Specification:
The device is similar to the M30 but has only one LAN port and no WAN port.
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 2 buttons (WPS, reset, LED)
- 1 1Gbit LAN port
Disassembly:
- There are two screws at the power connector which must be removed. Afterwards the top case can be removed (it is clipped on, so some tools are required).
Serial Interface:
- The serial interface can be connected to the 4 pin holes on the board. Do NOT connect VCC.
- The pins are labelled on the PCB (RX, TX, GND)
- Settings: 115200, 8N1
MAC addresses:
- LAN MAC is stored in partition "Odm" at offset 0x8f
- WLAN MAC (2.4 GHz and 5GHz) is LAN MAC + 1
Reverting back to OEM firmware:
- There is currently no easy way to revert back to the OEM image
- The methods from M30 and M60 doesn't seem to work anymore
- If you plan to revert back to OEM firmware later, do the following steps before flashing OpenWrt:
- Boot from initramfs as described in "Flashing via U-Boot" but don't flash anything
- Instead, make a backup of UBI and UBI1 partition
- The created dumps must be written to the initial partitions to revert back to OEM
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.50/ (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-recovery.bin
- Note: The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If flashing was successful, OpenWrt is accessible via 192.168.1.1
- The recovery image boots an initramfs image, flash the sys upgrade image to get to „normal“ OpenWrt mode
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-initramfs-kernel.bin
- Supply the board with 12V
- Select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22776
(cherry picked from commit 145bc7e52f)
Link: https://github.com/openwrt/openwrt/pull/22958
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The TARGET_CPPFLAGS contain the include paths used by OpenWrt. This also
contains the including of the fortify sources headers. If they are not
provided, the applications will not use fortify sources headers when
compiled against musl. Add them to cmake builds too. cmake does not
support a special CPPFLGS option [0], just add them to CFLAGS and
CXXFLAGS like we also do it for meson and normal make.
This should fix fortify sources support for cmake builds.
I found this explanation for the flags:
* CFLAGS: C flags, passed during compile AND link
* CXXFLAGS: C++ flags, passed during compile AND link
* CPPFLAGS: pre-processor flags, passed ONLY during compile
* LDFLAGS: linker flags, passed ONLY during link
[0]: https://gitlab.kitware.com/cmake/cmake/-/issues/12928
Link: https://github.com/openwrt/openwrt/pull/22042
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7bf8d568f6)
Currently, for targets that use the CONFIG_TARGET_ROOTFS_TARGZ a single
rootfs tarball is generated for the subtarget based of $(TARGET_DIR).
However, this means that it does not respect DEVICE_PACKAGES like other
rootfs images.
So, lets augment CONFIG_TARGET_ROOTFS_TARGZ by adding a proper targz fstype
so that per device rootfs is generated under lock.
This is required so that devices that use custom sysupgrade archives like
Methode devices, can actually include a per device rootfs so when building
for multiple devices and with CONFIG_TARGET_PER_DEVICE_ROOTFS set the built
image actually includes the listed DEVICE_PACKAGES.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit d89cb72c23)
If a package has an ABI version defined, set priority to 10. The enables
packages with an ABI version to be installed by their base name instead
of a name and an ABI version, e.g.:
libfoo3, where 3 is the ABI version can be installed by just libfoo.
This affects manual installation only, as the dependency resolution
takes care of ABI versions.
Refactor apk priority logic into a helper define.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21369
(cherry picked from commit 470e030a5e)
Link: https://github.com/openwrt/openwrt/pull/21547
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to the way apk lifecycle scripts are defined, they might end up with
multiple shebangs. Remove them.
Before:
post-upgrade: |
#!/bin/sh
export PKG_UPGRADE=1
#!/bin/sh
[ "${IPKG_NO_SCRIPT}" = "1" ] && exit 0
[ -s ${IPKG_INSTROOT}/lib/functions.sh ] || exit 0
. ${IPKG_INSTROOT}/lib/functions.sh
export root="${IPKG_INSTROOT}"
export pkgname="adblock-fast"
add_group_and_user
default_postinst
#!/bin/sh
# check if we are on real system
if [ -z "${IPKG_INSTROOT}" ]; then
/etc/init.d/adblock-fast enable
fi
exit 0
After:
post-upgrade: |
#!/bin/sh
export PKG_UPGRADE=1
[ "${IPKG_NO_SCRIPT}" = "1" ] && exit 0
[ -s ${IPKG_INSTROOT}/lib/functions.sh ] || exit 0
. ${IPKG_INSTROOT}/lib/functions.sh
export root="${IPKG_INSTROOT}"
export pkgname="adblock-fast"
add_group_and_user
default_postinst
# check if we are on real system
if [ -z "${IPKG_INSTROOT}" ]; then
/etc/init.d/adblock-fast enable
fi
exit 0
Fixes: b52e897 ("include/package-pack: remove leading whitespace from install scripts")
Fixes: 03880e2 ("include/package-pack: add missing apk package lifecycle events")
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21369
(cherry picked from commit 1dec4683f6)
Link: https://github.com/openwrt/openwrt/pull/21547
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix setting implicit self-provides for packages when they don't have any
PROVIDES specified.
Remove redundant self-provide for kmods, since kmods are packages and
will have a self-provide added already.
Fixes: 5ed650a ("build: add support for virtual provides")
Fixes: 9b37b71 ("build: provide virtual self in kmods")
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21369
(cherry picked from commit 2d844a0770)
Link: https://github.com/openwrt/openwrt/pull/21547
Signed-off-by: Robert Marko <robimarko@gmail.com>
Same as for the base package name, when a package has an ABI version,
provide both unversioned provider in addition to one with ABI version
and version.
So for each provide instead of providing only:
$provide$ABI_version=$package_version
now provide:
$provide $provide$ABI_version=$package_version
When a provide ends in a number, the ABI version will be prefixed with
a - sign, e.g.: provide1-0
Fixes: 18029977 ("build: fix apk packaging and ABI-versioning")
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21369
(cherry picked from commit 952c918028)
Link: https://github.com/openwrt/openwrt/pull/21547
Signed-off-by: Robert Marko <robimarko@gmail.com>
Don't mark all provides as virtual when ALTERNATIVES is set.
Automatically marking all provides as virtual prevents variants from
conflicting between each other. Alternatives have nothing to do with
packaging and packages are expected to manage their own provides.
Updated internal provides explanation.
Remove unnecessary back slashes from FormatProvides.
Fixes: 18029977 ("build: fix apk packaging and ABI-versioning")
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21369
(cherry picked from commit 2a1977a4b8)
Link: https://github.com/openwrt/openwrt/pull/21547
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove default provider priority since packages are expected to
explicitly declare virtual provides and set default variants. With
default priority some package variants without PROVIDES and not marked
as default end up with priority 0 and are not picked for installation.
Before the change dnsmasq-dhcpv6 is selected for dnsmasq, because the
former has higher priority:
name <dnsmasq> selected from selectable list
select_package: dnsmasq (requirers=1, autosel=1, iif=0, order_id=0x4000005f)
consider dnsmasq-2.91-r2 iif_triggered=0, tag_ok=1, selectable=1, available=1, flags=0x0, provider_priority=0, installed=0
prefer existing package
choose as new provider
consider dnsmasq-dhcpv6-2.91-r2 iif_triggered=0, tag_ok=1, selectable=1, available=1, flags=0x0, provider_priority=1, installed=0
prefer highest declared provider priority
choose as new provider
consider dnsmasq-full-2.91-r2 iif_triggered=0, tag_ok=1, selectable=1, available=1, flags=0x0, provider_priority=1, installed=0
prefer lowest available repository
selecting: dnsmasq-dhcpv6-2.91-r2, available: 1
assign dnsmasq-dhcpv6 to dnsmasq-dhcpv6-2.91-r2
assign dnsmasq to dnsmasq-dhcpv6-2.91-r2
disqualify_package: dnsmasq-2.91-r2 (conflicting provides)
disqualify_package: dnsmasq-full-2.91-r2 (conflicting provides)
apply_constraint: libc
apply_constraint: provider: libc-1.2.5-r5: 1
After the change dnsmasq is selected for dnsmasq based on
lexicographical order:
name <dnsmasq> selected from selectable list
select_package: dnsmasq (requirers=1, autosel=1, iif=0, order_id=0x4000005f)
consider dnsmasq-2.91-r2 iif_triggered=0, tag_ok=1, selectable=1, available=1, flags=0x0, provider_priority=0, installed=0
prefer existing package
choose as new provider
consider dnsmasq-dhcpv6-2.91-r2 iif_triggered=0, tag_ok=1, selectable=1, available=1, flags=0x0, provider_priority=0, installed=0
prefer lowest available repository
consider dnsmasq-full-2.91-r2 iif_triggered=0, tag_ok=1, selectable=1, available=1, flags=0x0, provider_priority=0, installed=0
prefer lowest available repository
selecting: dnsmasq-2.91-r2, available: 1
assign dnsmasq to dnsmasq-2.91-r2
disqualify_package: dnsmasq-dhcpv6-2.91-r2 (conflicting provides)
disqualify_package: dnsmasq-full-2.91-r2 (conflicting provides)
apply_constraint: libc
apply_constraint: provider: libc-1.2.5-r5: 1
Fixes: dea8397 ("include/package-pack: add default 'provider_priority' for APK packages")
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21369
(cherry picked from commit 49fc319033)
Link: https://github.com/openwrt/openwrt/pull/21547
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add an implicit self-provide to kmods. apk can't handle self provides,
be it versioned or virtual, so opt for a prefix and a suffix instead.
Package name without a prefix/suffix is too generic and might conflict
with other packages, e.g. wireguard. This allows several variants to
provide the same virtual package without adding extra provides to the
default one, e.g. r8169 implicitly provides kmod-r8169-any and is marked
as default, so r8125 can explicitly provide @kmod-r8169-any as well.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
(cherry picked from commit 9b37b7185c)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow defining virtual provides using the PROVIDES field by prefixing
them with @, e.g.:
PROVIDES:=@ca-certs
Virtual provides don't own the provided name and multiple packages with
the same virtual provides can be installed side-by-side. Packages must
still take care not to override each other's files.
Add an implicit self-provide to packages. apk can't handle self
provides, be it versioned or virtual, so opt for a suffix instead. This
allows several variants to provide the same virtual package without
adding extra provides to the default one, e.g. wget implicitly provides
wget-any and is marked as default, so wget-ssl can explicitly provide
@wget-any as well.
Filter out virtual provides when generating metadata.
Filter out virtual provides prefix and self provide where appropriate.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
(cherry picked from commit 5ed650acbf)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refactor provides logic into a helper define and use it for both apk and
control. Document the behavior.
Store preformatted provides in Package/$(1)/PROVIDES similar to defines.
Remove unnecessary logging.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
(cherry picked from commit cefbf1184f)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
The updated logic for the APK dependencies and provides is as follows:
- If ABI version is defined:
- package is named `package_name-ABI_version`
- package implicitly provides
`package_name-ABI_version=package_version`
this implies that only one version of a package per ABI can be
installed at the same time
- additionally provide `package_name` so multiple packages can be
looked up by its base name
- for each `provides`, provide `provide-ABI_version=package_version`
this implies that only one version of a provide can be installed at
the same time
- else if ABI version is _not_ defined
- package is named `package_name`
- package implicitly provides `package_name=package_version`
this implies that only one version of a package can be installed at
the same time
- if `alternatives` is defined
- for each `provides`, provide `provide`
this implies that multiple versions of a provide can be installed
at the same time
- else if `alternatives` is _not_ defined
- for each `provides`, provide `provide=package_version`
this implies that only one version of a provide can be installed
at the same time
Both cases a package can be looked up by its base name.
ABI version `alternatives`, `conffiles`, `conffiles_static`, `list` and
`rusers` files so multiple versions of the same ABI package can be
installed side by side, and so they don't overwrite each other's
packaging files.
ABI version `EXTRA_DEPENDS` so dependencies can be correctly looked up
using the existing OpenWrt semantics without the ABI specified. This is
needed since ABI-versioned libraries no longer provide
`package_name=package_version`, so that they can be installed side by
side.
Remove duplicate dependencies when `EXTRA_DEPENDS` specifies a versioned
one that is already in `DEPENDS`.
ABI is defined
------------------------------------------------------------------------
`libsqlite3` has `PROVIDES` set to `libfake` and has two different ABI
versions installed. `libfake` is just an example to demonstrate the
mechanics, as the library can already be depended upon using e.g.
`libsqlite3-0=3.51.0-r1`. Note the ABI-versioned lists.
```
root@OpenWrt:/tmp# apk add --allow-untrusted ./libsqlite3-0-3.51.0-r1.apk
(1/1) Installing libsqlite3-0 (3.51.0-r1)
libsqlite3-0-3.51.0-r1.post-install: Executing script...
OK: 22 MiB in 157 packages
root@OpenWrt:/tmp# apk add --allow-untrusted ./libsqlite3-1-4.00.0-r1.apk
(1/1) Installing libsqlite3-1 (4.00.0-r1)
libsqlite3-1-4.00.0-r1.post-install: Executing script...
OK: 23 MiB in 158 packages
root@OpenWrt:/tmp# apk query --fields name,version,contents,provides libsqlite3-0 libsqlite3-1
Name: libsqlite3-0
Version: 3.51.0-r2
Provides: libfake-0=3.51.0-r2 libsqlite3
Contents:
lib/apk/packages/libsqlite3-0.list
usr/lib/libsqlite3.so.0
usr/lib/libsqlite3.so.3.51.0
Name: libsqlite3-1
Version: 4.00.0-r1
Provides: libfake-1=4.00.0-r1 libsqlite3
Contents:
lib/apk/packages/libsqlite3-1.list
usr/lib/libsqlite3.so.1
usr/lib/libsqlite3.so.4.00.0
root@OpenWrt:/tmp# ls -lh /usr/lib/libsqlite3.so.*
lrwxrwxrwx 1 root root 20 Nov 20 00:23 /usr/lib/libsqlite3.so.0 -> libsqlite3.so.3.51.0
lrwxrwxrwx 1 root root 20 Nov 20 00:27 /usr/lib/libsqlite3.so.1 -> libsqlite3.so.4.00.0
-rwxr-xr-x 1 root root 1.0M Nov 6 18:19 /usr/lib/libsqlite3.so.3.51.0
-rwxr-xr-x 1 root root 1.0M Nov 6 18:19 /usr/lib/libsqlite3.so.4.00.0
```
ABI is not defined
------------------------------------------------------------------------
Both `avahi-dbus-daemon` and `avahi-nodbus-daemon` provide `avahi-daemon`,
but have no ABI specified. This results in `avahi-daemon=0.8-r11` provides
for both packages and only one being able to be installed at the same time:
```
root@OpenWrt:/tmp# apk add --allow-untrusted ./avahi-nodbus-daemon-0.8-r11.apk
(1/4) Installing libavahi-nodbus-support (0.8-r10)
libavahi-nodbus-support-0.8-r10.post-install: Executing script...
(2/4) Installing libdaemon (0.14-r5)
libdaemon-0.14-r5.post-install: Executing script...
(3/4) Installing libexpat (2.7.3-r1)
libexpat-2.7.3-r1.post-install: Executing script...
(4/4) Installing avahi-nodbus-daemon (0.8-r11)
avahi-nodbus-daemon-0.8-r11.post-install: Executing script...
23 MiB in 160 packages
root@OpenWrt:/tmp# apk query --fields provides avahi-nodbus-daemon
Provides: avahi-daemon=0.8-r11
root@OpenWrt:/tmp# apk add --allow-untrusted ./avahi-dbus-daemon-0.8-r11.apk
ERROR: unable to select packages:
avahi-dbus-daemon-0.8-r11:
conflicts: avahi-nodbus-daemon-0.8-r11[avahi-daemon=0.8-r11]
satisfies: world[avahi-dbus-daemon><Q1R111s+ke9Vf+eCxDHX2BZVUK54Q=]
avahi-nodbus-daemon-0.8-r11:
conflicts: avahi-dbus-daemon-0.8-r11[avahi-daemon=0.8-r11]
satisfies: world[avahi-nodbus-daemon><Q1BAu7nLI2MgRabpveLTGO2ksQz7E=]
```
Provides and alternatives
------------------------------------------------------------------------
Both `uclient-fetch` and `wget-nossl` provide `wget` and specify
alternatives, so provides are not versioned and both packages can be
installed at the same time:
```
root@OpenWrt:/tmp# apk query --fields name,version,contents,provides uclient-fetch wget-nossl
Name: uclient-fetch
Version: 2025.10.03~dc909ca7-r1
Provides: wget
Contents:
bin/uclient-fetch
lib/apk/packages/uclient-fetch.alternatives
lib/apk/packages/uclient-fetch.list
Name: wget-nossl
Version: 1.25.0-r1
Provides: gnu-wget wget
Contents:
lib/apk/packages/wget-nossl.alternatives
lib/apk/packages/wget-nossl.list
usr/libexec/wget-nossl
```
Fixes: https://github.com/openwrt/openwrt/issues/20582
Fixes: https://github.com/openwrt/openwrt/issues/20802
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/20819
(cherry picked from commit 18029977f6)
Link: https://github.com/openwrt/openwrt/pull/21253
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows an optional tag to be put in the .config file which is
included in the filename of the resulting images, so it's easier to
build images with different functionality for the same target hardware.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Link: https://github.com/openwrt/openwrt/pull/20984
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 24b8db118b)
Downloading packages from git requires zstd to compress their tarballs.
Make sure that zstd from host tools is compiled when running make
download. Otherwise, either the download would fail because zstd is not
present or a random version from the host would be used leading to hash
mismatches.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/21125
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move .quilt_used from kernel-defaults.mk to quilt.mk.
This is done to be consistent with the parallel Build/Patch/Default and
Host/Patch/Default and permit better Quilt handling on any package that
might use Kernel/Patch/Default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 61bfcc4bd7.
The change was wrong as it was placed on the wrong define section.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move .quilt_used from kernel-defaults.mk to quilt.mk.
This is done to be consistent with the parallel Build/Patch/Default and
Host/Patch/Default and permit better Quilt handling on any package that
might use Kernel/Patch/Default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware
--------
SOC: MediaTek MT7981
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND
WIFI: Mediatek MT7915 (integrated) 2x2 802.11ax 2.4 / 5 GHz
ETH: Mediatek MT7981 internal 1 GbE PHY
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the EAX17. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Jascha Sundaresan <flizarthanon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20354
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add gcc config option for fanalyzer. As a result of this option, a static
analysis of the program flow is conducted, allowing interprocedural paths
to be identified and warnings to be issued if problems are identified.
Link: https://github.com/openwrt/openwrt/pull/12576
Signed-off-by: Nick Hainke <vincent@systemli.org>
In implementing APK support it seems a a leftover was never removed that
creates an unused tmp directory in the package feed directory.
Drop it as it's not used anywhere. What is actually needed is the
creation of the $$(PDIR_$(1)) directory for the feed package directory
in the bin/packages directory.
This was a side effect of using INSTALL_DIR on $$(PDIR_$(1))/tmp that
indirectly creates the $$(PDIR_$(1)) parent directory.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit cea8507dcc.
This actually cause package pack error on every package outside the
target directory.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In implementing APK support it seems a a leftover was never removed that
creates an unused tmp directory in the package feed directory.
Drop it as it's not used anywhere.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
APK will generate the compressed scripts.tar by default, however we rely
on using TAR support for updating the tarball on the fly and this does not
work when tarball is compressed and will cause the following errors:
staging_dir/host/bin/tar: Cannot update compressed archives
Try /staging_dir/host/bin/tar --help' or
staging_dir/host/bin/tar --usage' for more information.
So, lets simply decompress the scripts.tar.gz before usage and then
compress it after we are done.
Fixes: 5d85657f6d ("apk-tools: implement compression of on-device scripts.tar")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds the -Wl,-z,pack-relative-relocs linking options.
This reduces the size of some binaries.
This is only supported on i386, x86_64, aarch64 and loongarch64 in
binutils. This feature is not support for MIPS.
musl libc supports it since version 1.2.4 .
glibc supports it since vesion 2.36.
binutils ld supports it since version 2.38 for x86 and since version
2.43 for LoongArch.
This reduces the size of the armsr default root file system from
5,262,198 bytes to 5,200,950 bytes by 61,248 bytes.
Link: https://github.com/openwrt/openwrt/pull/20679
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
