9c26d14489
Vimin VM-S100-0800MS is an 8 port Multi-Gig switch, based on RTL9303.
Ported from XikeStor SKS8300-8X with changes to support different u-boot
build.
Specification:
- SoC : Realtek RTL9303
- RAM : DDR3 512 MiB
- Flash : SPI-NOR 16 MiB (Winbond W25Q128JVSQ)
- Ethernet : 8x 1/2.5/10 Gbps (SFP+)
- LEDs/Keys (GPIO): 0x/1x
- UART : "Console" port on the front panel
- type : RS-232C
- connector : RJ-45
- settings : 115200n8
- Power : AC100-240V 50/60Hz
Flash instruction using initramfs image:
1. Prepare TFTP server with an IP address "192.168.1.111"
2. Connect your PC to Port1 on VM-S100-0800MS
3. Power on VM-S100-0800MS and interrupt boot by pressing Esc
4. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
7. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
8. Boot with the downloaded image
bootm
9. On the initramfs image, backup the stock firmware if needed
10. Upload (or download) sysupgrade image to the device
11. Erase "firmware" partition to cleanup JFFS2 of stock FW
mtd erase firmware
12. Perform sysupgrade with the sysupgrade image
13. Wait ~120 sec to complete flashing
Reverting to stock firmware:
1. Prepare by downloading the stock firmware. Vimin doesn't have
the firmware on their website, tested using firmware for shared
hardware Nicgiga S100-0800S-M.
Filename: vmlinux-nicgiga-S100-0800S-M-241126EN.bix
2. Prepare TFTP server with an IP address "192.168.1.111"
3. Connect your PC to Port1 on VM-S100-0800MS
4. Power on VM-S100-0800MS and interrupt boot by pressing Esc
5. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
6. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
7. Boot with the downloaded image
bootm
8. Under Management -> Firmware -> Upgrade/Backup, upload bix file.
9. Reboot device
Signed-off-by: Colton Pawielski <cepawiel@mtu.edu>
Link: https://github.com/openwrt/openwrt/pull/19477
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
89 lines
2.1 KiB
Makefile
89 lines
2.1 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
define Build/xikestor-nosimg
|
|
$(STAGING_DIR_HOST)/bin/nosimg-enc -i $@ -o $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Device/hasivo_s1100w-8xgt-se
|
|
SOC := rtl9303
|
|
DEVICE_VENDOR := Hasivo
|
|
DEVICE_MODEL := S1100W-8XGT-SE
|
|
IMAGE_SIZE := 12288k
|
|
KERNEL_INITRAMFS := \
|
|
kernel-bin | \
|
|
append-dtb | \
|
|
lzma | \
|
|
uImage lzma
|
|
endef
|
|
TARGET_DEVICES += hasivo_s1100w-8xgt-se
|
|
|
|
define Device/tplink_tl-st1008f_v2
|
|
SOC := rtl9303
|
|
UIMAGE_MAGIC := 0x93030000
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_MODEL := TL-ST1008F
|
|
DEVICE_VARIANT := v2.0
|
|
DEVICE_PACKAGES := kmod-gpio-pca953x
|
|
IMAGE_SIZE := 31808k
|
|
endef
|
|
TARGET_DEVICES += tplink_tl-st1008f_v2
|
|
|
|
define Device/vimin_vm-s100-0800ms
|
|
SOC := rtl9303
|
|
UIMAGE_MAGIC := 0x93000000
|
|
DEVICE_VENDOR := Vimin
|
|
DEVICE_MODEL := VM-S100-0800MS
|
|
IMAGE_SIZE := 13312k
|
|
$(Device/kernel-lzma)
|
|
endef
|
|
TARGET_DEVICES += vimin_vm-s100-0800ms
|
|
|
|
define Device/xikestor_sks8300-8x
|
|
SOC := rtl9303
|
|
DEVICE_VENDOR := XikeStor
|
|
DEVICE_MODEL := SKS8300-8X
|
|
DEVICE_ALT0_VENDOR := ONTi
|
|
DEVICE_ALT0_MODEL := ONT-S508CL-8S
|
|
BLOCKSIZE := 64k
|
|
KERNEL_SIZE := 8192k
|
|
IMAGE_SIZE := 30720k
|
|
IMAGE/sysupgrade.bin := pad-extra 256 | append-kernel | xikestor-nosimg | \
|
|
jffs2 nos.img -e 4KiB -x lzma | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-rootfs | pad-rootfs | append-metadata | check-size
|
|
endef
|
|
TARGET_DEVICES += xikestor_sks8300-8x
|
|
|
|
define Device/zyxel_xgs1210-12
|
|
SOC := rtl9302
|
|
UIMAGE_MAGIC := 0x93001210
|
|
ZYXEL_VERS := ABTY
|
|
DEVICE_VENDOR := Zyxel
|
|
DEVICE_MODEL := XGS1210-12
|
|
IMAGE_SIZE := 13312k
|
|
KERNEL_INITRAMFS := \
|
|
kernel-bin | \
|
|
append-dtb | \
|
|
gzip | \
|
|
zyxel-vers | \
|
|
uImage gzip
|
|
endef
|
|
TARGET_DEVICES += zyxel_xgs1210-12
|
|
|
|
define Device/zyxel_xgs1250-12
|
|
SOC := rtl9302
|
|
UIMAGE_MAGIC := 0x93001250
|
|
ZYXEL_VERS := ABWE
|
|
DEVICE_VENDOR := Zyxel
|
|
DEVICE_MODEL := XGS1250-12
|
|
DEVICE_PACKAGES := kmod-hwmon-gpiofan kmod-thermal
|
|
IMAGE_SIZE := 13312k
|
|
KERNEL_INITRAMFS := \
|
|
kernel-bin | \
|
|
append-dtb | \
|
|
gzip | \
|
|
zyxel-vers | \
|
|
uImage gzip
|
|
endef
|
|
TARGET_DEVICES += zyxel_xgs1250-12
|