FIPS 140-3 recommends that all crypto implementations should be tested
before first use. Testmanager performs initial tests based on existing
test vectors. Not all algorithms have defined test vectors, so to improve
this situation, this commit backports recently added test vectors for
following cipher suites:
* authenc(hmac(md5),cbc(des))
* authenc(hmac(md5),cbc(aes))
* authenc(hmac(sha1),rfc3686(ctr(aes)))
* authenc(hmac(sha224),rfc3686(ctr(aes)))
* authenc(hmac(sha256),rfc3686(ctr(aes)))
* authenc(hmac(sha384),rfc3686(ctr(aes)))
* authenc(hmac(sha512),rfc3686(ctr(aes)))
These vectors were calculated using a software implementation and then
double-checked on Mediatek MT7981/MT7986 (safexcel) and NXP P2020 (talitos).
Both platforms passed self-tests.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/22409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add pending patch for improving Huawei MA5671a SFP fixup, which allows
communicating with the module even if the fiber isn't connected.
Link: https://github.com/openwrt/openwrt/pull/22283
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Refresh kernel patches with make target/linux/refresh for each target.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
The single user of the downstream gpio-cascade driver has been switched
to use the upstream gpio-line-mux driver. Thus, we can drop the former
now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixed the compilation of kernel with the loadable modules support turned off
Signed-off-by: Maksim Dmitrichenko <dmitrmax@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22041
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh the patches to make them apply cleanly again.
Fixes: 105eb9ca95 ("kernel: add cake-mq support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Though most Macronix Flash support the lock feature, the generic lock
implementation is not fully compatible with the Macronix series Flash.
Enabling the lock feature globally is unsafe. These hack patches are
used to unlock the Flash of ubnt devices on the ath79 target. Rework
these patches and move it to the ath79 target to prevent the potential
risk.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This header is deprecated and typically platform_device.h should be
used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21164
[Adapted the lantiq patches a bit]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This introduces support for the SkyHigh S35ML-3 series SPI NAND flash
devices by importing two key patches:
- 430-v6.14-mtd-spinand-Introduce-a-way-to-avoid-raw-access.patch
- 431-v6.14-mtd-spinand-Add-support-for-SkyHigh-S35ML-3-family.patch
Additionally, refresh all existing patches.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Rongzeng Cai <cairongzeng@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bc-bocun Chen of MediaTek has discovered a memory leak in the error path
in our downstream patch for mtk_eth_soc which adds support for the 10G
PCS and PHY paths of the MT7988 SoC.
Fix this by freeing the at this point already allocated netdev resources
before returning the error.
Fixes: 4cb6bd9a6d ("mediatek: switch to pending XFI 10G Ethernet drivers")
Reported-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 7390e63374.
This broke SFP handling on some Mediatek SoCs.
Some SFPs are configured for inband/2500base-x link mode and were
rejected with this change.
Fixes: https://github.com/openwrt/openwrt/issues/21436
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a bunch of upstream commits simplifying the RealTek PHY driver
and re-unifying the C22 and C45 driver instances.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace downstream hack disabling SGMII in-band AN on the MediaTek platform
with pending upstream patch announcing in-band AN capabilities and implementing
configuring in-band AN in the PHY driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only use link-partner advertisement bits for 10GbE modes if they are
actually valid. Check LOCALOK and REMOTEOK bits and clear 10GbE modes
unless both of them are set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace downstream hack for RealTek PHYs with a more clean solution
which could make it upstream.
As SGMII in-band AN is broken on some platforms, or simply expected to
be disabled by default in phy/sgmii mode (ie. on-board PHYs with MDIO
for out-of-band configuration and status), a hack for the RealTek PHY
driver was introduced to unconditionally disable SGMII in-band
autonegotiation.
Meanwhile the kernel has gained a proper interface for PHY and PCS to
report in-band AN capabilities and enable/disable in-band, matching
PHY and PCS capabilities.
Thanks to Bevan Weiss' knowledge about how RealTek PHY SerDes registers
are being handled in RealTek's SDK this can now be greatly improved:
- report in-band capabilties
- let phylink set in-band matching PCS and PHY capabilities
- properly abstracted indirect access of SerDes registers
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
RealTek's 2.5G PHYs suffer from an up to now inexplicable problem which
results in the SerDes mode not being properly setup and disabling
in-band AN leading to a timeout waiting for a busy-bit to clear. Up to
now there has been a crude work-around: resetting the PHY and trying
another time.
The cause has now been found as a wrong access to register PHYCR1 on
MDIO_MMD_VEND1 instead of MDIO_MMD_VEND2 when setting up ALDPS as well
as disabling the MDIO broadcast address 0.
In order to access MDIO_MMD_VEND2 on Clause-22-only busses a custom
.read_mmd and .write_mmd ops are implemented, mapping MDIO_MMD_VEND2 to
paged access as this is required.
Also, as ALDPS by design disables the SerDes PCS of the PHY in case the
link has been down for a while, move enabling ALDPS to the end of the
config_init function to not face problems when configuring the interface
mode and in-band AN.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The first two patches are providing function needed by the last patch.
Fixes: 813ecda1f3 ("generic: backport phylink patches for PCS/PHY caps OPs")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
Fixes: 48c9e55094 ("kernel: backport upstream Realtek PHY patches")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The function phy_id_compare_vendor() is needed by the fix.
Refresh 782-05-v6.16-net-phy-Add-support-for-Aeonsemi-AS21xxx-PHYs.patch with the upstream code.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
Fixes: 813ecda1f3 ("generic: backport phylink patches for PCS/PHY caps OPs")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These formally pending patches were merged into upstream Linux some time
ago. Move them to the backports folder and add the kernel version they
were added to the file name.
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace pending patches which are already integrated in upstream Linux
with their upstream versions.
These patches were exported with:
git format-patch -1 -k
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add opending patch fixing resource_size(9 if resource start and end is
set to zero.
This is to indirectly fix a helper rework in ath11k qmi code that cause
firmware load panic.
Link: https://github.com/openwrt/openwrt/pull/20964
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since everything got migrated to the layouts driver, this is no longer
needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20948
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport of the latest upstream Realtek PHY patches. WoL uses
devm_pm_set_wake_irq(), so the patch that adds this function
has also been backported.
Changelog:
4465ae435ddc net: phy: realtek: create rtl8211f_config_phy_eee() helper
bb78b71faf60 net: phy: realtek: eliminate priv->phycr1 variable
e1a31c41bef6 net: phy: realtek: allow CLKOUT to be disabled on RTL8211F(D)(I)-VD-CG
910ac7bfb1af net: phy: realtek: eliminate has_phycr2 variable
27033d069177 net: phy: realtek: eliminate priv->phycr2 variable
8e982441ba60 net: phy: realtek: create rtl8211f_config_rgmii_delay()
b826bf795564 net: phy: realtek: fix RTL8211F wake-on-lan support
Tested on Netgear WAX206 with RTL8221B-VB-CG.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20987
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
Link: https://github.com/openwrt/openwrt/pull/20962
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These patches fix the remaining issues with BCM5325 switches and allow
dropping the default VLAN on Huawei HG556a.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
