Include <linux/version.h> and use preprocessor checks to select the appropriate
prototype and definition for hc_wlan_data_bin_read. The third parameter of bin_attribute
read callbacks was changed to 'const struct bin_attribute *' in Linux 6.18; this
change prevents compilation errors on newer kernels while preserving compatibility
with older ones
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch silences compiler warnings about unused variables by explicitly
casting them to void where appropriate.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Partially reverse https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.18.y&id=39cfd5b12160be4f57df1c3ba60139741c827616
to prevent generation of empty modules.builtin.modinfo and modules.builtin
files that cause modules compilation errors.
If an out-of-tree package or any kernel-install rule ran modprobe xyz while
the build was still in progress, and xyz had been configured =y, a clean tree
would already have xyz listed in modules.builtin; with the empty file produced
by the buggy rule it was missing, so modprobe emitted "module xyz not found"
even though the code was sitting inside the freshly built vmlinux.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch fixes the "Unsupported UART type 4" error by adding support
for the UPIO_AU I/O type in set_io_from_upio() (used by Au1x00 and
RT288x). It assigns the correct serial input/output functions
(io_serial_in, io_serial_out) for proper operation when UPIO_AU is
configured.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport minor fixes for the eip93 driver from upstream.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch set introduces support for using the in-tree (mainline)
EIP93 crypto driver for kernel 6.18 and later, along with additional
improvements and fixes:
- Conditional Kconfig/Makefile handling for crypto-hw-eip93 to enable use of the mainline driver with kernel 6.18+.
- Patch 926: Use software AES fallback for small requests in the EIP93 driver.
- Patch 927: Add `mediatek,mtk-eip93` compatible string for upstream kernel device trees.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
- change phy_driver_register and phy_driver_unregister function calls
to phy_drivers_register and phy_drivers_unregister for compatibility
with kernel 6.18
- replace PHY_ANY_ID with "MATCH ANY PHY"
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove symbols no longer present in version 6.18,
add new 6.18 kernel symbols.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refreshed patches for generic/hack-6.18 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refreshed patches for generic/pending-6.18 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refreshed patches for generic/backport-6.18 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove obsolete backport patches already included in kernel 6.18.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add define for kernel 6.18.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
On qca8k multi-CPU-port setups (e.g. qca8337 with ports 0+6 as CPU),
bridging switch user ports that use different conduits can make the host
reachable only from the ports tied to the last-programmed CPU port.
Add a pending kernel patch which makes qca8k merge CPU/DSA-port FDB
programming, so host FDB entries end up on all relevant CPU ports.
Fixes: openwrt/openwrt#17891
Signed-off-by: Kevin Staley <glaciertablet@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21317
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport upstream driver and apply pending downstream patches to
support using the MaxLinear MxL86252 and MxL86282 switches.
The driver supports a native proprietary 8-byte DSA special tag format
(mxl862xx) as well as using an 802.1Q-based DSA tag (mxl862xx-8021q).
All basic bridge, VLAN and LAG operations are supported. A single port
can be used as mirror port. Hardware counters are made available as
ethtool stats or directly serve as interface counters (bytes,
packets).
The switch runs a complex ZephyrOS-based firmware on an integrated
ARC microcontroller, the driver uses the firmware management API over
MDIO to interact with the switch hardware.
Note that the firmware needs to be rather recent (WSP 1.0.78 or later)
to work well with this driver. It can be updated at runtime using devlink.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
FIPS 140-3 recommends that all crypto implementations should be tested
before first use. Testmanager performs initial tests based on existing
test vectors. Not all algorithms have defined test vectors, so to improve
this situation, this commit backports recently added test vectors for
following cipher suites:
* authenc(hmac(md5),cbc(des))
* authenc(hmac(md5),cbc(aes))
* authenc(hmac(sha1),rfc3686(ctr(aes)))
* authenc(hmac(sha224),rfc3686(ctr(aes)))
* authenc(hmac(sha256),rfc3686(ctr(aes)))
* authenc(hmac(sha384),rfc3686(ctr(aes)))
* authenc(hmac(sha512),rfc3686(ctr(aes)))
These vectors were calculated using a software implementation and then
double-checked on Mediatek MT7981/MT7986 (safexcel) and NXP P2020 (talitos).
Both platforms passed self-tests.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/22409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for the following AEAD ciphersuites:
- authenc(hmac(md5),cbc(aes))
- authenc(hmac(md5),cbc(des)))
- authenc(hmac(md5),cbc(des3_ede))
- authenc(hmac(md5),rfc3686(ctr(aes)))
These algorithms are used mainly for backward compatibility with some
older equipment. This is enhanced version of the patch found in the
mtk-openwrt-feeds repo.
All cipher suites were tested using test vectors on the MediaTek MT7981,
MT7986, and MT7988.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/22410
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream 2b81db8a7f4475e141a8ffd7cc745ed9f15962df introduced several new
symbols. This commit adds them and also applies alphabetical order via
./scripts/kconfig.pl target/linux/generic/config-6.12
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22276
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport new field_prep()/get() particularly useful to handle case where a
bitmask is not const and FIELD_PREP can't be used. This permit to replace
manual shift with these macro. (also needed to permit backport of some
patch without modification)
Backport reworked patch that drop the local field_prep()/get() macro in
favor of the global one.
Link: https://github.com/openwrt/openwrt/pull/22479
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In generic, there's a backport from 6.14 that makes this change. Do so
in downstream locations as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21167
Signed-off-by: Robert Marko <robimarko@gmail.com>
When NVMEM is not ready, of_get_mac_address fails. Handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22305
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When NVMEM is not ready, of_get_mac_address fails. Handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22305
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch for improving Huawei MA5671a SFP fixup, which allows
communicating with the module even if the fiber isn't connected.
Link: https://github.com/openwrt/openwrt/pull/22283
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Refresh kernel patches with make target/linux/refresh for each target.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
The single user of the downstream gpio-cascade driver has been switched
to use the upstream gpio-line-mux driver. Thus, we can drop the former
now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport the upstream 'gpio-line-mux' driver which allows to provide a
1-to-many mapping between one physical GPIO and multiple virtual GPIOs,
based on a multiplexer.
For this purpose, there's been a dedicated downstream driver
'gpio-cascade' which is mostly the same, but wasn't upstreamed in the
end. Independently developed, the 'gpio-line-mux' driver was upstreamed
to solve the exact same problem occuring on Realtek-based Zyxel XS1930
switches. Support for those is being worked on, but the hardware uses a
similar quirk for SFP signals. The signals 'RX_LOS', 'MOD_ABS' and
'TX_FAULT' do not have dedicated GPIOs each but all use a single GPIO
which is multiplexed. Depending on the multiplexer state the GPIO line is
connected to one of the signals.
Since the SFP driver needs single GPIOs for the single signals, this
adapter drivers fills the gap to make both work together.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are a number of pse chips already present in upstream Linux.
OpenWrt is starting to support a number of devices can contain various pse
chips. But having all the pse chip combinations defined at the target
level will result in bloat on images.
Present the current upstream Linux pse drivers as packages so that they
can be selectively included per board (rather than per target).
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
[Make it depend on REGULATOR_SUPPORT, and !SMALL_FLASH]
Link: https://github.com/openwrt/openwrt/pull/22172
Signed-off-by: Robert Marko <robimarko@gmail.com>
Advertise the default 'not set' of this CONFIG higher in the tree since
it's already referenced by several other targets, with a few more targets
missing this reference (which fails build to prompt for N/y/m).
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
CONFIG_REGULATOR_QCOM_LABIBB is being disabled by targets manually, so
instead lets disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of disabling CONFIG_REGULATOR_QCOM_SPMI manually per target,
lets simply disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_REGULATOR_QCOM_USB_VBUS showed up on Layerscape recently, and it
looks like multiple targets disable it manually, so simply disable it in
generic configuration instead.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixed the compilation of kernel with the loadable modules support turned off
Signed-off-by: Maksim Dmitrichenko <dmitrmax@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22041
Signed-off-by: Robert Marko <robimarko@gmail.com>
FIPS 140-3 recommends that all crypto implementations should be tested
before first use. Testmanager performs initial tests based on existing
test vectors. Not all algorithms have defined test vectors, so to improve
this situation, this commit backports recently added test vectors for
three cipher suites:
* authenc(hmac(md5),cbc(des3_ede)),
* authenc(hmac(sha224),cbc(aes)),
* authenc(hmac(sha384),cbc(aes)).
These vectors were calculated using a software implementation and then
double-checked on Mediatek MT7981 (safexcel) and NXP P2020 (talitos).
Both platforms passed self-tests.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21970
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
