c60be6e983
Specifications
--------------
- SoC : Qualcomm IPQ4019
- RAM : 256 MiB DDR3-1600 (NT5CC128M16IP)
- Flash : 32 MiB SPI NOR
- V1, V2 : GigaDevice GD25Q256C
- V3 : Winbond W25Q256FV, Micron N25Q128A11
- V320 : EON EN25QH256, XMC XM25QH256BK (with patch included)
- WLAN : IPQ4019 On-chip
- 2.4 GHz : 2x2 MIMO 802.11b/g/n
- 5 GHz : 2x2 MIMO 802.11n/ac
- Ethernet : QCA8072 10/100/1000BASE-T 1x WAN; 1x LAN
- UART : 3v3 115200n, use pins under heatsink
- Buttons : 1x Reset
- LEDs : 1x Combined RGB LED
- V1 : Driven by LP5521 channels (Channel 0, 1, 2?)
- V3, V320 : Driven by GPIO Pins (Pin 28, 32, 35 Active Low)
- Bluetooth :
- V1, V2, V3 : CSR8811
- V320 : AC6368A/B
- Power : DC 12V @ 1.2A
- FCC ID :
- V1 : TE7M5
- V3 : TE7M5V3
- V320 : TE7M5V32, 2AXJ4M5V3, 2BCGWM5V3
- TFTP ID :
- Client : 192.168.0.66
- Router : 192.168.0.11
MAC Addresses
-------------
Label : OPAQUE partition @ 0x0008
LAN : Label
WAN : Label + 1
WLAN 2G : Label + 2
WLAN 5G : Label + 3
Installation
------------
1. Install TFTP server software
2. Rename the factory image to 'M5v1_tp_recovery.bin' and copy it into
the TFTP folder
3. Connect an interface configured to 192.168.0.66/24 to the LAN port
- Note: The LAN port is the ethernet port that is furthest away from
the power plug
4. Press the 'reset' button down before powering up the device, holding
for at least 10 seconds
5. Router should download the factory image, install it, and then reboot
6. Router will start up with address 192.168.1.1
Known Issues
------------
- Some devices (including some V1 and V2 devices) may have flash chips
that are not detected, supported by, or have broken SFDP support
Signed-off-by: Bee Cadorna <r3usrlnd@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17537
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
|---|---|---|
| .devcontainer/ci-env | ||
| .github | ||
| .vscode | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0