Reuse Device/FitImage recipe instead of open coding it and
drop duplicate KERNEL_INITRAMFS recipe for eDPU.
While at it, lets clean up the boot script to drop uneeded console
setting, earlycon etc.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add dependencies for Turris MOX board modules directly as
DEVICE_PACKAGES. (So that users don't have to add them manually.)
The device uses an SD card for primary storage so space shouldn't be an
issue.
Signed-off-by: Tomáš Macholda <tomas.macholda@nic.cz>
Link: https://github.com/openwrt/openwrt/pull/21151
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RIPE Atlas Probe v5 is a network measurement device based on Turris MOX.
u-boot bootscript supports booting both from the original Turris BTRFS
layout and default OpenWrt ext4 boot + root partition layout.
Specifications:
* SoC: Marvell ARMADA 3720
* RAM: 512 MiB, DDR3
* eMMC: 4G
* Ethernet: 1x 1GbE
MAC:
LAN MAC: label on board
Flash instructions:
* For using the default ext4 layout, boot into a live system using
tftpboot in u-boot and flash an OpenWrt SD image onto /dev/mmcblk0.
* For the Turris layout, put the new rootfs into subvolume '@', not
forgetting to add Image, device tree, and boot.scr to /boot.
Misc:
* USB connection is only for power. For UART access use the pin header:
1: GND
2: +1.8V
5: TX
6: RX
* Flashing the image onto Turris Shield won't work. Use Turris MOX image
instead.
Signed-off-by: Tomáš Macholda <tomas.macholda@nic.cz>
Link: https://github.com/openwrt/openwrt/pull/20031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the added support for generating per device targz rootfs so that images
generated for Methode devices when CONFIG_TARGET_MULTI_PROFILE and
CONFIG_TARGET_PER_DEVICE_ROOTFS are set, we actually get the targz rootfs
that respects DEVICE_PACKAGES.
Currently, buildbot generated images have no networking, LM75 nor I2C
working, as the generated images do not include required kmods that are
listed in DEVICE_PACKAGES.
While at it, there is no need for tar to run in verbose mode.
Fixes: 7dff6a8c89 ("mvebu: uDPU: add sysupgrade support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Adds support for Turris MOX, a modular router extendable by board modules (MOX B-G).
You can explore the idea behind the modules at: https://mox-configurator.turris.cz/
More information about Turris MOX can be found here: https://docs.turris.cz/hw/mox/intro/
Also works with Turris Shield (Turris MOX A and C with a simplified OS UI).
Specifications:
-----------------------
MOX A
- SoC: Marvell Armada 3720
- RAM: 512/1024 MB, DDR3
- Memory:
- 8 MB SPI NOR Flash for U-Boot and rescue system
- SD card slot
- 1x RJ-45, 1Gbps
- 1x USB 3.0
- 1x activity LED
- 1x reset button
- SDIO header
- misc pin header (UART, GPIO, JTAG, ...)
MOX B, G
- 1x mPCIe slot
- 1x SIM slot
MOX C
- 4x RJ-45, 1Gbps
MOX D
- SFP, 2.5Gbps
MOX E
- 8x RJ-45, 1Gbps
MOX F
- 4x USB 3.0
Module support:
-----------------------
Additional packages are needed for some modules.
MOX A (core)
- works as is
MOX B, G (mPCIe, mPCIe passthrough)
- works as is
MOX C, E (4x, 8x RJ-45)
- kmod-dsa
- kmod-dsa-mv88e6xxx
MOX D (SFP)
- kmod-sfp
- kmod-phy-marvell-10g
MOX F (4x USB 3.0)
- works as is
Wi-Fi 5, 3x3 card (WLE900VX)
- kmod-ath10k
- ath10k-board-qca988x
- ath10k-firmware-qca988x
Wi-Fi 6, DBDC, 2x2 card (MT7915DAN)
- kmod-mt7915e
- kmod-mt7915-firmware
Interface naming:
-----------------------
- MOX A's RJ-45 is assigned to `eth0`.
- MOX C, E (4x, 8x RJ-45) are assigned to `lan<number>@eth1`
- If MOX D (SFP) is connected directly to MOX A, the resulting interface
is `eth1`. If it's connected through MOX E (8x RJ-45), the resulting
interface is `sfp@eth1`.
Quirks:
-----------------------
- MOX is sensitive to the order of connected modules. Verify that the
confguration is valid at: https://mox-configurator.turris.cz/
- `CONFIG_MOXTET` and `CONFIG_GPIO_MOXTET` need to be enabled in kernel
config. Moxtet is a bus protocol needed to discover and configure MOX
modules. It must be compiled into the kernel for the modules to work.
Though it's very small so it won't bloat up the kernel image.
Flashing instructions:
-----------------------
1. Download `openwrt-*-ext4-sdcard.img.gz` and `gunzip` it.
2. Insert an SD card and flash the image to it using dd:
dd if=openwrt-*-ext4-sdcard.img.gz of=/dev/mmcblk0 bs=4096 conv=fsync
3. Plug the SD card into MOX.
Troubleshooting:
-----------------------
- https://docs.turris.cz/hw/serial/#turris-mox
- https://docs.turris.cz/hw/mox/rescue-modes/
Signed-off-by: Tomáš Macholda <tomas.macholda@nic.cz>
Link: https://github.com/openwrt/openwrt/pull/20356
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
all espressobins have topaz switch as same soc, so it is safe to add
kmod-dsa-mv88e6xxx to all
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18161
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's possible to add the driver for the Marvell MV88E6xxx DSA
switches using a module package rather than to compile it into
the kernel. For affected devices this saves a bit of space,
typically the DSA core is 600 KB so this and some more is saved
for devices with no DSA switch.
When adding the packages I went over both the upstream DTS files
and the OpenWrt-specific DTS files and used grep 'marvell,mv88e6'
to find the devices using these switches.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250113-mv88e6xxx-modularize-v2-1-3064419615cd@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows booting from internal eMMC or SD card just changing the
U-Boot mmc_dev variable.
In particular, setting mmc_dev to 1 will result in booting from the SD card.
Setting the variable to 0 will result in internal eMMC boot (the default).
Should the variable be unset or an error condition occur while reading
from SD card, internal MMC booting will be tried.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Add support for Methode euroDPU which is based on uDPU but does not
have a second SFP cage, instead of which a Maxlinear G.hn IC is used.
PHY mode is set to 1000Base-X despite Maxlinear IC being capable of
2500Base-X since until 5.15 support for mvebu is available trying to use
2500Base-X will cause buffer overruns for which the fix is not easily
backportable.
Installation instructions:
1. Boot the FIT initramfs image (openwrt-mvebu-cortexa53-methode_edpu-initramfs.itb)
2. sysupgrade using the openwrt-mvebu-cortexa53-methode_edpu-firmware.tgz
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
We so far had two variables IMG_PREFIX and IMAGE_PREFIX with
different content. Since these names are obviously quite
confusing, this patch renames the latter to DEVICE_IMG_PREFIX,
as it's a device-dependent variable, while IMG_PREFIX is only
(sub)target-dependent.
For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as
that's a device-dependent variable as well.
Cc: Paul Spooren <mail@aparcar.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.
- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot
** Installation **
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/
Connect to the device UART via microUSB port on the back side and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb
Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.
Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware
Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:
- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If device recipe has specified DEVICE_DTS variable, the dtb is built
anyway by OpenWrt buildroot image rules. Drop the patch and adjust the
location of compiled dtb.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This device receipe selects bunch of packages which some are re-defined,
unnecessary or irrelevant. Clean them up, so only basic functionality
persist.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Align subtargets makefiles names to actual subtargets.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
