22736
Signed-off-by: Robert Marko <robimarko@gmail.com>
