7e829b8209
The D-Link DNS-325 A1 is NAS with 2x HDD (3.5 inch) bays, 1x 10/100/1000Base-T port and 1x USB 2.0 port
Device specification:
SoC: Marvell 88F6281-A1 1.2 GHz
RAM: 256 MB (2xSEC K4T1G084QF-HCF7:128Mx8 @400 CL6)
Flash: 128 MB (SAMSUNG 946 K9F1G08U0B PCB0)
SATA: 2x internal SATA II drives
Ethernet: 1x Gigabit (Marvell 88E1116R-NNC1)
LED: 7x (white: Power, white/red: Right SATA Activity, USB Activity, Left SATA Activity)
Key: 3x (Power, Reset, USB Copy/Unmount)
Serial: 5 pin header (RXD,GAP,3.3V,GND,TXD), (115200,8,N,1), 3.3V TTL
USB ports: 1x USB 2.0
Flash instruction:
NOTE: this process uses a serial connection. It will upgrade the bootloader and reset the bootloader environment variables
USB flash stick setup
Format to FAT32 without mbr
Copy these files to USB flash stick: dlink_dns-325-a1-initramfs-uImage dlink_dns-325-a1-squashfs-factory.bin dlink_dns-325-a1-squashfs-sysupgrade.bin u-boot.kwb (from u-boot-dns325 directory)
NAS setup
Connect LAN cable between router and NAS device
Connetc USB flash stick to NAS device
Connect serial to NAS device
Boot from new u-boot and install it
$ kwboot -p -b u-boot.kwb -B115200 -t /dev/ttyUSB0
Power on NAS
After download copleted and booted NAS device with new u-boot stop in bootloader by pressing any key
=> usb start
=> fatload usb 0 0x1000000 /u-boot.kwb
=> nand erase.part u-boot
=> nand write 0x1000000 u-boot ${filesize}
=> reset
Update MAC address in u-boot env
Stop in bootloader by pressing any key
Get your MAC address from label on chassis
=> setenv ethaddr XX:XX:XX:XX:XX:XX
=> saveenv
Install OpenWrt by flashing factory image from u-boot
=> usb start
=> fatload usb 0 0x1000000 /dlink_dns-325-a1-squashfs-factory.bin
=> nand erase.part ubi
=> nand write 0x1000000 ubi ${filesize}
=> reset
Based-on: #9296
Signed-off-by: Konstantin Meshkov <skyline@mail.ru>
[ refresh uboot patches ]
Link: https://github.com/openwrt/openwrt/pull/17924
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
95 lines
1.9 KiB
Plaintext
95 lines
1.9 KiB
Plaintext
#
|
|
# Copyright (C) 2012-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
kirkwood_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
checkpoint,l-50)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
|
|
;;
|
|
cisco,on100)
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
cloudengines,pogoe02|\
|
|
cloudengines,pogoplugv4|\
|
|
ctera,c200-v1|\
|
|
dlink,dns320l|\
|
|
dlink,dns-325-a1|\
|
|
globalscale,sheevaplug|\
|
|
iom,iconnect-1.1|\
|
|
iom,ix2-200|\
|
|
iptime,nas1|\
|
|
netgear,readynas-duo-v2|\
|
|
netgear,stora|\
|
|
raidsonic,ib-nas62x0|\
|
|
seagate,blackarmor-nas220|\
|
|
seagate,dockstar|\
|
|
seagate,goflexhome|\
|
|
seagate,goflexnet|\
|
|
zyxel,nsa310b|\
|
|
zyxel,nsa310s|\
|
|
zyxel,nsa325)
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
endian,4i-edge-200)
|
|
ucidef_set_interface_lan "port1 port2 port3 port4 eth1"
|
|
;;
|
|
iom,ix4-200d)
|
|
ucidef_set_interface_lan "eth0 eth1" "dhcp"
|
|
;;
|
|
linksys,e4200-v2|\
|
|
linksys,ea3500|\
|
|
linksys,ea4500)
|
|
ucidef_set_interfaces_lan_wan "ethernet1 ethernet2 ethernet3 ethernet4" "internet"
|
|
;;
|
|
*)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
kirkwood_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
local label_mac=""
|
|
|
|
case "$board" in
|
|
dlink,dns320l)
|
|
lan_mac=$(mtd_get_mac_text "mini firmware")
|
|
;;
|
|
iptime,nas1)
|
|
lan_mac=$(mtd_get_mac_binary u-boot 0x3ffa8)
|
|
label_mac=$lan_mac
|
|
;;
|
|
linksys,e4200-v2|\
|
|
linksys,ea3500|\
|
|
linksys,ea4500)
|
|
wan_mac=$(mtd_get_mac_ascii u_env eth1addr)
|
|
;;
|
|
zyxel,nsa310b|\
|
|
zyxel,nsa325)
|
|
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
kirkwood_setup_interfaces $board
|
|
kirkwood_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|