CONFIG_JUMP_LABEL is no longer meant to be set explicitly in target
kernel configs after 3be02c118f ("kernel: enable static key").
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/23293
Signed-off-by: Robert Marko <robimarko@gmail.com>
This symbol is selected by CONFIG_BPF, which was already enabled
on generic config-6.18.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is selected by CONFIG_BPF, which was already enabled
on generic config-6.12.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol depends on the specific CPU type, so we should not
set it globally.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
As preparation for enabling 6.18 kernel, rename the existing config to a
version specific 6.12 config.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Now that DCB is enabled by default, it makes sense to include it on
lan969x.
While we are here, lets include ip-bridge as these devices are switches
and the Busybox applet does not expose enough functionality.
These devices have no space constraints.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Due to PTP conflicts with CONFIG_ALL_KMODS which causes the end images
to end up with no switchdev driver included, lets switch to using the
switchdev and PHY drivers as modules instead.
Fixes: 88a404a2d1 ("microchipsw: add support for Microchip LAN969x switches")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Novarq Tactical 1000 is a LAN9696 based switch.
Specifications:
* CPU: Microchip LAN9696 switch SoC
* DRAM: 2GB DDR4
* Storage:
* 32MB QSPI NOR
* 16GB eMMC
* Networking:
* 24 x 10/100/1000 RJ45 via LAN8804 Quad PHY-s over QSGMII
* 4 x 100/1000/2500/5000/10000 SFP+ ports
* 1 x 10/100/1000 management RJ45 via LAN8840 PHY over RGMII (U-Boot too)
* USB: 1 x USB2.0 Type-A
* Management via USB-C (MCP2200):
* UART @ 115200 baud (Default), 921600 possible
* GPIO-s for bootstrap and reset
* LED-s:
* 2 per networking port (Green and Yellow)
* Green status LED
* Soft reset GPIO
* Power: 12V DC barrel jack
* External PoE:
* Option for PoE add-on
* Temperature Sensors:
* TMP1075 onboard
* CPU temperature
* Microchip MCP79402 RTC with battery back-up
* Microchip ATECC608C secure peripheral
* CPU heatsink with PWM fan
* Onboard header for case fan
Installation instructions:
1. Connect to UART via the USB-C port
2. Connect the management port
3. Boot and interrupt U-Boot
4. TFTP the OpenWrt initramfs image and boot it
5. SCP the OpenWrt eMMC GPT image to a running OpenWrt initramfs to /tmp
openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
And decompress it via:
gzip -d /tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
6. Wipe eMMC with:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
7. Flash OpenWrt eMMC image with:
dd if=/tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img
of=/dev/mmcblk0
After a restart OpenWrt will boot, and then regular sysupgrade can be used
for upgrades.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Microchip EV23X71A is a LAN9696 based EVB.
Specifications:
* CPU: Microchip LAN9696 switch SoC
* DRAM: 1GB DDR4
* Storage:
* 2MB QSPI NOR
* 4GB eMMC
* Networking:
* 24 x 10/100/1000 RJ45 via LAN8814 Quad PHY-s over QSGMII
* 4 x 100/1000/2500/5000/10000 SFP+ ports
* 1 x 10/100/1000 management RJ45 via LAN8840 PHY over RGMII (U-Boot too)
* USB: 1 x USB2.0 Type-A
* Management via USB-C (MCP2200):
* UART @ 115200 baud
* GPIO-s for bootstrap, reset and clock selection
* DIP switch for boostrap configuration
* LED-s:
* 2 per networking port (Green and Yellow)
* Green status LED
* Yellow reset LED
* Hard reset button
* Power:
* 12V DC barrel jack
* 48/56V DC screw terminal
* Selectable via toggle switch
* PTP support:
* Sync-E DPLL ZL30732B to generate the board required clocks
* Two SMAs for PTP and two for Station clock inputs and outputs
* Two ITU-T G.8275-compliant RS-422 interfaces for PTP applications
* External PoE:
* Option for PoE add-on, like EV14Y36A (IEEE 802.3af/at/bt Type 4
standard com-pliant)
* Option for external CPU control via SPI and PCIe
Installation instructions:
1. Connect to UART via the USB-C port
2. Connect the management port
3. Boot and interrupt U-Boot
4. TFTP the OpenWrt initramfs image and boot it
5. SCP the OpenWrt eMMC GPT image to a running OpenWrt initramfs to /tmp
openwrt-microchipsw-lan969x-microchip_ev23x71a-squashfs-emmc-gpt.img.gz
And decompress it via:
gzip -d /tmp/openwrt-microchipsw-lan969x-microchip_ev23x71a-squashfs-emmc-gpt.img.gz
6. Wipe eMMC with:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
7. Flash OpenWrt eMMC image with:
dd if=/tmp/openwrt-microchipsw-lan969x-microchip_ev23x71a-squashfs-emmc-gpt.img
of=/dev/mmcblk0
After a restart OpenWrt will boot, and then regular sysupgrade can be used
for upgrades.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add a new microchipsw target aimed add supporting Microchip switch
SoC-s.
Start by supporting LAN969x SoC-s as the first subtarget.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
