Patch 87cb0446b7 also applies to higher kernel versions.
To apply to them it has been moved to a separate file in pending.
Fixes: 87cb0446b7 ("generic: fix broken TCP fraglist GRO patch")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18511
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream version of ARM gc sections skip eeping some section. It was
reported some kernel load hang hence restore what we original did and
introduce a new patch that add the additional entry on top of the
upstream version.
Fixes: #18500
Fixes: 7843f21c51 ("generic: replace ARM gc sections patch with upstream version")
Tested-by: Stefan Kalscheuer <stefan@stklcode.de> (Turris Omnia)
Link: https://github.com/openwrt/openwrt/pull/18503
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move all patch that got merged upstream from pending to backport and add
related tag. This is to make it easier to update to kernel 6.12.
Patch 680 required some special care as the upstream version had to be
split in a series of 6 patch.
Referesh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.
To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.
Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79c ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Patches 751-03 and 751-04 as a result of commit 6407ef8d2b
were incorrectly placed in the backport folder.
So they return to their proper place.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In case a broken fit image is present on flash the fitblk driver would
not map any /dev/fit* devices, but also not always close the block device
the image resides on. In case of ubiblock devices this is fatal as one
then cannot remove the ubiblock device (-EBUSY), and hence cannot replace
the broken image.
Always close the block device in case no sub-image was mapped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to API changes during the backport, the default value of Tx LPI
timer is accidentally left unset, breaking the network if EEE is on.
Set the default timer to 1ms on init, and fix an incorrect condition.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Prior to commit 8a7d12d674,
cdc-ethernet USB LTE modems (e.g. Quectel EC200A) were consistently named
usb0. After 8a7d12d67, devices began renaming to eth1 due to an assumption
that local MAC addresses originate exclusively from the kernel. Some
devices provide driver-assigned local MACs, causing point-to-point
interfaces with driver-set MACs to adopt eth%d names instead of usb%d.
Restore the naming exception for point-to-point devices: interfaces
without driver MACs or with driver-provided local MACs will retain the
usb%d convention. This addresses issues reported in [1] and fixed in [2].
[1] https://lore.kernel.org/all/Z00udyMgW6XnAw6h@atmark-techno.com/
[2] https://lore.kernel.org/all/20241203130457.904325-1-asmadeus@codewreck.org/
Tested-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17757
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport Mediatek SoC EEE support from net-next upstream.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[refreshed patches]
Add validation and support for parsing of name/value pairs with CRLF line
endings.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17935
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix broken NVMEM ASCII patch for x86 target as it does currently fail
compilation when OF is not compiled.
Also mute a warning for integer from pointer without a cast.
Fixes: 73a6cb983c ("generic: add pending support for NVMEM ASCII ENV layout driver")
Link: https://github.com/openwrt/openwrt/pull/17845
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch to support NVMEM ASCII ENV layout driver. This is a
generic driver to handle simple NVMEM partition that store environment
in a simple text format. This is the case for Linksys devinfo partition
that are litterally txt file with format "name=value\n"
Such driver works similar to u-boot,env with a similar format. While at
it also introduce a patch to generalize mac-base handling for also other
layout driver.
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
RTL8221B-VB-CG 2.5Gbps PHY (C45) mdio-bus:01: rtl822xb_config_init failed: -110
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch "net: phy: realtek: mark existing MMDs as present"
When using Clause-45 mode to access RealTek RTL8221B 2.5G PHYs some
versions of the PHY fail to report the MMDs present on the PHY.
Mark MMDs PMAPMD, PCS and AN which are always existing according to
the datasheet as present to fix that.
Fixes: #16823, #17183, #17232
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Expose the temperature sensor built-into RTL822x 2.5G and 5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
1. Import pending patch to fix ramips/mt7621 64MB targets.
2. Do not enable CONFIG_PAGE_POOL_STATS by default.
Signed-off-by: Danila Romanov <pervokur@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As per @KanjiMonster comment: st1202_dt_init() calls devm_led_classdev_register_ext() before the internal data structures are properly setup, so the leds become visible to user space while being partially initialized, leading to a window where trying to access them causes a NULL pointer access.
Move devm_led_classdev_register_ext() to the last thing to happen during initialization.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17543
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch is also needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11 which is included here.
The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns
If the led node is present in the controller then the channel is
set to active.
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
