Allow to convert MAC adddresses for all devices to NVMEM in
the future.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22302
Signed-off-by: Robert Marko <robimarko@gmail.com>
This STC8 microcontroller is used on a range of Hasivo managed switches.
It typically performs some fan/thermal control, and also has some
discrete IO hanging off of it.
The fan/thermal control is still somewhat unknown at this stage, but the
LED / gpio control has been determined as being two I2C registers which
need to be written to with a 'typical' Hasivo 0x40 execute mask set, to
change values.
Rather than having this expose the LED functionality / thermal control
directly, just represent it as an mfd, with some configurable OR'ing of
an execute-bit to certain registers (execute-bit-regs). This way different
STC8 arrangements can hopefully be handled by devicetree configs rather
than needing new driver code.
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21578
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The downstream Realtek phy module is currently known as rtl83xx-phy.c
and its kernel config REALTEK_SOC_PHY. It has been simplified, cleaned
and now aligns to Realtek main module (upstream Realtek phy). It is no
longer tied to the Realtek switch SoC but serves as generic module for
1Gbit multiport phys. Adapt it as follows:
- place it into the realtek folder aside its upstream sibling
- rename it to realtek_multiport.c
- remove SoC dependency in Kconfig and Makefile
- change kernel configs for the targets accordingly
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21929
Signed-off-by: Robert Marko <robimarko@gmail.com>
DSA tagging currently works with a tuned trailer tagging. That means:
- realtek target uses tag_trailer for tagging
- there is a patch for the trailer tagger to write the target port not
as a bitfield but as an integer
Make the tagging independent from upstream and hacky patches by providing
a new downstream driver. This can be aligned easier for future development.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ab805ec316 ("generic: add missing squashfs config") enabled
CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU in the generic config, so it is no
longer needed in the target configs.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21465
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GS1920-24HPv1 is a switch with 24 copper ports and 4 combo SFP/copper
ports and PoE on the first 24 ports.
Specifications:
---------------
* SoC: Realtek RTL8292M
* Flash: 16 MiB SPI flash
* RAM: 128 MiB
* Ethernet: 24x 10/100/1000 Mbps
* Buttons: 1x "Reset" button
* UART: 1x serial header, standard DCE pinout (Tx = 2, Rx = 3, Gnd = 5);
9600 baud, 8n1, +- 5.6V logic levels
* SFP: 4 combo copper/SFP ports
* PoE: 24x
* Fans: ADT7468 fan controller
Works:
------
- (24) RJ-45 ethernet ports
- Switch functions
- Buttons
- LEDs (partial support, the wrong LEDs light up)
- Manual fan control
Not yet enabled:
----------------
- PoE (requires patches to realtek-poe to support i2c)
- Combo ports (link is up, but no data is transferred)
Fans:
-----
After boot, the fans are running in full speed mode. You can interact
with the fan controller at /sys/class/hwmon/
Installation:
-------------
This device uses ZyNOS instead of Linux, this makes installation a bit
more cumbersome. Serial console is required!
1. Set the switch to boot from the first image. This step is crucial,
it will fail to boot if this is not set properly.
2. Connect to the switch using serial and interrupt the boot process
to enter debug/recovery mode.
3. Load the OpenWrt initramfs image via XMODEM. You need to obtain an
unlock code, based on your MAC address, first. See the excellent write
up at https://www.ixo.de/info/zyxel_uclinux/ for details. Replace
unlock_code in the commands below by the code obtained.
After running ATBA5, the terminal needs to be closed and re-opened
with 115200 baud. This speeds up the file transfer significantly!
The file length in bytes need to be given instead of file_length below.
You also need an XMODEM upload utility like "lrzsz-sx -X" to transfer
the file. Start the XMODEM upload after running the ATUPxxxx command:
> ATEN1,unlock_code
> ATBA5
> ATUP80100000,file_length
> ATGO80100000
4. Wait for OpenWrt to boot. Once this is done, transfer the loader binary
and the sysupgrade image to "/tmp" using scp.
5. Install OpenWrt permanently by running the following two commands on
the switch (over SSH):
> mtd write /tmp/loader.bin loader
> mtd write /tmp/sysupgrade.bin firmware
6. Reboot the switch and enjoy OpenWrt.
NB: You do not need to touch the loader binary unless it's recommended.
The loader is not part of a regular sysupgrade file and will be left
untouched. The boot loader only checks if the loader is valid to be
able to boot.
Recovery/ Return to stock:
--------------------------
Just spam the "u" key during (or "z" for 9600 baud) during memory testing
to trigger a recovery XMODEM upload at 115200 baud. A standard OEM upgrade
image works properly.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/20439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
L3 Offloading caused DHCP packets to be dropped at hardware level
And potentially buggy route implementation can cause a crash
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20208
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream will get support for the Realtek ECC engine with 6.18.
To make use of this in Openwrt
- backport upstream patches
- change config so that ECC will be built for nand subtargets
- define ECC engine in RTL93xx DTS.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19746
Signed-off-by: Robert Marko <robimarko@gmail.com>
Until now the the SerDes configuration is realized with helper functions
scattered around the DSA and PHY driver. Give them a new home as a PCS
driver.
The target design is as follows:
- dsa driver manages switch
- pcs driver manages SerDes on high level (this commit)
- mdio driver manages SerDes on low level
This driver adds the high level SerDes access via PCS. It makes use of
the low level mdio SerDes driver to access the registers.
Remark: This initial version provides exactly all phylink_pcs_ops that
are currently part of the DSA driver. So this can be swapped in one of
the next commits as a drop in replacement. To make use of it something
like this is needed:
...
ports = of_get_child_by_name(node, "ethernet-ports");
if (!ports)
return -EINVAL;
for_each_available_child_of_node(ports, port) {
pcs_node = of_parse_phandle(port, "pcs-handle", 0);
of_property_read_u32(port, "reg", &port_nr)) {
priv->pcs[port_nr] = rtpcs_create(dev, pcs_node, port_nr);
}
...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20075
Signed-off-by: Robert Marko <robimarko@gmail.com>
Until now the SerDes access is realized with some helper functions
in the mdio bus. These were moved around a lot and had no real home.
End that temporary solution to move them where they belong.
The target design for the different Realtek drivers is as follows:
- dsa driver manages switch
- pcs driver manages SerDes on high level (to be developed)
- mdio driver manages SerDes on low level (this commit)
This driver adds the low level SerDes access via mdio. For debugging
purposes the user can interact with the SerDes in different ways.
First, there is a debug interface in
/sys/kernel/debug/realtek_otto_serdes/serdes.X/registers.
With that a dump of all registers can be shown.
> cat /sys/kernel/debug/realtek_otto_serdes/serdes.4/registers
Back SDS 4: 00 01 02 03 04 05 06 07 08
SDS : 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248
SDS_EXT : 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA
...
Second, one can read/write registers via the mmd functions of the
mdio command line tool. Important to know: The registers are accessed
on the vendor specific MDIO_MMD_VEND1 device address (=30). Additionally
the SerDes page and register are concatenated into the the mmd register.
Top 8 bits are SerDes page and bottom 8 bits are SerDEs register.
E.g.
- mmd 0x0206 : SerDes page 0x02, SerDes register 0x06
- mmd 0x041f : SerDes page 0x04, SerDes register 0x1f
Read register 0x02 on page 0x03 of SerDes 0
> mdio realtek-serdes-mdio mmd 0:30 raw 0x0302
Write register 0x12 on page 0x02 of SerDes 1
> mdio realtek-serdes-mdio mmd 1:30 raw 0x0212 0x2222
For now this driver is only defined in the devicetree and activated
in the kernel build. There is no current consumer but at least
the debugging interface is available. Cleanup of the currently used
SerDes functions will come later.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20062
Signed-off-by: Robert Marko <robimarko@gmail.com>
So much code was distributed between phy/ethernet/dsa drivers. A lot
was already cleand up before. With this step the mdio bus gets its
own space and is no longer hidden inside the ethernet driver.
This commit is mostly a copy/paste that includes only minor changes.
- define prefixes are renamed to RTMDIO
- The driver is totally self contained (does not rely on SoC include)
- The DTS structure (mdio node below ethernet node) was kept
- The driver is added to the kernel config of all subtargets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19942
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL93xx devices have a NAND controller built in. Upstream already
has a driver in place. Include it downstream. Activate it in the
RTL93xx builds and disable it for the RTL83xx builds.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19583
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove all files etc. for 6.6 because 6.12 is default now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19139
Signed-off-by: Robert Marko <robimarko@gmail.com>
Run this script:
./scripts/kconfig-reorder.sh
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/19200
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently only RTL83xx devices are known with shared SCL pins.
So activate the driver only for those targets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18737
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Extends SoC thermal sensor on rtl839x
* Tested on HP JG928A
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Link: https://github.com/openwrt/openwrt/pull/18825
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit d7e82c78d7 added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
realtek target.
Fixes: d7e82c78d7 ("generic: backport Realtek PHY patches from upstream")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The old RTL8231 driver integrated the MDIO bus access with the GPIO
control ops, making this driver not very portable to newer platforms.
It depended on the SoC ID instead of the compatible to determine the
MDIO access register, further complicating portability.
A new MFD driver is now available, which offers proper pin config as
well as optional LED support, which can work on any (bitbanged) MDIO
bus. Now that all devices have been migrated, we can drop the old code.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enable the RTL8231 MFD core driver, as well as the pinctrl/gpio driver
to allow RTL839x devices to use it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enable the driver for the Realtek Otto auxiliary MDIO driver so RTL839x
devices can use it. The related node is added to the base devicetree for
rtl839x-based devices, so they can enabled and use it when required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add pending patches to add RTL8231 support as a MDIO-bus attached
multi-functional device. This includes subdrivers for the pincontrol and
GPIO features, as well as the LED matrix support.
Leave the drivers disabled until required by a device.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add a driver that exposes the auxiliary busses, used for the RTL8231
expanders, as a proper MDIO controller. The device must be instantiated
under an MFD device, so the driver should also be compatible with SoC
managed by an external CPU via SPI.
Leave the driver disabled in builds until required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Run 'make kernel_oldconfig' to get an up-to-date config.
"# CONFIG_I2C_MUX_RTL9300 is not set" is retained, as the kernel module
build will selects CONFIG_I2C_MUX=m, on which this symbol depends.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Since the start of the Realtek target OpenWrt works with RTL83XX as the
target architecture. Upstream is using MACH_REALTEK_RTL instead. To
simplify further development align that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware information:
---------------------
- SoC: RTL8393M
- Copper phy: 6×RTL8218B
- Fibre phy: RTL8214FC
- Flash: 32MiB SPI NOR, MX25L25635FMI
- RAM: 128MiB DDR3, Micron MT41K64M16TW-107
- Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible)
- +370W POE on JG928A model
Note: SFP ports currently non-functional due to missing support for
RTL8214FC on the RTL8393M target.
Updated for Linux 6.6 kernel.
Installation:
-------------
- Initial installation follows same process as HPE 1920-24G (JG924A)
- Based on prior work of Jan Hoffmann <jan@3e8.eu>
- Additional work by Andreas Böhler <dev@aboehler.at>
- PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be>
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Copy files and config from 5.15 kernel version. Because of the big version jump
leave out the patches for now so we can treat them individually later on.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The legacy (BSD) PTY support could open security problems in a system,
We do not need them in OpenWrt, deactivate this option in all targets.
Debian also deactivates this option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On the realtek target, the subtarget makefiles include a KERNEL_PATCHVER
setting, shadowing KERNEL_PATCHVER from target/linux/realtek/Makefile.
This makes the realtek target an exception in this regard, and makes
switching kernel version a bit bothersome. Remove the overrides so all
subtargets use the same kernel version.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Our current Makefiles a little bit messy and can be improved somewhat,
both in whitespace and in style.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Use the new timer driver for the RTL839X devices and remove the
no longer needed modules.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Make use the new clock driver for RTL838X and RTL839x target devices. Of course
we will enable their primary consumer (cpufreq-dt) too. To be careful just set
the default governor to userspace. As we rely on SRAM activate that module too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The system status LED on Panasonic Switch-M48eG PN28480K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove redundant target-level entries, noting that these settings will be
configured from "Kernel build options" of Kconfig.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[remove from new configs introduced after patch submission]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The RTL839X does not have an internal phy and thus does not need to have any
firmware as part of the kernel, especially not firmware for the RTL838X.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Selects the new CEVT timer for Realtek instead of the previous
timer driver. While we are at it, we explicitily state we do
not use the I2C driver of the RTL9300.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Set CONFIG_FORCE_MAX_ZONEORDER setting to 13 to allow larger
contiguous memory allocation for the DMA of the Ethernet
driver. Increase the number of entries in the RX ring
to 300 making use of the larger DMA region now possible for
receiveing packets.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
