This commit fixes stability issues on certain RAX3000Me devices. Some
devices has DDR3 RAM which don't able to work reliably at 2133 MHz
and require special BL2 (1866 MHz RAM freq).
Fixes: https://github.com/openwrt/openwrt/issues/20046
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new profiles are intended for devices with DDR3 RAM which
don't able to work reliably at 2133 MHz.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit add kernel module support for Infineon DPS310/DPS368/DPS422
digital barometric air pressure and temperature sensor.
Test on custom board based on Mediatek MT7988a.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20101
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make sure that the package gets updated after the last fix.
Fixes: cd20ae44f2 ("uqmi: fix data-format parsing")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
wda-get-data-format now returns an object instead of a single string.
Account for this change when reading the packet data format.
Suggested-by: Sebastian Ertz (https://github.com/sebastianertz)
Signed-off-by: David Bauer <mail@david-bauer.net>
The EN751221 has an XHCI that is compatible with MT7621.
While there is setup logic in the vendor code for both
EN751221 and MT7621, but MT7621 does not use it in mainline
or OpenWRT, and it appears to work correctly with EN751221.
Include SCSI / Mass Storage because many EcoNet devices
contain a builtin USB SD-Card reader.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20050
[Remove usb storage kmod from smartfiber_xp8421-b]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New upstream release. Debian changelog:
* New upstream microcode datafile 20250812 (closes: #1110983, #1112168)
- Mitgations for INTEL-SA-01249 (processor Stream Cache):
CVE-2025-20109: Improper Isolation or Compartmentalization in the
stream cache mechanism for some Intel Processors may allow an
authenticated user to potentially enable escalation of privilege via
local access. Intel also disclosed that several processors models
had already received this mitigation on the previous microcode
release, 20250512.
- Mitigations for INTEL-SA-01308:
CVE-2025-22840: Sequence of processor instructions leads to
unexpected behavior for some Intel Xeon 6 Scalable processors may
allow an authenticated user to potentially enable escalation of
privilege via local access.
- Mitigations for INTEL-SA-01310 (OOBM services module):
CVE-2025-22839: Insufficient granularity of access control in the
OOB-MSM for some Intel Xeon 6 Scalable processors may allow a
privileged user to potentially enable escalation of privilege via
adjacent access.
- Mitigations for INTEL-SA-01311 (Intel TDX):
CVE-2025-22889: Improper handling of overlap between protected
memory ranges for some Intel Xeon 6 processors with Intel TDX may
allow a privileged user to potentially enable escalation of
privilege via local access.
- Mitigations for INTEL-SA-01313:
CVE-2025-20053: Improper buffer restrictions for some Intel Xeon
Processor firmware with SGX enabled may allow a privileged user to
potentially enable escalation of privilege via local access.
CVE-2025-21090: Missing reference to active allocated resource for
some Intel Xeon processors may allow an authenticated user to
potentially enable denial of service via local access.
CVE-2025-24305: Insufficient control flow management in the Alias
Checking Trusted Module (ACTM) firmware for some Intel Xeon
processors may allow a privileged user to potentially enable
escalation of privilege via local access.
- Mitigations for INTEL-SA-01367 (Intel SGX, TDX):
CVE-2025-26403: Out-of-bounds write in the memory subsystem for some
Intel Xeon 6 processors when using Intel SGX or Intel TDX may allow
a privileged user to potentially enable escalation of privilege via
local access.
CVE-2025-32086: Improperly implemented security check for standard
in the DDRIO configuration for some Intel Xeon 6 Processors when
using Intel SGX or Intel TDX may allow a privileged user to
potentially enable escalation of privilege via local access.
- Fixes for unspecified functional issues on several Intel Core and
Intel Xeon processor models.
* Updated microcodes:
sig 0x000606a6, pf_mask 0x87, 2025-03-11, rev 0xd000410, size 309248
sig 0x000606c1, pf_mask 0x10, 2025-03-06, rev 0x10002e0, size 301056
sig 0x000806f8, pf_mask 0x87, 2025-04-04, rev 0x2b000643, size 592896
sig 0x000806f7, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f6, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f5, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f4, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f8, pf_mask 0x10, 2025-04-08, rev 0x2c000401, size 625664
sig 0x000806f6, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000806f5, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000806f4, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000a06a4, pf_mask 0xe6, 2025-03-19, rev 0x0025, size 140288
sig 0x000a06d1, pf_mask 0x95, 2025-05-15, rev 0x10003d0, size 1667072
sig 0x000a06d1, pf_mask 0x20, 2025-05-15, rev 0xa000100, size 1638400
sig 0x000a06f3, pf_mask 0x01, 2025-05-03, rev 0x3000362, size 1530880
sig 0x000b06a2, pf_mask 0xe0, 2025-02-24, rev 0x4129, size 224256
sig 0x000b06a3, pf_mask 0xe0, 2025-02-24, rev 0x4129
sig 0x000b06a8, pf_mask 0xe0, 2025-02-24, rev 0x4129
sig 0x000b06d1, pf_mask 0x80, 2025-05-21, rev 0x0123, size 80896
sig 0x000c0662, pf_mask 0x82, 2025-05-14, rev 0x0119, size 90112
sig 0x000c06a2, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c0652, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c0664, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c06f2, pf_mask 0x87, 2025-04-15, rev 0x210002b3, size 564224
sig 0x000c06f1, pf_mask 0x87, 2025-04-15, rev 0x210002b3
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc (Intel N150 PC)
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20045
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds kernel packages for the Vitesse VSC73XX switches.
I have split the switch into explicit SPI and platform integrated
variants as it's quite a bit of code.
Link: https://github.com/openwrt/openwrt/pull/20057
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2ae08749a87e ucode: add padding to uc_resource_ext_t
7931bd901222 socket: add socket.pair()
4cd07cd66ab3 socket: add socket.open()
6350e6383ff3 struct: implement X and Z formats for hex and base64 coding
e632e6da1fbc vm: fix potential eyond end of array accesses
a7ead3169ebf resolv: properly handle multiple TXT strings
9d782ea4af63 math: Add an optional range to rand()
Fixes: https://github.com/jow-/ucode/issues/315
Fixes: https://github.com/jow-/ucode/issues/321
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2859741d971e dhcpv4: store reqopts as uint8_t
6d342cc03bf7 odhcpd: add DNR (RFC 9463) support
c89b8b3f2ff3 odhcpd: make the IPv6 RA DNR lifetime configurable
066b3dc6ec1a netlink: fix a memory leak
171140e90b6a odhcpd: add a helper function for addr6/prefix parsing
5585b969c18f router: move pref64 calculations to the config stage
4308384748be dhcpv6: add ipv6 pxe support
6e1ad492cef5 router: replace ssize_t with size_t
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20022
Signed-off-by: Robert Marko <robimarko@gmail.com>
Version 6.15 - 29-Aug-2025
* netlink: fix missing headers in text output
* netlink: fix print_string when the value is NULL
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20021
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PKG_MAKE_FLAGS is required when compiling r8168-rss
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20001
Signed-off-by: Robert Marko <robimarko@gmail.com>
While these boards have an at24 EEPROM for storing the MAC address,
early revisions (up until about 2017) did not contain actual addresses.
Create a random address to have ethernet function properly in u-boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The version of libxml2 was bumped from 2.13.6 to 2.14.5. Since version
2.14, libxml2 is not binary compatible with older versions. Therefore
add an abi version.
From the NEWS file:
Binary compatibility is restricted to versions 2.14 or newer. On ELF
systems, the soname was bumped from libxml2.so.2 to libxml2.so.16.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/19983
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gettext-full only provides libintl which is not licensed under
GPL-3.0.-or-later but under LGPL-2.1-or-later as stated in
gettext-runtime/intl/COPYING.LIB
Fixes: c10d97484a (Add more license tags with SPDX identifiers)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19943
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
elfutils libraries are not licensed under GPL-3.0-or-later, they are dual
licensed: GPL-2.0-or-later OR LGPL-3.0-or-later as clearly stated in
source files as well as on https://sourceware.org/elfutils:
The libraries and backends are dual GPLv2+/LGPLv3+. The utilities are GPLv3+.
Fixes: b98fb76646 (elfutils: import package from packages.git)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds ddr3 build for the ddr3 variant of the CMCC RAX3000Me
router.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Airoha AN8855 switch. Some CMCC RAX3000Me hw
revisions are shipped with Airoha switch.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa E52C is a compact network computer using the Rockchip RK3582
SoC.
- https://radxa.com/products/network-computer/e52c
Hardware
--------
- Dual Cortex-A76 and Quad Cortex-A55 CPU
- 5 TOPS NPU
- 2/4/8GB LPDDR4 RAM
- 16/32/64GB on-board eMMC
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB Type-C debug port
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5C (Lite) is a single board computer using the Rockchip
RK3588S2 (RK3582) SoC.
- https://radxa.com/products/rock5/5c
Hardware
--------
- Quad (Dual) Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU (5C only)
- 6 (5) TOPS NPU
- 1/2/4/8/16/32GB LPDDR4X RAM
- eMMC/SPI NOR flash connector
- microSD card slot
- Wi-Fi 6 (AIC8800D80, not yet supported)
- Gigabit Ethernet port with PoE (additional PoE HAT required)
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB 3.1 Gen1 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- FPC connector with PCIe 2.1 x1
- PWM fan connector
- 20x2 pin header
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5 ITX(+) is a Mini-ITX form factor computer using the
Rockchip RK3588 SoC.
- https://radxa.com/products/rock5/5itx
- https://radxa.com/products/rock5/5itxp
Hardware
--------
- Quad Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU
- 6 TOPS NPU
- 4/8/16/24/32GB LPDDR5 RAM
- on-board eMMC
- 16MB SPI NOR flash
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports with PoE (additional PoE module required)
- USB 3.1 Gen1 Type-C HOST/OTG port
- 4x USB 3.1 Gen1 Type-A HOST ports
- 2x USB 2.0 Type-A HOST ports
- M.2 M Key connector with PCIe 3.0 x2
- 4x SATA connectors (ITX only)
- 2nd M.2 M Key connector with PCIe 3.0 x2 (ITX+ only)
- M.2 E Key connector with PCIe 2.1 x1 and USB 2.0
- RTC battery socket for CR1220
- 4pin PWM fan connector
- Serial console pin header
- Front panel pin headers
- 24pin ATX power connector
- 5525 12V DC jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5B+ is a single board computer using the Rockchip
RK3588 SoC.
- https://radxa.com/products/rock5/5bp
Hardware
--------
- Quad Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU
- 6 TOPS NPU
- 4/8/16/24/32GB LPDDR5 RAM
- 16/32/64/128/256GB on-board eMMC (optional)
- 16MB SPI NOR flash
- microSD card slot
- Wi-Fi 6 (Realtek RTW8852BE)
- 2.5 Gigabit Ethernet port with PoE (additional PoE HAT required)
- USB 3.1 Gen1 Type-C HOST/OTG port
- 2x USB 3.1 Gen1 Type-A HOST ports
- 2x USB 2.0 Type-A HOST ports
- 2x M.2 M Key connectors with PCIe 3.0 x2
- M.2 B Key connector
- SIM card slot
- RTC battery connector
- PWM fan connector
- 20x2 pin header
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix probing and load correct drivers
when using last backports.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Airoha EN7581 NPU firmware present in linux-firmware.
Support for it is fully upstream with the Ethernet part fully pushed and
the Wireless Offload currently in progress for various WiFi chip.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport support for Aeonsemi AS121xxx PHY. The PHY require dedicated
firmware to be loaded to correctly work and support a big family of
Aeonsemi PHY that provide from 1G to 10G speed.
Automatically refresh all affected patch and file (rtl PHY).
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for Aeonsemi AS21xxx firmware blob. Firmware has been
submitted and accepted to linux-firmware. Current version is 1.8.2.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently it is printed as "null" (including quotes). Display it the same
as old iwinfo as unknown (no quotes).
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
When creating the PSK file, the old script sets `mac` to
`00:00:00:00:00:00` when `mac` is not specified (see [here][1]),
creating hostapd configuration lines like:
vlanid=10 00:00:00:00:00:00 MyStrongPassword
That matches any MAC address (a wildcard). The `ucode` script alternative
misses the default, so set it.
[1]: 9c26d14489/package/network/config/wifi-scripts/files/lib/netifd/hostapd.sh (L428)
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7a86ef53075a fix running bridger with stderr debug output
f6afcb04f2ef nl: add missing dump flag for RTM_GETTFILTER
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Most drivers have this as const. Especially upstream in the kernel.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19911
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When a wifi-iface section is used either for multiple vifs or MLD links,
make it possible to configure the per-radio/link macaddr.
When MLO is enabled, the main macaddr is used for the MLD interface.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
33fb6c738bc4 P2P2: Enable some testing parameters without CONFIG_TESTING_OPTIONS
56616c4183a6 P2P2: Update device name with USD device found
1d791939dcdf Cancel pending connect radio work when network is removed
8235e21d7fe3 P2P: Fix preferred frequency list size handling in p2p_check_pref_chan()
4bc754d9c727 Add QCA vendor interface to enable/disable TX power limit
d65f5705df98 Add QCA vendor attribute to disable A-MSDU address check validation
74881765b7fb nl80211: Use i802_bss in qca_set_allowed_ap_freqs() to use correct ifindex
ca8303135cbb P2P2: Set P2P mode to the driver on P2P GO device
063ae7af68dc ACS: Fix incorrect index calculation for primary channel
4aa3a58377c1 ACS: Validate all channels in a segment before selection
02c9d3376224 ACS: Extend support to exclude 6 GHz non-PSC in non-offloaded ACS
307365eb57bb tests: Add test for ACS exclude 6 GHz non-PSC
0721e4886316 Add QCA vendor attribute to configure EHT RTWT support
76b39db44c77 QCA vendor attribute to configure BTM MLD Recommendation For Multiple APs support
2faeffdeca22 AP MLD: Properly deinit sm of non-ML STA connected to ML AP
e4f4e5a872a5 AP MLD: Fix STA's flag wrongly updated in SME-in-driver cases
ec6cade42c0f Increase buffer size to handle long freq_list entries in config
0522585da7b0 Write freq_list as per-network item in wpa_supplicant.conf
5e527704b912 Use SCS reconfiguration logic under CONFIG_NO_ROBUST_AV
5d6214a724c1 PASN: Clear driver/firwmare ranging context if PASN Auth 1 fails
14dc782d50db DPP: Avoid generating DPP shared secret(z) for non-association links
40326b60b17a RSNO: Allow OWE to be configured in RSN overrides in AP processing
acadef1b04d5 hostapd_cli: Open a new hostapd connection on ping failure when using -a
ac0d9bd80ec5 Add QCA vendor attributes to configure global TX chain mask
f5b8ef6c966a Add QCA vendor attributes for MSDU TX statistics
6c11fcefe4fc hostapd: Prevent blocking sends on control interface monitor socket
0bbb8a66f64c AP MLD: Remove redundant outer loop in hostapd_notif_disassoc_mld()
52fb5ccd91f3 AP MLD: Avoid using mld_id to identify partners
7bb930d50b5f wpa_supplicant: Add option to disable 80+80 MHz opclass advertisement
9001059bd6ad tests: Make dbus_connect_oom more robust
663fb1940231 AP MLD: Fix hostapd_is_mld_ap() check
590f3bdb4c61 AP MLD: Rename hostapd_is_mld_ap() to hostapd_is_multiple_link_mld()
b13b69a235f7 Add VLANID in the AP-STA-CONNECTED events
c1e8b1c6462b SAE: Assign VLAN when using PMKSA caching
9bc29dcdfdee SAE: Default password binding through control interface
9de127c31c40 tests: More testing coverage for SAE with multiple passwords
5ce1d4180386 nl80211: Fix crash by cancelling scan timeout before a BSS is removed
ca266cc24d87 nl80211: Fix crash by setting the drv->ctx properly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
wmcpu_emi node was removed in commit:
b286fd8a39 ("uboot-mediatek: adjust the reserved memory regions")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19855
Signed-off-by: Robert Marko <robimarko@gmail.com>
NILFS is a log-structured file system developed for Linux.
NILFS provides versioning capability of an entire file system
and continuous snapshotting that allows users to restore files
mistakenly overwritten or destroyed a while ago.
Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NILFS is a log-structured file system developed for Linux.
NILFS provides versioning capability of an entire file system
and continuous snapshotting that allows users to restore files
mistakenly overwritten or destroyed a while ago.
Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Increase mt7986 ATF reserved memory to 256 kiB to follow the linux
kernel and Trusted Firmware-A changes.
* Remove unnecessary reserved memory region for the WiFi hardware. The
u-boot can not drive the WiFi hardware. Hence we don't need to keep
this memory region.
* Remove useless node labels and update comments.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6e4ffe2c6657 ucode: add function for getting the number of entries in a snapshot
a62edd89255b ucode: add support for fetching kernel tracepoint events
edeb4d6dc690 udebug-cli: add support for streaming tracing data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Release Notes:
* Support enabling/disabling rts/cts. Not sure if this really works as
hoped though.
* Improved compiler options to build smaller sized binaries.
* Sept 15, 2022: Fix per-peer txpower to not over-ride tpc when value
is 0 (ie, not set yet). This in turn fixes TPC over-ride through the
txo path.
* April 4, 2023: Fix uninitialized minccapwr threshold variables,
reported by Sebastian.
Candela Technologies has already used this beta firmware in their
commercial product "LANforge". And the -ct firmware homepage states
that "This is code is not being changed much, and should be considered
for stable use now." On QCA9888 and IPQ4019, I didn't catch any speed
or stability issues compared to the previous version. Therefore, I
think it is worth updating this beta version.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19042
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Release Notes:
* Attempt to fix crash in scanning logic by making probe_timer
ignore re-arm.
Candela Technologies has already used this beta firmware in their
commercial product "LANforge". On QCA9882, I didn't catch any speed
or stability issues compared to the previous version. Therefore, I
think it is worth updating this beta version.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19042
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
resolves FTBFS where internal option DROPBEAR_SHA512 wasn't enabled by any of options
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19715
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenWrt layerscape target does not use this command. If the host is
missing gnutls, this tool will fail to build. Fix build error:
tools/mkeficapsule.c:20:10: fatal error: gnutls/gnutls.h: No such file or directory
20 | #include <gnutls/gnutls.h>
| ^~~~~~~~~~~~~~~~~
Fixes: c773c3f4d3 ("uboot-layerscape: bump to lf-6.12.20-2.0.0")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19836
Signed-off-by: Robert Marko <robimarko@gmail.com>
All of this uses OF now. No need to keep platform data around.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19804
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now devicetrees imported from Linux kernel release are used, so update
DEVICE_TREE to use correct path. A patch was backported to increase
SYS_MALLOC_F_LEN for stm32mp13 (more alloc space is needed due to SCMI
update to protocol v2.0).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19779
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3d953628bf17 udebugd: add support for setting an override config
93f6df0240e5 udebug-cli: add support for overriding config on the command line
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for the Texas Instruments BQ32000 I2C real-time clock chip.
Tested on a custom board based on Hi-Link HLK-7628N.
Signed-off-by: Ondrej Kolar <ondrej@kolarovo.cz>
Link: https://github.com/openwrt/openwrt/pull/19764
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Initialize data to {} if null before calling mac80211.sh
to avoid a confusing error message in the syslog.
Fixes: https://github.com/openwrt/openwrt/issues/14010
Signed-off-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cosmetic change]
f3fc0b760406 libuci: fix false positive warning on older gcc versions
9033e8c27253 blob: use blobmsg_parse_attr in __uci_blob_check_equal
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The option iface should be optional according to the description
of /etc/config/wireless in order to avoid repeating the definition
for each virtual interface.
Signed-off-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
843a736a4e26 ubus: fix type check in procd ubus data callback
94c3869941b0 interface: avoid memleaks on invalid interfaces
6ead304877ad global: use blobmsg_parse_attr
813b9882dbab config: add support for defining devices via procd data
575b04326e32 config: add support for defining interfaces via procd data
a0be934399cf examples: sync wireless.uc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Modernize the target slightly to use kernel+dtb FIT images in all
subtargets. LZMA compression will be used for the cortexa53 devices,
and we'll stay conservative and use gzip for the cortexa7/a8 devices
due to performance differences.
Tested-on:
- Linksprite pcDuino v2 (cortexa8 / A10)
- Olinuxino Micro (cortexa7 / A20)
- Banana Pi M2 Berry (cortexa7 / V40)
- Banana Pi P2 Zero (cortexa7 / H2+)
- Xunlong Orange Pi 2 (cortexa7/ H3)
- OrangePi PC Zero 2 (cortexa53 / H616)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Running the bootstrap script autogen.sh
handles the execution of autotools already,
so calling autoreconf before configure
makes this happen twice, which is unnecessary
and can lead to an occasional build problem.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/19748
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, the build system overrides the value of the CC variable
for actual compilation after configuring for target builds.
However, the configure script now modifies the CC variable
to include "-std=gnu23" when the test for C23 features is successful.
The configure script also tests for the ability to use alignof
without including the stdalign.h header, and only includes it if necessary.
The test in the configure script is being done with the C23 standard option
but the compilation is being done without the C23 standard option,
leading to an unusual build error where alignof() is not defined.
Resolving the conflict between the autoconf macros and the build system
causes several other packages to fail, so instead in the meantime,
force the use of C23 standard to compile as part of the new standard
includes alignof as a keyword to deprecate the stdalign.h macro.
Forcing use of the new standard is safe for target builds
as the toolchain is known to support the option
and is always within our scope of version control.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/19748
Signed-off-by: Robert Marko <robimarko@gmail.com>
OpenSSL 3.5.2 is a bug fix release:
This release incorporates the following bug fixes and mitigations:
Miscellaneous minor bug fixes.
The FIPS provider now performs a PCT on key import for RSA, EC and ECX.
This is mandated by FIPS 140-3 IG 10.3.A additional comment 1.
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc (Intel N150 based box)
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Execute scripts in /etc/rc.wps until one of them returns a exit code of 0.
Split up sta and ap handling of wps into separate scripts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The cdns3 driver can be built without usb host mode support. Fix
dependencies to handle the case it is built with only gadget support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Build DWC3 driver in the right mode:
- host mode if kernel have usb host support only.
- gadget mode if kernel have usbgadget support only.
- dual-role mode if kernel have both usb host and usbgadget support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The usb role driver does not depend on the kernel config CONFIG_USB (host
side support). It only depends on the kernel config CONFIG_USB_SUPPORT.
Now it depends on the OpenWrt configurations USB_SUPPORT or
USB_GADGET_SUPPORT (usb and usbgadget features). We can assume that if usb
or usbgadget features are set, CONFIG_USB_SUPPORT has been set in the
target/subtarget kernel config.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The usb gadget drivers don't depend on usb host support, so fix the package
dependencies accordingly.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move usb-common driver from usb-core package to a new usb-common package.
The usb-common driver is needed by usb-gadget driver which can be used
without host support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This newly supported device has the same env partition size and
offset as SIMAX1800T.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19455
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for building the ds2438 one-wire kernel module.
Signed-off-by: Andres Heinloo <andres@gfz.de>
Link: https://github.com/openwrt/openwrt/pull/19694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While this is discouraged to disable this option, both upstream and OpenWrt allows one to do it.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19611
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
84372dab89a8 hotplug: switch to using avl tree for hotplug subsystems
4d023b8a8c51 hotplug: send event notifications
467800980021 hotplug: ensure that the button subsystem is always registered
Signed-off-by: Felix Fietkau <nbd@nbd.name>
kmod-sfc should add support for Solarflare SFC9000 series based cards.
However after kernel 5.19, support for the 'Siena' subclass of
SFN5000/6000 devices has been separated out since they went EOL as they
are no longer being actively developed. As kmod-sfc no longer provides
driver support for these cards and hasn't since kernel 5.2, a new kernel
module is needed to support these 10Gb Ethernet cards. More info here:
https://cateee.net/lkddb/web-lkddb/SFC_SIENA.html and here:
https://www.phoronix.com/news/Solarflare-SFC-Siena-Linux-5.19
The module can be compiled in separately and works if kernel is custom
compiled;
OpenWRT has made these changes already with the SFC 'falcon' subclass of
drivers already. See 3c5d70a and e5ba6e9
This is building on excellent work by @ynezz and @nasbdh9
Signed-off-by: Steve Wavler <trenchcoatjedi@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19647
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This will be used in the following commit to move MAC assignment of the
DSL interface to NVMEM.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17289
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds kernel module support for Microchip MCP342x family of I2C ADCs.
Tested on a custom board based on Hi-Link HLK-7628N.
Signed-off-by: Ondrej Kolar <ondrej@kolarovo.cz>
Link: https://github.com/openwrt/openwrt/pull/19619
Signed-off-by: Robert Marko <robimarko@gmail.com>
Estimate the tx throughput based on the expected per-packet tx time.
This is useful for mesh implementations that rely on expected throughput,
e.g. 802.11s or batman-adv.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RETSIGTYPE macro was historically used for signal handler return types,
defaulting to int on some legacy systems. This is no longer needed,
so we now use void as the return type.
Fixes a compiler error:
error: assignment to 'void (*)(int)' from incompatible pointer type 'int (*)()' [-Wincompatible-pointer-types]
Link: https://github.com/openwrt/openwrt/pull/19681
Signed-off-by: Nick Hainke <vincent@systemli.org>
Unless HE/EHT is enabled, the client should not process the RSN override IE.
This prevents picking up unsupported ciphers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow toggling autostart even for disabled devices
When switching from enabled to disabled, call teardown instead of setup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
GS1900-48 is missing from package/boot/uboot-tools/uboot-envtools/files/realtek, so add it to be consistent.
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/19596
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes a crash on some config reload types
Fixes: 816c2d86e7 ("hostapd: add support for MLO interfaces in ucode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MLO can be enabled by configuring a wifi-iface section with multiple
radios, like this:
config wifi-iface
list radio 'radio0'
list radio 'radio1'
option mlo '1'
option ssid 'OpenWrt'
option mode 'ap'
option network 'lan'
...
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MLO interface config is provided in a separate ubus call before
adding regular per-phy interfaces.
Preparation for full MLO support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3a7878065829 system-dummy: add missing vrf functions
471d9d6abb6d CMakeLists.txt: bump minimum required version
c3a0255e2150 scripts: fix dummy mode on systems where libubox is in /usr/local
7a3b281230e4 update example mac80211 script and wireless config
d9f2dd2614f2 wireless: replace with ucode scripts
74c22601baad wireless: add MLO support to example scripts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update package to the latest stable version.
All patches automatically refreshed.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/19621
Signed-off-by: Nick Hainke <vincent@systemli.org>
As discussed in openwrt#17517, there are contents of hostapd's configuration file logged in syslog.
This includes critical information like `passphrase`. To circumvent this condition,
this commit logs only "inline" if config_fname is inline data.
Otherwise the upstream logic of hostapd applies.
Fixes: openwrt#14049
Signed-off-by: Christian Korber <ck@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/17718
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a package for the last util needed to query /var/log/wtmp
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19586
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix the crash and warnings for the newly introduced env on mtd
implementation. Also backport an out-of-bound access fix for the
"askenv" command.
Fixes: 41a9c9de66 ("uboot-mediatek: update to v2025.07")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
In the upstream implementation of env in mtd, ENV_MTD_NAME symbol
was renamed to ENV_MTD_DEV. Therefore, we have to adjust the symbol
to make it work properly. ENV_SIZE_REDUND symbol will be removed
in this patch because the upstream env in mtd implementation no
longer requires it.
Fixes: 41a9c9de66 ("uboot-mediatek: update to v2025.07")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The popular Mediatek target has many u-boot modified devices. This
change can keep the u-boot source code tidy.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
When running find_mmc_part on a system without MMC or when the given
root device does not exist, an error message is printed to stderr.
grep: /sys/block/mmcblk*/mmcblk*p*/uevent: No such file or directory
Silence this error message.
Since find_mmc_part is mostly used to get block devices of MMC
partitions and the negative result (partion not found) is checked for by
the caller, the error message can be silenced without causing any
negative impact.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/19492
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This enables software that requires this cipher suite (e.g. OpenThread Border
Router) to be compiled against the shared library rather than a separate copy.
Signed-off-by: Karsten Sperling <ksperling@apple.com>
Link: https://github.com/openwrt/openwrt/pull/19489
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Select the kmod-drm-display-helper package instead of depending on it.
kmod-drm-display-helper is hidden now, so the user can not manually
select it.
This fixes the build of the imx target.
Fixes: 8bcc6d1894 ("kernel: kmod-drm-display-helper: Mark hidden")
Link: https://github.com/openwrt/openwrt/pull/19532
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-crypto-lib-aescfb is marked hidden and not selected by any other
package, it can not be build.
The Kconfig option in the kernel has no title, so it can not be
selected, it is only selected by CONFIG_TCG_TPM2_HMAC in the kernel.
Fixes: ef2310b031 ("kernel: modules: update dependency for kmod-tpm")
Fixes: aa51a1c13a ("kernel: kmod-crypto-lib-aescfb: Mark hidden")
Link: https://github.com/openwrt/openwrt/pull/19532
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently the system boots up, but is unusable because pressing enter
does not provide login with error:
login: can't get SID for root
This is happenning, because login.c passes the Linux username directly
to get_default_context(), while libselinux expects an SELinux user
identity, causing the call to fail for users without a matching SELinux
name (e.g., root) and aborting login on SELinux-enabled systems.
Fixes: #19075
Upstream-Status: Submitted [https://lists.busybox.net/pipermail/busybox/2025-April/091407.html]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/19080
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to a newer bugfix release of gettext.
Include gnulib-l10n as a new dependency.
All patches are automatically refreshed.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16522
Signed-off-by: Robert Marko <robimarko@gmail.com>
This package is a supplement for part of gettext
that uses gnulib sources, and includes the localizations
for messages specifically in gnulib files.
This is being added as a separate package
instead of a build target of gnulib
because that method of acquiring the localizations
requires the use of gettext and would be a reverse dependency.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16522
Signed-off-by: Robert Marko <robimarko@gmail.com>
The usage of automake is left over
after the patch which required it was removed
since the new configure option
"--without-cli" was added to upstream.
Remove the usage of autotools to save build time.
Ref: 72e6e0b85 ("nftables: introduce experimental nftables")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16522
Signed-off-by: Robert Marko <robimarko@gmail.com>
The nfs_layout_flexfiles.ko and nfs_layout_nfsv41_files.ko file are
build automatically when CONFIG_NFS_V4_1 is selected, we can not
deactivate them. Pack them into the NFS package too. I do not know if we
should also load them automatically.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_B53 kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-dsa-b53 depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_BCMGENET kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-bcmgenet depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_PARMAN has no title and can not be
directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_OBJAGG has no title and can not be
directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_DRM_DISPLAY_HELPER has no title and can
not be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_DRM_BUDDY has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_V4L2_ASYNC has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_V4L2_FWNODE has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_CRYPTO_LIB_AESCFB has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_CRYPTO_ENGINE has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_IIO_BACKEND has no title and can not be
directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel driver configuration depends on PINCTRL.
Show this driver only on targets supporting pinctrl.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These drivers depend on the kernel option CONFIG_PWM, only add them to
OpenWrt for targets which have PWM support.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel driver configuration depends on ath79 or compile test and not
on PCI. Allow this package in OpenWrt only for the ath79 target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fallback to default mbedtls configurations in case of the package is
not configured. It is possible for some reasons it get built even if
it's unselected because of build system bugs or other build-only
dependencies. In this case current behavior will comment out all
necessary configurations and lead build errors.
Fixes: 5359639c2b ("mbedtls: Apply configuration in Configure instead of Prepare")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19495
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
5d10084ea885 lib-ucode.c: add #define _GNU_SOURCE
a95364b41d52 udebug-cli: fix terminating uloop
c00eb9b685a8 ucode: use FILE handle for pcap output
4265167cb6e8 ucode: add error reporting to pcap_write
4a908ee731a6 udebug-cli: stop event loop on write failure
6e04f4187231 ucode: use ucv_resource_create_ex for remote rings
c297f04e1852 ucode: drop use ucv_resource_create
f207d37a1055 ucode: add support for specifying ring format
98683a94bcdd ucode: support appending array data, similar to socket.send()
a7ecd483ed38 ucode: allow calling udebug.init() multiple times
d4a4c788c416 ucode: fix allocation size of local ring meta
184706abaf50 ucode: add timestamp argument to foreach()
8442c948c193 ucode: add function for getting ring information
f4958a4c591a ucode: add const entries for enum udebug_format
14d4fec36993 udebug-cli: add logstream command
6ed8536142bb ucode: fix entries/size confusion
Signed-off-by: Felix Fietkau <nbd@nbd.name>
6953f19 wireless-regdb: Update regulatory info for Indonesia (ID) for 2025
2e8214e wireless-regdb: Permit 320 MHz bandwidth in 6 GHz band for GB
a94f685 wireless-regdb: Update regulatory info for Egypt (EG) for 2024
7628ce2 wireless-regdb: Update regulatory rules for Brazil (BR) on 6GHz
4411b39 wireless-regdb: Update regulatory info for Vietnam (VN) for 2025
490f136 wireless-regdb: Update regulatory info for Estonia (EE) for 2024
c56c663 wireless-regdb: update regulatory rules for Paraguay (PY) on 6 GHz for 2025
5a8ced5 wireless-regdb: Update regulatory info for CEPT countries for 6GHz listed by WiFi Alliance
5fd8ee3 wireless-regdb: update regulatory rules for Bosnia and Herzegovina (BA) for 6 GHz
e05260a wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/19474
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DRM modules for simple (ie. raw, non-eDP) panels can be used also
by platforms others than Freescale i.MX.
Create an individual package for it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Partially revert commit 332645a610 ("uboot-mediatek: sync with
mtk-openwrt/u-boot 20250711") by dropping unused PHY drivers which come
with large embedded firmware (and are hence inacceptable for upstream)
and restoring our previous version of the Airoha EN8811H driver which is
known to work and load firmware from the eMMC boot1 hardware partition
instead of embedding it in the driver.
In future we may switch to the upstream Airoha EN8811H driver which
allows loading the firmware either from a filesystem or overloading the
en8811h_read_fw() for board which may eg. store that firmware directly
inside a eMMC hardware partition or UBI volume, like the BPi-R3 mini
does.
See also:
https://patchwork.ozlabs.org/project/uboot/patch/20250615131243.30770-1-lucienzx159@gmail.com/
Fixes: 332645a610 ("uboot-mediatek: sync with mtk-openwrt/u-boot 20250711")
Reported-by: Adrian Bente
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This ensures mbedtls_config.h is correctly updated and the package rebuilt
accordingly when configuration options are changed after the source is first
prepared.
Signed-off-by: Karsten Sperling <ksperling@apple.com>
Link: https://github.com/openwrt/openwrt/pull/19358
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update mediatek arm-trusted-firmware to the latest version.
Remove upstream patch:
0004-mediatek-snfi-fix-return-code-when-reading.patch
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The build error has been fixed by the upstream commit:
03e598263e38 ("tools: fix build without LIBCRYPTO support")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Most ramips target devices use the legacy uImage format. This
patch extends the imsz/imszb commands to support detecting the
image size of legacy uImage.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add back the default LK image header to generate u-boot-mtk.bin. This
is the default behavior before u-boot v2022.01. If "u-boot-mtk.bin"
doesn't boot, please try "u-boot.bin" and report it.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Update to the latest version.
Suppressed patch:
100-04-env-add-support-for-generic-MTD-device.patch[1]
[1] 03fb08d4ae
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Package kernel modules for PS/2 mouse support, mostly to allow
using touchpads and trackpoints built-into laptops (many of those
are connected using classic i8052-compatible PS/2 I/O).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buildbot revealed that on the x86/geode target, on which CONFIG_DRM=y isn't set,
kmod-i2c-hid misses the dependency on kmod-drm. Fix that to fix the build for
x86/geode.
Fixes: c83e275c9b ("kernel: package modules for I2C HID devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add an OpenWrt-based U-Boot build for this device, allowing for more
flexibility and customization.
Expected behaviour
------------------
When plugging the device, keeping the reset button pressed will enter
TFTP recovery mode: the board will send requests for the initramfs file
(openwrt-mediatek-filogic-glinet_gl-mt2500-initramfs-kernel.bin) from
IP 192.168.1.1 to 192.168.1.10 TFTP server.
The bootloader will populate the environment with the unit serial number
as reported by the "sn" value in eMMC, the "sn_bak" value, the country
code and ddns. WAN and LAN MAC addresses are reported in the environment
as well.
Limitations
-----------
No web interface is available, and only the LAN port can be used for
system recovery.
Notes
-----
This port has been tested with the Maxlinear version only, and with a
board that does not exhibit eMMC communication problems. Even though eMMC
frequency has been lowered, some testing is probably needed and always
very welcome.
A -factory image has been introduced, and is only needed when using the
"Load Firmware via TFTP then write to eMMC." boot menu function.
The device has not been converted to use uImage.FIT including the rootfs
to keep compatibility with stock bootloader and firmware.
Installation
------------
From a Linux root shell:
0. Transfer the needed files to the board, placing them in /tmp.
1. Make sure your U-Boot environment is erased: all of my units came with
unpopulated environment, but I am not sure this is always the case.
Issue the command
cat /dev/zero >/dev/mmcblk0p2
(you will get a "no space left" error, which is reasonable and expected).
2. Unlock the eMMC boot area where BL2 is located:
echo 0 >/sys/block/mmcblk0boot0/force_ro
3. Write the new BL2 code:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-preloader.bin >/dev/mmcblk0boot0
4. Write new BL31+U-Boot image:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-bl31-uboot.fip >/dev/mmcblk0p4
5. Reboot.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This commit updates the OpenWrt-based U-Boot for this device, allowing
to boot a FIT firmware image stored in an SD card.
The environment has been updated accordingly to allow for managing images
on the two different supported firmware boot media configurations
(NOR or SDMMC).
Erasing the U-Boot environment when upgrading is recommended, so that
the correct DTS overlay is applied.
New behaviour
-------------
The default environment "bootconf" variable is set to
config-1#mt7981b-gatonetworks-gdsp-gps
rendering the GPS module accessible.
You may set it to something like
config-1#mt7981b-gatonetworks-gdsp-sd
to be able to use the MMC controller.
To boot from a firmware image stored in an SD card, you may set the
bootmedia environment variable:
# fw_setenv bootmedia sd
and reboot.
Should the bootmedia variable be absent or it's content not recognized
as valid (e.g., does not contain "nor" or "sd"), NOR boot will be
attempted.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building perf on mips/malta fails on intel-pt-decoder due to a header issue
previously seen in f434643857 ("perf: fix build on PowerPC"):
In file included from util/intel-pt-decoder/intel-pt-insn-decoder.c:12:
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h: In function 'insn_field_set':
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:56:21: error: implicit declaration of function '__cpu_to_le32'; did you mean 'cpu_to_le32'? [-Wimplicit-function-declaration]
56 | p->little = __cpu_to_le32(v);
| ^~~~~~~~~~~~~
| cpu_to_le32
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h: In function 'insn_set_byte':
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:64:20: error: implicit declaration of function '__le32_to_cpu'; did you mean 'le32_to_cpu'? [-Wimplicit-function-declaration]
64 | p->value = __le32_to_cpu(p->little);
| ^~~~~~~~~~~~~
| le32_to_cpu
Extend the previous powerpc fix to mips, disabling intel-pt-decoder build.
cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19426
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package driver modules for I2C HID devices such as touchpads,
touchscreens and trackpoints found on some laptops. Only the ACPI
firmware variant of the driver is packaged for now as that's what I got
for testing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A new function "get_linux_version()" to normalize and print the
kernel version as an integer. In some migration scripts, it is
useful for checking the Linux kernel version.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The number of serial interfaces for the chip 8250 can be configured at
build time. This is currently not configurable and is always set to 16
interfaces. This is too little for some small embedded devices and too much
for others (x86_64). Therefore, this commit creates the possibility to set
this at compile time.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/19217
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Host default environment doesn't provide/require gnutls headers needed
for building mkeficapsule tools, and as tegra target doesn't require EFI
capability, disable the build of mentioned tool.
Fixes: 92cd360aac ("uboot-tegra: bump version to 2025.04")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250713125126.215092-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add new option to bootmenu which allows to boot the system from USB.
You can use dd to prepare USB with initramfs:
- dd bs=1M if=openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-factory.ubi of=/dev/sdX
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18949
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use common function ubootenv_add_mmc
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The direction needs to be included in the IOCTL call.
Fixes: b91d7d9d78 ("ltq-*-app: extend ubus metrics/statistics")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19363
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band
wireless access point. Very similar to already supported APL26-0AE,
which all antennas are external, while this variant has internal
antennas. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 1x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "ap135.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 ap135.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Notes
By default no power is provided on USB port, so attached USB devices
won't enumerate. To change that enable regulator with:
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
To disable power write "disabled" to the same file.
Ther regulator state will reset on reboot, consider running this command
on hotplug event or add it to /etc/rc.local. The hotplug event should
look like this:
if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
fi
Place it in /etc/hotplug.d/usb/10-usb-power.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allows to enable/disable attached regulators from userspace, i.e. by
simply writing value to a sysfs exported state file. Useful in case of
USB port VBUS toggled by GPIO.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
glibc 2.39 has removed libcrypt completely.
solution: link against libxcrypt built with glibc compatibility.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19293
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
glibc 2.39 has removed libcrypt completely.
solution: link against libxcrypt built with glibc compatibility.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19293
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
glibc 2.39 has removed libcrypt completely.
solution: link against libxcrypt built with glibc compatibility.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19293
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
glibc 2.39 has removed libcrypt completely.
solution: link against libxcrypt built with glibc compatibility.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19293
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
glibc 2.39 has removed libcrypt completely.
solution: link against libxcrypt built with glibc compatibility.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19293
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
glibc 2.39 has removed libcrypt completely.
solution: link against libxcrypt built with glibc compatibility.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19293
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
glibc 2.39 has removed libcrypt completely.
solution: link against libxcrypt built with glibc compatibility.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19293
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add uboot-envtools support for Gateworks venice boards based on i.MX8M
SoC's (imx_cortexa53) which boot from and store their U-Boot env on
eMMC boot0 hardware partition.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19347
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream has disabled SHA-1 algorithms by default since version 2025.87.
SHA-1 has known weakness and most SSH implementations support alternatives.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
It's hard or even impossible to track affected sources
so it's safe to remove all built objects (if any).
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
This allows to fine-tune dropbear build options.
This change is heavily based on similar work done by Marius Dinu earlier
so I'd like to say many thanks to original author.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- update dropbear to latest stable 2025.88;
for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- rewrite 100-pubkey_path.patch
- refresh remaining patches
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.
wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.
Use the correct config key and calculation for mesh-interfaces.
Signed-off-by: David Bauer <mail@david-bauer.net>
Since upstream commit:
b809fc656e763296f227b9b31e8f225e5977a8af ("perf build: Shellcheck support
for OUTPUT directory")
perf will attempt to run shellcheck on the test shell scripts, however
there is no point in doing this in OpenWrt and while perf checks for
shellcheck presence on your host it can fail to build in some cases.
So, simply disable it for now.
Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>
BUILD_BPF_SKEL was set to 1 by default in upstream commit:
9925495d96efc14d885ba66c5696f664fe0e663c ("perf build: Default
BUILD_BPF_SKEL, warn/disable for missing deps")
Prior to that, it was disabled by default and you had to enable it to
build BPF skeleton support.
So in order to fix perf compilation with kernel 6.12, lets disable
BUILD_BPF_SKEL.
Fixes: #19310
Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update to 6.5.
Removed patch from pre-2012: 101-ncurses-5.6-20080628-kbs.patch
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19335
Signed-off-by: Robert Marko <robimarko@gmail.com>
Without the newly introduced flag, building with libc ends in errors such the below.
There is an upstream fix[1], but backporting it is not straight forward.
/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:81:21: error: redefinition of 'struct std::__byte_operand<unsigned char>'
81 | template<> struct __byte_operand<unsigned char> { using __type = byte; };
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:78:21: note: previous definition of 'struct std::__byte_operand<unsigned char>'
78 | template<> struct __byte_operand<bool> { using __type = byte; };
| ^~~~~~~~~~~~~~~~~~~~
make[4]: *** [Makefile:438: ../obj_s/cursesp.o] Error 1
1. https://ncurses.scripts.mit.edu/?p=ncurses.git;a=commit;h=394a1a6cf317912584592e33184ef550e738a4b9
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19335
Signed-off-by: Robert Marko <robimarko@gmail.com>
Split the xcrypt package build into two Makefiles and a common part for
the version definition in order to work-around build problems when
combining VARIANT with BUILDONLY and scoped InstallDev.
This is done in order to skip build of libcrypt-compat in case we are
not building against glibc in order to prevent libcrypt.so shared
library being present in staging_dir and by that breaking multiple
packages which then will link against it.
Fixes: e3cf7088f1 ("libcrypt-compat: introduce package")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/19353
Signed-off-by: Robert Marko <robimarko@gmail.com>
6df761e0e6c7 mt76: fix signature of platform_driver remove funtions for newer kernels
5724be1a6b12 wifi: mt76: Replace strlcpy() with strscpy()
c4a114e2b8c9 wifi: mt76: fix queue assignment for deauth packets
243e572d89fc wifi: mt76: add a wrapper for wcid access with validation
e41c7785589f wifi: mac80211: get tx power per link
d70f62b8f1c7 wifi: mt76: fix vif link allocation
7b3cd3274a24 wifi: mt76: mt7996: Fix secondary link lookup in mt7996_mcu_sta_mld_setup_tlv()
cf89b6218043 wifi: mt76: mt7996: Rely on for_each_sta_active_link() in mt7996_mcu_sta_mld_setup_tlv()
d71108eedab1 wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()
32f8c5849ed1 wifi: mt76: mt7996: Fix mlink lookup in mt7996_tx_prepare_skb
ffff9f71e29d wifi: mt76: mt7996: Fix possible OOB access in mt7996_tx()
afe63e758196 wifi: mt76: mt7996: Fix valid_links bitmask in mt7996_mac_sta_{add,remove}
68dd28b99dad wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()
293778652452 wifi: mt76: mt7996: Move num_sta accounting in mt7996_mac_sta_{add,remove}_links
a94166b21e20 wifi: mt76: Get rid of dma_sync_single_for_device() for MMIO devices
87873d854e51 wifi: mt76: mt7925: Fix null-ptr-deref in mt7925_thermal_init()
06ba3d5e91f4 wifi: mt76: mt792x: Limit the concurrent STA and SoftAP to operate on the same channel
b9f4e0df317d wifi: mt76: mt792x: improve monitor interface handling
ec95319fd3fb wifi: mt76: mt7921s: Introduce SDIO WiFi/BT combo module card reset
dd2d862251cb firmware: add missing mt7990 eeprom files
05eaa56bc7a4 firmware: update mt7992 firmware to 20250328
32ca2b6db354 firmware: update mt7996 firmware to 20250328
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k ahb patch was updated to match the latest upstream version,
however the openwrt DT files still use the older names.
Add those as extra entries in order to remain compatible until DT files
are fixed.
Fixes: 88f4c32060 ("mac80211: update to version 6.14.11")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
nl80211 events were propagated to the wrong interfaces
Fixes: 2ac791e87d ("hostapd: update to version 2025-06-27")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Manually refreshed:
140-tests-Makefile-make-run-tests-with-CONFIG_TLS.patch
601-ucode_support.patch
Fixed in upstream:
804-hostapd-revert-ACS-Validate-6-GHz-AP-criteria-before.patch [1]
Automatically rebased all other patches.
[1] https://w1.fi/cgit/hostap/commit/?id=0b60826a66885bffa2fd709ed5e48cd5fe241b6b
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
802.11be capable platforms are big enough to not need the mini variant,
and removing it here saves space for other other devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Updates libnetfilter-conntrack to version 1.1.0.
Removes patches which should no longer be needed according to changelog for
libnetfilter-conntrack 1.1.0
Signed-off-by: Ian Ladd <ianwladd@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19282
Signed-off-by: Robert Marko <robimarko@gmail.com>
Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.
Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks
Signed-off-by: Dim Fish <dimfish@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17963
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add OS descriptors support. Configuring OS descriptors allows Microsoft
Windows to bind the right drivers without any additional configuration.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19237
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Automatically rebased: 100-Configure-afalg-support.patch
Changes between 3.5.0 and 3.5.1:
Fix x509 application adds trusted use instead of rejected use.
Issue summary: Use of -addreject option with the openssl x509 application
adds a trusted use instead of a rejected use for a certificate.
Impact summary: If a user intends to make a trusted certificate rejected
for a particular use it will be instead marked as trusted for that use.
(CVE-2025-4575)
Aligned the behaviour of TLS and DTLS in the event of a no_renegotiation
alert being received. Older versions of OpenSSL failed with DTLS if a
no_renegotiation alert was received. All versions of OpenSSL do this for TLS.
From 3.2 a bug was exposed that meant that DTLS ignored no_rengotiation.
We have now restored the original behaviour and brought DTLS back into line
with TLS.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19283
Signed-off-by: Robert Marko <robimarko@gmail.com>
27839f854a58 ubusd: make txq_len field signed
b35b2bc63e8e ubusd: treat EACCES on write like EAGAIN
713e9d19b2b6 ubusd: retry write on EINTR
8bb523ab20e0 ubusd: fix txq_len accounting
b1b783c74742 ubusd: add another tx attempt on enqueueing the first message for a client
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The same function is used twice, so let's make it common.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Functions ubootenv_add_mtd, ubootenv_add_sys_mtd and ubootenv_add_mmc
can be shared so make them common.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, uboot-envtools is being built for a (shared) instruction
set (phase2 in buildbots) instead of target-specific (phase1 in builbots).
So the package does not contain the uci-defaults file specific for each
target_subtarget. (Only the fortunate target with coincidentally the same
instruction set and target as the SDK chosen by the buildbot will have the
uci-defaults file.)
This commit sets the nonshared flag correctly in the Makefile so that
uboot-envtools is built for the target-specific (phase 1).
This is done by using the PKGFLAGS variable which is intended for
per-binary flags (instead of PKG_FLAGS which has a global scope), as
stated in some old commits 349e7b635e[1], 2d7eaf2e15[2], 064e7c8f00[3] and
2cb75cd8b9[4].
While at here, use PKG_URL, instead of URL, which is intended for global
scope. As stated in commit e32edf712b[5].
[1] 349e7b635e
[2] 2d7eaf2e15
[3] 064e7c8f00
[4] 2cb75cd8b9
[5] e32edf712bFixes: #19040
Fixes: 46e376c ("uboot-tools: migrate uboot-envtools to uboot-tools")
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19180
Signed-off-by: Robert Marko <robimarko@gmail.com>
