d048137e85
Add a watchdog driver for the external management MCU on Hasivo /
Horaco network switches, reachable over I2C. Without periodic
keepalive the MCU resets the board every ~3 minutes.
The driver arms the MCU at probe and registers a struct
watchdog_device with WDOG_HW_RUNNING so the watchdog core feeds the
chip via a kernel timer until userspace opens the watchdog node.
Timeout is fixed at 15s; the hardware threshold is baked into MCU
firmware and is not software-configurable.
The I2C address is supplied per-board in the device tree via the
`reg` property. The driver does not constrain or probe a specific
address. Known addresses across current Hasivo / Horaco silicon:
- 0x6F: Hasivo S1300WP-8XGT-4S+, Hasivo F5800W-12S+,
Horaco ZX-SW82TS-L2P (default / most common)
- 0x6E: alternate Hasivo / Horaco variant
The driver, its device-tree binding and the Kconfig/Makefile wiring
are added to the kernel tree as a realtek target patch and exposed as
the kmod-hasivo-mcu-wdt KernelPackage. Keeping the binding in the
kernel tree lets dt_binding_check exercise it during the build and
makes the whole driver easy to drop once it lands upstream.
Tested on Hasivo S1300WP-8XGT-4S+ (RTL9313). Unbinding the driver
causes the MCU to power-cycle the board within ~15s.
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Link: https://github.com/openwrt/openwrt/pull/23418
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
|
||
|---|---|---|
| .devcontainer/ci-env | ||
| .github | ||
| .vscode | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0