catspeed-cc/openwrt
1
1
Fork 0
Code
785492e4c1
openwrt/target/linux/qualcommax/image/ipq807x.mk
Michael Lotz 785492e4c1 qualcommax: ipq807x: add Zyxel NWA110AX support 
The Zyxel NWA110AX is a dual band 2x2:2 802.11ax wireless access point
with PoE.

The device is very similar to the NWA210AX except for being 2x2 instead
of 4x4 in the 5GHz band and not having the 2.5GbE ethernet port. This
commit factors out a common DTS and device definition and reuses it for
both devices.

Hardware:
* SoC: Qualcomm IPQ8070A
* RAM: 1GiB 1x Samsung K4A8G165WC-BCTD
* Flash: 8MiB Winbond W25Q64DW SPI-NOR, 256MiB Winbond W29N02GZ SPI-NAND
* WLAN 2.4GHz: QCN5024 2x2:2 802.11b/g/n/ax
* WLAN 5GHz: QCN5054 2x2:2 802.11n/ac/ax
* Ethernet: 1x 1GbE with AR8033 PHY
* Serial Config: 3.3V TTL 115200-8-N-1, externally accessible
* Serial Layout: GND TX RX 3.3V (don't connect, marked with triangle)
* LEDs: 1x red, 1x green, 1x blue, 1x white
* Buttons: 1x reset

MAC addresses:
* Uplink: base address on label
* 2.4GHz WLAN: base + 1
* 5GHZ WLAN: base + 2

Flashing Notes:
The device uses a dual-image setup and OpenWrt can only be installed as
image 0. When the currently running stock firmware is image 0, OpenWrt
will be installed as image 1, fail to boot and the device returns to stock
firmware. If this happens, install any version of stock firmware so that
it runs as image 1, before installing OpenWrt. Alternatively, if there
already is a valid stock firmware in image 1, the "debug dual-image show"
and "debug dual-image set boot-image image1" commands can be used in the
stock CLI via serial/SSH/telnet to switch to image 1.

Flashing with Stock Web Interface:
* Get the OpenWrt factory image and rename it to a shorter name, for
  example "openwrt.bin" (the stock firmware has a character limit)
* In the web interface, go to "Maintenance" -> "File Manager" ->
  "Firmware Package" (or click the link next to "Firmware Version" under
  "Device Information" on the dashboard)
* Under "Upload File" browse to the renamed OpenWrt factory image and
  click on "Upload"

Switch Boot Image:
* OpenWrt to stock: "zyxel-bootconfig-ipq807x set image1"
* Stock to OpenWrt: "debug dual-image set boot-image image0"

Unbrick / Revert to Stock with the Boot Module:
* Disconnect the device from power
* Configure your machine to 192.168.1.103/24 and start a TFTP server
* Put the stock firmware image into the TFTP server root and rename it to
  "ZLD-current"
* Establish a serial connection to the device through the console port
* Connect the device to power
* When prompted, press a key to abort automatic boot and enter debug mode
* Use the "atnz" command to flash the firmware image
* Use the "atgo" command to boot from the newly flashed image

Signed-off-by: Michael Lotz <mmlr@mlotz.ch>
Link: https://github.com/openwrt/openwrt/pull/21849
Signed-off-by: Robert Marko <robimarko@gmail.com>
2026-02-13 21:35:49 +01:00

637 lines
17 KiB
Makefile
Raw Blame History

DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID TPLINK_SUPPORT_STRING ZYXEL_MODEL_ID
define Build/asus-fake-ramdisk
rm -rf $(KDIR)/tmp/fakerd
dd if=/dev/zero bs=32 count=1 > $(KDIR)/tmp/fakerd
$(info KERNEL_INITRAMFS is $(KERNEL_INITRAMFS))
endef
define Build/asus-fake-rootfs
$(eval comp=$(word 1,$(1)))
$(eval filepath=$(word 2,$(1)))
$(eval filecont=$(word 3,$(1)))
rm -rf $(KDIR)/tmp/fakefs $(KDIR)/tmp/fakehsqs
mkdir -p $(KDIR)/tmp/fakefs/$$(dirname $(filepath))
echo '$(filecont)' > $(KDIR)/tmp/fakefs/$(filepath)
$(STAGING_DIR_HOST)/bin/mksquashfs4 $(KDIR)/tmp/fakefs $(KDIR)/tmp/fakehsqs -comp $(comp) \
-b 4096 -no-exports -no-sparse -no-xattrs -all-root -noappend \
$(wordlist 4,$(words $(1)),$(1))
endef
define Build/asus-trx
$(STAGING_DIR_HOST)/bin/asusuimage $(wordlist 1,$(words $(1)),$(1)) -i $@ -o $@.new
mv $@.new $@
endef
define Build/netgear-rbx750-qsdk-ipq-factory
$(CP) $(FLASH_SCRIPT) $(KDIR_TMP)/
echo "VERSION : V8.0.0.0_$(LINUX_VERSION)" > $@.metadata
echo "MODEL_ID : $(DEVICE_MODEL)" >> $@.metadata
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its $(FLASH_SCRIPT) txt $@.metadata ubi $@
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
@mv $@.new $@
endef
define Build/wax6xx-netgear-tar
mkdir $@.tmp
mv $@ $@.tmp/nand-ipq807x-apps.img
md5sum $@.tmp/nand-ipq807x-apps.img | cut -c 1-32 > $@.tmp/nand-ipq807x-apps.md5sum
echo $(DEVICE_MODEL) > $@.tmp/metadata.txt
echo $(DEVICE_MODEL)"_V99.9.9.9" > $@.tmp/version
tar -C $@.tmp/ -cf $@ .
rm -rf $@.tmp
endef
define Build/zyxel-nwax10ax-fit
$(TOPDIR)/scripts/mkits-zyxel-fit-filogic.sh \
$@.its $@ "$(ZYXEL_MODEL_ID) ff ff ff ff ff ff ff ff"
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
@mv $@.new $@
endef
define Device/aliyun_ap8220
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Aliyun
DEVICE_MODEL := AP8220
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ac02
SOC := ipq8071
DEVICE_PACKAGES := ipq-wifi-aliyun_ap8220
endef
TARGET_DEVICES += aliyun_ap8220
define Device/arcadyan_aw1000
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Arcadyan
DEVICE_MODEL := AW1000
BLOCKSIZE := 256k
PAGESIZE := 4096
DEVICE_DTS_CONFIG := config@hk09
SOC := ipq8072
DEVICE_PACKAGES := ipq-wifi-arcadyan_aw1000 kmod-spi-gpio \
kmod-gpio-nxp-74hc164 kmod-usb-serial-option uqmi
endef
TARGET_DEVICES += arcadyan_aw1000
define Device/asus_rt-ax89x
DEVICE_VENDOR := Asus
DEVICE_MODEL := RT-AX89X
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk01
SOC := ipq8074
DEVICE_PACKAGES := kmod-hwmon-gpiofan ipq-wifi-asus_rt-ax89x
KERNEL_NAME := vmlinux
KERNEL := kernel-bin | libdeflate-gzip
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin/squashfs := \
append-kernel | asus-fake-ramdisk |\
multiImage gzip $$(KDIR)/tmp/fakerd $$(KDIR)/image-$$(DEVICE_DTS).dtb |\
sysupgrade-tar kernel=$$$$@ | append-metadata
ifeq ($(IB),)
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.trx initramfs-uImage.itb
ARTIFACT/initramfs-uImage.itb := \
append-image-stage initramfs-kernel.bin | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
ARTIFACT/initramfs-factory.trx := \
append-image-stage initramfs-kernel.bin |\
asus-fake-rootfs xz /lib/firmware/IPQ8074A/fw_version.txt "fake" -no-compression |\
multiImage gzip $$(KDIR)/tmp/fakehsqs $$(KDIR)/image-$$(DEVICE_DTS).dtb |\
asus-trx -v 2 -n RT-AX89U -b 388 -e 49000
endif
endif
endef
TARGET_DEVICES += asus_rt-ax89x
define Device/buffalo_wxr-5950ax12
$(call Device/FitImage)
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WXR-5950AX12
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk01
SOC := ipq8074
DEVICE_PACKAGES := ipq-wifi-buffalo_wxr-5950ax12
endef
TARGET_DEVICES += buffalo_wxr-5950ax12
define Device/cmcc_rm2-6
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := CMCC
DEVICE_MODEL := RM2-6
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ac02
SOC := ipq8070
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
DEVICE_PACKAGES := ipq-wifi-cmcc_rm2-6 kmod-hwmon-gpiofan
endef
TARGET_DEVICES += cmcc_rm2-6
define Device/compex_wpq873
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPQ873
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk09.wpq873
SOC := ipq8072
DEVICE_PACKAGES := ipq-wifi-compex_wpq873
IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += compex_wpq873
define Device/dynalink_dl-wrx36
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Dynalink
DEVICE_MODEL := DL-WRX36
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@rt5010w-d350-rev0
SOC := ipq8072
DEVICE_PACKAGES := ipq-wifi-dynalink_dl-wrx36
endef
TARGET_DEVICES += dynalink_dl-wrx36
define Device/edgecore_eap102
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edgecore
DEVICE_MODEL := EAP102
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ac02
SOC := ipq8071
DEVICE_PACKAGES := ipq-wifi-edgecore_eap102
IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += edgecore_eap102
define Device/edimax_cax1800
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edimax
DEVICE_MODEL := CAX1800
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ac03
SOC := ipq8070
DEVICE_PACKAGES := ipq-wifi-edimax_cax1800
endef
TARGET_DEVICES += edimax_cax1800
define Device/linksys_homewrk
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := HomeWRK
DEVICE_DTS_CONFIG := config@oak03
BLOCKSIZE := 256k
PAGESIZE := 4096
IMAGE_SIZE := 475m
NAND_SIZE := 1024m
SOC := ipq8174
DEVICE_PACKAGES += kmod-leds-pca963x ipq-wifi-linksys_homewrk
endef
TARGET_DEVICES += linksys_homewrk
define Device/linksys_mx
$(call Device/FitImage)
DEVICE_VENDOR := Linksys
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 6144k
IMAGE_SIZE := 147456k
NAND_SIZE := 512m
SOC := ipq8072
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=$$$$(DEVICE_MODEL)
DEVICE_PACKAGES := kmod-leds-pca963x
endef
define Device/linksys_mx4x00
$(call Device/linksys_mx)
SOC := ipq8174
DEVICE_PACKAGES += ipq-wifi-linksys_mx4200
endef
define Device/linksys_mx4200v1
$(call Device/linksys_mx4x00)
DEVICE_MODEL := MX4200
DEVICE_VARIANT := v1
DEVICE_PACKAGES += kmod-hci-uart
endef
TARGET_DEVICES += linksys_mx4200v1
define Device/linksys_mx4200v2
$(call Device/linksys_mx4200v1)
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += linksys_mx4200v2
define Device/linksys_mx4300
$(call Device/linksys_mx4x00)
DEVICE_MODEL := MX4300
BLOCKSIZE := 256k
PAGESIZE := 4096
KERNEL_SIZE := 8192k
IMAGE_SIZE := 171264k
NAND_SIZE := 1024m
endef
TARGET_DEVICES += linksys_mx4300
define Device/linksys_mx5300
$(call Device/linksys_mx)
DEVICE_MODEL := MX5300
DEVICE_PACKAGES += kmod-rtc-ds1307 ipq-wifi-linksys_mx5300 \
kmod-ath10k-ct ath10k-firmware-qca9984-ct
endef
TARGET_DEVICES += linksys_mx5300
define Device/linksys_mx8500
$(call Device/linksys_mx)
DEVICE_MODEL := MX8500
DEVICE_PACKAGES += ipq-wifi-linksys_mx8500 kmod-ath11k-pci \
ath11k-firmware-qcn9074 kmod-hci-uart
endef
TARGET_DEVICES += linksys_mx8500
define Device/netgear_rax120v2
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := RAX120v2
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk01
SOC := ipq8074
KERNEL_SIZE := 29696k
NETGEAR_BOARD_ID := RAX120
NETGEAR_HW_ID := 29765589+0+512+1024+4x4+8x8
DEVICE_PACKAGES := ipq-wifi-netgear_rax120v2 kmod-spi-gpio \
kmod-spi-bitbang kmod-gpio-nxp-74hc164 kmod-hwmon-g762
ifeq ($(IB),)
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
IMAGES += web-ui-factory.img
IMAGE/web-ui-factory.img := append-image initramfs-uImage.itb | \
pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | \
netgear-dni
endif
endif
IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | \
append-metadata
endef
TARGET_DEVICES += netgear_rax120v2
define Device/netgear_rbx750
$(call Device/FitImage)
$(call Device/UbiFit)
SOC := ipq8074
DEVICE_VENDOR := Netgear
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-netgear_rbk750 kmod-leds-lp5562
DEVICE_DTS_CONFIG := config@oak03
FLASH_SCRIPT := netgear_rbx750.bootscript
IMAGES += factory.chk
IMAGE/factory.chk := append-ubi | netgear-rbx750-qsdk-ipq-factory | \
netgear-chk
endef
define Device/netgear_rbr750
$(call Device/netgear_rbx750)
DEVICE_MODEL := RBR750
NETGEAR_BOARD_ID := U12H415T00_NETGEAR
endef
TARGET_DEVICES += netgear_rbr750
define Device/netgear_rbs750
$(call Device/netgear_rbx750)
DEVICE_MODEL := RBS750
NETGEAR_BOARD_ID := U12H416T00_NETGEAR
endef
TARGET_DEVICES += netgear_rbs750
define Device/netgear_sxk80
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_PACKAGES += ipq-wifi-netgear_sxk80
DEVICE_VENDOR := Netgear
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk01
SOC := ipq8074
KERNEL_SIZE := 6272k
NETGEAR_HW_ID := 29766265+0+512+1024+4x4+4x4+4x4
endef
define Device/netgear_sxr80
$(call Device/netgear_sxk80)
DEVICE_MODEL := SXR80
NETGEAR_BOARD_ID := SXR80
endef
TARGET_DEVICES += netgear_sxr80
define Device/netgear_sxs80
$(call Device/netgear_sxk80)
DEVICE_MODEL := SXS80
NETGEAR_BOARD_ID := SXS80
endef
TARGET_DEVICES += netgear_sxs80
define Device/netgear_wax218
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAX218
DEVICE_DTS_CONFIG := config@hk07
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq8072
ifeq ($(IB),)
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := web-ui-factory.fit
ARTIFACT/web-ui-factory.fit := append-image initramfs-uImage.itb | \
ubinize-kernel | qsdk-ipq-factory-nand
endif
endif
DEVICE_PACKAGES := kmod-spi-gpio kmod-spi-bitbang kmod-gpio-nxp-74hc164 \
ipq-wifi-netgear_wax218
endef
TARGET_DEVICES += netgear_wax218
define Device/netgear_wax620
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAX620
DEVICE_DTS_CONFIG := config@hk07
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq8072
IMAGES += ui-factory.tar
IMAGE/ui-factory.tar := append-ubi | qsdk-ipq-factory-nand | pad-to 4096 | wax6xx-netgear-tar
DEVICE_PACKAGES := kmod-spi-gpio kmod-gpio-nxp-74hc164 \
ipq-wifi-netgear_wax620
endef
TARGET_DEVICES += netgear_wax620
define Device/netgear_wax630
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAX630
DEVICE_DTS_CONFIG := config@hk01
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq8074
IMAGES += ui-factory.tar
IMAGE/ui-factory.tar := append-ubi | qsdk-ipq-factory-nand | pad-to 4096 | wax6xx-netgear-tar
DEVICE_PACKAGES := kmod-spi-gpio ipq-wifi-netgear_wax630
endef
TARGET_DEVICES += netgear_wax630
define Device/prpl_haze
$(call Device/FitImage)
$(call Device/EmmcImage)
DEVICE_VENDOR := prpl Foundation
DEVICE_MODEL := Haze
DEVICE_DTS_CONFIG := config@hk09
SOC := ipq8072
DEVICE_PACKAGES := ath11k-firmware-qcn9074 ipq-wifi-prpl_haze kmod-ath11k-pci \
kmod-fs-f2fs f2fs-tools kmod-leds-lp5562
endef
TARGET_DEVICES += prpl_haze
define Device/qnap_301w
$(call Device/FitImage)
$(call Device/EmmcImage)
DEVICE_VENDOR := QNAP
DEVICE_MODEL := 301w
DEVICE_DTS_CONFIG := config@hk01
KERNEL_SIZE := 16384k
SOC := ipq8072
DEVICE_PACKAGES := kmod-fs-f2fs f2fs-tools ipq-wifi-qnap_301w
endef
TARGET_DEVICES += qnap_301w
define Device/redmi_ax6
$(call Device/xiaomi_ax3600)
DEVICE_VENDOR := Redmi
DEVICE_MODEL := AX6
DEVICE_PACKAGES := ipq-wifi-redmi_ax6
endef
TARGET_DEVICES += redmi_ax6
define Device/spectrum_sax1v1k
$(call Device/FitImage)
$(call Device/EmmcImage)
DEVICE_VENDOR := Spectrum
DEVICE_MODEL := SAX1V1K
DEVICE_DTS_CONFIG := config@rt5010w-d187-rev6
SOC := ipq8072
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-fs-f2fs f2fs-tools ipq-wifi-spectrum_sax1v1k
endef
TARGET_DEVICES += spectrum_sax1v1k
define Device/tcl_linkhub-hh500v
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TCL
DEVICE_MODEL := LINKHUB HH500V
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk09
SOC := ipq8072
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
DEVICE_PACKAGES := ipq-wifi-tcl_linkhub-hh500v kmod-mhi-pci-generic \
kmod-mhi-wwan-ctrl kmod-mhi-wwan-mbim
endef
TARGET_DEVICES += tcl_linkhub-hh500v
define Device/tplink_deco-x80-5g
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Deco X80-5G
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk01.c5
SOC := ipq8074
DEVICE_PACKAGES := kmod-hwmon-gpiofan ipq-wifi-tplink_deco-x80-5g \
kmod-usb-serial-option kmod-usb-net-qmi-wwan
endef
TARGET_DEVICES += tplink_deco-x80-5g
define Device/tplink_eap620hd-v1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := EAP620 HD
DEVICE_VARIANT := v1
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq8072
DEVICE_PACKAGES := ipq-wifi-tplink_eap620hd-v1
IMAGES += web-ui-factory.bin
IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
TPLINK_SUPPORT_STRING := SupportList:\r\nEAP620 HD(TP-Link|UN|AX1800-D):1.0\r\n
endef
TARGET_DEVICES += tplink_eap620hd-v1
define Device/tplink_eap660hd-v1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := EAP660 HD
DEVICE_VARIANT := v1
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq8072
DEVICE_PACKAGES := ipq-wifi-tplink_eap660hd-v1
IMAGES += web-ui-factory.bin
IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
TPLINK_SUPPORT_STRING := SupportList:\r\nEAP660 HD(TP-Link|UN|AX3600-D):1.0\r\n
endef
TARGET_DEVICES += tplink_eap660hd-v1
define Device/xiaomi_ax3600
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := AX3600
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ac04
SOC := ipq8071
KERNEL_SIZE := 36608k
DEVICE_PACKAGES := ipq-wifi-xiaomi_ax3600 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct
ifeq ($(IB),)
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-uImage.itb | ubinize-kernel
endif
endif
endef
TARGET_DEVICES += xiaomi_ax3600
define Device/xiaomi_ax9000
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := AX9000
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk14
SOC := ipq8072
KERNEL_SIZE := 57344k
DEVICE_PACKAGES := ipq-wifi-xiaomi_ax9000 kmod-ath11k-pci ath11k-firmware-qcn9074 \
kmod-ath10k-ct ath10k-firmware-qca9887-ct
ifeq ($(IB),)
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-uImage.itb | ubinize-kernel
endif
endif
endef
TARGET_DEVICES += xiaomi_ax9000
define Device/yuncore_ax880
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Yuncore
DEVICE_MODEL := AX880
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk09
SOC := ipq8072
DEVICE_PACKAGES := ipq-wifi-yuncore_ax880
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += yuncore_ax880
define Device/zbtlink_zbt-z800ax
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-Z800AX
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@hk09
SOC := ipq8072
DEVICE_PACKAGES := ipq-wifi-zbtlink_zbt-z800ax
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += zbtlink_zbt-z800ax
define Device/zte_mf269
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := ZTE
DEVICE_MODEL := MF269
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ac04
SOC := ipq8071
KERNEL_SIZE := 53248k
DEVICE_PACKAGES := ipq-wifi-zte_mf269
endef
TARGET_DEVICES += zte_mf269
define Device/zyxel_nbg7815
$(call Device/FitImage)
$(call Device/EmmcImage)
DEVICE_VENDOR := ZYXEL
DEVICE_MODEL := NBG7815
DEVICE_DTS_CONFIG := config@nbg7815
SOC := ipq8074
DEVICE_PACKAGES := kmod-fs-f2fs f2fs-tools ipq-wifi-zyxel_nbg7815 kmod-ath11k-pci \
kmod-hci-uart kmod-hwmon-tmp103
endef
TARGET_DEVICES += zyxel_nbg7815
define Device/zyxel_nwax10ax_common
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Zyxel
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 61440k
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) | zyxel-nwax10ax-fit
endef
define Device/zyxel_nwa110ax
$(call Device/zyxel_nwax10ax_common)
DEVICE_MODEL := NWA110AX
DEVICE_DTS_CONFIG := config@ac01
SOC := ipq8070
DEVICE_PACKAGES := ipq-wifi-zyxel_nwa110ax zyxel-bootconfig-ipq807x kmod-leds-lp5562
ZYXEL_MODEL_ID := 59 e1
endef
TARGET_DEVICES += zyxel_nwa110ax
define Device/zyxel_nwa210ax
$(call Device/zyxel_nwax10ax_common)
DEVICE_MODEL := NWA210AX
DEVICE_DTS_CONFIG := config@ac02
SOC := ipq8071
DEVICE_PACKAGES := ipq-wifi-zyxel_nwa210ax zyxel-bootconfig-ipq807x kmod-leds-lp5562
ZYXEL_MODEL_ID := 5c e1
endef
TARGET_DEVICES += zyxel_nwa210ax
View Git Blame Copy Permalink