lantiq_gswip and tag_gswip were not loaded during failsafe, leaving the
switch uninitialised. This caused LAN1 port to show no link, making
SSH-based recovery impossible.
Add the autoload flag and include tag_gswip (which was also missing from
the autoload list) so the switch initialises correctly in failsafe mode.
Tested on BT HomeHub 5A (lantiq/xrx200).
Fixes: https://github.com/openwrt/openwrt/issues/22480
Signed-off-by: Benjamin Levine <benjaminmileslevine@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22514
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Release previously allocated memory and OF node before return.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22276
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devices use the binding + eeprom-swap. Turns out the reason swap
is needed is because the binding wrongly swaps the data on big endian
hosts. NVMEM doesn't do this and thus just works.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22207
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MIPS code assigns the clock node based on the device tree node name.
This name was renamed with kernel 6.12.58 and v6.6.117. Adapt our out of
tree device tree files to this rename to fix loading the STP GPIO
driver.
Without this fix the driver fails like this:
```
[ 0.320000] gpio-stp-xway 1e100bb0.stp: Failed to get clock
[ 0.330000] gpio-stp-xway 1e100bb0.stp: probe with driver gpio-stp-xway failed with error -2
```
Link: https://git.kernel.org/linus/b0d04fe6a633ada2c7bc1b5ddd011cbd85961868
Fixes: https://github.com/openwrt/openwrt/issues/21697
Co-Authored-By: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22444
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device has 1 100MBit/s port. By default the PHY firmware is running
in 1GBit/s mode. The driver will try to load the 1GBit/s firmware and
fail if it is not there. Set the GPHY0 also to 100MBit/s mode.
The driver uses all nodes independent of the status attribute.
Do the same fix for AVM FRITZ!Box 7412 too.
Reported-by: Achelon in OpenWrt forum
Fixes: https://github.com/openwrt/openwrt/issues/21836
Link: https://github.com/openwrt/openwrt/pull/22188
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 9dbd45c187.
Compared to ralink,mtd-eeprom , the nvmewm binding ends up byteswapping
the data on big endian hosts. Meaning on big endian, the nvmwem binding
is equivalent to:
ralink,mtd-eeprom +
ralink,eeprom-wrap
Revert as a result since there's no eeprom-swap here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22192
Signed-off-by: Robert Marko <robimarko@gmail.com>
If nvmem is used for ethernet mac address, we need to defer loading to
get the proper mac.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21955
Signed-off-by: Robert Marko <robimarko@gmail.com>
The xrx200 ethernet driver falls back to a random MAC address on any
error from of_get_ethdev_address(), including -EPROBE_DEFER. When the
MAC address comes from an nvmem layout driver (such as u-boot-env on
NAND), the nvmem cell may not be available yet at first probe attempt.
Fix this by propagating EPROBE_DEFER so the driver probe is deferred
until the nvmem cell becomes available.
Tested on Zyxel P-2812HNU-F1 (NAND, u-boot-env nvmem layout).
Signed-off-by: Burak Aydos <byhexadecimal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This header is deprecated and typically platform_device.h should be
used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21164
[Adapted the lantiq patches a bit]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The u-boot-env partition on the Zyxel P-2812HNU-F1 is 128 KiB but
the actual environment data is only 8 KiB (0x2000 bytes). Without
the env-size property, the u-boot,env nvmem layout driver assumes
env-size equals the full partition size and computes an incorrect
CRC32 over the entire 128 KiB, causing all nvmem cell reads to fail
silently.
Add env-size = <0x2000> so the CRC32 is computed over the correct
8 KiB region, allowing nvmem-cells (such as ethaddr) to be read
properly by the kernel.
Signed-off-by: Burak Aydos <byhexadecimal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21780
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the original userspace implementation, the WAN and DSL interfaces
used the same MAC. Mirror that here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21081
Signed-off-by: Robert Marko <robimarko@gmail.com>
The vr9.dtsi configures the GPIO 38 as reset GPIO. Also the fon LED is
configured on GPIO 38. This conflicts and makes the probing of the PCIe
controller fail in OpenWrt 25.12.
The AVM GPL source code configured GPIO 21 as PCIe reset.
Fixes: https://github.com/openwrt/openwrt/issues/21562
Link: https://github.com/openwrt/openwrt/pull/21641
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit ab805ec316 ("generic: add missing squashfs config") enabled
CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU in the generic config, so it is no
longer needed in the target configs.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21465
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rename them to follow the rtl836x driver gpiod changes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21143
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoids having to create a custom LED for wifi.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that NVMEM in UBI is supported, more handling can be moved.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
node name matches various comments about the pci path.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20522
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel update commit also changed the name of the dtsi node. Adapt
the other dts files.
Fixes: 738876e76b ("kernel: bump 6.12 to 6.12.58")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add pending patch to address PCI sysfs creation entry race observed on
ipq806x. This is to handle a kernel warning on creating the same sysfs
entry multiple times.
All affected patch automatically refreshed.
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The latter is more descriptive in terms of what's going on.
Mostly found with
git grep gpios\ | grep 0\>
git grep gpios\ | grep 1\>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated. Fixes dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
Most drivers have this as const. Especially upstream in the kernel.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19911
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patches 12 and 13 have been superseded by patch 12. Other patches
have no significant changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19675
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling of both calibration and mac addresses is deprecated.
Also fixed calibration size for ath9k. AR9287 uses 3d8 for its size.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17289
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 6.12 is now default, drop 6.6 support.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19682
Signed-off-by: Nick Hainke <vincent@systemli.org>
Let's switch the lantiq target to use kernel 6.12 by default.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19682
Signed-off-by: Nick Hainke <vincent@systemli.org>
All kernel symbols are automatically refreshed by
`make kernel_oldconfig CONFIG_TARGET=target` and
`make kernel_oldconfig CONFIG_TARGET=subtarget`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
* Drop obsolete flag I2C_CLASS_SPD. [1]
* Change .remove callback return type to NULL.
* Use strscpy instead of strlcpy.
This patch fixes the following build errors:
drivers/i2c/busses/i2c-lantiq.c:599:41: error: 'I2C_CLASS_SPD' undeclared (first use in this function); did you mean 'I2C_CLASS_HWMON'?
599 | adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
| ^~~~~~~~~~~~~
| I2C_CLASS_HWMON
drivers/i2c/busses/i2c-lantiq.c:600:9: error: implicit declaration of function 'strlcpy'; did you mean 'strncpy'? [-Wimplicit-function-declaration]
600 | strlcpy(adap->name, DRV_NAME "-adapter", sizeof(adap->name));
| ^~~~~~~
| strncpy
drivers/i2c/busses/i2c-lantiq.c:729:19: error: initialization of 'void (*)(struct platform_device *)' from incompatible pointer type 'int (*)(struct platform_device *)' [-Wincompatible-pointer-types]
729 | .remove = ltq_i2c_remove,
|
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.12.y&id=e61bcf42d290e73025bab38e0e55a5586c2d8ad5
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This is a preparation for 6.12 kernel support. It can help us
track the files history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This is a preparation for introducing the 6.12 kernel support.
All configs are automatically refreshed.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/lantiq/xway/vmmc.c:31:14: error: no previous prototype for 'ltq_get_mps_ad0_irq' [-Werror=missing-prototypes]
31 | unsigned int ltq_get_mps_ad0_irq(void)
| ^~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/vmmc.c:40:14: error: no previous prototype for 'ltq_get_mps_ad1_irq' [-Werror=missing-prototypes]
40 | unsigned int ltq_get_mps_ad1_irq(void)
| ^~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/vmmc.c:49:14: error: no previous prototype for 'ltq_get_mps_vc_irq' [-Werror=missing-prototypes]
49 | unsigned int ltq_get_mps_vc_irq(int idx)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/pci/ifxmips_pcie.c:1084:36: error: invalid use of undefined type 'struct platform_device'
1084 | struct device_node *node = pdev->dev.of_node;
| ^~
arch/mips/pci/ifxmips_pcie.c:1204:12: error: no previous prototype for 'ifx_pcie_bios_init' [-Werror=missing-prototypes]
1204 | int __init ifx_pcie_bios_init(void)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/lantiq/xway/ath5k_eep.c:34:12: error: no previous prototype for 'of_ath5k_eeprom_probe' [-Werror=missing-prototypes]
34 | int __init of_ath5k_eeprom_probe(struct platform_device *pdev)
| ^~~~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/eth_mac.c:15:11: error: no previous prototype for 'ltq_get_eth_mac' [-Werror=missing-prototypes]
15 | const u8* ltq_get_eth_mac(void)
| ^~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/lantiq/xway/timer.c:160:14: error: no previous prototype for 'ltq_get_fpi_bus_clock' [-Werror=missing-prototypes]
160 | unsigned int ltq_get_fpi_bus_clock(int fpi) {
| ^~~~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/timer.c:803:36: error: invalid use of undefined type 'struct platform_device'
803 | ret = devm_mutex_init(&pdev->dev, &timer_dev.gptu_mutex);
| ^~
arch/mips/lantiq/xway/timer.c:864:12: error: no previous prototype for 'lq_gptu_init' [-Werror=missing-prototypes]
864 | int __init lq_gptu_init(void)
| ^~~~~~~~~~~~
arch/mips/lantiq/xway/timer.c:873:13: error: no previous prototype for 'lq_gptu_exit' [-Werror=missing-prototypes]
873 | void __exit lq_gptu_exit(void)
| ^~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
