PHY as21xxx used on Airoha EN7581 GDM4 requires in-band status control.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/23481
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
After the standalone Airoha PCS driver and pcs-handle binding, wan (gdm2)
and lan2 (gdm4) netdevs probe but do not pass traffic.
Similar to the Aeonsemi PHY it seems also the RTL PHY needs in-band to the
PCS for USXGMII to work correctly. This still needs to be better
investigated but in the meantime lets apply this workaround to restore
traffic.
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
[ improve commit description ]
Link: https://github.com/openwrt/openwrt/pull/23383
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It was discovered that the internal PHY interrupt are not always connected
and PHY link up/down is not correctly detected.
This is the case of the Nokia Valyrian board that suffer from this problem.
To handle this, drop the internal PHY interrupt property from DTSI and add
it only to the Gemtek W1700K DTS where it was reported to work correctly.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The AN7531N SoC has currently problems communicating using `phy_mmd_...`
when irqbalance is active. But when there is a communication error in the
interrupt handler, the interrupt will be disabled. This can usually be seen
in the logs as:
irq 53: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G O 6.12.77 #0
Tainted: [O]=OOT_MODULE
Hardware name: Gemtek W1700K (OpenWrt U-Boot layout) (DT)
Call trace:
dump_backtrace.part.0+0xbc/0xcc
show_stack+0x14/0x20
dump_stack_lvl+0x58/0x74
dump_stack+0x14/0x1c
__report_bad_irq+0x48/0xf8
note_interrupt+0x2f4/0x340
handle_irq_event+0xac/0xe0
handle_simple_irq+0xa8/0xfc
handle_irq_desc+0x30/0x54
generic_handle_irq+0x1c/0x24
airoha_irq_handler+0x90/0xe0
__handle_irq_event_percpu+0x44/0x11c
handle_irq_event+0x40/0xe0
handle_fasteoi_irq+0xb4/0x240
handle_irq_desc+0x30/0x54
generic_handle_domain_irq+0x18/0x20
gic_handle_irq+0x60/0xec
do_interrupt_handler+0x4c/0x84
el1_interrupt+0x30/0x4c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
handle_softirqs+0x98/0x210
__do_softirq+0x10/0x18
____do_softirq+0xc/0x20
call_on_irq_stack+0x30/0x50
do_softirq_own_stack+0x18/0x20
irq_exit_rcu+0x80/0xb8
el1_interrupt+0x34/0x4c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
default_idle_call+0x24/0x34
do_idle+0x98/0xf0
cpu_startup_entry+0x30/0x38
kernel_init+0x0/0x130
console_on_rootfs+0x0/0x64
__primary_switched+0x80/0x88
handlers:
[<000000002b75be58>] irq_default_primary_handler threaded
[<000000006d87ada6>] phy_interrupt
Disabling IRQ #53
This is not a problem with the rtl8261n driver because it is not
registering an interrupt handler. But with the kernel realtek PHY driver, a
interrupt handler is registered which can trigger this problem on bootup.
To avoid is, disable the interrupt and use the PHY polling mode also wit
the upcoming realtek PHY driver support for RTL8261.
Co-authored-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Co-authored-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23078
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some W1700K and XR1701G boards with Realtek RTL8261N/RTL8261BE 10G PHYs
fail to bring up the USXGMII link on cold boot. The PHY enters a bad
state during initialization and the link stays down permanently until
power cycle.
Root cause: the GPIO reset assert/deassert timing (40ms/150ms) is too
short for the RTL8261N to complete its internal firmware load. The OEM
firmware uses 200ms/200ms.
Increase both PHY reset timings to 200ms/200ms to match OEM values.
Confirmed to fix intermittent boot failures on both W1700K (Gemtek)
and XR1701G boards.
Signed-off-by: Ryan Chen <rchen14b@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22564
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With new PCS implementation, the pcs property needs to be updated to the
new name of 'pcs-handle' to correctly work with PCS fwnode
consumer/provider.
Fixes: 4d5f579a81 ("airoha: update PCS node in DTSI for new PCS implementation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update the PCS node in AN7581/AN7583 .dtsi for new PCS implementation.
The #pcs-cell is now needed for the produced/consumer implementation.
Also add entry for USB and PCIe PCS for AN7581 but keep them disabled
by default. USB and PCIe PCS for AN7583 node will be added later once PHY
code will stabilize.
Link: https://github.com/openwrt/openwrt/pull/23271
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The vendor firmware checks for a bmt header in the last 528 erase blocks
of flash. The OpenWrt partition table did not respect that requirement,
and therefore the vendor and openwrt chainloader fight over those blocks
on every boot, potentially corrupting data stored in UBI blocks there.
This commit increases the size of the reserved_bmt partition to avoid
that fight.
Although the vendor bootloader only seems to touch the final 250 erase
blocks[1], the original vendor firmware system partition ended at
0x1be00000[2], so to be conservative, the consensus is to use that as
the end of mtd2 (ubi) partition and leave the last 528 blocks for mtd3
(reserved_bmt).
From https://openwrt.org/toh/gemtek/mxf-w1700k:
[1] OEM bootlog: [ 5.324337] bmt pool size: 250
[2] OEM bootlog: [ 5.478927] 0x000008600000-0x00001be00000 : "system"
Adds a compat_version to warn users to re-install to accomodate the
shrunken mtd2 ubi partition.
Fixed two nits suggested by Claude, zero padding a hex value and removed
an extra space.
Removed the wildcard setting of compat_version for other boards, as
suggested by Robert Marko, set compat_version only for the w1700k.
Reported-by: Loïc Yhuel <loic.yhuel@gmail.com>
Signed-off-by: Russell Senior <russell@personaltelco.net>
Link: https://github.com/openwrt/openwrt/pull/23061
Signed-off-by: Robert Marko <robimarko@gmail.com>
The audio should only be enabled when the sound
node is enabled. This fixes the following error:
an7581-audio 1fbe2200.afe: probe with driver an7581-audio failed with error -2
Fixes: 7b55651 ("airoha: enable I2S sound driver and add nodes for eMMC RFB board")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/22660
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Airoha AN7581 EVB board switched to full UBI support. Update the
partition table to reflect the new implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Generalize the eMMC DTS to common node and add a variant with the Kite WiFi
chip installed. Also rename the eMMC model name and add the Eagle name to
it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add specific DTSI for NPU firmware based on the supported WiFi chip and
update the supported device by including the relevant new DTSI.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop airoha,x2-mode related property from the DTSI and enable them only in
the relevant devices that use a PCIe0 line. x2-mode should be enabled only
for the WiFi card that would use it as it might cause problem for WiFi card
that expect 2 single PCIe x1 line instead of a single PCIe x2 line.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for Nokia Valyrian based on Airoha AN7581 SoC.
Device specification
--------------------
SoC Type: Airoha AN7581
RAM: 2x DDR4 Nanya NT5AD256M16E4-JR (1GB)
Flash: eMMC Macronix MX52LM08A11XVW (1GB)
Ethernet: 3x gigabit via AN7581, 1x 10g via AS21x1x, 1x SFP cage
Wi-Fi: MT7996 - BE19000
LEDs: 11 LED via 2x 74HC595 shift register
Button: Reset, WPS, WiFi
USB ports: 1x 2.0
Miscellaneous: 1x Power Monitor via RTQ6059, 2x FXS port
Device is unfused and is originally flashed with Airoha SDK bootloader
that require signed images.
Bootloader is username/password protected and use the leaked auth combo
that can be found online.
From the bootloadet instruction on how to flash custom bootloader are:
1. mmc erase 0 0x800
2. tftpboot 192.168.1.10:airoha/an7581/openwrt-airoha-an7581-nokia_valyrian-preloader.bin
3. mmc write $loadaddr 0x4 0xfc
4. tftpboot 192.168.1.10:airoha/an7581/openwrt-airoha-an7581-nokia_valyrian-bl31-uboot.fip
5. mmc write $loadaddr 0x100 0x700
It's also possible to use the Emergency Recovery procedure:
From powered OFF device:
1. Keep the reset button pressed (middle button)
2. Power on the device
3. Notice the "Press x" prompt
4. Press x
5. Notice the "C" char waiting for XMODEM load
6. Load the preloader binary with XMODEM protocol
7. Notice the "Press x to load BL31 + U-Boot FIP"
8. Press x
9. Notice the "C" char waiting for XMODEM load
10. Load the fip binary with XMODEM protocol
11. You are now in U-Boot loaded from serial
12. Follow normal procedure to flash bootloader
Due to BOOTROM limitation. the device can't have a standard GPT table
implementation. Because of this fixed-partitions are used to handle this.
U-Boot still doesn't have support for this (it's planned) and currently to flash
and load and image it's needed to write and read from static address in eMMC.
The GPT partition table follow Prpl guidelines with dual partition table with
kernel and rootfs split.
The address for kernel is 0xb00000 and the address for rootfs is 0x1b00000.
Link: https://github.com/openwrt/openwrt/pull/21761
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit adds support for Gemtek (Centurylink/Lumen/Quantum Fiber)
W1700K.
Device specification
--------------------
SoC Type: Airoha AN7581
RAM: ESMT M16U8G16512A (2GB)
Flash: Winbond 25N04KVZEIR (512MB)
Ethernet: 2x gigabit via AN7581, 2x 10g via RTL8261N
Wi-Fi: MT7996 - BE19000
LEDs: 1 LED, power/status
Button: Reset
USB ports: None
Bootloader: U-Boot 2014.04-rc1 (Jun 12 2024 - 08:14:34) AXON 2.0
Fan: 1x controlled by Nuvoton NCT7511Y
This device is pretty useless with the stock firmware as it requires an
account to completely set it up. Additionally, the vendor bootloader is
signed and uses Airoha/Mediatek's BBT/BMT for bad block management on
the flash. It does not support UBI, thus kernel updates are subject to
BMT/BBT which OpenWrt does not support. In turn, if a kernel update
happens and a block is marked bad in the process, the device will fail
to boot and will need to be recovered via serial.
The workaround is to chainload U-Boot in place of the kernel, as it
should not need frequent updates and thus should not cause BBT/BMT to
misbehave and soft-brick the device. Upstream U-Boot supports loading
a FIT image from UBI, so we create a UBI partition for the new u-boot
env, FIT image and factory data. This way, bad blocks are managed by UBI
instead, which will not soft-brick the device should a block be marked
bad during a normal OpenWrt update. Users wishing to update U-Boot can
do so, but should be prepared to recover if a block goes bad.
Because the device is not useful with stock firmware, this is a one-way
ticket for most users and reverting will not be documented.
The following steps can be used to install OpenWrt on the W1700K.
Connect to serial console. There is a Torx T10 screw underneath the QR
code printed onto the label. Then, pry between the gray and white
plastic, starting by the ports on the back. There are clips arount the
entire device. Starting closest to the screw next to the UART header,
TX - GND - VCC - N/A - RX. The bootloader can be interrupted by
pressing any key.
Configuring Vendor Bootloader and Installing U-Boot Chainloader:
The bootloader's default bootcmd will only run a signed image. However,
we can still bootm our own image from flash.
NOTE: The vendor's ethernet drivers are flaky. You may have to reboot
and try the tftpboot part several times for it to work.
- setenv one flash read 0x600000 0x1000000 \$loadaddr
- setenv two "; bootm"
- setenv bootcmd "$one$two"
- setenv one
- setenv two
- saveenv
- setenv serverip 192.168.1.10; setenv ipaddr 192.168.1.1; tftpboot
0x89000000 openwrt-airoha-an7581-gemtek_w1700k-ubi-chainload-uboot.itb
- flash erase 0x600000 0x100000
- flash write 0x600000 0x100000 0x89000000
- reset
The device will now reboot into the U-Boot chainloader.
Loading the W1700K UBI Installer:
The installer can be downloaded at
https://github.com/hurrian/w1700k-ubi-installer/releases
- Boot the installer via the TFTP option in the U-Boot menu. This
process is automatic, though you may be prompted to answer some
questions.
- Once it is done, you may upgrade to your preferred build.
- For more information: https://github.com/hurrian/w1700k-ubi-installer
For those wishing to explore the stock firmware:
Rooting Stock FW (for making backups, recommended):
- Boot the router and watch serial console until presented with failsafe
mode. Enter it (f + enter).
- mount_root
- Change the root password (passwd).
- Open /etc/config/axon_platform_manager and set sshServerEnable,
localAccessEnable and remoteAccessEnable to 1.
- Search for "SSH". You'll find a long string with 3 matches such as
Enabled%25252c1%25252cSSH%Drop. Change any instances of "Disabled"
preceding SSH to "Enabled" and any instances of "Drop" to "Accept"
that follow SSH. Same for "Local SSH" and "Remote SSH".
- Set /etc/config/dropbear to:
config dropbear
option PasswordAuth 'on'
option RootPasswordAuth 'on'
option Port '22'
- Reboot.
- Connect 10g WAN port to existing network and SSH in with the password
you set.
- SSH into rooted stock fw.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17869
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce the capability to read the firmware binary names from device-tree
using the firmware-name property if available.
This is a preliminary patch to enable NPU offloading for MT7996 (Eagle)
chipset since it requires a different binary with respect to the one
used for MT7992 on the EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/22289
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initialize NPU Block Ack memory region if reserved via DTS.
Block Ack memory region is used by NPU MT7996 (Eagle) offloading.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/22289
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix two hardware initialization issues in the EN7581 PCIe controller
and add support for x2 (2-lane) link mode.
Fixes:
The upstream EN7581 PCIe initialization writes EQ presets and PIPE
configuration registers before clk_bulk_prepare_enable(). Since the
MAC clocks are not yet running at that point, these register writes
are silently dropped, leaving the hardware with default values. This
can cause link training failures or suboptimal equalization.
Additionally, after link training the MAC may only advertise Gen1-Gen2
capability in the Link Capabilities 2 register despite the PHY being
configured for Gen3. A serdes reset toggle forces the MAC to re-read
PHY capability, recovering Gen3 8GT/s link speed.
Both issues are addressed by separating PERST from the clock callbacks
(patch 911), allowing the PCIe controller driver to properly sequence
PERST, clock enable, and register writes (patch 912).
New feature:
PCIe x2 mode support for EN7581 using the NP_SCU system controller
for serdes mux routing, PERST management, and lane configuration.
Both bonded MACs are configured for x2 operation with proper EQ
presets before link training begins.
Signed-off-by: Ryan Chen <rchen14b@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21978
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MT7531 has an incorrect interrupt number described in the DTS.
This commit also adds PHY interrupts. They work the same as on
the MT7988.
Tested on Gemtek W1700k.
Suggested-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21016
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Let node unit address same as reg.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Different boards use different port map. For example, some board may use
a GE port as WAN. So defining the led label in board-level is better.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Different boards use different port map. Defining the port labels in
board-level is better.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some board only use some of them, so enable as necessary in
board-level dts.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix the unit-address of the scuclk node.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No functional changes intended.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable I2S sound driver and add nodes for eMMC RFB board since it's the
one that always have the I2C codec and can use the sound card.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use latest patch version
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20400
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no reason not to do this.
Use the following commands to enable hardware offloading:
uci set firewall.@defaults[0].flow_offloading='1'
uci set firewall.@defaults[0].flow_offloading_hw='1'
uci commit
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20484
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable USB node on eMMC RFB board and disable USB2 3.0 port to make the
3rd PCIe line correctly work.
This is needed to prevent the xHCI driver to mess with PCIe by
configuring the USB2 3.0 port. Port will still be detected but won't be
configureed by the driver and won't have PHY to configure for.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The 3rd PCIe line use the USB2 serdes for PCIe operation. Correctly set
it to the DT node so that the mode can be correctly set in the PHY
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some SoC might use the Serdes for the second USB port as a 3rd PCIe
line (with the SSTR register correctly setup).
Add the node for the 3rd PCIe card and enable for the eMMC RFB board.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Airoha AN7581 eMMC RFB board mount 2 Aeonsemi AS21xxx PHY. One is
usually connected to GDM4 and the other is optionally connected to GDM2.
Add the relevant nodes to support the one connected to GDM4.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add relevant nodes for NPU support for Airoha AN7583 and enable the
kernel config to enable support in the Airoha Ethernet driver.
NPU firmware is scheduled to be upstreamed to linux-firmware and will be
added once present upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
While adding support for Airoha AN7583, it was forget to push the EMMC
DTS while defining the variant in the image Makefile.
Add the missing DTS to fix image creation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
On the Airoha AN7583 EVB there are 2 Aeonsemi AS21xxx PHY but only the
one connected to Serdes Ethernet is usable as the other connected to
Serdes PON is not actually HW connected (as the serdes is connected to
the BOSA port)
Add comments and disable the relevant PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There are two spi drivers for en7523/an7581/an7583:
* en7581-snand (spi-airoha-snfi.c)
* en7523-spi (spi-en7523.c)
The first one supports DMA, but until recently it has several nasty
issues. The second do things properly but does not support DMA.
Recently the first driver was greatly improved, so there is no sence
keep both drivers anymore.
This patch removes en7523-spi driver and use DMA capable driver instead.
Unfortunately there is a nasty en7523 specific issue.
We found that some serial console may pull TX line to GROUND during board
boot time. Airoha uses TX line as one of it's BOOT pins. This will lead
to booting in RESERVED boot mode. It was found that some flashes operates
incorrectly in RESERVED mode if DMA used.
This patch also adds a hack that turns off DMA and prints big fat warning
if booting in reserved mode was detected. This slow down flash operations
but does not kill your data.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20365
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us use more easily port en7581 drivers to en7523.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20365
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing syscon compatible for scuclk node.
Fix the unit-address of the scuclk node.
This fixes the pcs driver error:
airoha-pcs 1fa08000.pcs: probe with driver airoha-pcs failed with error -22
airoha-pcs 1fa09000.pcs: probe with driver airoha-pcs failed with error -22
Fixes: c3d70b1 ("airoha: en7581: Add support for external PHY")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce initial support for Airoha AN7583 SoC and add all the required
patch for basic functionality of the SoC.
Airoha AN7583 is based on Airoha EN7581 SoC with some major changes on
the PHY handling and Serdes. It can be see as a lower spec of EN7581
with modern and simplified implementations.
All the patch are sent upstream and are pending revision. Support for
PCIe and USB will come later as soon as DT structure is accepted
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This add a pending version of the Airoha PCS driver to add support for
External PHY. The Airoha PCS driver will receive some minor modification
once we the PCS subsystem will be defined upstream.
Add all the required node for GDM2 and GDM4 and enable the PCS config.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
No functional changes intended.
Fixes warning:
/linux/arch/arm64/boot/dts/airoha/en7581-gemtek-w1700k.dtb: i2c1@1fbf8100 (mediatek,mt7621-i2c): status: 'oneOf' conditional failed, one must be fixed:
['disable'] is not of type 'object'
'disable' is not one of ['okay', 'disabled', 'reserved', 'fail', 'fail-needs-probe']
from schema $id: http://devicetree.org/schemas/dt-core.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the NPU and reserved memory node for AN7581 dtsi since it's not
supported.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace PCIe patch with upstream version and update DTS with new PBUS
CSR property now required.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
PHY2 led1 is configured to control PHY1's LED. Change it to PHY2.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18361
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace eMMC support with upstream version where we declare dummy clock
and dummy regulator instead of a specific compatible. Also drop the
downstream patch for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
