aadcb4abef
Specifications:
SOC: Atheros AR9344 @ 560MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR (128 MiB)
WIFI1: Atheros AR9340 5.0GHz (SoC)
WIFI2: Atheros AR9280 2.4GHz
SWITCH: Atheros AR8327 (5x Gigabit (1x WAN, 4x LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
USB: One USB 2.0 Port
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(GND, TX, RX, VCC - GND is next to the UART silk screen)
Flashing Instructions:
If your device still has vulnerable firmware, then existing installation
instructions can be used. Devices currently running ar71xx firmware can
be upgraded directly, although ar71xx firmware will complain,
because of changed metadata format. So you'll have to force the upgrade.
If your firmware is too new, there are two options
- temporarily adding a SPI-NOR flash to boot initramfs from
(recommended)
- patching NAND image with initramfs with external programmer
(recommended if and only if you have access to 360-clip, or
similar device, that doesn't require desoldering a TSOP48 chip))
Since this device is brought over from an old AR71xx, there's
already a wiki-page with detailed instructions:
<https://openwrt.org/toh/meraki/z1>
Installing from SPI-NOR:
- Download pre-built image from
<https://github.com/Leo-PL/OpenWrt-Meraki-Z1>
or assemble your own by splicing
router-u-boot <https://github.com/CodeFetch/router-u-boot>
image for TP-Link WDR4300 with Z1 initramfs in uImage format.
To build uImage initramfsf from source, remove the "KERNEL_INITRAMFS"
variable from target/linux/ath79/image/nand.mk for Z1.
Put the U-boot image at offset 0, initramfs at offset 131072.
- Write the image to an 8MB (or greater) SPI flash
- Temporarily bridge - or solder in a 220-ohm resistor between pins 6
and 8 of the SPI-NOR chip to override boot source to SPI
- When the initramfs first boots, write the standard initramfs to NAND,
to both 'kernel' and 'recovery' partitions
$ mtd write /tmp/openwrt-ath79-nand-meraki_z1-initramfs-kernel.bin kernel
$ mtd write /tmp/openwrt-ath79-nand-meraki_z1-initramfs-kernel.bin recovery
Now you can disconnect the resistor and try to boot the system from
NAND. If it works, continue with installation, as described for legacy
method using vulnerable stock firmware.
- When done, you can remove SPI-NOR chip and the resistor altogether,
it can be reused to perform installation on other devices,
or act as a recovery boot source if needed, if the recovery initramfs
fails for any reason.
Installing by patching NAND
- If you'd like to desolder NAND to perform this, I highly advise
against it, use SPI-NOR method above instead.
- If you have external programmer and a NAND clip, read out the whole
chip image, while keeping the device in reset by shorting SRST
(pin 11) to ground in JTAG connector,
and store a backup in a safe place.
- Patch the chip image with initramfs for raw NAND from
<https://github.com/Leo-PL/OpenWrt-Meraki-Z1>, by using a script
there, or manually:
$ dd if=openwrt-ath79-nand-meraki_z1-initramfs-kernel-rawnand.bin of=z1_dump.img bs=135168 seek=1 conv=notrunc
$ dd if=openwrt-ath79-nand-meraki_z1-initramfs-kernel-rawnand.bin of=z1_dump.img bs=135168 seek=65 conv=notrunc
This will write the initramfs to both kernel and recovery partitions,
which is highly recommended, as due to device architecture it is
notoriously hard to unbrick.
- Write the image back to the NAND, again, keeping the CPU in the reset.
- When the unit boots to initramfs, proceed as per existing instructions
for volnerable firmware.
Legacy installation on vulnerable stock firmware:
The gist:
1. Get a root-shell on the device (see wiki). (needs UART access)
2. make a backup (to a PC/safe location) of the existing Meraki
firmware.
3. copy over the OpenWrt initramfs kernel for the Z1.
This gets written into the kernel NAND partition.
(Verify that written image is complete!)
After the following reboot and successfull boot of the staging
OpenWrt initramfs image:
4. Free up space by removing Meraki firmware partitions from UBI volume
to free up space for OpenWrt (example given for the latest wired-14
version):
$ ubirmvol -N storage /dev/ubi0
$ ubirmvol -N rootfs-wired-14-202005181203-G201ba9ed-rel-gazebo-1 /dev/ubi0
$ ubirmvol -N rootfs-wired-14-202005181203-G201ba9ed-rel-gazebo-2 /dev/ubi0
4. copy over the sysupgrade.bin for the router and use sysupgrade
to make the installation permanent.
Notable changes from ar71xx support:
- LED colors are now different, because nu801 userspace driver is used
for the RGB LED.
Acknowledgments:
- Hal Martin, for providing additional devices for research, including
one modded for SPI boot and with removable NAND
- Christian Lamparter for initial device tree and image configuration
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Finished support, updated commit message with new installation
methods]
Co-authored-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17665
Signed-off-by: Robert Marko <robimarko@gmail.com>
568 lines
16 KiB
Makefile
568 lines
16 KiB
Makefile
define Build/dongwon-header
|
|
head -c 4 $@ > $@.tmp
|
|
head -c 8 /dev/zero >> $@.tmp
|
|
tail -c +9 $@ >> $@.tmp
|
|
( \
|
|
header_crc="$$(head -c 68 $@.tmp | gzip -c | \
|
|
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
|
|
printf "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@.tmp bs=4 count=1 seek=1 conv=notrunc \
|
|
)
|
|
mv $@.tmp $@
|
|
endef
|
|
|
|
define Build/meraki-header
|
|
-$(STAGING_DIR_HOST)/bin/mkmerakifw \
|
|
-B $(1) -s \
|
|
-i $@ \
|
|
-o $@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Build/meraki-old-nand
|
|
-$(STAGING_DIR_HOST)/bin/mkmerakifw-old \
|
|
-B $(1) -s \
|
|
-i $@ \
|
|
-o $@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
# attention: only zlib compression is allowed for the boot fs
|
|
define Build/zyxel-buildkerneljffs
|
|
mkdir -p $@.tmp/boot
|
|
cp $@ $@.tmp/boot/vmlinux.lzma.uImage
|
|
$(STAGING_DIR_HOST)/bin/mkfs.jffs2 \
|
|
--big-endian --squash-uids -v -e 128KiB -q -f -n -x lzma -x rtime \
|
|
-o $@ \
|
|
-d $@.tmp
|
|
rm -rf $@.tmp
|
|
endef
|
|
|
|
define Build/zyxel-factory
|
|
let \
|
|
maxsize="$(call exp_units,$(RAS_ROOTFS_SIZE))"; \
|
|
let size="$$(stat -c%s $@)"; \
|
|
if [ $$size -lt $$maxsize ]; then \
|
|
$(STAGING_DIR_HOST)/bin/mkrasimage \
|
|
-b $(RAS_BOARD) \
|
|
-v $(RAS_VERSION) \
|
|
-r $@ \
|
|
-s $$maxsize \
|
|
-o $@.new \
|
|
-l 131072 \
|
|
&& mv $@.new $@ ; \
|
|
fi
|
|
endef
|
|
|
|
define Device/8dev_rambutan
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Rambutan
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES := factory.bin sysupgrade.tar
|
|
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-ubi
|
|
endef
|
|
TARGET_DEVICES += 8dev_rambutan
|
|
|
|
define Device/aerohive_hiveap-121
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Aerohive
|
|
DEVICE_MODEL := HiveAP 121
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 116m
|
|
KERNEL_SIZE := 5120k
|
|
UBINIZE_OPTS := -E 5
|
|
SUPPORTED_DEVICES += hiveap-121
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += aerohive_hiveap-121
|
|
|
|
define Device/domywifi_dw33d
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := DomyWifi
|
|
DEVICE_MODEL := DW33D
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-storage kmod-usb-ledtrig-usbport \
|
|
kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 98304k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += domywifi_dw33d
|
|
|
|
define Device/dongwon_dw02-412h
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := Dongwon T&I
|
|
DEVICE_MODEL := DW02-412H
|
|
DEVICE_ALT0_VENDOR := KT
|
|
DEVICE_ALT0_MODEL := GiGA WiFi home
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
KERNEL_SIZE := 8192k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL := $$(KERNEL) | dongwon-header
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/dongwon_dw02-412h-64m
|
|
$(Device/dongwon_dw02-412h)
|
|
DEVICE_VARIANT := (64M)
|
|
DEVICE_ALT0_VARIANT := (64M)
|
|
IMAGE_SIZE := 49152k
|
|
endef
|
|
TARGET_DEVICES += dongwon_dw02-412h-64m
|
|
|
|
define Device/dongwon_dw02-412h-128m
|
|
$(Device/dongwon_dw02-412h)
|
|
DEVICE_VARIANT := (128M)
|
|
DEVICE_ALT0_VARIANT := (128M)
|
|
IMAGE_SIZE := 114688k
|
|
endef
|
|
TARGET_DEVICES += dongwon_dw02-412h-128m
|
|
|
|
define Device/glinet_gl-ar300m-common-nand
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR300M
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 16000k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
endef
|
|
|
|
define Device/glinet_gl-ar300m-nand
|
|
$(Device/glinet_gl-ar300m-common-nand)
|
|
DEVICE_VARIANT := NAND
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
SUPPORTED_DEVICES += glinet,gl-ar300m-nor
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m-nand
|
|
|
|
define Device/glinet_gl-ar300m-nor
|
|
$(Device/glinet_gl-ar300m-common-nand)
|
|
DEVICE_VARIANT := NOR
|
|
SUPPORTED_DEVICES += glinet,gl-ar300m-nand gl-ar300m
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m-nor
|
|
|
|
define Device/glinet_gl-ar750s-common
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR750S
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2 \
|
|
kmod-usb-storage block-mount
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
|
|
define Device/glinet_gl-ar750s-nor-nand
|
|
$(Device/glinet_gl-ar750s-common)
|
|
DEVICE_VARIANT := NOR/NAND
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
SUPPORTED_DEVICES += glinet,gl-ar750s-nor
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar750s-nor-nand
|
|
|
|
define Device/glinet_gl-ar750s-nor
|
|
$(Device/glinet_gl-ar750s-common)
|
|
DEVICE_VARIANT := NOR
|
|
SUPPORTED_DEVICES += gl-ar750s glinet,gl-ar750s glinet,gl-ar750s-nor-nand
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar750s-nor
|
|
|
|
define Device/glinet_gl-e750
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-E750
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2 \
|
|
kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
SUPPORTED_DEVICES += gl-e750
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 131072k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-e750
|
|
|
|
define Device/glinet_gl-s200-common
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-S200
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-serial-ch341
|
|
SUPPORTED_DEVICES += gl-s200 glinet,gl-s200
|
|
endef
|
|
|
|
define Device/glinet_gl-s200-nor
|
|
$(Device/glinet_gl-s200-common)
|
|
DEVICE_VARIANT := NOR
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-s200-nor
|
|
|
|
define Device/glinet_gl-s200-nor-nand
|
|
$(Device/glinet_gl-s200-common)
|
|
DEVICE_VARIANT := NOR/NAND
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
IMAGES += factory.img
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
SUPPORTED_DEVICES += gl-s200 glinet,gl-s200
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-s200-nor-nand
|
|
|
|
define Device/glinet_gl-xe300
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-XE300
|
|
DEVICE_PACKAGES := kmod-usb2 block-mount kmod-usb-serial-ch341 \
|
|
kmod-usb-serial-option kmod-usb-net-qmi-wwan uqmi
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 131072k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-xe300
|
|
|
|
define Device/glinet_gl-x1200-common
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-X1200
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct-htt kmod-usb2 \
|
|
kmod-usb-storage block-mount kmod-usb-net-qmi-wwan uqmi
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
|
|
define Device/glinet_gl-x1200-nor-nand
|
|
$(Device/glinet_gl-x1200-common)
|
|
DEVICE_VARIANT := NOR/NAND
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 131072k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-x1200-nor-nand
|
|
|
|
define Device/glinet_gl-x1200-nor
|
|
$(Device/glinet_gl-x1200-common)
|
|
DEVICE_VARIANT := NOR
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-x1200-nor
|
|
|
|
define Device/linksys_ea4500-v3
|
|
SOC := qca9558
|
|
DEVICE_COMPAT_VERSION := 1.1
|
|
DEVICE_COMPAT_MESSAGE := Partition table has been changed. Please \
|
|
install kmod-mtd-rw and erase mtd8 (syscfg) before upgrade \
|
|
to keep configures, or forcibly flash factory image to mtd5 \
|
|
(firmware) partition with mtd tool to discard configures but \
|
|
claim additional space immediately.
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA4500
|
|
DEVICE_VARIANT := v3
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 128256k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
LINKSYS_HWNAME := EA4500V3
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
|
|
UBINIZE_OPTS := -E 5
|
|
endef
|
|
TARGET_DEVICES += linksys_ea4500-v3
|
|
|
|
define Device/meraki_mr18
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := Meraki
|
|
DEVICE_MODEL := MR18
|
|
DEVICE_PACKAGES := kmod-leds-uleds kmod-spi-gpio nu801
|
|
KERNEL_SIZE := 8m
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
LOADER_TYPE := bin
|
|
LZMA_TEXT_START := 0x82800000
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | meraki-header MR18
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
SUPPORTED_DEVICES += mr18
|
|
endef
|
|
TARGET_DEVICES += meraki_mr18
|
|
|
|
define Device/meraki_z1
|
|
SOC = ar9344
|
|
DEVICE_VENDOR := Meraki
|
|
DEVICE_MODEL := Z1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-owl-loader \
|
|
kmod-leds-uleds kmod-spi-gpio nu801 -uboot-envtools
|
|
KERNEL_SIZE := 8064k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
LOADER_TYPE := bin
|
|
LZMA_TEXT_START := 0x82800000
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
pad-to $$(BLOCKSIZE) | meraki-old-nand z1
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
SUPPORTED_DEVICES += z1
|
|
endef
|
|
TARGET_DEVICES += meraki_z1
|
|
|
|
# fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header + '\0')
|
|
define Device/netgear_ath79_nand
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 25600k
|
|
KERNEL := kernel-bin | append-dtb | lzma | \
|
|
pad-offset $$(BLOCKSIZE) 129 | uImage lzma | pad-extra 1 | \
|
|
append-uImage-fakehdr filesystem $$(UIMAGE_MAGIC)
|
|
IMAGES := sysupgrade.bin factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | netgear-dni
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
UBINIZE_OPTS := -E 5
|
|
endef
|
|
|
|
define Device/netgear_pgzng1
|
|
SOC := ar9344
|
|
DEVICE_MODEL := PGZNG1
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := Pulse Gateway
|
|
DEVICE_ALT0_VENDOR := ADT
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-i2c-gpio \
|
|
kmod-leds-pca955x kmod-rtc-isl1208 kmod-spi-dev
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 83968k
|
|
PAGESIZE := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += netgear_pgzng1
|
|
|
|
define Device/netgear_r6100
|
|
SOC := ar9344
|
|
DEVICE_MODEL := R6100
|
|
UIMAGE_MAGIC := 0x36303030
|
|
NETGEAR_BOARD_ID := R6100
|
|
NETGEAR_HW_ID := 29764434+0+128+128+2x2+2x2
|
|
$(Device/netgear_ath79_nand)
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += netgear_r6100
|
|
|
|
define Device/netgear_wndr3700-v4
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v4
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR3700v4
|
|
NETGEAR_HW_ID := 29763948+128+128
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700-v4
|
|
|
|
define Device/netgear_wndr4300
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR4300
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR4300
|
|
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300
|
|
|
|
define Device/netgear_wndr4300sw
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR4300SW
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR4300SW
|
|
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300sw
|
|
|
|
define Device/netgear_wndr4300tn
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR4300TN
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR4300TN
|
|
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300tn
|
|
|
|
define Device/netgear_wndr4300-v2
|
|
SOC := qca9563
|
|
DEVICE_COMPAT_VERSION := 1.1
|
|
DEVICE_COMPAT_MESSAGE := Partition table has been changed to fix the \
|
|
first reboot issue. Please reflash factory image with nmrp or tftp.
|
|
DEVICE_MODEL := WNDR4300
|
|
DEVICE_VARIANT := v2
|
|
UIMAGE_MAGIC := 0x27051956
|
|
NETGEAR_BOARD_ID := WNDR4500series
|
|
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012175
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300-v2
|
|
|
|
define Device/netgear_wndr4500-v3
|
|
SOC := qca9563
|
|
DEVICE_COMPAT_VERSION := 1.1
|
|
DEVICE_COMPAT_MESSAGE := Partition table has been changed to fix the \
|
|
first reboot issue. Please reflash factory image with nmrp or tftp.
|
|
DEVICE_MODEL := WNDR4500
|
|
DEVICE_VARIANT := v3
|
|
UIMAGE_MAGIC := 0x27051956
|
|
NETGEAR_BOARD_ID := WNDR4500series
|
|
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012173
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4500-v3
|
|
|
|
define Device/zte_mf28x_common
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ZTE
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
LOADER_TYPE := bin
|
|
LZMA_TEXT_START := 0x82800000
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/zte_mf281
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF281
|
|
KERNEL_SIZE := 6144k
|
|
IMAGE_SIZE := 29696k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-rndis \
|
|
-ath10k-board-qca9888 ipq-wifi-zte_mf286c \
|
|
kmod-usb-acm comgt-ncm
|
|
endef
|
|
TARGET_DEVICES += zte_mf281
|
|
|
|
define Device/zte_mf282
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF282
|
|
DEVICE_PACKAGES += ath10k-firmware-qca988x-ct kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option uqmi
|
|
endef
|
|
TARGET_DEVICES += zte_mf282
|
|
|
|
define Device/zte_mf286
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286
|
|
DEVICE_PACKAGES += ath10k-firmware-qca988x-ct ath10k-firmware-qca9888-ct \
|
|
-ath10k-board-qca9888 ipq-wifi-zte_mf286ar \
|
|
kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
endef
|
|
TARGET_DEVICES += zte_mf286
|
|
|
|
define Device/zte_mf286a
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286A
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-qmi-wwan \
|
|
-ath10k-board-qca9888 ipq-wifi-zte_mf286ar \
|
|
kmod-usb-serial-option uqmi
|
|
endef
|
|
TARGET_DEVICES += zte_mf286a
|
|
|
|
define Device/zte_mf286c
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286C
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-qmi-wwan \
|
|
-ath10k-board-qca9888 ipq-wifi-zte_mf286c \
|
|
kmod-usb-serial-option uqmi
|
|
endef
|
|
TARGET_DEVICES += zte_mf286c
|
|
|
|
define Device/zte_mf286r
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286R
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-rndis kmod-usb-acm \
|
|
comgt-ncm
|
|
endef
|
|
TARGET_DEVICES += zte_mf286r
|
|
|
|
define Device/zyxel_nbg6716
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Zyxel
|
|
DEVICE_MODEL := NBG6716
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct \
|
|
ath10k-firmware-qca988x-ct
|
|
RAS_BOARD := NBG6716
|
|
RAS_ROOTFS_SIZE := 29696k
|
|
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none | \
|
|
zyxel-buildkerneljffs | check-size 4096k
|
|
IMAGES := sysupgrade.tar sysupgrade-4M-Kernel.bin factory.bin
|
|
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$$(BLOCKSIZE) | \
|
|
sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
IMAGE/sysupgrade-4M-Kernel.bin/squashfs := append-kernel | \
|
|
pad-to $$$$(KERNEL_SIZE) | append-ubi | pad-to 263192576 | gzip
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
zyxel-factory
|
|
UBINIZE_OPTS := -E 5
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6716
|
|
|
|
define Device/zyxel_emg2926_q10a
|
|
$(Device/zyxel_nbg6716)
|
|
DEVICE_MODEL := EMG2926-Q10A
|
|
RAS_BOARD := AAVK-EMG2926Q10A
|
|
endef
|
|
TARGET_DEVICES += zyxel_emg2926_q10a
|