This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000h-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000h-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000h-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000e-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000e-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000e-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000s-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000s-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000s-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
1. Log in to the device and backup all the partitions,
especially unique "Factory" and "bdata" partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
3. Write new OpenWrt (U-Boot Layout) "BL2" and "FIP":
mtd -e BL2 write openwrt-mediatek-filogic-cudy_wr3000p-v1-ubootmod-preloader.bin BL2
mtd -e FIP write openwrt-mediatek-filogic-cudy_wr3000p-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC: "192.168.1.254", gateway "192.168.1.1"
5. Serve openwrt-mediatek-filogic-cudy_wr3000p-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean "/dev/mtd5" ubi partition to utilize maximum of free space:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Perform sysupgrade.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since there are some similar devices from Cudy (only WR3000P now)
this will allow to create OpenWrt U-Boot layout for all of them
using same DDR4 target.
Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21943
Signed-off-by: Robert Marko <robimarko@gmail.com>
Doesn't make sense to have he_twt_required enabled without
he_twt_respodner.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22577
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In hostapd conf this option is set to 1 by default.
Then it's set to 0 if the HE MAC capability bit is not present.
Add an option in wifi-scripts to manually control it.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22577
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
a665659dee50 wifi: mt76: fix beacon monitor for MBSSID nontransmitted BSS
1b26f5f63d42 wifi: mt76: mt7996: Decrement sta counter removing the link in mt7996_mac_reset_sta_iter()
0c1dedac48c3 wifi: mt76: mt7996: Switch deflink to seclink only if link lookup does not fail
7fa21be01b97 wifi: mt76: mt7996: Rely on msta_link link_id in mt7996_vif_link_remove()
492a407111c3 wifi: mt76: mt7996: Account active links in valid_links fields
ade83e44eda0 wifi: mt76: mt7996: Move mlink deallocation in mt7996_vif_link_remove()
efebeea5c058 wifi: mt76: mt7996: Destroy vif active links in mt7996_remove_interface()
a4c790aef40d wifi: mt76: mt7996: Add mcu APIs to enable/disable vif links.
018f60316d4d wifi: mt76: mt7996: Destroy active sta links in mt7996_mac_sta_remove()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Modern gawk rejects C-style /* ... */ comments in AWK code, treating
them as regex patterns where '*' has nothing to quantify. Replace all
such comments with AWK-style '#' comments in lantiq_bdi_conf.awk and
lantiq_ram_init_uart.awk.
Also replace the pattern 'if (x) /* comment */ else action' which used
a C comment as a null statement with the equivalent 'if (!x) action'.
Fixes build error:
awk: error: ? * + or {interval} not preceded by valid subpattern
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Link: https://github.com/openwrt/openwrt/pull/22458
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The VF2 boards store their ubootenv on /dev/mtd1 which is a SPI flash
partition. Add support for reading this partition in uboot-envtools,
and add the package into the VF2 image.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add uboot-envtools support for JDCloud RE-CS-02 RE-CS-07 and RE-SS-01
Signed-off-by: Fire Chen <firedevel@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/21787
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
NN6000v1 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: K4B4G1646E-BCMA 512MiB x2 = 1 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (2x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
NN6000v2 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: MT41K512M16VRN-107 IT:P 1GiB x2 = 2 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (4x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
Install via UART:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Install via Uboot WebUI:
- Only work when you flash a custom uboot with webui
- Push the reset button for 5 seconds, then use broswer to
access http://192.168.1.1/, then upload factory.bin.
Signed-off-by: Fire Chen <firedevel@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/21787
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add missing wpabuf_free calls to the hostapd_rrm_nr_set and
hostapd_rrm_beacon_req functions.
Signed-off-by: Vladimir Palevich <palevichva@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22538
Signed-off-by: Nick Hainke <vincent@systemli.org>
The hostapd configuration for SU-BEAMFORMEE was incorrectly using the
beamformer antenna count instead of the beamformee antenna count for the
[BF-ANTENNA-N] capability string.
Fix this by using config.beamformee_antennas instead.
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22511
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
"qca,gpio-mask" used to be read between ath9k_hw_init() and
ath9k_init_queues(). After 12913c3c56
it is read in ath9k_of_init(), but it gets overwritten by
ath9k_gpio_cap_init() during the call of ath9k_hw_init(), and causes
https://github.com/openwrt/openwrt/issues/22340
If keeping the most of 12913c3c56,
ath9k_gpio_cap_init() could be patched to keep the existing non-zero
gpio mask (coming from device tree).
Tested on Netgear WNDR4500 v3:
[ 22.558083] ath9k 0000:00:00.0: enabling device (0000 -> 0002)
[ 22.569548] ath: phy1: Use overridden gpio mask 0xf6ff
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/22376
Signed-off-by: Robert Marko <robimarko@gmail.com>
If the user removes all /lib/apk/packages/*.conffiles* files to prevent
sysupgrade from preserving configuration, the glob no longer matches and
sysupgrade ends up calling cat on a non-existent path:
cat: can't open '/lib/apk/packages/*.conffiles_static': No such file or directory
Fix this by using find cmd.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/22071
Signed-off-by: Robert Marko <robimarko@gmail.com>
No longer used. If swapping is desired, ralink,mtd-eeprom can be used.
Otherwise nvmem.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22207
Signed-off-by: Robert Marko <robimarko@gmail.com>
parent_tsf in struct rrm_measurement_beacon_report is le32 (32-bit),
but was being added with blobmsg_add_u16, truncating the value.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The beacon measurement token was not included in the ubus beacon-report
notification, causing consumers that need the token (e.g. for constructing
Beacon Metrics Response TLVs) to receive null.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use blobmsg_add_u32 for non-bool fields in order to avoid wrong
interpretations of the data on JSON/ucode conversion.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Reporting Detail value is a 1-byte field, but was written as le16,
producing a 2-byte write that also contradicts the length field of 1
in the subelement header.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reporting detail subelement (up to 3 bytes) was not accounted for
in the wpabuf allocation, causing a crash when reporting_detail is set
to a valid value (0, 1, or 2).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
After 02e2065203, it can happen that both,
[VHT160-80PLUS80] and [VHT160] are added to the vht_capab option in
an AP's hostapd.conf, which would cause a failure to start the AP.
Fix the logic in order to prevent such misconfiguration.
Fixes: #22481
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22482
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Nokia Valyrian device that implement similar spec of an
Airoha AN7581 RFB board.
Link: https://github.com/openwrt/openwrt/pull/21761
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use linux-firmware repository for IPQ5018, IPQ8074 and QCN9074.
All officially released firmware versions are available there.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21833
Signed-off-by: Robert Marko <robimarko@gmail.com>
mt76 tracks the PSM state of a sta internally with a wcid flag. TX to
such clients is skipped based on the presence of this flag.
This flag was not added to the PS state notify handler for MT7915 chips.
Without this flag, mt76 queues pending frames to the hardware,
accounting for airtime when a PSM notification is received while in a TX
iteration.
Set the PS flag for the STA WCID to prevent this from happening. TX gets
skipped in presence of this flag.
Link: https://patchwork.kernel.org/project/linux-wireless/patch/20260313112502.2026974-1-mail@david-bauer.net/
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a help text for the new --force-reinstall option, so that users
will actually find the new option.
(Also refresh patches)
Improves: 91cff1a "apk: add --force-reinstall option"
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/22426
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove unmatched endif.
fixes: 2948dbebbf ("mac80211: use OpenWrt mirror for b43 fw downloads")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22430
Signed-off-by: Robert Marko <robimarko@gmail.com>
% git shortlog v1.0.20250521..v1.0.20260223
Doug Freed (1):
wg-quick@.service: add deps on wg-quick.target
Jason A. Donenfeld (8):
wg-quick: linux: use smallest mtu, not largest
syncconf: account for psks removed from config file
wg-quick: linux: deal with resolvconf migration more gracefully
wg-quick: use addconf instead of setconf
wg-quick: linux: do not unnecessarily set sysctl
config: preserve const correctness
syncconf: account for persistent keepalive removed from config file
version: bump
Robyn Kosching (1):
wg-quick: pass on # comments to {Pre,Post}{Up,Down}
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22190
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Release Notes:
https://github.com/madler/zlib/blob/v1.3.2/ChangeLog
We also switch package tarball source to GitHub repository releases
to avoid package hash mismatch after the zstd upgrade.
The 005-* patch was suppressed by the upstream commit 15ba5055a935
("CMake: Adapt pkgconfig-file to the GnuInstallDirs layout.")
This patch also adjust the zlib.pc file path as it was changed in
the latest release.
The mipsel_24kc 'zlib' package size will increase by about 1 kB.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21228
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is no point in printing the missing M3 memory dump adress message
on each boot under the warning level, as not all boards need it at all.
So, degrate it to a debug print with QMI mask.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Originally, the .compatible string for EAP623-Outdoor HD tried to
shorten the "-outdoor" to "od". However, this naming was inconsistent
with the existing "eap610-outdoor". As "od" is not a common shorthand,
spell out the complete word: "eap623-outdoor-hd-v1".
Fixes: 5dbf93c8c5 ("ipq60xx: add support for TP-Link EAP623-Outdoor HD v1")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18804
Signed-off-by: Robert Marko <robimarko@gmail.com>
* e3f6a41 main: exit 1 when showing the usage
* b17c31f main: exit 1 on getopt() errors
* e086664 lexer: fix a minor memleak in jp_get_token()/match_token()
* e5a07f4 main: defer processing until options are processed
* afe72ad main: usage spell fixes
Signed-off-by: Paul Spooren <mail@aparcar.org>
