catspeed-cc/tew-829dru-goldrepo
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Update README.md

Browse Source 
updated wifi identifiers
This commit is contained in:
MooCat 2026-06-14 19:05:57 -04:00 committed by GitHub
parent 3f22c77def
commit 76aa7426c4
Signed by: mooleshacat
GPG Key ID: B5690EEEBB952194
1 changed files with 111 additions and 43 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

154
README.md
View File

@ -34,7 +34,7 @@ I am doing so for a few reasons:
## ORIGINAL SOURCE - UP TO DATE GOLD SHEET: ## ORIGINAL SOURCE - UP TO DATE GOLD SHEET:
``` ```
###################### ######################
## GOLD SHEET ## ## GOLD SHEET ##
###################### ######################
@ -102,7 +102,6 @@ Wireguard performance: ?
############################### ###############################
FCC ID: XU8TEW829DRU FCC ID: XU8TEW829DRU
Board Manufacturer: U-MEDIA Board Manufacturer: U-MEDIA
DevKit: Qualcomm IPQ40xx/AP-DK04.1-C1 (corrected) DevKit: Qualcomm IPQ40xx/AP-DK04.1-C1 (corrected)
@ -112,6 +111,11 @@ DTS Closest Sibling: qcom-ipq4019-ap.dk04.1-c1.dts (corrected)
DTSI File: qcom-ipq4019-ap.dk04.1.dtsi DTSI File: qcom-ipq4019-ap.dk04.1.dtsi
Inherits: qcom-ipq4019.dtsi Inherits: qcom-ipq4019.dtsi
QCA9984 firmware identifier: bus=pci,bmi-chip-id=0,bmi-board-id=1
QCA4019 firmware identifier: bus=ahb,bmi-chip-id=0,bmi-board-id=28,variant=TEW-829DRU-2G
bus=ahb,bmi-chip-id=0,bmi-board-id=30,variant=TEW-829DRU-5G
########### ###########
## NOTES ## ## NOTES ##
@ -164,9 +168,9 @@ Note: GPIO's on this device are offset by +512 - logical GPIO1 is actually GPIO5
Note: Working on obtaining LED & switch/phy reset GPIO's Note: Working on obtaining LED & switch/phy reset GPIO's
Note: TRENDnet does not provide GPIO mappings - failing to comply w/ GPL & provide proper CCS Note: TRENDnet does not provide GPIO mappings - failing to comply w/ GPL & provide proper CCS
GPIO FUNCTION LOGICAL GPIO ACTUAL GPIO FUNCTION
48 usb-power-enable -> drive HIGH to enable USB power (finally found it via probing!) 48 560 usb-power-enable -> drive HIGH to enable USB power (finally found it via probing!)
############# #############
@ -407,6 +411,22 @@ DECIMAL HEXADECIMAL DESCRIPTION
root@AIKS0:~/work/flash-dump# root@AIKS0:~/work/flash-dump#
######################################
## Micron MT29F1G08ABADA NAND 128MB ##
## PARTITION TABLE DUMP ##
######################################
group_pairs Layout blocks found at PEBs: [[0, 1], [384, 385], [801, 921]]
description Create Volume: b'kernel', ID: 0, Block Cnt: 29
description Create Volume: b'ubi_rootfs', ID: 1, Block Cnt: 162
description Created Image: 1119963279, Volume Cnt: 2
description Create Volume: b'kernel', ID: 0, Block Cnt: 30
description Create Volume: b'ubi_rootfs', ID: 1, Block Cnt: 162
description Created Image: 490764789, Volume Cnt: 2
description Create Volume: b'rootfs_data', ID: 0, Block Cnt: 39
description Created Image: 864603106, Volume Cnt: 1
# FROM GPL SOURCE: # FROM GPL SOURCE:
root@AIKS0:~/work/GPL_SOURCE/GPL_TEW-829DRU_v1/IPQ4019.ILQ.1.2# cat common/build/ipq/nand-flash.conf root@AIKS0:~/work/GPL_SOURCE/GPL_TEW-829DRU_v1/IPQ4019.ILQ.1.2# cat common/build/ipq/nand-flash.conf
@ -490,22 +510,6 @@ filename = openwrt-ipq806x-ipq40xx-ubi-root.img
root@AIKS0:~/work/GPL_SOURCE/GPL_TEW-829DRU_v1/IPQ4019.ILQ.1.2# root@AIKS0:~/work/GPL_SOURCE/GPL_TEW-829DRU_v1/IPQ4019.ILQ.1.2#
######################################
## Micron MT29F1G08ABADA NAND 128MB ##
## PARTITION TABLE DUMP ##
######################################
group_pairs Layout blocks found at PEBs: [[0, 1], [384, 385], [801, 921]]
description Create Volume: b'kernel', ID: 0, Block Cnt: 29
description Create Volume: b'ubi_rootfs', ID: 1, Block Cnt: 162
description Created Image: 1119963279, Volume Cnt: 2
description Create Volume: b'kernel', ID: 0, Block Cnt: 30
description Create Volume: b'ubi_rootfs', ID: 1, Block Cnt: 162
description Created Image: 490764789, Volume Cnt: 2
description Create Volume: b'rootfs_data', ID: 0, Block Cnt: 39
description Created Image: 864603106, Volume Cnt: 1
################### ###################
## DMESG on BOOT ## ## DMESG on BOOT ##
################### ###################
@ -615,33 +619,33 @@ No size specified -> Using max size (3809280)
## Booting kernel from FIT Image at 84000000 ... ## Booting kernel from FIT Image at 84000000 ...
Using 'config@ap.dk07.1-c1' configuration Using 'config@ap.dk07.1-c1' configuration
Trying 'kernel@1' kernel subimage Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-3.14.43 Description: ARM OpenWrt Linux-3.14.43
Type: Kernel Image Type: Kernel Image
Compression: gzip compressed Compression: gzip compressed
Data Start: 0x840000e4 Data Start: 0x840000e4
Data Size: 3361261 Bytes = 3.2 MiB Data Size: 3361261 Bytes = 3.2 MiB
Architecture: ARM Architecture: ARM
OS: Linux OS: Linux
Load Address: 0x80208000 Load Address: 0x80208000
Entry Point: 0x80208000 Entry Point: 0x80208000
Hash algo: crc32 Hash algo: crc32
Hash value: 455baf05 Hash value: 455baf05
Hash algo: sha1 Hash algo: sha1
Hash value: 815ee16957306915e27edd00aa3f66ef979b805b Hash value: 815ee16957306915e27edd00aa3f66ef979b805b
Verifying Hash Integrity ... crc32+ sha1+ OK Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000 ## Flattened Device Tree from FIT Image at 84000000
Using 'config@ap.dk07.1-c1' configuration Using 'config@ap.dk07.1-c1' configuration
Trying 'fdt@ap.dk07.1-c1' FDT blob subimage Trying 'fdt@ap.dk07.1-c1' FDT blob subimage
Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob
Type: Flat Device Tree Type: Flat Device Tree
Compression: uncompressed Compression: uncompressed
Data Start: 0x8436c2f8 Data Start: 0x8436c2f8
Data Size: 37922 Bytes = 37 KiB Data Size: 37922 Bytes = 37 KiB
Architecture: ARM Architecture: ARM
Hash algo: crc32 Hash algo: crc32
Hash value: b448c7b5 Hash value: b448c7b5
Hash algo: sha1 Hash algo: sha1
Hash value: c2130265a9512115b7a12df0207d3b0f268068f2 Hash value: c2130265a9512115b7a12df0207d3b0f268068f2
Verifying Hash Integrity ... crc32+ sha1+ OK Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8436c2f8 Booting using the fdt blob at 0x8436c2f8
Uncompressing Kernel Image ... OK Uncompressing Kernel Image ... OK
@ -652,4 +656,68 @@ eth2 MAC Address from ART: 3c:8c:f8:f3:96:b3
Using machid 0x8010006 from environment Using machid 0x8010006 from environment
Starting kernel ... Starting kernel ...
#####################
## CALDATA PACKING ##
#####################
These are the board-2.json files I used (named differently)
This is only required for developers porting devices, the average user will not have to do any of this process.
This is mainly documentation for myself.
What is important here is the overall structure, and the `names` field. Copy it exactly.
The filenames are irrelevant. Yours may be different. Just rename or replace them.
qca4019-artcaldata.json
###
[
{
"names": ["bus=ahb,bmi-chip-id=0,bmi-board-id=28,variant=TEW-829DRU-2G"],
"data": "cal-ahb-0-fresh.bin"
},
{
"names": ["bus=ahb,bmi-chip-id=0,bmi-board-id=30,variant=TEW-829DRU-5G"],
"data": "cal-ahb-1-fresh.bin"
}
]
###
qca9984-artcaldata.json
###
[
{
"names": [
"bus=pci,bmi-chip-id=0,bmi-board-id=1"
],
"data": "cal-pci-fresh.bin"
}
]
###
The commands to run to build the bin file:
###
# CREATE BOARD-2.BIN (QCA9984)
qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -c qca9984-artcaldata.json -o qca9984-artcaldata.bin
qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -c qca9984-boardData.json -o qca9984-boardData.bin
# EXTRACT BOARD-2.BIN - INSIDE tmp/ (QCA9984)
qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -e ../../qca9984-artcaldata.bin
qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -e ../../qca9984-boardData.bin
# CREATE BOARD-2.BINS (QCA4019)
qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -c qca4019-artcaldata.json -o qca4019-artcaldata.bin
tools/qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -c qca4019-boardData.json -o qca4019-boardData.bin
# EXTRACT BOARD-2.BIN - INSIDE tmp/ (QCA4019)
qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -e ../qca4019-artcaldata.bin
qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder -e ../qca4019-boardData.bin
###
You can make a tmp/ directory, enter it, and run the extraction command in order to extract it back into a board-2.json and the original bin file(s)
Should the JSON look correct (has both entries if there are two) and there are all bin files present (with different names is ok) then you completed a "round trip".
The files are ready for insertion into your dev environment and built into the image.
``` ```