nvmem-layout is used instead of the older nvmem-cells. Seems to be a
copy/paste mistake.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23512
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The gmac1 is not used and doesn't have any mac address configured. The
gmac0 has the nvmem-cells set and can actually be used to retrieve the
correct mac address.
Fixes: c7c54f3134 ("ramips: add support for Plasma Cloud PAX1800-Lite")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/23441
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specificaitons:
- MediaTek MT7621AT SoC
- 256 MB RAM
- 16MB SPI NOR Flash
- 256MB NAND (split in half for firmware fallback)
- 4x 10/100/1000 Mbps Ethernet, with passive PoE support on LAN1
- WLAN : MediaTek dual-band WiFi 5
- 2.4 GHz : b/g/n, MIMO 2x2
- 5 GHz : n/ac, MIMO 2x2
- Quectel EG060K-EA 4G CAT6 modem
- 2.0 USB Type-A HOST port
- 1x Digital input
- 1x Digital output
- 2x SIM slot (can be swapped via GPIO)
GPIO:
- 1 button (Reset)
- 14 LEDs (power, 4x WAN status, Wifi 2G, Wifi 5G, 3G, 4G, 5x RSSI)
- 3 Modem control (power button, reset, sim select)
- 1 Digital input
- 1 Digital output
Installation
------------
Notice: update OEM firmware to 7.19 or later, earlier versions will
fail to flash openwrt factory firmware.
1. Check from which partition the device is currently running from
$ cat /proc/bootconfig/chosen
In case this output reads rutos-b, install a software update from
Teltonika first. After upgrade completion, check this file now reads
rutos-a before continuing.
2. Download the *-squashfs-factory.bin firmware image
3. Flash firmware image via WEB interface
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile connection:
- EG060K-EA:
Execute AT commands:
echo -ne 'AT+QCFG="usbnet",2\r\n' > /dev/ttyUSB2
echo -ne 'AT+CFUN=1,1\r\n' > /dev/ttyUSB2
Use ModemManager to establish mobile connection.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Specifications:
- MediaTek MT7621AT SoC
- 256 MB RAM
- 16MB SPI NOR Flash
- 256MB NAND (split in half for firmware fallback)
- 2x 10/100/1000 Mbps Ethernet, with passive PoE support on LAN
- WLAN : MediaTek dual-band WiFi 5
- 2.4 GHz : b/g/n, MIMO 2x2
- 5 GHz : n/ac, MIMO 2x2
- Quectel RG520N-EB 5G R16 modem (RUTM30) or RG500U-EB 5G (RUTM31)
- 1x Digital input
- 1x Digital output
- 2x SIM slot (can be swapped via AT commands)
- eSIM
- TPM
GPIO:
- 1 button (Reset)
- 3 LEDs (power, 2 RGB)
- 3 Modem control (power button, reset, eSIM switch)
- 1 Digital input
- 1 Digital output
- 1 TPM enable
Installation
------------
Notice: update OEM firmware to 7.19 or later, earlier versions will
fail to flash openwrt factory firmware.
1. Check from which partition the device is currently running from
$ cat /proc/bootconfig/chosen
In case this output reads rutos-b, install a software update from
Teltonika first. After upgrade completion, check this file now reads
rutos-a before continuing.
2. Download the *-squashfs-factory.bin firmware image
3. Flash firmware image via WEB interface
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile connection:
- RG520N-EB:
Use "ModemManager" to establish mobile data connection.
- RG500U-EB:
echo -ne 'AT+QNETDEVCTL=1,3,1\r\n' > /dev/ttyUSB2
Create DHCP interface with usb0 device.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Specifications:
- MediaTek MT7621AT SoC
- 256 MB RAM
- 16MB SPI NOR Flash
- 256MB NAND (split in half for firmware fallback)
- 5x 10/100/1000 Mbps Ethernet, with passive PoE support on LAN1
- WLAN : MediaTek dual-band WiFi 5
- 2.4 GHz : b/g/n, MIMO 2x2
- 5 GHz : n/ac, MIMO 2x2
- Quectel RG520N-NA 5G R16 modem (RUTM50) or RG500U-EB 5G (RUTM51)
- 2.0 USB Type-A HOST port
- 1x Digital input
- 1x Digital output
- 2x SIM slot (can be swapped via AT commands)
GPIO:
- 1 button (Reset)
- 13 LEDs (power, 4x WAN status, Wifi 2G, Wifi 5G, 3G, 4G, 5G, RSSI
1,2,3)
- 2 Modem control (power button, reset)
- 1 Digital input
- 1 Digital output
Installation
------------
Notice: update OEM firmware to 7.19 or later, earlier versions will
fail to flash openwrt factory firmware.
1. Check from which partition the device is currently running from
$ cat /proc/bootconfig/chosen
In case this output reads rutos-b, install a software update from
Teltonika first. After upgrade completion, check this file now reads
rutos-a before continuing.
2. Download the *-squashfs-factory.bin firmware image
3. Flash firmware image via WEB interface
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile connection:
- RG520N-NA:
Use "ModemManager" to establish mobile data connection.
- RG500U-EB:
echo -ne 'AT+QNETDEVCTL=1,3,1\r\n' > /dev/ttyUSB2
Create DHCP interface with usb0 device.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
The RG-EW1300G is a router with 1 x WAN and 3 x LAN gigabit ports.
The router runs on Ruijie OS by default.
- Specifications:
* SoC: MT7621A
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* WiFi0: Mediatek MT7615 2.4GHz 802.11b/g/n
* WiFi1: Mediatek MT7615 5GHz 802.11ac
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console - As marked on PCB, baudrate is 57600. DO NOT CONNECT 3.3V.
* Buttons: Reset, WPS.
* LED: Programmable LEDs via GPIO working for Red+Green status, and Mesh/WPS at the rear of the chassis.
- Default Flash:
```
GD25Q128C(c8 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
6 cmdlinepart partitions found on MTD device raspi
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000050000 : "u-boot"
0x000000050000-0x000000060000 : "u-boot-env"
0x000000060000-0x000000070000 : "Factory"
0x000000070000-0x000000080000 : "product_info"
0x000000080000-0x000000090000 : "kdump"
0x000000090000-0x000001000000 : "firmware"
0x00000031a847-0x000001000000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs_data" created automatically, ofs=0xae0000, len=0x520000
0x000000ae0000-0x000001000000 : "rootfs_data"
register mt_drv
```
```
cat /proc/mtd
dev: size erasesize name
mtd0: 00050000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "factory"
mtd3: 00010000 00010000 "product_info"
mtd4: 00010000 00010000 "kdump"
mtd5: 00f70000 00010000 "firmware"
mtd6: 0028a847 00010000 "kernel"
mtd7: 00ce57b9 00010000 "rootfs"
mtd8: 00520000 00010000 "rootfs_data"
```
- Installation:
1. Open the case, solder to the marked 4 pin header
2. Connect it to a USB-UART TTL (do not connect to 3.3v)
3. Open a terminal with baud 57600.
4. Power on device, and repeatedly press "2" key to catch bootloader option
5. Set IP, TFTP server IP, and image file to load (eg, openwrt-ramips-mt7621-ruijie_rg-ew1300g-v1-squashfs-sysupgrade.bin)
6. System will reboot into OpenWRT.
Signed-off-by: Matt Brent <git@mattzfiber.co.za>
Link: https://github.com/openwrt/openwrt/pull/21864
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a nonsensical binding that's not implemented anywhere.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23137
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
* CPU: MediaTek MT7628AN (580 MHz)
* Flash: GigaDevice GD25Q128CSIG (16 MiB)
* RAM: Winbond W9751G6KB-25 (64 MiB)
WikiDevi page: <https://wikidevi.wi-cat.ru/Keenetic_City_(KN-1510)>
How to flash:
* Configure TFTP server with IP address 192.168.1.2/24
* Serve OpenWrt factory image as "KN-1510_recovery.bin"
* Connect the PC to router's LAN port, hold the reset button and power
the router up. When the power LED starts blinking release the
button.
The same instructions apply to OEM firmware, except one can take it
from osvault.keenetic.net
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/22404
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EDUP EP-RT2983 comes with a factory installed version of OpenWrt 23.05
with device name "netis,n6".
Specification
--------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (Toshiba)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x WiFi (green)
1x Mesh/WPS (green); flashing green during boot
3x LAN (green)
1x WAN (green); flashing red during upgrade and failsafe
- Power : 12 VDC 1A
Installation
-------------
1. Log in to LuCI
2. Go to System, Backup / Flash Firmware
3. If desired, backup the current system by saving (all) the mtdblock
contents.
4. Flash new firmware image, select Flash image.
5. Browse and select the sysupgrade file
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-sysupgrade.bin"
and then Upload.
6. Unselect "Keep settings and retain the current configuration"
Note: All settings will be reset to default. WiFi is not enabled by
default so a connection via Ethernet is necessary to log in and set up.
7. Allow "Force upgrade" (tick the box if there is one), or press Continue
if there is no box to tick. This is because the name is now
"edup,ep-rt2983" as it should have been from the start.
8. Proceed to flash. Wait for reboot and keep power connected.
9. After reboot, default address to access LuCI is 192.168.1.1 with
no password
Recovery (UART)
----------------
1. Remove the 4 screws on the bottom and pry open the cover.
2. Connect serial adapter to the unpopulated serial header pins
TX, RX, GND near the WPS button. Do not connect VCC.
3. Start serial terminal (e.g. minicom, screen, etc) on the computer and
turn on the router.
4. As prompted, hit any key to stop autoboot.
5. Enter 2 to select "2. Upgrade firmware"
6. Enter 0 to select "0 - TFTP client (Default)"
7. Accept the defaults by pressing Enter for
"Input U-Boot's IP address: 192.168.1.1",
"TFTP server's IP address: 192.168.1.2",
"Input IP netmask: 255.255.255.0"
8. Assign your PC's Ethernet port a static IP 192.168.1.2 with netmask
255.255.255.0 and connect to a LAN port on the router using the
Ethernet cable. Disconnect all other network connections (e.g. WiFi) on
the computer.
9. Serve the factory image
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-factory.bin" using
a TFTP server, e.g. tftpd64. For convenience, the filename can be renamed
to something shorter.
10. In the serial terminal, when prompted "Input file name:", enter the
filename from the previous step and press Enter.
11. The factory image will be flashed as indicated. Wait for reboot.
MAC addresses prototype
------------------------
+---------+---------------------+
| | MAC example |
+---------+---------------------+
| LAN | CC:D8:1F:47:xx:yy |
| WAN | CC:D8:1F:47:xx:yy+1 |
| WLAN 2G | CC:D8:1F:17:xx:yy+2 |
| WLAN 5G | CC:D8:1F:77:xx:yy+2 |
+---------+---------------------+
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the Wavlink "Halo Base Pro".
SOC: MT7621DAT
RAM: 128MiB
Flash: 16MiB NOR
WiFi: MT7603EN + MT7613BEN
Buttons:
- The touch sensor was originally for WPS, but this has been moved to the
pair button which is no longer used to prevent accidental touches
LEDs:
- On original firmware, the status LEDs light up as follows:
- Purple = booting, Blue = working, Red = error
Partitions:
- factory contains unique WiFi EEPROM and default MAC addresses
- vendor partition has an unknown purpose
Stock MAC address allocation:
- LAN1: xx:xx:xx:xx:xx:80
- LAN2/WAN: xx:xx:xx:xx:xx:81
- WiFi 2.4G: xx:xx:xx:xx:xx:82
- WiFi 5G: xx:xx:xx:xx:xx:83
LAN Ports:
- lan1 is the normal white LAN port
- lan2 is labelled "LAN/Backhaul", which can either be LAN or WAN.
- Since this device is intended to be part of a mesh, this will usually
be a LAN port, hence why it's assigned to lan2 here
Notes:
- I've chosen "Halo Base Pro" as the device model, despite the website URL
showing WL-WN535M3, as the label only states "Halo Base Pro".
- Only the 5GHz WiFi address is labelled on the device
Signed-off-by: William Latter <williamlatter77@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22400
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compared to the "mediatek,mt8173-xhci", this is a more generic and
reasonable compatible string. On the driver side, they are identical.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The USB t-phy driver includes some magic register init values. This
should be beneficial for the USB stability and performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Z-ROUTER ZR-2662 (also known as Routerich
AX1800 V2) wireless WiFi 6 router.
Hardware specification
---------------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Note: This device is similar to Z-ROUTER ZR-2660, but with minor hardware
revisions. The firmware and configuration are compatible.
Signed-off-by: xingchi <juncaixingchi2026@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21524
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB NOR
- RAM: 64 MiB DDR2
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN/LAN, 1x 10/100 LAN (MT7628)
- Build-in LTE Modem: MeigLink SLM770A
4G Cat. 4 (150/50 Mbps)
- Buttons: 1x Reset, 1x wps
- LEDs: Front: 1x Red, 1x White,
Back: 3x White 4G signal strengh
- Serial console: unpopulated header, 115200 8n1
- Power: USB-C
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Migration to OpenWrt:
- Download the RSA signed intermediate firmware from the Cudy website:
`openwrt-ramips-mt76x8-cudy_lt300-v3-squashfs-flash.bin`
- Connect computer to LAN and flash the intermediate firmware via OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The dt-bindings suggest using "^serial(@.*)?$" as the node name.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is necessary to make it work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
<>, <> is the preferred way to specify multiple entries.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove unnecessary properties as there is no
reg property in child node.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22592
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Xiaomi Redmi/Mi Router AC2100 does have the correct label mac on the WAN interface.
This MAC is available as gmac1.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/22567
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adjust the memory remap range according to the mt7621 programming
guide to ensure that the driver can correctly access the peripheral
registers.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22467
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A size of 600 is incomplete in that calibration data is not included,
resulting in low TX power.
Fixes: 64dae105 ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22459
Signed-off-by: Robert Marko <robimarko@gmail.com>
The dtsi used handles a bunch of non-DBDC platforms where the
assignments are correct. The 3040-a1 is different as there are 3 instead
of 2 wifi interfaces and WAN needs to be incremented by 1.
Remove userspace wifi assignmwent which was needed before per band nvmem
was supported.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21977
Signed-off-by: Robert Marko <robimarko@gmail.com>
The upstream MediaTek PWM driver requires these clock sources to
work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22214
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Since the u-boot ethaddr variable is quoted, we cannot use it.
Use mac-base instead to specify in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Removes deprecated userspace handling.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use clock index macros defined in dt-bindings header to improve the
code readability.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22163
Signed-off-by: Robert Marko <robimarko@gmail.com>
Given that Linksys is the same brand and probably use the same OEM, it
stands to reason all devinfo hw_mac_addr implementations are the same.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22092
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove incomplete SPI flash definitions from affected device tree files.
These fragments only defined address-cells and size-cells without any
actual flash configuration (partitions, compatible string, etc.).
After applying openwrt/openwrt#20942 ("kernel: of: fix bad cell count error
for SPI flash node"), the kernel properly handles SPI flash nodes without
requiring these incomplete definitions in device-specific DTS files.
This cleanup eliminates unnecessary code that was likely a workaround for
the previous kernel issue.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22036
Signed-off-by: Robert Marko <robimarko@gmail.com>
The D-Link DIR-1360 A1 is an AC1300 router based on the MT7621AT SoC.
Specifications :-
* SoC: MediaTek MT7621AT
* RAM: 256 MB DDR3
* Flash: 128 MB SPI NAND (Winbond W29N01HV)
* WiFi: MT7615D (2.4 GHz + 5 GHz DBDC)
* Ethernet: 5x 10/100/1000 Mbps (1x WAN, 4x LAN)
* USB: 1x USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (White/Orange), Internet (White/Orange), USB, 2.4G/5G WLAN
MAC addresses are retrieved from the 'factory' partition via NVMEM.
LAN: 0xe000 (gmac0)
WAN: 0xe006 (gmac1)
WLAN: 0xe00c (pcie0)
Flash Instruction :-
1-Set a static IP on your PC (e.g., 192.168.0.10, Gateway 192.168.0.1).
2- Power off the router and connect your PC to a LAN port.
3- Hold the Reset button and power on the router; continue holding for 5 seconds.
4- Access the Recovery UI at http://192.168.0.1 in your browser.
5- Upload the OpenWrt factory.bin image and wait for the reboot.
With these definitions in place, the DIR-1360 A1 boots reliably, exposes all hardware features correctly, and can be flashed via both the OEM recovery interface and standard OpenWrt upgrade paths.
Signed-off-by: Aryaman Srivastava <aryamansrivastava895@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the Cudy LT400E v1,
an indoor 4G/LTE WiFi router.
It has 4x10/100 Mbps Ethernet ports, a 2.4 GHz radio,
and a Quectel 4G/LTE EC200A modem.
Hardware:
SoC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
Ethernet: 4x10/100 Mbps
WiFi: 2.4 GHz (embedded MT7628, 802.11n)
WWAN: Quectel EC200A-EL 4G/LTE Cat 4 modem
SIM: nano-SIM slot
Buttons: 1 Reset button, 1 WPS button
LEDs: 10x (blue)
Power: 12 V DC barrel jack
Installation:
The stock firmware is a customized variant of OpenWrt, which implements
a signature check that only allows flashing official firmware. Cudy
offers, on their website [1][6], intermediate OpenWrt firmware images
which do not implement the signature check. After flashing the
intermediate image, the upstream (i.e., official) OpenWrt image can be
installed. See the device's entry in OpenWrt's Wiki for more details [2].
Cellular network:
The Quectel EC200A modem is internally connected to the SoC via USB, and
operates in ECM mode, supported by the CDC Ether driver [3]. When
inserting a SIM card in the slot, if no PIN is needed, the network
interface "usb0" is brought up and the cellular connection works out of
the box. To interact with the modem directly (unlock the PIN, change APN
and PDP settings, etc.), AT commands can be sent with picocom to serial
port /dev/ttyUSB2 [4].
Recovery:
The stock firmware can be recovered via TFTP, as the bootloader (based
on U-Boot) implements a recovery client. Set up a TFTP server on your
computer with IP 192.168.88.1/24 serving the stock firmware from Cudy's
website renamed to "recovery.bin". Press the Reset button (keep it
pressed), power on the device, wait for the TFTP server to send the
recovery.bin file, then release the Reset button. The router will take a
couple of minutes to reboot and set up the stock firmware. See the
device's entry in OpenWrt's Wiki for more details [2].
Discussion:
Use the dedicated thread in OpenWrt's forum to discuss any aspects [5].
Acknowledgments:
The code to support this device is largely based on the sources kindly
provided by Cudy in compliance with the GPL license. Thanks for
supporting the OpenWrt community.
Links:
[1] https://www.cudy.com/blogs/faq/openwrt-software-download
[2] https://openwrt.org/toh/cudy/lt400e_v1
[3] https://openwrt.org/docs/guide-user/network/wan/wwan/ethernetoverusb_cdc
[4] https://openwrt.org/docs/guide-user/network/wan/wwan/at_commands
[5] https://forum.openwrt.org/t/242466
[6] https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj
Co-authored-by: rogerpueyo <roger.pueyo@guifi.net>
Signed-off-by: Kamil Jońca <kjonca@onet.pl>
Link: https://github.com/openwrt/openwrt/pull/21246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The gmac definition has an offset of 1 at the moment. This leads to an
off by one error in downstream projects that rely on the package label mac.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Link: https://github.com/openwrt/openwrt/pull/21543
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename them to follow the rtl836x driver gpiod changes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21143
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Migrate wifi compatible from ralink,rt2880-wmac to ralink,rt2880-wifi to
align to new 6.18 backports version.
Link: https://github.com/openwrt/openwrt/pull/20964
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit adds support for the Teltonika RUT976, part
of the RUTE series, which is very similar to the RUT956.
The RUT976 now has a 5G modem and the flash size has doubled.
Specification:
- MediaTek MT7628AN SoC
- 128 MB RAM
- 32MB Flash
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- MediaTek MT7628AN 2.4 GHz 802.11n WiFi
- Quectel RG255C 5G modem
- GNSS
- RS232, DB9 connector, Cypress ACM via USB, /dev/ttyACM0
- RS485 /dev/ttyS1
- microSD card slot
- 2.0 USB Type-A HOST port
- analog 0-24V input (MCP3221)
- Relay
- 2x Digital input
- 2x Digital output
- 2x SIM slot (can be swapped via GPIO)
- eSIM (depends on hardware configuration, can be swapped via GPIO)
GPIO:
- 1 button (Reset)
- 7 LEDs (power, status green/red, RSSI 1,2,3,4,5)
- 5 Modem control (power button, reset, status, SIM select, eSIM select)
- 2 Digital input
- 2 Digital output
- 1 Isolated input
- 1 RS485 tx enable
- 1 RS485 rx enable
- 1 Relay
- 1 Data Carrier Detect (DCD)
Flashing via OEM WebUI:
1. Download the firmware image *-squashfs-factory.bin
2. Upload firmware image via OEM WebUI firmware update, do not keep settings
To revert back to OEM firmware:
https://wiki.teltonika-networks.com/view/Bootloader_menu
Mobile data connection:
Create proto qmi interface.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/20933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce mt7628an_teltonika_rut9m.dtsi to hold the SPI-NOR flash
definition and partition layout specific to the RUT9M series.
This refactor prepares for supporting the Tetonika RUT976
(part of the RUTE series), which shares most hardware with
RUT9M devices but has a different flash layout.
Update RUT9x1 and RUT9x6 DTS files to include the new dtsi.
Existing RUT9M devices remain unchanged.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/20933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628DAN
- Flash: 16 MB
- RAM: 64 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN/LAN, 3x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (PWR): Always Off
Modem (NET): GPIO/3 active-low
LAN: Always On
RF (Modem Signal): GPIO/2 active-low
WIFI: GPIO/44 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using TTL:
1. Connect the board to the computer via TTL.
2. Enter original firmware failsafe mode.
3. Use wget download firmware to board /tmp
4. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h8850-v20-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8850-v20-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20259
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The reg value says it should be wifi@1,0, not wifi@0,0.
Should fix dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20351
Signed-off-by: Robert Marko <robimarko@gmail.com>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
