It seems new kernel version introduced -Wmissing-prototypes. This new
warning reported drivers that define non static function that are used
statically in the driver.
Fix this by declaring making those function actually static if not
defined in any header and not used outside of the single driver.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It seems new kernel linux version reorganized the header include and now
of.h needs to be explicitly included. This should have been done from
when the driver was introduced.
Add the missing of.h header to fix compilation error in later kernel
version.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The reason phy fails to probe without explicitly overrided phy id is
that the reset timing fails to match. Fix it with proper `reset-delay-us` and
`reset-post-delay-us`.
While at it, change LED settings to match EAP610-Outdoor.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18450
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
SoC: MediaTek MT7628AN
RAM: 128 MB, Zentel A3R1GE40JBF-8E
Flash: 16MB, Winbond W25Q128JV
Switch: rt3050-esw, 2 ports 100 Mbps
WiFi: MediaTek mt7628-wmac 2.4GHz 802.11n and MediaTek MT7663 5GHz
802.11ac (PCIe)
WWAN: Quectel EC200A-EL 4G modem (USB)
GPIO:
* 1 button (Reset/WPS)
* 6 LEDs (Power+WPS, LAN, 3xSignal)
* USB port power controls
* Modem reset
* Modem programming switch
* Internal/external antenna switch for 4G
Serial Interface:
TP10 - 3.3V can be used for level shifter, if needed
TP9 - TX
TP8 - RX
TP11 - GND
Interface properties: 115200, 8N1
Access to console using serial port for OEM firmware:
Username: admin
Password: 1234
Flashing via TFTP (no disassembling or soldering required):
1. Connect your PC and router to port LAN
2. Configure PC interface using static IP 192.168.1.225, mask
255.255.255.0
3. Place OpenWRT firmware image (*-squashfs-tftp-recovery.bin) to TFTP
root folder and renamed it to tp_recovery.bin
4. Unplug power from router
5. Press and hold Reset/WPS button
6. Power up the router
7. Wait until TFTP started uploading image (~10 seconds after power up)
and release Reset/WPS button
8. Wait until image uploaded, i.e. until LAN LED start lighting
9. Enable DHCP address on PC interface and wait for assigning address
10. Use ssh (root@192.168.1.1) to configure router properties
Depends on patch for firmware-utils package:
https://github.com/openwrt/firmware-utils/commit/2051fe5b
Signed-off-by: Sergii Shcherbakov <shchers@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17819
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_QCOM_IPA kernel cofig was enabled by mistake and conflicts with
mac80211 as it indirectly selects QMI HELPERS. Backports project provid
his own version of QMI HELPERS hence it should not be built-in.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Make the RPM partition read-only. This was a mistake and a leftover from
staging branch but I can take this mistake as an excuse to document the
current problem with RPM.
It might happen that a board ship with a broken RPM .mbn, broken not in
the sense that the board doesn't boot or it's a brick but broken in the
sense that it's outdaed and suffer from a bug fixed in new version.
This bug consist in a problem with the regulators between USB and NSS.
The old RPM mess with the NSS regulator (l2) and change the voltage for
it while configuring the USB regulator (l5).
This cause the ethernet subsystem to malfunction with the port not
working.
To workaround this, it's needed to disable RPM handling and CPUFreq.
With these 2 disabled, the old RPM doesn't touch regulators and Ethernet
works correctly.
New RPM correctly handle regulators for USB (l5) and doesn't suffer from
this problem. A solution for this is getting discussed with QCOM hoping
to get some good feedback for it.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing NSSCC boot stall. These patch are needed to
prevent the ICC to disable critical clock for NSSCC NOC.
Without these the system will stall and reboot with watchdog.
While at it also remove an extra clock from DTSI as it currently have no
use. Original patch is not modified to keep consistency with series
proposed upstream.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant comment in NSSCC clock patch. The problem has been
identified hence the comment doesn't apply anymore.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Define default partition table for SPI-NAND mounted on reference board.
This is where is normally placed the rootfs UBI.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh dts SPI-NAND patch to to v14. This is to keep stuff synced with
current pending patch revision and make it easier to replace patch
later (and discover something broke in the meantime)
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh the NSSCC patch for new PCIe patches. To keep track of fuzz
changes for the IPQ95xx patches, patch are not refreshed currently.
For the specific case of NSSCC patch, quilt gets confused and apply the
patch in the wrong node, putting it in the RPM node (causing all kind of
funny errors at runtime)
Correctly fix the patch to put the node right after the PCIe nodes.
Also the PORT patch need to be refreshed as the gpio header is added by
the PCIe patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add PCIe upstream patch and related nodes to enable PCIe on IPQ95xx.
Minimal change were required to backport the patch and apply on current
kernel. Refresh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add USB3 kmods to the default package list, USB3 correctly works on
IPQ95xx hence it can be enabled.
While at it drop the NSS-DP as it was added by mistake as the ethrnet
platform is handled differently on this SoC with pending upstream
drivers.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.85..HEAD
(HEAD -> bba53a117a4a5c29da892962332ff1605990e17a)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This brings up a serial console on the USB device port of
the DNS-313 by:
- Activating the usbgadget feature
- Selecting the usbgadget-acm package
- Adding an inittab that opens a console at ttyGS0 which is
the device side of ttyACMn of a connected host
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-4-d84de8e86931@linaro.org/
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18399
Signed-off-by: Robert Marko <robimarko@gmail.com>
ath9k base starts at 512. This is a problem as it uses gpio_request_one
to request the GPIO, which is legacy API.
This upstream pending patch needs to also be ported to mac80211.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is only used by mach files, which are no longer used in OpenWrt.
Allows removing a custon ath9k_platform.h file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
PHY2 led1 is configured to control PHY1's LED. Change it to PHY2.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18361
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds support for setting bridge port learning and isolation flags on
ipq40xx.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch adds support for D-Link DGS-1210-26 rev. F1
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash (MX25L25635E)
* 24 x 10/100/1000BASE-T ports
* 2 x SFP ports
* Power LED
* Reset button on front panel
Installation using OEM webinterface
-----------------------------------
1. Make sure you are running OEM firmware from secondary slot. If not, switch to image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image squashfs-factory_image1.bin via Tools > Backup / Upgrade Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot from image1
4. Tools > reboot
Known working firmware version for this procedure: 6.20.007
Installation using TFTP and serial console
------------------------------------------
1. Prepare a TFTP server with the OpenWrt *initramfs-kernel.bin and assign it an IP from 10.90.90.0/24 (except 10.90.90.90)
2. Connect the TFTP server to one of switch's ports
3. Connect to the serial console (115200 baud) and power on the switch
4. Press the ESC key once you see "Hit Esc key to stop autoboot" in the console output
5. Press CTRL+C keys to get into the real U-Boot prompt
6. Init the network with the command "rtk network on"
7. Load the OpenWrt image with the command "tftpboot 0x8f000000 <TFTP_SERVER_IP>:<IMAGE_FILE>"
(<TFTP_SERVER_IP> is the TFTP server's IP, e.g. 10.90.90.100; <IMAGE_FILE> is the name of the image provided by the TFTP server)
8. Boot the OpenWrt image with the command "bootm"
9. Browse to https://192.168.1.1/cgi-bin/luci/admin/system/flash
10. Upload the the OpenWrt *squashfs-sysupgrade.bin to the switch
11. Wait for it to reboot
Signed-off-by: Christian Steiner <christian.steiner@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/18378
Signed-off-by: Sander Vanheule <sander@svanheule.net>
NEC Aterm WG2200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 4T4R (Qualcomm Atheros QCA9984)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 12x/4x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- Power : 12 VDC, 1.5 A (Max: 20 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image:
1. Connect and open serial console
2. Power on WG2200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Rplace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the Diodes PI4IOE5V9539LE I2C Expander chip.
(compatible with NXP PCA9539)
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI of all versions, and
initramfs-factory.bin image of OpenWrt has the larger block data for
initramfs image. So that image cannot be applied to the stock WebUI
at all.
MAC addresses:
LAN : 98:F1:99:xx:xx:7C (config, 0x6 (hex))
WAN : 98:F1:99:xx:xx:7D (config, 0xc (hex))
2.4 GHz: 98:F1:99:xx:xx:7E (config, 0x0 (hex))
5 GHz : 98:F1:99:xx:xx:7F (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add more DT labels and move a USB hub node to dts files of Aterm devices
as a preparation for adding support of Aterm WG2200HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
The built-in watchdog is redundant when the device has an external
GPIO based hardware watchdog. And there is a conflict that both of
them will attempt to register the same device entry in sysfs. This
resulted in the built-in watchdog being unable to be activated.
This patch explicitly disables the built-in watchdog for devices
that use GPIO watchdog to fix the error:
[ 1.779206] ath79-wdt 18060008.wdt: unable to register misc device, err=-16
[ 1.786355] ath79-wdt: probe of 18060008.wdt failed with error -16
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18395
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Convert the property variable type of "qcom,coexist-support" from
u32 to u8 to match the definition in the dt-bindings document.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, network ports using PHYs get a link, but there is no traffic.
Make it work again by moving the MAC config to phylink_mac_link_up.
A similiar change has been previously applied for RTL83xx in commit
cd958d945b ("realtek: 6.6: refactor mac config and link up for
RTL83xx").
Fixes: https://github.com/openwrt/openwrt/issues/17010
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18268
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The generic target configuration activates the
CONFIG_LEDS_CLASS_MULTICOLOR option. Do not deactivate it for the stm32
target.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This restores sysupgrade support
Since OpenWrt 23.05, the firmware selector no longer provides sysupgrade
images for RE450 V1 & V2 and RE355 v1 due to image size constraints
(~5.7MB limit), making the generic build unusable.
This commit moves RE450 V1 & V2 to the tiny target, enabling:
- Smaller image builds within the flash size limit.
- Restored sysupgrade support via the firmware selector.
- A secure-by-default wireless setup while allowing full management via UCI.
- Officially supported images, reducing the need for custom (potentially insecure) builds.
This ensures users can install a functional OpenWrt build without compromising security defaults.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
[Squashed the commits together and just copied the target definition
from the generic subtarget.]
Link: https://github.com/openwrt/openwrt/pull/18126
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, ESMT M14D128168A (2Y)
Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt,
SPI)
Switch: MediaTek MT7628AN, 3 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n
USB: 1 port USB 2.0
GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power,
Internet, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom near the LEDs hidden by rubber mounts.
After removing the screws, pry the gray plastic part around (it is secured
with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between LAN
ports and the WAN one.
Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC
interface using IP 192.168.1.2, mask 255.255.255.0
2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin)
renamed to KN-1221_recovery.bin via TFTP
3. Power up the router while pressing Wi-Fi button
4. Release Wi-Fi button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods
described above with the help of the appropriate firmware image found on
osvault.keenetic.net.
When using OEM bootloader, the firmware image size cannot exceed the size
of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/18164
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.
To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.
Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79c ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Only force compat_version to 1.2 if it was less than 1.2 before, as changes
1.1 and 1.2 were bootloader-related and a completed boot indicates that the
changes have been completed. Newer compat version 1.3 indicates a config change
and should not be forced on boot.
Fixes: 84fc59c0d5 ("mediatek: filogic: bpi-r3: set netdev-name for sfp1 port")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Patches 751-03 and 751-04 as a result of commit 6407ef8d2b
were incorrectly placed in the backport folder.
So they return to their proper place.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add 'ubootmod' variant for the ASUS ZenWiFi BT8.
An out-of-tree installer will be provided in Github to allow users an easy
transition from the stock loader to OpenWrt's bootchain which is built from
source.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Break out all flash-layout dependent parts from device tree into separate
dtsi file to be used by both, stock layout and upcoming ubootmod variant.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7988D SoC (3x Cortex-A73 @1.8 GHz max)
1GB DDR4 RAM
128MB SPI-NAND (Winbond)
MediaTek MT7996 BE14000 Tri-Band Wi-Fi 7
3x LAN (2x 1GE MT7988 built-in, 1x 2.5GE MaxLinear GPY211C)
1x WAN (2.5GE MT7988 built-in)
LED: RGB PWM (supported as 3x PWM LED)
USB: 1x USB 3
Buttons: RESET, WPS
UART: 115200 8N1 3.3V
Installation
------------
1. Hold down RESET button and power on the device until
LED pulses red.
2. Assign IP 192.168.1.70/24 to your computer's Ethernet port
3. Connect Ethernet to one of the 1GE LAN ports
4. Open browser and visit http://192.168.1.1
5. Upload openwrt-mediatek-filogic-asus_zenwifi-bt8-factory.bin
6. Once OpenWrt initramfs system comes up, do sysupgrade using
openwrt-mediatek-filogic-asus_zenwifi-bt8-squashfs-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In case a broken fit image is present on flash the fitblk driver would
not map any /dev/fit* devices, but also not always close the block device
the image resides on. In case of ubiblock devices this is fatal as one
then cannot remove the ubiblock device (-EBUSY), and hence cannot replace
the broken image.
Always close the block device in case no sub-image was mapped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Codename: Divo
Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel
4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell
Link: openwrt#17428
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq60xx series MR devices share some common attributes such as LED for
USB port.
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MR7500 features 4x QSGMII QCA8075 and 1x USXGMII (1/2.5/5 GbE)
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for EAP620 HD v1 and EAP660 HD v1 which is accepted by the stock UI.
Fix bug in ipq807x and ipq60xx makefiles so TPLINK_SUPPORT_STRING is handled properly.
Modify tplink-mkimage-2022 script and relevant makefiles to allow spaces in support strings (required for EAP620 HD v1 and EAP660 HD v1).
Installation steps are identical to EAP610-Outdoor:
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/18340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move "# CONFIG_NVMEM_LAYOUT_ASCII_ENV is not set" to the correct location.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18335
Signed-off-by: Nick Hainke <vincent@systemli.org>
RNDIS interface name change from usb0 to eth1
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18298
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using the pending ascii-eq-delim-env4 driver is a better way to read mac addresses since no
extra config is required
The change is like eacc4d8c9b, except for using smem for devinfo
thanks to @musashino205 for pointing out the simplification that removes
the extra partition
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18186
Signed-off-by: Robert Marko <robimarko@gmail.com>
arcadyan_mozart was incorrectly placed below asus devices
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18331
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for WAX620 and WAX630 which is accepted by the stock UI.
Must use 'Boot up Backup Firmware' button on stock upgrade page after install and reboot to swap partitions.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18334
Signed-off-by: Robert Marko <robimarko@gmail.com>
`bootargs = "console=ttyS0,57600";` is already defined on all
ramips target SoCs' dtsi. We don't need to override it with the
same value.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/18303
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000
RAM: 512 MiB
Flash: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Button: Reset, Switch
USB: 1x 3.0
SD slot: 1 in GL-AXT1800
Install via stock firmware:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
Install via uboot web failsafe:
Push the reset button for 5 seconds, then use broswer
to access http://192.168.1.1, and upload factory.ubi.
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make cpufreq work on different IPQ60xx SoC.
Also rebase ipq6018-cp-cpu.dtsi for mp5496.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh device tree, remove the useless sdhc2 aliases.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the minimal change for the upcoming patches.
Refresh the device tree of ipq807x at the same time.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Because of the dt-bindings error, these patches have not
been merged yet, and the driver part is fine.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be used by GL.iNet devices from other target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove a stray '|' character from 01_leds which has accidentally
been added.
Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than GPIO LEDs, PHY LEDs do have an address.
Fix node names such that all gpio-leds do *not* contain an '@' sign and
PHY leds which do have an address also do contain the '@' sign.
This is done to prevent more copy&paste'ry of non-complaint DT
fragments.
Fixes: 7cbe34170e ("mediatek: add support for the GL.iNet GL-MT3000")
Fixes: fe10f97439 ("filogic: add support for GL.iNet GL-MT6000")
Fixes: e8f7597317 ("mediatek: filogic: add support for Cudy RE3000 v1")
Fixes: c9cb6411c1 ("mediatek: add support for Cudy WR3000 v1")
Fixes: 7560af7647 ("mediatek: filogic: migrate ASUS TUF AX6000 to upstream PHY LED control")
Fixes: 25ea7ff393 ("mediatek: filogic: migrate Acer W6/W6d to upstream PHY LED control")
Fixes: d50d51d74e ("mediatek: filogic: migrate Zyxel NWA50AX Pro to upstream PHY LED control")
Fixes: b88de5d507 ("mediatek: filogic: migrate Zyxel EX5700 to upstream PHY LED control")
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Fixes: fd76a38190 ("mediatek: filogic: migrate SmartRG Bonanza to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All devices have already been migrated to the upstream PHY LED
API. This prevents users from adding new devices using this hack.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
According to the MT7620A hardware datasheet, GPIO/14 was originally used for RIN of UARTF, but is now used as the WPS LED.
Corrected pinctrl to ensure it works properly in the future.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link TL-WR1043ND family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link Archer C7 v1/2/3 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link TL-WDR4300 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ar8216 switch driver supports exposing configuration of AR8327 and
AR8337 switch LEDs to the userspace, however it is only configurable
through platform data, causing the devices ported from ar71xx target to
lack the support.
Since there is still a long way to go until we can migrate the target to
qca8k, an interim solution is needed.
Extend ar8327_hw_config_of function to parse a "leds"
subnode, which will populate the missing platform data based on device
tree contents, and restore the existing support for the LEDs.
Standard bindings apply, mapping "reg" property to LED index, with
addition of "qca,led-mode" property, which selects HW (0) or SW (1)
mode, defaulting to HW mode.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch LEDs configured as active-low remain low instead of high upon
initialization, because in ar8327_leds_init, no distinction is made with
regards to LED pattern based on active_low property - only whether HW
mode is active. Select the proper initial pattern based also on
active_low to fix that.
While at that, simplify the equation ruling pattern selection for
setting brightness, avoiding unnecessary binary XOR operation, not
really valid for 'bool' type.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Devices with chipidea usb controller does not detect usb hub after
phy-names change to "usb", revert it back to "usb-phy"
Fixes: 787cb9d87e ("ath79: change phy-names to only usb")
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18230
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing LEDs and modem control for ASUS 4G-AX56
- wifi2.4G white
- wifi5G white
- wan two-coloured, white and red
- modem four-coloured white, blue, yellow and red
change
label = "xxxx:modem";
to
color = <LED_COLOR_ID_xxxx>;
function = LED_FUNCTION_MOBILE;
- rssi-1 white
- rssi-2 white
- rssi-3 white
and modem reboot and reset
Combined into one commit
Signed-off-by: Henrik Ginstmark <henrik@ginstmark.se>
Link: https://github.com/openwrt/openwrt/pull/17927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With upstream changes hitting kernel 6.4 the dtb for u7623 ends up with
both mac (gmac) disabled, since this is now the default status in
mt7623.dtsi. Fix this by including mt7623a.dtsi (which already has all
necessary bits) and enabling all revlevant ports. This will also do
a side hustle of assigning proper clocks for power controller and
specifying proper power domain for few devices.
Link: https://lore.kernel.org/all/20230210182505.24597-1-arinc.unal@arinc9.com
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250304164507.60511-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since 24.10.0, eth0, used for the WAN interface, does not work. From dmesg:
...
[ 1.831126] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.846204] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
...
[ 1.933969] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.967668] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.975999] mt7530-mdio mdio-bus:1f eth0 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=21)
[ 1.986907] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1.987149] mtk_soc_eth 1e100000.ethernet eth0: error -17 registering interface eth0
[ 2.004157] mt7530-mdio mdio-bus:1f eth1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.017698] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.024849] DSA: tree 0 setup
...
[ 4.249680] mtk_soc_eth 1e100000.ethernet dsa: renamed from eth0
...
Like #15865, it seems that gmac0 does not rename eth0 to dsa until after the
switch ports are initialized, leading to a name collision (error -17 = EEXIST).
This patch follows #17062 by using openwrt,netdev-name to fix the collision.
Signed-off-by: J. S. Seldenthuis <jseldenthuis@lely.com>
Link: https://github.com/openwrt/openwrt/pull/18082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
