gpio-button-hotplug skips buttons with button->irq set because it cannot
handle true interrupt-only gpio-keys descriptions. That check also skips
valid GPIO-backed buttons that provide a separate interrupt specifier, such
as the Meraki MX60 reset button.
Try to acquire the GPIO descriptor before deciding that an explicit-IRQ
button is unsupported. Continue to skip true interrupt-only buttons, and
make the IRQ setup and teardown paths ignore skipped entries.
Tested on: Cisco Meraki MX60. Reset button now works.
Fixes: 23845fa10b ("gpio-button-hotplug: do not error on interrupt attached keys")
Assisted-by: Codex:GPT-5.5
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23382
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
This module adds support for the Corsair Commander Pro and Corsair
Commander Pro (1000D) fan and temperature monitoring controllers.
Signed-off-by: Dee HY <dongfengweixiao@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/23465
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the upstream RealTek PHY driver is patched to support also
the new 5G and 10G PHYs we can start to phase-out the messy downstream
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The AddDepends/pse-pd helper appended kmod-pse-pd to DEPENDS without the
'+' prefix, making it a hard dependency rather than an auto-selecting one.
This breaks pulling any PSE controller driver (kmod-pse-pd692x0,
kmod-pse-si3474, kmod-pse-tps23881, kmod-pse-regulator, ...) in via a
device's DEVICE_PACKAGES: the kmod itself is auto-selected, but the
unsatisfied hard dep on kmod-pse-pd silently drops it from .config.
Prefix the kmod-pse-pd entry with '+' so it auto-selects, matching how
the other deps in the same file (kmod-i2c-core, etc.) are expressed. The
helper is the right place to fix this; every PSE controller driver routes
through it.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23449
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add KEY_SETUP and KEY_VENDOR keys. Many Rockchip devices, including all of those in
e13cbab684 ("rockchip: enable SARADC; add buttons hotplug and ADC kmods to default packages")
have one or both of these buttons.
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23396
Signed-off-by: Robert Marko <robimarko@gmail.com>
OSLEC has been dropped upstream since Linux 6.16.
Reflect that by no longer providing the kernel module package
`kmod-echo` which essentially became an empty stub.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This improves on openwrt/openwrt@aeb9028aab by adding support for
other Dell EMC Edge620/640/680 devices and mapping
the interfaces to match the markings on the device.
This modifies the netdevices.mk file to set the boot flag for
ixgbe driver to load it in early stage of the boot process to
allow for proper mapping of the network interface PCI paths
inside the 02_network script. This will also allow other devices
using the ixgbe driver to do proper mapping in 02_network script.
The 02_network script is then modified to support all
dell-emc-620/640/680 devices. It now maps the network
interfaces via PCI paths to match the markings on the device.
The interface marked GE6 is still used for WAN with
interfaces GE1-GE5 used for LAN.
The SFP1 and SFP2 interfaces are left to be assigned by
the user.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/23110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Select `CONFIG_ROCKCHIP_SARADC=y` to enable Rockchip SAR ADC
Add ADC Ladder Buttons driver as a kernel module as well as `kmod-button-hotplug` to the list of
default packages for Rockchip targets that have buttons connected to ADC, not including some
devices (e.g. NanoPi R76S) that have ADC buttons which are not in the device tree.
This is needed to use buttons on Rockchip devices that are connected to ADC and not GPIO
Tested on FriendlyELEC NanoPi M5
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-mt7622-firmware package is only used by mt7622 SoC builtin WiFi.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22495
Signed-off-by: Robert Marko <robimarko@gmail.com>
kmod-sound-midi2 expects sound/core/snd-ump.ko, but
CONFIG_SND_UMP=y builds it in-kernel rather than as
a module. Replace the forced built-in setting with
plain CONFIG_SND_UMP so the module can be packaged
correctly.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/23265
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace EXTRA_CFLAGS with ccflags-y to fix builds on Linux 6.18.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/22930
Signed-off-by: Nick Hainke <vincent@systemli.org>
Replace EXTRA_CFLAGS with ccflags-y to fix builds on Linux 6.18.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/22930
Signed-off-by: Nick Hainke <vincent@systemli.org>
This contains many fixes from upstream Linux.
The code block from this patch was moved a bit in the function:
subsys/110-mac80211_keep_keys_on_stop_ap.patch
This patch was applied upstream:
subsys/330-mac80211-fix-crash-in-ieee80211_chan_bw_change-for-A.patch
Link: https://github.com/openwrt/openwrt/pull/23167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix dependency for kmod-drm-client-lib module:
error: recursive dependency detected!
symbol LINUX_6_18 is selected by PACKAGE_kmod-drm-client-lib
symbol PACKAGE_kmod-drm-client-lib is selected by LINUX_6_18
Fixes: e75ba35ed8 ("modules: video: introduce DRM client setup module")
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23124
Signed-off-by: Robert Marko <robimarko@gmail.com>
Going from 6.12 to 6.18 I see breakage with a missing dependency
that drivers/net/ethernet/amazon/ena/ena_netdev.c has on ptp.ko.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Link: https://github.com/openwrt/openwrt/pull/23098
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to the latest version, and fix build on targets without
FS_POSIX_ACL.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23090
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux commit c9e5ac0 ("lib/crypto: mips/md5: Migrate optimized code into
library") removed the MIPS-Octeon-specific MD5 implementation
(octeon-md5.ko) and replaced it with an optimized library implementation
in lib/crypto.
As a result, CONFIG_CRYPTO_MD5_OCTEON and the module
arch/mips/crypto/octeon-md5.ko no longer exist in kernels >= 6.18.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23031
Signed-off-by: Nick Hainke <vincent@systemli.org>
The pppox module is a dependency of pppoe/pptp/pppol2tp and does not
have a separate Kconfig symbol.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23077
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6.14 has introduced a DRM client setup library. Add kmod-drm-client-lib
to support it, and add it as a dependency to DRM modules which depend on it.
Link: https://github.com/openwrt/openwrt/pull/22975
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is required to build the motorcomm dwmac driver which is widely
used on loongson platforms.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/22923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Motorcomm YT6801 is a PCIe ethernet controller based on DWMAC4 IP. It
integrates an GbE phy, supporting WOL, VLAN tagging and various types
of offloading. It ships an on-chip eFuse for storing various vendor
configuration, including MAC address.
The PM and plat_data functions were slightly modified to build with
current kernel.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/22923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux commit 09371e1349c9 ("lib/crypto: powerpc/md5: Migrate optimized code into library")
removed the PowerPC-specific MD5 implementation (md5-ppc.ko) and
replaced it with an optimized library implementation in lib/crypto.
As a result, CONFIG_CRYPTO_MD5_PPC and the module
arch/powerpc/crypto/md5-ppc.ko no longer exist in kernels >= 6.18.
Link: https://github.com/openwrt/openwrt/pull/22732
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fixes:
ifxmips_aes.c: In function 'gcm_aes_decrypt':
ifxmips_aes.c:1803:14: error: assignment discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1803 | temp = walk.src.virt.addr;
| ^
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22921
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes:
ltq_atm.c: In function 'ltq_atm_probe':
ltq_atm.c:1840:36: error: passing argument 2 of 'platform_set_drvdata' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1840 | platform_set_drvdata(pdev, ops);
| ^~~
In file included from ltq_atm.c:40:
/workspaces/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/linux-6.18.21/include/linux/platform_device.h:276:47: note: expected 'void *' but argument is of type 'const struct ltq_atm_ops *'
276 | void *data)
| ~~~~~~^~~~
Fixes: c1fa85f659 ("treewide: use of_device_get_match_data")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22921
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 6.18 code works with older kernels as well. Remove the older section
and use the newer one always.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22925
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace conditional "LINUX_6_12:mod" / "!LINUX_6_12:mod" AUTOLOAD entries
with version-filtered module names using @lt6.18 / @ge6.18. This makes
version_filter emit plain module names into /etc/modules.d(e.g. "crc32c_generic"),
allowing kmodloader to find and load the correct module for the running kernel.
Fixes crc32c (and related crypto modules) not being autoloaded on 6.12 kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Migrate timer handling (removed in 6.13) and netdev dummy initialization
(removed in 6.16) to new methods with guards to not break older kernels.
This resolves compilation errors due to missing del_timer_sync(),
from_timer() and init_dummy_netdev().
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/22775
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing dependency kmod-ptp to fix the build error. We also
add symbol CONFIG_PTP_1588_CLOCK_OPTIONAL explicitly for kmod-ptp
because it is selected by CONFIG_PTP_1588_CLOCK. Fix:
Package kmod-iavf is missing dependencies for the following libraries:
ptp.ko
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
cryptd has been decoupled from crypto-misc in the 6.18 kernel. Fix:
ERROR: module '/home/runner/work/Actions_/Actions_/openwrt/build_dir/target-i386_pentium4_musl/linux-x86_generic/linux-6.18.20/crypto/cryptd.ko' is missing.
make[3]: *** [modules/crypto.mk:873: /home/runner/work/Actions_/Actions_/openwrt/bin/targets/x86/generic/packages/kmod-crypto-misc-6.18.20-r1.apk] Error 1
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MediaTek T-PHY controller supports multiple usb2.0, usb3.0 ports,
PCIe and SATA. ARM mediatek and ramips/mt7621 targets require this
package to make the XHCI work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was replaced upstream with a proper rng device that feeds into
/dev/random. No need for this anymore.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22766
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The rtl8812au-ct driver is obsolete and replaced by rtw88. It will need
tons of work to compile against 6.18 so for now limit it to 6.12.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update module files for kernel 6.18
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update module files for kernel 6.18
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
