0c068c6c2f
NN6000v1 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: K4B4G1646E-BCMA 512MiB x2 = 1 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (2x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
NN6000v2 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: MT41K512M16VRN-107 IT:P 1GiB x2 = 2 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (4x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
Install via UART:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Install via Uboot WebUI:
- Only work when you flash a custom uboot with webui
- Push the reset button for 5 seconds, then use broswer to
access http://192.168.1.1/, then upload factory.bin.
Signed-off-by: Fire Chen <firedevel@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/21787
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
124 lines
2.0 KiB
Plaintext
124 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ipq6018-512m.dtsi"
|
|
#include "ipq6018-ess.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &blsp1_uart3;
|
|
led-boot = &led_status_red;
|
|
led-failsafe = &led_status_red;
|
|
led-running = &led_status_green;
|
|
led-upgrade = &led_status_red;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
/* Single RGB led controlled via GPIO.
|
|
To mimic the OEM default behaviour red are switched on from boot */
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_red: status-red {
|
|
gpios = <&tlmm 50 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_RED>;
|
|
function = LED_FUNCTION_STATUS;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_status_green: status-green {
|
|
gpios = <&tlmm 70 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_STATUS;
|
|
};
|
|
|
|
led_status_blue: status-blue {
|
|
gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_STATUS;
|
|
};
|
|
};
|
|
};
|
|
|
|
&tlmm {
|
|
gpio-reserved-ranges = <20 1>;
|
|
|
|
mdio_pins: mdio-pins {
|
|
mdc {
|
|
pins = "gpio64";
|
|
function = "mdc";
|
|
drive-strength = <8>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
mdio {
|
|
pins = "gpio65";
|
|
function = "mdio";
|
|
drive-strength = <8>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp1_uart3 {
|
|
status = "okay";
|
|
pinctrl-0 = <&serial_3_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&qusb_phy_0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ssphy_0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&rpm {
|
|
status = "disabled";
|
|
};
|
|
|
|
&sdhc {
|
|
bus-width = <8>;
|
|
mmc-ddr-1_8v;
|
|
mmc-hs200-1_8v;
|
|
non-removable;
|
|
status = "okay";
|
|
};
|
|
|
|
&wifi {
|
|
status = "okay";
|
|
qcom,ath11k-fw-memory-mode = <1>;
|
|
qcom,ath11k-calibration-variant = "Link-NN6000";
|
|
};
|
|
|
|
&edma {
|
|
status = "okay";
|
|
};
|