warning print "ath11k c000000.wifi: failed to flush transmit queue 0"
is observed during busy times.
The mac80211 fallback implementation of `flush_sta` does not handle the per STA queues well.
This is fixed by providing a ath11k specific implementation of flush_sta telling the firmware to flush a given station.
The draining of the transmit queues should therefore stop correctly, even if new packets arrive in the mean time.
An upstream ath11k RFC is available at:
https://patchwork.kernel.org/project/linux-wireless/patch/GV1P250MB14333A5BF24623C4753A10E1E8E0A@GV1P250MB1433.EURP250.PROD.OUTLOOK.COM/
The patch was tested on a Xiaomi AX3600.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Tested-by: Florian Maurer <f.maurer@outlook.de>
Co-authored-by: Benjamin Berg <benjamin@sipsolutions.net>
Tested-by: Flole <flole@flole.de>
Link: https://github.com/openwrt/openwrt/pull/20293
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This includes the following commits from upstream Linux between 6.16 and 6.16.12:
wifi: ath11k: clear initialized flag for deinit-ed srng lists
wifi: ath11k: fix sleeping-in-atomic in ath11k_mac_op_set_bitrate_mask()
wifi: ath11k: fix dest ring-buffer corruption
wifi: ath11k: fix source ring-buffer corruption
wifi: ath11k: fix dest ring-buffer corruption when ring is full
wifi: ath11k: fix group data packet drops during rekey [1]
wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load()
[1] The patch "940-ath11k-Revert-clear-the-keys-properly-when-DISABLE_K.patch" has been removed, as it has been fixed upstream in "wifi: ath11k: fix group data packet drops during rekey" and is added in 945 patch.
Related: https://github.com/openwrt/openwrt/pull/18705
Related: https://github.com/openwrt/openwrt/issues/9555
Related: https://github.com/openwrt/openwrt/issues/14117
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove leading 0 from filename.
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix package name and AUTOLOAD parameter to match the
actual kernel module name (leds-group-multicolor), enabling proper
auto-loading at boot.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20447
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previously, devices would have to select `CONFIG_RTL8261N_PHY=Y` in the
whole target's kernel config. Now that this driver is becoming usable
for devices other than Realtek switches, allow packaging this driver
separately.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/20429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the copy_from_user() and copy_to_user() functions for accessing
memory provided by the user in the ptm netdev iotls.
In addition also check for root permission before executing ioctl.
Suggested-by: Stanislav Fort from Aisle Research
Reported-by: Stanislav Fort from Aisle Research
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add Realtek RTL8822CS support to the rtw88 package.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20423
Signed-off-by: Nick Hainke <vincent@systemli.org>
Currently, the interfaces of the Mellanox Spectrum Switch QSFP ports
are all labeled eth*. Their order doesn't match the faceplate and is
different for each model.
They could be named during boot, but this isn't sufficient because they
support port splitting. After such ports are split, their port naming
begins again with eth*, and the same is true after they are unsplit again.
A hotplug script is used here that reads from the sysfs file
phys_port_name, which contains p1, p2, p3, ... for unsplit ports
and p1s0, p1s1, p1s2 for split ports.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the pre-init boot flag for the e1000e network device
driver so that it is loaded during the early pre-init
stage of the boot process instead of later.
Then, it is possible to rename its network ports via the
ucidef_set_network_device_path function from the
02_network script while booting.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
mt76 as support for generic rates power limits in the devicetree. But the
mt7915 supports beamforming and has another table for configuring the
backoff limits. These can be configured in the DT with the paths-*
properties. The path-*-bf are the ones relevant for beamforming and the
ones without -bf suffix for "traditional" path backoff.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The power-limits for ru and mcs and stored in the devicetree as bytewise
array (often with sizes which are not a multiple of 4). These arrays have a
prefix which defines for how many modes a line is applied. This prefix is
also only a byte - but the code still tried to fix the endianness of this
byte with a be32 operation. As result, loading was mostly failing or was
sending completely unexpected values to the firmware.
Since the other rates are also stored in the devicetree as bytewise arrays,
just drop the u32 access + be32_to_cpu conversion and directly access them
as bytes arrays.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mlxreg-hotplug platform driver was failing to probe due to a missing
I²C multiplexer dependency. Previously, only kmod-i2c-mux-mlxcpld was
declared, but mlxreg also requires kmod-i2c-mux-reg to initialize its
I²C mux functionality.
Without this dependency, the driver probe was deferred:
[ 24.902331] platform mlxreg-hotplug: deferred probe pending: (reason unknown)
With kmod-i2c-mux-reg added, the probe succeeds and the expected
multiplexed I²C buses are registered:
[ 15.793884] i2c i2c-1: Added multiplexed i2c bus 2
[ 15.799391] i2c i2c-1: Added multiplexed i2c bus 3
[ 15.804830] i2c i2c-1: Added multiplexed i2c bus 4
...
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/20274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a typo on defining the PHY package kmod description that reference
phy-aeonsemi-as21x1x package instead of phy-aeonsemi-as21xxx.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
gpio pwm driver is only available on kernel 6.11+.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20187
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package the generic kernel PWM GPIO driver as module to avoid the need
to build it into the kernel.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://github.com/openwrt/openwrt/pull/20160
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit add kernel module support for Infineon DPS310/DPS368/DPS422
digital barometric air pressure and temperature sensor.
Test on custom board based on Mediatek MT7988a.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20101
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
The EN751221 has an XHCI that is compatible with MT7621.
While there is setup logic in the vendor code for both
EN751221 and MT7621, but MT7621 does not use it in mainline
or OpenWRT, and it appears to work correctly with EN751221.
Include SCSI / Mass Storage because many EcoNet devices
contain a builtin USB SD-Card reader.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20050
[Remove usb storage kmod from smartfiber_xp8421-b]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds kernel packages for the Vitesse VSC73XX switches.
I have split the switch into explicit SPI and platform integrated
variants as it's quite a bit of code.
Link: https://github.com/openwrt/openwrt/pull/20057
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PKG_MAKE_FLAGS is required when compiling r8168-rss
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20001
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix probing and load correct drivers
when using last backports.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport support for Aeonsemi AS121xxx PHY. The PHY require dedicated
firmware to be loaded to correctly work and support a big family of
Aeonsemi PHY that provide from 1G to 10G speed.
Automatically refresh all affected patch and file (rtl PHY).
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Most drivers have this as const. Especially upstream in the kernel.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19911
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NILFS is a log-structured file system developed for Linux.
NILFS provides versioning capability of an entire file system
and continuous snapshotting that allows users to restore files
mistakenly overwritten or destroyed a while ago.
Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All of this uses OF now. No need to keep platform data around.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19804
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Texas Instruments BQ32000 I2C real-time clock chip.
Tested on a custom board based on Hi-Link HLK-7628N.
Signed-off-by: Ondrej Kolar <ondrej@kolarovo.cz>
Link: https://github.com/openwrt/openwrt/pull/19764
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The cdns3 driver can be built without usb host mode support. Fix
dependencies to handle the case it is built with only gadget support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Build DWC3 driver in the right mode:
- host mode if kernel have usb host support only.
- gadget mode if kernel have usbgadget support only.
- dual-role mode if kernel have both usb host and usbgadget support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The usb role driver does not depend on the kernel config CONFIG_USB (host
side support). It only depends on the kernel config CONFIG_USB_SUPPORT.
Now it depends on the OpenWrt configurations USB_SUPPORT or
USB_GADGET_SUPPORT (usb and usbgadget features). We can assume that if usb
or usbgadget features are set, CONFIG_USB_SUPPORT has been set in the
target/subtarget kernel config.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The usb gadget drivers don't depend on usb host support, so fix the package
dependencies accordingly.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move usb-common driver from usb-core package to a new usb-common package.
The usb-common driver is needed by usb-gadget driver which can be used
without host support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for building the ds2438 one-wire kernel module.
Signed-off-by: Andres Heinloo <andres@gfz.de>
Link: https://github.com/openwrt/openwrt/pull/19694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-sfc should add support for Solarflare SFC9000 series based cards.
However after kernel 5.19, support for the 'Siena' subclass of
SFN5000/6000 devices has been separated out since they went EOL as they
are no longer being actively developed. As kmod-sfc no longer provides
driver support for these cards and hasn't since kernel 5.2, a new kernel
module is needed to support these 10Gb Ethernet cards. More info here:
https://cateee.net/lkddb/web-lkddb/SFC_SIENA.html and here:
https://www.phoronix.com/news/Solarflare-SFC-Siena-Linux-5.19
The module can be compiled in separately and works if kernel is custom
compiled;
OpenWRT has made these changes already with the SFC 'falcon' subclass of
drivers already. See 3c5d70a and e5ba6e9
This is building on excellent work by @ynezz and @nasbdh9
Signed-off-by: Steve Wavler <trenchcoatjedi@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19647
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This will be used in the following commit to move MAC assignment of the
DSL interface to NVMEM.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17289
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds kernel module support for Microchip MCP342x family of I2C ADCs.
Tested on a custom board based on Hi-Link HLK-7628N.
Signed-off-by: Ondrej Kolar <ondrej@kolarovo.cz>
Link: https://github.com/openwrt/openwrt/pull/19619
Signed-off-by: Robert Marko <robimarko@gmail.com>
Estimate the tx throughput based on the expected per-packet tx time.
This is useful for mesh implementations that rely on expected throughput,
e.g. 802.11s or batman-adv.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Select the kmod-drm-display-helper package instead of depending on it.
kmod-drm-display-helper is hidden now, so the user can not manually
select it.
This fixes the build of the imx target.
Fixes: 8bcc6d1894 ("kernel: kmod-drm-display-helper: Mark hidden")
Link: https://github.com/openwrt/openwrt/pull/19532
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-crypto-lib-aescfb is marked hidden and not selected by any other
package, it can not be build.
The Kconfig option in the kernel has no title, so it can not be
selected, it is only selected by CONFIG_TCG_TPM2_HMAC in the kernel.
Fixes: ef2310b031 ("kernel: modules: update dependency for kmod-tpm")
Fixes: aa51a1c13a ("kernel: kmod-crypto-lib-aescfb: Mark hidden")
Link: https://github.com/openwrt/openwrt/pull/19532
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nfs_layout_flexfiles.ko and nfs_layout_nfsv41_files.ko file are
build automatically when CONFIG_NFS_V4_1 is selected, we can not
deactivate them. Pack them into the NFS package too. I do not know if we
should also load them automatically.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_B53 kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-dsa-b53 depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_BCMGENET kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-bcmgenet depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_PARMAN has no title and can not be
directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_OBJAGG has no title and can not be
directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_DRM_DISPLAY_HELPER has no title and can
not be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_DRM_BUDDY has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_V4L2_ASYNC has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_V4L2_FWNODE has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_CRYPTO_LIB_AESCFB has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_CRYPTO_ENGINE has no title and can not
be directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Kernel config option CONFIG_IIO_BACKEND has no title and can not be
directly selected. Do the same for this kmod and make it hidden.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel driver configuration depends on PINCTRL.
Show this driver only on targets supporting pinctrl.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These drivers depend on the kernel option CONFIG_PWM, only add them to
OpenWrt for targets which have PWM support.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel driver configuration depends on ath79 or compile test and not
on PCI. Allow this package in OpenWrt only for the ath79 target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DRM modules for simple (ie. raw, non-eDP) panels can be used also
by platforms others than Freescale i.MX.
Create an individual package for it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Package kernel modules for PS/2 mouse support, mostly to allow
using touchpads and trackpoints built-into laptops (many of those
are connected using classic i8052-compatible PS/2 I/O).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buildbot revealed that on the x86/geode target, on which CONFIG_DRM=y isn't set,
kmod-i2c-hid misses the dependency on kmod-drm. Fix that to fix the build for
x86/geode.
Fixes: c83e275c9b ("kernel: package modules for I2C HID devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package driver modules for I2C HID devices such as touchpads,
touchscreens and trackpoints found on some laptops. Only the ACPI
firmware variant of the driver is packaged for now as that's what I got
for testing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The number of serial interfaces for the chip 8250 can be configured at
build time. This is currently not configurable and is always set to 16
interfaces. This is too little for some small embedded devices and too much
for others (x86_64). Therefore, this commit creates the possibility to set
this at compile time.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/19217
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allows to enable/disable attached regulators from userspace, i.e. by
simply writing value to a sysfs exported state file. Useful in case of
USB port VBUS toggled by GPIO.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6df761e0e6c7 mt76: fix signature of platform_driver remove funtions for newer kernels
5724be1a6b12 wifi: mt76: Replace strlcpy() with strscpy()
c4a114e2b8c9 wifi: mt76: fix queue assignment for deauth packets
243e572d89fc wifi: mt76: add a wrapper for wcid access with validation
e41c7785589f wifi: mac80211: get tx power per link
d70f62b8f1c7 wifi: mt76: fix vif link allocation
7b3cd3274a24 wifi: mt76: mt7996: Fix secondary link lookup in mt7996_mcu_sta_mld_setup_tlv()
cf89b6218043 wifi: mt76: mt7996: Rely on for_each_sta_active_link() in mt7996_mcu_sta_mld_setup_tlv()
d71108eedab1 wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()
32f8c5849ed1 wifi: mt76: mt7996: Fix mlink lookup in mt7996_tx_prepare_skb
ffff9f71e29d wifi: mt76: mt7996: Fix possible OOB access in mt7996_tx()
afe63e758196 wifi: mt76: mt7996: Fix valid_links bitmask in mt7996_mac_sta_{add,remove}
68dd28b99dad wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()
293778652452 wifi: mt76: mt7996: Move num_sta accounting in mt7996_mac_sta_{add,remove}_links
a94166b21e20 wifi: mt76: Get rid of dma_sync_single_for_device() for MMIO devices
87873d854e51 wifi: mt76: mt7925: Fix null-ptr-deref in mt7925_thermal_init()
06ba3d5e91f4 wifi: mt76: mt792x: Limit the concurrent STA and SoftAP to operate on the same channel
b9f4e0df317d wifi: mt76: mt792x: improve monitor interface handling
ec95319fd3fb wifi: mt76: mt7921s: Introduce SDIO WiFi/BT combo module card reset
dd2d862251cb firmware: add missing mt7990 eeprom files
05eaa56bc7a4 firmware: update mt7992 firmware to 20250328
32ca2b6db354 firmware: update mt7996 firmware to 20250328
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k ahb patch was updated to match the latest upstream version,
however the openwrt DT files still use the older names.
Add those as extra entries in order to remain compatible until DT files
are fixed.
Fixes: 88f4c32060 ("mac80211: update to version 6.14.11")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This will allow more flexibility in using PHY drivers as kmods.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Maxlinear GPHY module. Also add support for
kmod-polynomial, which is a dependency for this module.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the development history of Intel's drivers, the i40evf driver was later
renamed the iavf driver. For example, some documents mention that
Intel® Network Connections Software Version 24.0 renamed the i40evf
and ixlv drivers to iavf. In subsequent versions, the i40evf driver was
gradually removed, and its functions were taken over by the iavf driver.
In the Linux system, relevant configuration instructions also exist. For
instance, the User Guide for X722 Onboard Network Card states that the
i40evf driver module should be disabled, and the iavf driver should be
installed and used.
blamed commit: 5d81b28a82
Signed-off-by: xiao bo <peterwillcn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19197
Signed-off-by: Robert Marko <robimarko@gmail.com>
The stm32-dfsdm-adc module depends on it (kernel 6.12).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18740
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The memory mapped TPM interface (TIS) can be used for
emulated or virtualized TPM instances with QEMU and
a simulation package like swtpm.
On QEMU the device will appear in the device tree
with a "tcg,tpm-tis-mmio" compatible.
For example:
qemu-system-aarch64 -machine virt -cpu max \
-bios u-boot.bin \
-nographic \
.... \
-hda openwrt-armsr-armv8-combined-efi.img \
-chardev socket,id=chrtpm,path=/tmp/mytpm/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-device,tpmdev=tpm0
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/19188
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change deprecated function strlcpy to strscpy
for compatibility with kernel 6.12.
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
Direct replacement is safe here since DEV_ASSIGN is only used by
TRACE macros and the return values are ignored.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport accepted BCM5325 patches from net-next.
These patches will be merged in the v6.17 kernel window.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
QCN6122 wifi in fw-memory-mode 1 has a slightly larger caldb size than
currently defined in the ath11k driver. When coldboot calibration was
disabled, the fw mem mode was changed from 2 (256MB mem profile) to 1
(512MB mem profile), which is the correct setting for devices in scope.
However, in fw mem mode, the caldb size is 0x500000 instead of the max
0x480000 defined in the driver, causing QCN6122 wifi failing to boot:
ath11k b00a040.wifi1: qmi mem size is low to load caldata
ath11k b00a040.wifi1: failed to assign qmi target memory: -22
As such, change the max caldb memory size accordingly.
This macro is used by the driver only as a max size limit to validate
the requested caldb size returned by QMI. Different ath11k wifi chips
have different caldb sizes (for ex. the size for IPQ5018 is 0x200000).
Fixes: cf715a2305 ("wifi: ath11k: disable coldboot calibration for ipq5018")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove upstream backport patch.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19100
Signed-off-by: Robert Marko <robimarko@gmail.com>
Coldboot calibration does not work causes the firmware to crash during
wifi startup. So let's disable coldboot calibration until a solution is
found.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19083
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add new setting CONFIG_NET_DSA_REALTEK_RTL8366RB_LEDS which
was introduced in kernel 6.12 and allows enabling LEDs for
the Realtek RTL8366RB subdriver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19048
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
building with CONFIG_ALL_KMODS unearthed all sorts of interesting
failures
ERROR: module 'crypto/chacha-x86_64.ko' is missing.
ERROR: module 'crypto/poly1305-x86_64.ko' is missing.
ERROR: module 'crypto/curve25519-x86_64.ko' is missing.
ERROR: module 'crypto/camellia-x86_64.ko' is missing.
These stem from the main UML Makefile.
|# UML only makes sense on linux
|ifeq ($(HOST_OS),Linux)
| ifeq ($(HOST_ARCH),x86_64)
|
|ARCH:=x86_64
|BOARD:=uml
The modules in question define x86_64 optimized version and
the OpenWrt's buildsystem expects that these modules will be present.
SPI is not available due to the UML Architecture not setting HAS_IOMEM.
In the future, UML could get (virtualized) IOMEM and/or SPI could drop
the HAS_IOMEM dependency. A patch for the latter has been sent:
<https://lore.kernel.org/linux-spi/20250530234941.950431-1-chunkeey@gmail.com/T/#u>
mt76: Unfortunately, the firmware packages are picked up, but the
associated drivers can't be build because iowrite32+ioread32 are
not defined.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds support for RTL8814AE/RTL8814AU PCI/USB adapters.
Run-tested: x86/64/rockchip
USB adapter tested: Hawking HW17ACU Wireless-AC1750.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19052
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux 6.8 changed the directory structure for the video-code driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
The original OF code effectively does a reset at ahb.c but then again in
hw.c. For AR9330, it's already done in the driver and with the others,
there are patches in here that do the same. hw.c looks like the proper
place to handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19031
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes ath9k on ar934x platforms.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19031
Signed-off-by: Robert Marko <robimarko@gmail.com>
Building against recent kernel versions (noticed with 6.12) and -Werror
can fail because a macro MAX(a,b) is already defined in minmax.h or
kernel.h before 5.10.
In file included from ../mwlwifi-2025.02.06~db97edf2/hif/fwcmd.h:23,
from ../mwlwifi-2025.02.06~db97edf2/core.c:25:
../mwlwifi-2025.02.06~db97edf2/hif/hostcmd.h:1124:9: error: "MAX" redefined [-Werror]
1124 | #define MAX(a, b) (((a) > (b)) ? (a) : (b))
| ^~~
In file included from usr/include/mac80211-backport/linux/minmax.h:4,
from ./include/linux/kernel.h:28,
from usr/include/mac80211-backport/linux/kernel.h:3,
from ./include/linux/skbuff.h:13,
from usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from usr/include/mac80211-backport/linux/etherdevice.h:3,
from ../mwlwifi-2025.02.06~db97edf2/core.c:18:
./include/linux/minmax.h:330:9: note: this is the location of the previous definition
330 | #define MAX(a,b) __cmp(max,a,b)
| ^~~
Add a pending upstream patch which replaces the MAX(a,b) macro to avoid
conflicts and allow compilation with 6.12
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/18980
Signed-off-by: Robert Marko <robimarko@gmail.com>
446db12b1fd3 MP: fix uniphy reset in phy to phy link scenario
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
3423fdacac63 ssdk_clk: Remove MP_PHY clocks resets and init logic
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
The initial 6.12 merge leaves package/zram menuconfig behaviour confusing.
Selecting "kmod-zram" opens a submenu of the available algorithms to build
and the actual algo to use. However, when "lzo-rle" is shown as the default
used, it still remains missing from the available list. Only enabling a
_different_ compression algo to build will also reveal "lzo-rle" as
available.
Update the Kconfig to show "lzo-rle" as available if used/referenced.
Fixes: 4708057e27 ("package/zram: update for kernel 6.12")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver tries to access ioports (0x2f9!!) which UML doesn't have.
This causes lots of warnings to appear on boot:
| WARNING: CPU: 0 PID: 1 at lib/logic_iomem.c:188 serial8250_config_port+0x20a/0x1260
| Invalid writeqb of 0xff at address 2f9
| Modules linked in:
| CPU: 0 UID: 0 PID: 1 Comm: swapper Tainted: G W 6.12.25 #0
| Tainted: [W]=WARN
| Stack:
| Call Trace:
| [<60001000>] ? set_reset_devices+0x0/0x16
| [<60452cba>] ? serial8250_config_port+0x20a/0x1260
| [<6071e91f>] ? dump_stack_lvl+0x55/0x71
| [<606e127c>] ? _printk+0x0/0x4f
| [<60044bbb>] ? __warn+0x11b/0x120
| [<6003b5d0>] ? um_set_signals+0x0/0x40
| [<606de721>] ? warn_slowpath_fmt+0x81/0x8c
| [<606de6a0>] ? warn_slowpath_fmt+0x0/0x8c
| [<60452cba>] ? serial8250_config_port+0x20a/0x1260
(they are even recursive!)
Now, the situation gets more confusing. Because from what I can tell,
this was seemingly done intenionally. Upstream patches in related areas:
|commit ddd268c42871b78c75e12a5c28207fb481138f41
|Author: Niklas Schnelle <schnelle@linux.ibm.com>
|Date: Wed Apr 3 14:43:00 2024 +0200
|
| um: Select HAS_IOREMAP for UML_IOMEM_EMULATION
|
| In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
| compile time. UML supports these via its UML_IOMEM_EMULATION so let that
| select HAS_IOPORT and also reflect this in NO_IOPORT_MAP.
hint that there's ongoing work in this area. But unfortunately, this future
hasn't arrived yet. Once this future arrives, please nuke this patch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, MaxLinear/Exar USB serial devices are supported via out-of-tree
usb-serial-xr_usb_serial_common driver which is broken on 6.12.
So since upstream has support for these devices since 6.5 lets package
the in-tree driver to be able to drop the out-of-tree one.
Link: https://github.com/openwrt/openwrt/pull/18926
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream seems to be using led-sources instead of custom properties.
Code mostly taken from mt76.
Changed all(few) users of qca,led_pin to use the new format.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18805
Signed-off-by: Robert Marko <robimarko@gmail.com>
After removing kernel 6.6 support for x86 targets,
kernel 6.12 conditions no longer need to be checked.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18848
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define define fb-io-fops module - Fbdev helpers for framebuffers in I/O memory
By creating a hidden module it is possible to load fb_io_fops.ko
according to the kernel version.
Fixes: 5048c9d ("kernel: modules: adjust the object files of kmod-fb ")
Package kmod-drm-radeon is missing dependencies for the following libraries:
fb_io_fops.ko
make[2]: *** [modules/video.mk:620: /__w/openwrt/openwrt/openwrt/bin/targets/x86/geode/packages/kmod-drm-radeon-6.12.28-r1.apk] Error 1
time: package/kernel/linux/compile#45.35#40.01#75.34
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18771
Signed-off-by: Robert Marko <robimarko@gmail.com>
rtw_ndev_notifier_call should ignore network devices created by other drivers, and it does so,
but when CONFIG_WIRELESS_EXT=n, it does not behave as expected.
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18801
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to current SSDK head for 6.12 compatibility.
We must disable warnings for missing declarations and prototypes since
whole SSDK is litered with them and actually fixing them is like doing
whack a mole.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add package for linux intel_vpu driver for Intel NPU/VPU
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/17904
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's the proper function to handle this stuff in.
The original patch abused the fact that the ath9k driver in init called
ath9k_init_platform to populate all the needed configuration. This is
the wrong place to do so and it also goes away in 6.13.
Move 553-ath9k_of_gpio_mask.patch contents to ath9k_of_init where they
belong.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18764
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adjust the 'inline' declaration order to fix the build warning:
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-adsl-mei-danube/ltq-adsl-mei/drv_mei_cpe.c:188:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
188 | static void inline MEI_MASK_AND_ACK_IRQ(int x)
| ^~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
fix inline declaration warning
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are a lot of missing-prototypes warnings, It's not worth to
fix them one by one. Let us just ignore them.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix incomplete type error by including the correct header.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
