7a1fe3fa8e
628 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Eric Schäfer
|
f3eca7cbc1 |
ramips: add support for Zyxel LTE7490-M904
The Zyxel LTE7490-M904 is an 802.3at PoE powered LTE outdoor (IP68) CPE
with integrated directional antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E 802.11b/g/n
- Switch: 1 LAN port (1 Gbps)
- LTE/3G/2G: Quectel EG18-EA LTE-A Cat. 18 connected by USB3 to SoC
- SIM: 1 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/amber under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to LTE bridge or router.
The wifi interface is intended for installation and/or temporary
management purposes only.
UART Serial:
57600N1, located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover and 12 screws holding the back plate
and antenna cover together. Be careful with the cables.
Installation from OEM web GUI:
- Log in as "admin" on OEM web GUI
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image and reboot
For more details about flashing see:
|
||
Andreas Gnau
|
3e7337feea |
ramips: Add support for Genexis / Inteno Pulse EX400
Add support for Genexis Pulse EX400 / Inteno Pulse EX400. A branded
variant for the Finnish ISP DNA has already been added in
|
||
Coia Prant
|
6a1bdcf545 |
ramips: add support for Hongdian H8922 v30
This is an industrial 4G router equipped with OpenWrt 14.07 OEM customized version WARNING: The original firmware device tree is common to multiple boards, and the device tree name is H9350. This submitted device tree is a modified version, which deletes the non-this-device parts and adds GPIO watchdog. Specification: - SoC: MediaTek MT7620A - Flash: 16 MB - RAM: 128 MB - Power: DC 5V-36V 1.5A - Ethernet: 1x WAN, 4x LAN (10/100 Mbps) - Wireless radio: 802.11n 2.4g-only - LED: System/Power (RUN): GPIO/26 active-low Ethernet: 1x WAN, 4x LAN Modem 1: GPIO/66 active-low RF 1 (Modem 1 Signal): GPIO/67 active-low Modem 2: GPIO 71 active-low RF 2 (Modem 2 Signal): GPIO/24 active-low WLAN: GPIO/72 active-low WPS: GPIO/12 active-low - Button: WPS / RESET: GPIO/34 active-low - UART: 1x UART on PCB - 115200 8N1 - GPIO Watchdog: GPIO/62 mode=toggle timeout=1s - PCIe: 2x miniPCIe for modem - SIM Slots: 2x SIM Slots Issue: - No factory partition, eeprom is located at /lib/firmware/mt7620a.eeprom Flash instruction: Using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put rootfs into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press Ctrl+C to break auto boot. 5. Use `system 6` command and follow the instruction to set device and tftp server IP address and input the rootfs file name. U-boot will then load the rootfs and write it into the flash. 6. Use `system 1` command and follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware once. 7. Login to LuCI and use LuCI upgrade firmware. Original Firmware Dump / More details: https://blog.gov.cooking/archives/research-hongdian-h8922-and-flash.html Signed-off-by: Coia Prant <coiaprant@gmail.com> Tested-by: Coia Prant <coiaprant@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17472 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Tianling Shen
|
96c6608346 |
mediatek: add support for CMCC A10
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
George Moussalem
|
9a7192c08e |
qualcommax: ipq50xx: Add support for Linksys MR5500
Add support for Linksys MR5500 (Hydra 6 Pro).
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Kingston D2516ECMDXGJD (512 MiB)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Gigadevice GD5F2GQ5REYIH (256 MiB)
* LEDs: 1x multi-color PWM LED
1x blue led for USB (GPIO 19 Active High)
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
5x ethernet port LEDs (amber for activity & green for link up)
* Peripherals: 1x USB2 (powered by GPIO 17 Active Low)
support for USB3 will be added in a separate PR
* FCC ID: 2AYRA-03734
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MR5500: https://support.linksys.com/kb/article/207-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MR5500_1.1.2.209598_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MR5500_1.1.2.209598_prod.img kernel
4. Boot from USB
This allows you loading an OpenWrt image into RAM and is meant for recovery scenarios only.
Enable loading image from USB in u-boot. From serial or SSH:
fw_setenv bootusb 'usb start && usbboot &loadaddr && bootm $loadaddr'
fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Copy OpenWrt initramfs image to USB:
dd bs=1M if=openwrt-qualcommax-ipq50xx-linksys_mr5500-initramfs-uImage.itb of=/dev/sda
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17958
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
|
George Moussalem
|
fe379eb1c1 |
qualcommax: ipq50xx: add support for Linksys SPNMX56
The SPNMX56 is an ISP-branded and distributed device similar to the MX5500
with the same Wifi chips (IPQ5018 for 2.4G and QCN9074 for 5G) but has an
additional QCA8081 PHY providing a 2.5gbps ethernet WAN port.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T) and a
QCA8081 phy (up to 2.5 Gbps)
* Flash: Gigadevice GD5F2GM7RExxG (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1)
and click 'CA' in the bottom right corner -> Connectivity ->
Manual Upgrade. Alternatively, browse to http://<router IP>/fwupdate.html
Upload openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
Optionally flash 2nd partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware
hit Enter once booted and enter credentials (login: root, password: admin)
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
Firmware for this device cannot be searched for on the Linksys website.
Instead, we'd have to use serial to intercept the URL of the firmware
while it's trying to update. Firmware is ISP specific:
Toob (UK): http://download.linksys.com/updates/20241125t080737/FW_MX56TB_1.0.1.216218_prod.img
The intention is to collect URLs for different ISPs on a wiki page.
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX56TB_1.0.1.216218_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX56TB_1.0.1.216218_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17968
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
Chukun Pan
|
51d485ef31 |
qualcommax: add support for Aliyun AP8220
Aliyun AP8220 is an AP manufactured by Edgecore.
(Very similar to Edgecore EAP102)
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 1GB of DDR4 600MHz
Flash1: MX25U3235F 4MB
Flash2: MX30UF1G18AC 128MB
Ethernet: 2x 2.5G RJ45 port
USB: 2x USB-A 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Power: DC 12V / PoE
Flash instructions:
1. Connect the router via serial port
2. Keep pressing @ until uboot is interrupted
3. Download the initramfs image, rename it to
initramfs.bin, host it with tftp server
4. Run these commands:
tftpboot initramfs.bin
bootm
5. After openwrt boots up, use scp or luci
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
Klaas Demter
|
71a966c480 |
uboot-envtools: add support for ZyXEL GS-1900-24EP
It seems the that this was forgotten during initial adding of the
device in
|
||
Robert Marko
|
1bb1b03f69 |
uboot-envtools: ipq60xx: code simplification
Do the same code simplification as was done for ipq807x to avoid code duplication. Link: https://github.com/openwrt/openwrt/pull/17907 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
George Moussalem
|
398f4a9737 |
qualcommax: ipq50xx: add support for Linksys MX2000 and MX5500
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: MX2000: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
MX5500: QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
Ivan Deng
|
734331e4e6 |
ipq60xx: fix uboot-envtools file syntax error in uci-defaults
The syntax error prevented the correct creation of all ipq60xx U-Boot environment files: /etc/config/ubootenv and /etc/fw_env.config Signed-off-by: Ivan Deng <hongba@rocketmail.com> Link: https://github.com/openwrt/openwrt/pull/17755 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Paweł Owoc
|
9decfc82dc |
uboot-envtools: ipq807x: remove number of blocks and code simplification
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17463 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Paweł Owoc
|
07f8319d2d |
qualcommax: ipq807x: add support for Linksys HomeWRK
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17463 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Shiji Yang
|
433be50c94 |
uboot-envtools: update to v2025.01
Update to latest version. There are no patches that need to be refreshed. Signed-off-by: Shiji Yang <yangshiji66@qq.com> Link: https://github.com/openwrt/openwrt/pull/17538 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Alexandru Gagniuc
|
a00ff9f6d1 |
qualcommax: ipq60xx: add TP-Link EAP610-Outdoor support
TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is
wall or pole mountable, and rated for outdoor use. It can only be
powered via PoE.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: ESMT PSR1GA30DT 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap610-outdoor-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
The tplink2022 image format
============================
The vendor images of this device are packaged in a format that does
not match any previous tplink formats. In order for flashing to work
from the vendor's web UI, firmware updates need to be packaged in
this format. The `tplink-mkimage-2022.py` is provided for this
purpose.
This script can also analyze vendor images, and extract the required
"support" string. This string is checked by the vendor firmware, and
images with a missing or incorrect string are rejected.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14922
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
|
Robert Marko
|
285bdd29cb |
uboot-envtools: ipq60xx: remove number of blocks
It is not required to specify the number of blocks as envtools are able to autodetect it. Link: https://github.com/openwrt/openwrt/pull/17504 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Paweł Owoc
|
adfb1b7696 |
qualcommax: ipq807x: add support for Linksys MX4300 (LN1301)
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin image. More details can be found here: https://support.linksys.com/kb/article/6564-en/ After first boot check actual partition: - fw_printenv -n boot_part and install firmware on second partition using command in case of 2: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel and in case of 1: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel 2. Installation using serial connection from OEM firmware (default login: root, password: admin): - fw_printenv -n boot_part In case of 2: - flash_erase /dev/mtd21 0 0 - nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin or in case of 1: - flash_erase /dev/mtd23 0 0 - nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin After first boot install firmware on second partition: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel or: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel 3. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX Stop u-boot and run: - usb start && usbboot $loadaddr 0 && bootm $loadaddr Write firmware to the flash from initramfs: - mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel and: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel 4. Back to the OEM firmware: - mtd -e kernel -n write FW_MX4300_1.0.4.215382_prod.img kernel and: - mtd -r -e alt_kernel -n write FW_MX4300_1.0.4.215382_prod.img alt_kernel 5. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr' - fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' Co-authored-by: Qiyuan Zhang <zhang.github@outlook.com> Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: https://github.com/openwrt/openwrt/pull/16070 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Roland Reinl
|
b3ce08e0b6 |
mediatek: filogic: Add support for D-Link AQUILA PRO AI M60
Specification: - MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX) - MT7531 switch - 512MB RAM - 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size - 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1) - 3 buttons (WPS, reset, LED on/off) - 1x 2.5 Gbit WAN port with Maxlinear GPY211C - 4x 1 Gbit LAN ports Disassembly: - There are five screws at the bottom: 2 under the rubber feet, 3 under the label. - After removing the screws, the white plastic part can be shifted out of the blue part. - Be careful because the antennas are mounted on the side and the top of the white part. Serial Interface - The serial interface can be connected to the 4 pin holes next to/under the antenna cables. - Note that there is another set of 4 pin holes on the side of the board, it's not used. - Pins (from front to rear): - 3.3V (do not connect) - TX - RX - GND - Settings: 115200, 8N1 MAC addresses: - MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52) - MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53) - WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52) - LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53) - WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54) - WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57) Flashing via OEM web interface: - Currently not supported because image crypto is not known Flashing via recovery web interface: - This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition - Use a Chromium based browser, otherwise firmware upgrade might not work - Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red - Upload the recovery image, this will take some time. LED will continue flashing red during the update process - The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing - If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case: - Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image) - Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60 - OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface) - Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used Flashing via Initramfs: - Before switching to OpenWrt, ensure that both partitions contain OEM firmware. - This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface. - Flashing via OEM web interface will automatically flash the currently not active partition. - Open router, connect serial interface - Start a TFTP server at 192.168.200.2 and provide the initramfs image there - When starting the router, select "7. Load Image" in U-Boot - Settings for load address, load method can be kept as they are - Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2) - Enter the file name of the initramfs image - Confirm "Run loaded data now?" question after loading the image with "Y" - OpenWrt initramfs will start now - Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM - Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0 - During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition Reverting back to OEM: - Boot the initramfs image as described in "Flashing via Initramfs" above - Copy the backed up ubi partition to /tmp (e.g. by using SCP) - Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4 - Reboot the device, OEM firmware will start now Signed-off-by: Roland Reinl <reinlroland+github@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17296 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Edward Chow
|
42254d3f5f |
ath79: port buffalo WZR-450HP2 from ar71xx
Referencing commit
|
||
Jianyu Zhuang
|
e0813dc071 |
mediatek: filogic: add support for Tenbay WR3000K
Tenbay WR3000K is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B. - SoC: MetiaTek MT7981B - RAM: Hynex H5TQ2G863GFR 512MiB - Flash: Winbond W25N01GVZEIG 128MiB - Wi-Fi: MediaTek MT7976C (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000) - MediaTek MT7915E: 2.4GHz and 5GHz - Ethernet: 1x 10/100/1000 Mbps WAN + 3x 10/100/1000 Mbps LAN - Switch: MediaTek MT7531AE - UART: J4 (115200 baud) - LEDs: Power - Buttons: Reset, WPS - PWR: 12V/1A DC, 5.5×2.1 connector | Vendor | OpenWrt Interface | Address | Notes | |---------|-------------------|---------------|------------------------------------------------| | WAN | wan | Label MAC | Stored MAC in factory + offset 4, label MAC is Stored MAC - 2 | | LAN | br-lan | Label MAC+1 | | | 2.4GHz | phy0-ap0 | Label MAC + 2 | | | 5GHz | phy1-ap0 | Label MAC + 3 | | - 0x000000000000-0x000000100000 : "BL2" - 0x000000100000-0x000000180000 : "u-boot-env" - 0x000000180000-0x000000380000 : "Factory" - 0x000000380000-0x000000580000 : "FIP" - 0x000000580000-0x000003580000 : "ubi" - 0x000003580000-0x000006580000 : "ubi1" - 0x000006580000-0x0000065a0000 : "Product" - 0x0000065a0000-0x000007580000 : "Custom" - The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi. - The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt. - id: 0, kernel - id: 1, rootfs - id: 2, rootfs_data - **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102). - **Dupont Wires** (male-to-male, 3 wires). - **PC/Laptop** with a serial communication tool. - Screwdriver (to open the router case). 1. **OpenWrt Firmware**: - Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/). 2. **Serial Communication Tool**: - Windows: PuTTY, Tera Term. - Linux/Mac: Minicom, screen. 3. (Optional) **TFTP Server**: - Install a TFTP server like Tftpd64 or tftp-hpa. --- 1. Open the router casing and locate the **TX, RX, and GND** pins. 2. Connect the router pins to the USB-to-TTL adapter as follows: - **TX (router)** → **RX (adapter)** - **RX (router)** → **TX (adapter)** - **GND (router)** → **GND (adapter)** 3. Do **not** connect the VCC pin to avoid damage. - **Baud rate**: 115200 - **Data bits**: 8 - **Stop bits**: 1 - **Parity**: None - **Flow control**: None --- 1. Power on the router and observe the serial terminal output. 2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process. 3. You will see the U-Boot Boot Menu: ```plaintext *** U-Boot Boot Menu *** 1. Factory mode 2. Startup system (Default) 3. Upgrade firmware 4. Upgrade ATF BL2 5. Upgrade ATF FIP 6. Upgrade single image 7. Load image 0. U-Boot console Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit ``` 4. Select Option 0 by typing 0 and pressing Enter. 5. Input into ```plaintext MT7981> setenv boot_from ubi MT7981> saveenv Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK Writing to MTD device 'nmbm0'... OK OK MT7981> printenv baudrate=115200 boot_from=ubi ... ``` the above indicates system will start from *ubi*. and then type ```plaintext MT7981> reset ``` will boot from *ubi* 1. Power on the router and observe the serial terminal output. 2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process. 3. You will see the U-Boot Boot Menu: ```plaintext *** U-Boot Boot Menu *** 1. Factory mode 2. Startup system (Default) 3. Upgrade firmware 4. Upgrade ATF BL2 5. Upgrade ATF FIP 6. Upgrade single image 7. Load image 0. U-Boot console Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit ``` 4. Choose Option 3: Upgrade Firmware Enter Upgrade Mode Select Option 3 by typing 3 and pressing Enter. Upgrade Methods You will be prompted to choose between: ```plaintext *** Upgrading Firmware *** Run image after upgrading? (Y/n): y Available load methods: 0 - TFTP client (Default) 1 - Xmodem 2 - Ymodem 3 - Kermit 4 - S-Record 5 - RAM Select (enter for default): 0 Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.10 Input IP netmask: 255.255.255.0 Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin ``` Type Enter to proceed. The router will erase the old firmware and write the new one. Signed-off-by: Jianyu Zhuang <xzjianyu@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17172 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Shymon Samsel
|
4b6e7da0f7 |
ipq807x: add support for TP-Link EAP620 HD v1
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
Chuncheng Chen
|
502916468e |
ramips: add support for ASUS 4G-AX56
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
|
||
Yaoguang Bai
|
6b32a5d768 |
mediatek: filogic: add support for NRadio C8-668GL
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC. - **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz) - **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4 - **Flash**: ESMT FC51L08SFY3A 8GB eMMC - **Ethernet**: - 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE) - 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0) - 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL) - **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000) - **Buttons**: Reset, WPS - **LEDs**: Power, 5G, 4G, WiFi - **SIM Slot**: 1x Nano SIM - **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62) - **Power**: 12V/2A DC, 5.5×2.1 connector The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows: | Vendor | OpenWrt Interface | Address | Notes | |---------|-------------------|---------------|------------------------------------------------| | LAN | br-lan | Label MAC | Default | | WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN | | 2.4GHz | phy0-ap0 | Label MAC | | | 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) | | Modem | eth1 | Label MAC+2 | | 1. Log in to the router via `http://192.168.66.1`/. 2. Upgrade the official firmware to dual-system mode. 3. Select **Burn second system** and upload the `sysupgrade.bin` image. - Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot. 4. Wait for 30 seconds and click **Switch system**. 5. The device will reboot and switch to OpenWrt. Set the U-Boot environment variable `boot_system=0` and reboot: ```bash fw_setenv boot_system 0 ``` Power off the router, hold the **WPS button**, and power it back on. 1. Rename the stock firmware file to **`recovery.bin`**. 2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router. 3. Run a TFTP server and place the `recovery.bin` file in its root directory. 4. Power off the router, press and hold the **Reset button**, and power it back on. 5. Release the Reset button when the TFTP server shows activity. 6. Wait for the router to flash the firmware and reboot automatically. - By default, `lan4` is part of `br-lan` and uses the label MAC address. - To query the RM520N-GL module, use the following command: ```bash cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2 ``` Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club> Link: https://github.com/openwrt/openwrt/pull/17093 Signed-off-by: John Crispin <john@phrozen.org> |
||
Vladyslav Andreichykov
|
9c55866fad |
qualcommax: ipq60xx: add Linksys MR7350 support
Linksys MR7350 is a 802.11ax Dual-band router/AP. Specifications: * CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz * RAM: 512MB of DDR3 * Storage: 256Mb NAND * Ethernet: 5x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate * LED-s: * RGB system led * USB blue led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition: fw_printenv -n boot_part - Change the partition: fw_setenv boot_part 1 or fw_setenv boot_part 2 depending on the current partition - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn> Co-Authored-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com> Link: https://github.com/openwrt/openwrt/pull/14807 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Mikhail Zhilkin
|
ee8df790ca |
mediatek: MERCUSYS MR90X v1: add OpenWrt U-Boot (UBI) layout
This commit adds OpenWrt U-Boot (UBI) layout support for MERCUSYS MR90X v1. Stock U-Boot UBI size: 50 MiB OpenWrt U-boot UBI size: 126 MiB Install ------- 1. Perform steps 1-14 of the OpenWrt installation guide (use OpenWrt initramfs-recovery.itb instead of initramfs-kernel.bin at the step 10, 12 and 14). Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation 2. Make backups: ``` cat /dev/mtd0 > /tmp/boot.bin cat /dev/mtd5 > /tmp/tp_data.bin ``` Copy /tp_data dir content, /tmp/boot.bin and /tmp/tp_data.bin and to your PC using scp. You can also backup the remaining partititons. Copy backups to a safe place, they are required for the next steps and stock firmware recovery. 3. Reboot to OpenWrt initramfs: ``` reboot ``` 4. Copy OpenWrt ubi-bl31-uboot.fip, ubi-preloader.bin, ubi-squashfs-sysupgrade.itb and MT7986_EEPROM.bin, default-mac (from /tp_data backup) to the /tmp folder of the router using scp. 5. Prepare UBI: ``` ubidetach -p /dev/mtd3; ubiformat /dev/mtd3 -y; ubiattach -p /dev/mtd3 ubimkvol /dev/ubi0 -N fip -t static -s 1MiB ubiupdatevol /dev/ubi0_0 /tmp/ubi-bl31-uboot.fip ubimkvol /dev/ubi0 -N ubootenv -s 0x1f000 ubimkvol /dev/ubi0 -N ubootenv2 -s 0x1f000 ``` 6. Install kmod-mtd-rw and unlock partitions: ``` opkg update && opkg install kmod-mtd-rw insmod mtd-rw i_want_a_brick=1 mtd unlock boot mtd unlock bl2 mtd unlock factory ``` 7. Prepare "factory" partition: ``` dd if=/dev/zero bs=$((0x8000)) count=1 | tr '\000' '\377' > /tmp/factory.bin dd if=/tmp/MT7986_EEPROM.bin of=/tmp/factory.bin conv=notrunc dd if=/tmp/default-mac >> /tmp/factory.bin ``` 8. Write "factory" partition: ``` mtd erase factory mtd write /tmp/factory.bin factory ``` 9. Write preloader partition: ``` mtd erase bl2 mtd write /tmp/ubi-preloader.bin bl2 ``` 10. Write OpenWrt sysupgrade image: ``` sysupgrade -n /tmp/ubi-squashfs-sysupgrade.itb ``` Recovery -------- 1. Place OpenWrt initramfs-recovery.itb image (with original name) on the tftp server (IP: 192.168.1.254). 2. Press "reset" button and power on the router. After ~10 sec release the button. 3. Use OpenWrt initramfs system for recovery. BL2 and FIP recovery -------------------- Use mtk_uartboot and UART connetion if BL2 or FIP in UBI is destroyed: Link: https://github.com/981213/mtk_uartboot Link: https://openwrt.org/toh/mercusys/mr90x_v1#serial Return to stock: ---------------- 1. Copy "boot" partition backup (boot.bin) to the /tmp dir of the router using scp. 2. Install kmod-mtd-rw: ``` opkg update && opkg install kmod-mtd-rw ``` 3. Restore stock U-Boot: ``` insmod mtd-rw i_want_a_brick=1 mtd unlock boot mtd erase boot mtd write /tmp/boot.bin boot ``` 4. Erase UBI and reboot: ``` mtd erase ubi reboot ``` 5. Open U-Boot web recovery, upload stock firmware image and start upgrade. Link: http://192.168.1.1 6. Complete steps 1-9 of the OpenWrt installation guide to get root rights. Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation 7. Upload "tp_data" partition backup (tp_data.bin) to the /tmp folder of the router using scp. 8. Restore stock calibrations: ``` mtd write /tmp/tp_data.bin tp_data reboot ``` 9. Perform "factory restore" via stock firmware web interface. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Link: https://github.com/openwrt/openwrt/pull/16744 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
Mikhail Zhilkin
|
d413163832 |
mediatek: Routerich AX3000: add OpenWrt U-Boot layout
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The aims: 1. Get open-source U-Boot; 2. Get maximum available free space in OpenWrt. Install ------- 1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the /tmp folder of the router using scp. 2. Make mtd partitions backups: http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock contents 3. Install kmod-mtd-rw: ``` opkg update && opkg install kmod-mtd-rw ``` 4. Write FIP and preloader: ``` insmod mtd-rw i_want_a_brick=1 mtd unlock BL2 mtd erase BL2 mtd write /tmp/ubootmod-preloader.bin BL2 mtd unlock FIP mtd erase FIP mtd write /tmp/ubootmod-bl31-uboot.fip FIP ``` 5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root with IP 192.168.1.254. 6. Reboot router: ``` reboot ``` U-Boot will automatically download from the tftp server and boot OpenWrt initramfs system. 7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the router using scp. 8. Run sysupgrade: ``` sysupgrade -n /tmp/squashfs-sysupgrade.itb ``` Recovery -------- 1. Place OpenWrt initramfs-recovery.itb image (with original name) on the tftp server (IP: 192.168.1.254). 2. Press "reset" button and power on the router. After ~10 sec release the button. 3. Use OpenWrt initramfs system for recovery. BL2 and FIP recovery -------------------- Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed: Link: https://github.com/981213/mtk_uartboot Return to stock: ---------------- 1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the router using scp. 2. Install kmod-mtd-rw: ``` opkg update && opkg install kmod-mtd-rw ``` 3. Restore stock U-Boot and reboot: ``` insmod mtd-rw i_want_a_brick=1 mtd unlock BL2 mtd erase BL2 mtd write /tmp/BL2.bin BL2 mtd unlock FIP mtd erase FIP mtd write /tmp/FIP.bin FIP reboot ``` 4. Open U-Boot web recovery, upload stock firmware image and start upgrade. Link: http://192.168.1.1 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Link: https://github.com/openwrt/openwrt/pull/16791 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
George Oldfort
|
2898d1d126 |
mediatek: add support for Acer Predator W6d and Acer Vero W6m
This commit adds support for two variants of the already supported router Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller instead of the KTD2061 LED controller of the W6/W6d). The device tree for the W6m refers to the KTD202x driver suggested in PR #16860. Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh removes the code repetition in (old) lines 121 to 124 on the occasion. This is the last of four commits into which the original commit was split to make reviews easier and more targeted. Signed-off-by: George Oldfort <openwrt@10099.de> Link: https://github.com/openwrt/openwrt/pull/16861 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
George Oldfort
|
e7aaba2587 |
mediatek: make use of Acer Predator Connect W6's u-boot environment
In order to prepare OpenWrt support for other Acer W6 devices and to adapt the procedure to read and set mac addresses which other devices of the same target are using (instead of needing an additional script and creating an additional structure in the file system), this commit - reads device mac addresses from u-boot environment - avoids the detour via the file system to set the mac addresses - drops redundant file /lib/preinit/05_extract_factory_data.sh The idea and the implementation were thankfully taken from PR #16410. This is the second of four commits into which the original commit was split to make reviews easier and more targeted. Signed-off-by: George Oldfort <openwrt@10099.de> Link: https://github.com/openwrt/openwrt/pull/16861 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Enrico Mioso
|
785ebf2baf |
uboot-envtools: add support for GatoNetworks GDSP
This configuration should work with both stock and OpenWrt-based U-Boot. Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> |
||
David Lutz
|
a7abc7ec3b |
ath79: Add support for Sophos AP15C
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit
|
||
Piotr Dymacz
|
efb8764a69 |
uboot-envtools: ath79: add support for ALFA Network WiFi CampPro Nano Duo
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
John Crispin
|
b89b19b854 |
uboot-envtools: add a board.d script to load defaults from the environment
This allows loading default wifi credentials, passwords and ssh keys on firstboot. Signed-off-by: John Crispin <john@phrozen.org> |
||
|
John Crispin
|
84577e48bc |
uboot-envtools: add fw_loadenv tool
This tool will load the uboot environment to /var/run/uboot-env/. This allows more efficient use when accessing multiple variables. Signed-off-by: John Crispin <john@phrozen.org> |
||
Chris Webb
|
7eda44f536 |
uboot-mediatek: support GL.iNet GL-X3000 and GL-XE3000
Add u-boot support based on the kernel dts introduced in |
||
Daniel Golle
|
d0a2b3f824 |
mediatek: add Adtran SmartRG SDG-8733A
Specification is similar to other devices of the MT Stuart series: * Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed) * 8 GiB eMMC * 2 GiB DDR4 RAM * 2500M/1000M/100M LAN port * 10000M/5000M/2500M/1000M/100M/10M WAN port * MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi * Renesas DA14531MOD Bluetooth * 2 buttons (Reset, Mesh/WPS) * uC-controlled RGB LED via I2C * 2x LED for the 2.5G port, 3x LED for the 10G port * 3.3V-level 115200 baud UART console via 4-pin Dupont connector exposed at the bottom of the device * USB-C PD power input Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Mikhail Zhilkin
|
f368e2d5ec |
ramips: add support for netis N6
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
Mauri Sandberg
|
fea2264d9f |
ramips: mt7621: Add DNA Valokuitu Plus EX400
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
||
|
John Crispin
|
28d8f33925 |
uboot-envtools: add support for OpenWrt One
Signed-off-by: John Crispin <john@phrozen.org> |
||
George Witt
|
9b33645566 |
ipq807x: add support for TP-Link EAP660 HD v1
Specifications: * SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz) * Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13) * Serial Port: 3v3 TTL 115200n8 * Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax) * Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax) * Ethernet: QCA8081 (10/100/1000/2.5GBASE-T) * Flash: Winbond W29N01HZSINF (128 MiB) * LEDs: 1x Blue Status (GPIO 42 Active High) * Buttons: 1x Reset (GPIO 50 Active Low) Installation Instructions (Serial+TFTP): 1. Solder 4 pin header to JP1 and bridge pads of R58 and R62. 2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively. Be sure to crossover TX and RX. 3. Copy RAM firmware image openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb to TFTP server root, available at 192.168.10.1. 4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the serial console (115200 baud) until autoboot is halted. 5. Run the following commands in the U-boot prompt: # tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb # bootm You may need to type Ctrl+C and Enter before running these commands to clear invisible characters from the buffer. 6. Run the following command in a terminal to copy the sysupgrade image to be installed (check IP address): $ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/ 7. Activate the OpenWrt serial console and run the following commands: # cd /tmp # sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin 8. The AP will reboot and OpenWrt will be successfully installed. Signed-off-by: George Witt <george.witt@nltsproject.org> Link: https://github.com/openwrt/openwrt/pull/15832 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Ivan Pavlov
|
2b2a98b3eb |
uboot-envtools: add u-boot system env config for Xiaomi Redmi AX6S
Adds u-boot config for access to system env variables on this board Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com> Link: https://github.com/openwrt/openwrt/pull/16312 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
Paweł Owoc
|
2c48cda28b |
uboot-envtools: ath79: add Belkin F9K1115v2/F9J1108v2 u-boot env support
Add support for Belkin F9K1115v2/F9J1108v2 u-boot env Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: https://github.com/openwrt/openwrt/pull/16033 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
Roland Reinl
|
2fbffb3643 |
mediatek: Add support for Linksys EA7500 v3
Specification: - MT7629 CPU - MT7531 switch - MT7761N and MT7762N wifi - 256 MB RAM - 128 MB NAND flash with dual-boot partitions - 2 buttons: WPS and reset - 1 WAN port (1G) - 4 LAN ports (1G) - 1 USB port Limitations (same as other MT7629/MT7761N/MT7762N devices): - Wifi is not working - Second core is not working (kernel error message "CPU1: failed to come online") Disassembly: - There are two screws under the front rubber feet and two under the label on the bottom (in the corners towards the back, you should be able to feel them). Serial Interface: - UART pin header is already soldered on the board. Pinning from front to back: 1 - VCC 2 - TX 3 - RX 4 - n/a 5 - GND GPIO: - 1 white LED, connected to GPIO 52 - 1 reset button, connected to GPIO 60 - 1 WPS button, connected to GPIO 58 MAC Adresses: - The MAC address printed on the device label is used for LAN and WAN - The MAC address is stored in the devinfo partition in ASCII format (hw_mac_addr=aa:bb:cc:dd:ee) - 2.4 GHz wifi uses MAC of the device label + 1 - 5 GHz wifi uses MAC of the device label + 2 Flashing: - OpenWrt is only runnig in the first partition of dual boot - To ensure to be able to go back to the factory image, flash the last OEM firmware via OEM web interface. This will ensure that the OEM firmware is present on both partitions - Because of dual boot partitions, flashing via OEM interface is not supported - Start a TFTP server and provide the initramfs image. Default settings: - Router IP: 192.168.1.1 - TFTP server IP: 192.168.1.100 - TFTP file name: 7531.bin - Open the device, connect UART and select " 1. System Load Linux to SDRAM via TFTP." during startup - Adapt the settings to your environment, if required - After initramfs is booted, flash the sysupgrade image Return to OEM firmware: - Run the following commands in OpenWrt to switch to the second partition fw_setenv boot_part 2 fw_setenv bootimage 2 - Reboot the device. OEM firmware will start up again Signed-off-by: Roland Reinl <reinlroland+github@gmail.com> Link: https://github.com/openwrt/openwrt/pull/16067 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Vyacheslav Ivanov
|
7305bf616e |
uboot-envtools: Add support for Orange Pi R1 Plus & LTS
Add support this boards to envtools config This commit integrates the latest changes from new U-Boot, which includes important updates to the DTSI files for the Orange Pi R1 Plus and Orange Pi R1 Plus LTS boards. Signed-off-by: Vyacheslav Ivanov <islavaivanov76@gmail.com> Link: https://github.com/openwrt/openwrt/pull/16090 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Joel Low
|
824f7ea52d |
uboot-envtools: add env settings for ubnt,unifi-6-lr-v3
Using the same configuration as my earlier Unifi 6-LRv2s: ```bash $ cat /etc/fw_env.config /dev/mtd3 0x0 0x1000 0x1000 1 $ fw_printenv arch=arm baudrate=115200 board=mt7622_evb board_name=mt7622_evb bootcmd=bootubnt bootdelay=3 bootfile=uImage cpu=armv7 device_model=U6-LR ethact=mtk_eth ethaddr=<redacted> ipaddr=<redacted> is_ble_stp=true is_default=true loadaddr=0x5007FF28 macaddr=<redacted> serverip=<redacted> soc=mt7622 stderr=serial stdin=serial stdout=serial vendor=mediatek ``` Signed-off-by: Joel Low <joel@joelsplace.sg> Link: https://github.com/openwrt/openwrt/pull/16127 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Kristian Skramstad
|
d62648d58c |
qualcommax: ipq60xx: add support for Cambium Networks XE3-4
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
|
Chukun Pan
|
ee382f65a9 |
uboot-mediatek: add TP-LINK TL-XTR8488 support
Same as TP-Link TL-XDR608x, this router comes with locked vendor loader. Add U-Boot build for replacement loader for this device. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Link: https://github.com/openwrt/openwrt/pull/15930 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Borys Zhukov
|
f25cd55bd1 |
ramips: add support for Netgear WAX214v2
Netgear WAX214v2 is an 802.11ax (Wi-Fi 6) wireless access point. Specifications: * SoC: MediaTek MT7621AT * RAM: 512 MiB * Flash: NAND 128 MiB (ESMT PSU1GA30DT) * Wi-Fi: 2.4/5 GHz 4T4R (MediaTek MT7915E) * Ethernet: 1x 10/100/1000 Mbps LAN * Switch: MediaTek MT7530 (SoC built-in) * LEDs/Keys * Power (green, blue, amber) * LAN (green, amber) * WLAN 2.4GHz (green, blue) * WLAN 5GHz (green, blue) * Reset button * USB: None * UART: Marked J1 on board, 115200 8N1 * Power * 12 VDC, 1.5 A * IEEE 802.3at (PoE+) Load addresses (same as Netgear WAX202): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry MAC addresses as verified by OEM firmware: vendor OpenWrt address eth0 lan label ra0 phy0 label + 2 rax0 phy1 label + 3 Installation: * Flash the factory image by TFTP to the bootloader. NMRP can be used to TFTP without opening the case. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to WAX214v2 GPL source: https://www.downloads.netgear.com/files/GPL/WAX214v2-V1.0.1.5-gpl-src.tar.gz * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax214v2.dts DTS file for this device. Signed-off-by: Borys Zhukov <borys@zhukov.org> Link: https://github.com/openwrt/openwrt/pull/14401 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
Marco von Rosenberg
|
f84a9f7dc0 |
ath79: add support for Huawei AP6010DN
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Tianling Shen
|
f2f428c699 |
mediatek: add ABT ASR3000 support
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Tianling Shen
|
39c824f846 |
mediatek: switch to fitblk for cmcc rax3000m
Use the new fitblk driver. Tested-by: Yangyu Chen <cyy@cyyself.name> Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org> |