Set up openwrt to handle the reset button appropriately (so that it
can trigger the various recovery modes) on the nanopi R6S and R6C models.
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set up openwrt to show boot progress on the nanopi R6S or R6C system LED.
The LED blinking states indicate the boot stage. The LED is defined as
a power LED, but can still be set to heartbeat in /etc/config/system
after the system is done booting.
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This setting is more suitable for device running OpenWRT.
Most OpenWRT targets are already default to this configuration,
and it has shown better performance in VPN (wireguard).
Fix: #17454
Signed-off-by: Kien Truong <duckientruong@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17575
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 8a477bafb4 backported an upstream patch
without refreshing the patches.
Fixes: 8a477bafb4 ("rockchip: fix phy reset on rk356x")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17474
Signed-off-by: Robert Marko <robimarko@gmail.com>
The commit 7160820d742a ("phy: rockchip: naneng-combphy: fix phy reset")
was backported to kernel 6.6 branch by upstream, however the correspond
dtsi fixes was not, resulting the following error:
```
[ 0.225521] rockchip-naneng-combphy fe830000.phy: error -ENOENT: failed to get phy reset
[ 0.227467] rockchip-naneng-combphy fe840000.phy: error -ENOENT: failed to get phy reset
```
So backport the dtsi fixes here manually.
Fixes: 89b2356b8c ("kernel: bump 6.6 to 6.6.69")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17468
Signed-off-by: Robert Marko <robimarko@gmail.com>
These get dynamically set based on compiler version. Not relevant for
targets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds OpenWRT's LED aliases to the board DTS
for showing system status on the NanoPi R3S.
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the FriendlyElec NanoPi R3S.
CPU: Rockchip RK3566, Quad-core Cortex-A55
RAM: 2GB LPDDR4X
Ethernet: GMAC RTL8211F GbE, PCIe R8111H GbE
USB3.0 Host: Type-A x1
Storage: MicroSD Slot x 1, and optional on-board 32GB eMMC
Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds
LED: LED x 3
RTC: One low-power RTC, supports backup battery input
Both GbE controllers are working (WAN eth0, LAN eth1).
Appropriate LAN/WAN interface assignments and MAC address generation.
All three LEDs are working.
USB appears to be working and has been tested with mass storage.
Installation - microSD:
-Uncompress the OpenWRT sysupgrade.img.gz
-Write image to microSD card using dd or similar tool
Installation - eMMC:
-Boot from microSD
-Uncompress the OpenWRT sysupgrade.img.gz
-Flash to eMMC : dd if=x.img of=/dev/mmcblk0
-sync
-Remove microSD card
-Reboot
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This board is also as known as Bananapi BPi-M7.
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8/16/32GB LPDDR4/LPDDR4x RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (RED / GREEN)
16GB/32GB/64GB/128GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
USB 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This enables the M.2 E-key on ROCK 5A board.
Reorder rk356x patch while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes model name in dts as below:
Radxa ROCK3 model A -> Radxa ROCK 3A
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16232
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kconfig symbols CONFIG_ARM64_CNP and CONFIG_ARM64_EPAN got exposed
by enabling CONFIG_ARM64_PAN. Enable them as well, as just like for
PAN, also EPAN and CNP will be detected at runtime at no cost.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable the CONFIG_ARM64_PAN kernel security option, which leverages the
ARMv8.1 Privileged Access Never (PAN) extension to prevent the kernel
from directly accessing user space memory.
Instead, copy_to_user and similar functions must be used for data
transfer between kernel and user space. This feature is automatically
disabled at runtime on CPUs without PAN support, making it a no-op in
those cases.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
2500 Base-T
RGB LED
eMMC Connector
SPI-NOR 16MB
Micro-SD Slot
2x USB 2.0 Port
2x USB 3.0 Port
Headphone Jack
M.2 E-Key
M.2 M-Key
USB PD 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
1000 Base-T
Status LED
eMMC/SPI Connector
Micro-SD Slot
2x USB 3.0 Port
2x USB 2.0 Port
Headphone Jack
M.2 E-Key
USB PD/QC 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we have rk3588 support :)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SUPPORTED_DEVICES is required for Radxa ROCK Pi S.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We need to configure the led and network config for this board on
start as per the others
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches for the nanopi r6s board, backporting from 6.9 where
basic support is landing.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the image check failed on system upgrade
"Image check failed:
upgrade: Device radxa,rock3a not supported by this image
upgrade: Supported devices: radxa,rock-3a"
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 has a RTL8723DU Wi-Fi 4 on-board device. enable
it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S has a RTL8723DS Wi-Fi 4 on-board device. enable it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Import patch from mainline Linux to fix issue with PERST# signal
polarity.
Quote from commit message:
"This extra, very short, PERST# assertion + deassertion has been
reported to cause issues with certain WLAN controllers, e.g. RTL8822CE."
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testing turned out that the HWRNG quality varies greatly on RK3566,
even on supposedly identical boards and SoC revisions.
Hence enable the HWRNG driver only on RK3568 for now.
Allow users to simply tune sample_count and quality to allow easily
testing results on different boards and SoCs.
Link: https://patchwork.kernel.org/project/linux-arm-kernel/cover/cover.1720969799.git.daniel@makrotopia.org/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Radxa ROCK Pi E v3.0 is a compact networking SBC[1] using the Rockchip
RK3328 SoC.
Hardware
--------
- Rockchip RK3328 SoC
- Quad A53 CPU
- 512MB/1GB/2GB DDR4 RAM
- 4/8/16/32GB eMMC
- Micro SD Card slot
- WiFi 4 and BT 4, or WiFi 5 and BT 5 (not supported yet)
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x 100M Ethernet
- 1x USB 3.0 Type-A port (Host)
- 1x 4-ring 3.5mm headphone jack
- 40 Pin GPIO header
[1] https://radxa.com/products/rockpi/pie
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15984
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
stop "heartbeat" which happens before OpenWrt controls LED. instead,
just turn LED on.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15913
Signed-off-by: Robert Marko <robimarko@gmail.com>
use u-boot-rockchip.bin to copy SPL/TPL/U-Boot to the image.
since binman was used in mainline u-boot for rockchip, we can use
u-boot-rockchip.bin instead of idbloader.img and u-boot.itb.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15815
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Hardware spec:
- Rockchip RK3568 Quad-core ARM Cortex-A55 CPU 2GHz
- GPU Mali-G52 1-Core-2EE OpenGL ES3.2 Vu1kn 1.1 OpenCL 2.0
- Memory2G DDR3 SDRAM (option 4G)
- Storage Onboard 16GB eMMC Flash, Micro SD-Card slot, SATA 3.0 Port,SPI flash
- Network 5 x 10/100/1000 Mbit/s Ethernet MT7531
- Display 1 HDMI port, 2 DSI interface(1 DSI can change to LVDS by software)
- Camera 1 CSI camera interface
- Audio Output HDMI & I2S & Speaker & Headphone
- USB port USB 3.0 PORT (x2), micro USB OTG (x1)
- PCIE 1 mini pcie interface & 1 M.2 key-e interface
- Remote IR Receiver (x1)
- GPIO 40 Pin Header : GPIO (x28) and Power (+5V, +3.3V and GND).
- Switches Reset button, Power button, U-boot button
- LED Power Status
- Power Source 12 volt 2A via DC Power
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
Boot from the SD card
1-hold down the MaskRom button
2-Connect DC power
3-Wait 5 seconds, release the button.
eMMC Installation:
1-Uncompress the OpenWrt sysupgrade image
2-fash to eMMC
dd if=openwrt-rockchip-armv8-sinovoip_bpi-r2-pro-squashfs-sysupgrade.img of=/dev/mmcblk1
sync
3-remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Rockchip SoCs used to have a random number generator as part of their
crypto device, and support for it has to be added to the corresponding
driver.
Newer Rockchip SoCs like the RK3568 have an independent True Random
Number Generator device. Import pending patchset which adds a driver for
it, include it in Kconfig and enable it in the device tree.
Doing so significantly reduces the time needed to boot devices based on
those SoCs, from about 27 seconds until Ethernet is up and running to
less than 13 seconds with a minimal snapshot image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
In official OpenWrt we use kmod-r8169 driver provided by upstream kernel
instead of kmod-r8168 driver from Realtek.
Fixes: afca1236f3 ("rockchip: add NanoPi R4S Enterprise Edition build")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Now we support parsing the color and function properties.
Ref: e814acc599 ("base-files: support parse DT LED color and function")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Booting from non-MMC devices on Rockchip targets without this
change results in a boot failure:
Model: FriendlyElec NanoPi R5S
Net: eth0: ethernet@fe2a0000
Hit any key to stop autoboot: 0
** Booting bootflow 'nvme#0.blk#1.bootdev.part_1' with script
** No partition table - mmc 0 **
** No partition table - mmc 0 **
Couldn't find partition mmc 0:1
Can't set block device
Wrong Image Type for bootm command
ERROR -91: Protocol wrong type for socket: can't get kernel image!
Boot failed (err=1)
This change fixes the default boot script for Rockchip targets to
support booting from non-MMC devices such as NVMe or USB drives.
Some targets with only a boot rom (e.g. NanoPi R5S) may require u-boot
to be installed on the eMMC or a MicroSD card in order to boot from
non-MMC devices.
Fixes: #14420
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Justin Klaassen <justin@tidylabs.app>
The default strength is not enough to provide stable connection
under 3.3v LDO voltage.
Fixes: 32d5921b8b ("rockchip: add Orange Pi R1 Plus LTS support")
Fixes: #13117Fixes: #13759
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
XHCI bus numbers are assigned dynamically, it may varies among boards,
match the device irq name with regexp, drop the hardcoded name.
Signed-off-by: Furong Xu <xfr@outlook.com>
All devices in the rockchip target have appended image-metadata. Enforce
the presence of this metadata to avoid flashing incomplete images.
This is the de-facto standard for almost all OpenWrt targets.
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable all necessary drivers for the rk356x SoCs, including PHY,
SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
It's applicable for all devices so move it to default to reduce
redudant code. Addtionally introduce a new variable `BOOT_SCRIPT`
to allow custom boot script (if necessary).
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
From the symbol help message:
> SLUB has extensive debug support features. Disabling these can result
> in significant savings in code size.
There seems to be no need to enable those debugging features for
standard use.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for Radxa ROCK Pi E, rockchip rk3328 board.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- Storage:
1 x MicroSD Slot
1 x eMMC Module Slot
- USB Host/OTG:
1 x USB3.0 Type A HOST
1 x USB2.0 HOST (40-pin pin-header)
- Wireless
RTL8723DU/RTL8821CU
- Debug Serial:
1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
Type-C 5V
Optionally PoE
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
This add support for PINE64 ROCK64, rockchip rk3328 board.
Specifications:
4 x ARM Cortex A53 cores @ 1.5 GHz
ARM Mali 450 MP2 GPU
LPDDR3 RAM (up to 4GB)
Gigabit Ethernet
Micro SD Slot
eMMC module slot
SPI Flash 128Mbit
4K digital video out
2x USB 2.0 Host
1x USB 3.0 Host
PI-2 bus
PI-P5+ bus
IR R/X port
Real Time Clock (RTC) port
Power Over Ethernet (POE) (when using optional HAT module)
A/V jack
Power, Reset and Recovery buttons
3.5mm barrel power (5V 3A) port
To install write image to the sd using dd (dd if=*.img of=/*)
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR3 RAM
1x 1000 Base-T
1 GPIO LED (status)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
16GB eMMC
1x USB 3.0 Port
2x USB 2.0 Port
1x USB Type-C Port
1x M.2 PCI-E Port
AP6356S (BCM4356) SDIO WiFi & Bluetooth adapter
--------
Note: AP6356S is not supported yet due to the lack of firmware and NVRAM
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
