mediatek: filogic: Add support for Wavlink WL-WN551X3
Hardware -------- - SOC: MediaTek MT7981B - RAM: 256MB DDR3 - FLASH: 128MB SPI-NAND WinBond W25N01GVZEIG - NETWORK: 2x1Gb Lan 1x1Gb Wan - WIFI: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5) - LEDs: 3x WAN/LAN (green) 2x STATUS (red/blue) - USB: 1x XHCI Installation via Webinterface ----------------------------- 1. Rename OpenWrt sysupgrade bin to wavlink_wl-wn551X3-squashfs-sysupgrade.bin The uppercase chars 551X3 are essential and checked by web interface. 2. Logon to webinterface 3. Go to network configuration -> mode selection 4. Choose mode "LAN bridge/access point" 5. Save configuration (maybe network reconfig needed) 6. Go to system upgrade 7. Choose local upgrade and provide renamed sysupgrade file 8. Start upgrade and wait for completion 9. Logon to OpenWrt (network config is preserved during upgrade) Boot initramfs via TFTP & console --------------------------------- 1. Connect switch to network via LAN1 or LAN2 2. Power on switch 3. Press ESC until prompt reached "MT7981>" 4. Set own IP "setenv ipaddr 192.168.x.y" 5. Set TFTP IP "setenv serverip 192.168.a.b" 6. Set memory address "setenv loadaddr 0x46000000" 7. Download image "tftpboot openwrt-mediatek-filogic-wavlink_wl-wn551x3-initramfs.itb" 8. Boot image "bootm" Notes ----- - The red/blue LEDs give a background illumination to the top of the case. The red LED is totally disabled to avoid noisy blinking. - Aside from the design and the different LED colors & placements the hardware and partitioning matches the WAVLINK WL-WN586X3 Rev B. Therefor a common DTSI was prepared. MAC Addresses (same as stock) ----------------------------- LAN : 80:3F:5D:xx:xx:B1 (hw, 0x44e(text)) WAN : 80:3F:5D:xx:xx:B2 (hw, 0x460(text)) 2.4GHz: 80:3F:5D:xx:xx:B1 (Factory, 0x4 (hex)) 5GHz : driver auto generated Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/19515 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Markus Stockhausen
Hauke Mehrtens
parent
56b083221f
commit
1a235a7f0b
@ -0,0 +1,210 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7981b.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up = <103>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down = <103>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bl2";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
reg = <0x4 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "fip";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0x4000000>;
|
||||
};
|
||||
|
||||
partition@4580000 {
|
||||
label = "hw";
|
||||
reg = <0x4580000 0x80000>;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_hw_44e: macaddr@44e {
|
||||
compatible = "mac-base";
|
||||
reg = <0x44e 0x11>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_hw_44e 0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_hw_44e 1>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch: switch@1f {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
nvmem-cells = <&eeprom_factory 0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
};
|
||||
63
target/linux/mediatek/dts/mt7981b-wavlink-wl-wn551x3.dts
Normal file
63
target/linux/mediatek/dts/mt7981b-wavlink-wl-wn551x3.dts
Normal file
@ -0,0 +1,63 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7981b-wavlink-wl-3port-128nand-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "WAVLINK WL-WN551X3";
|
||||
compatible = "wavlink,wl-wn551x3", "mediatek,mt7981b";
|
||||
|
||||
aliases {
|
||||
label-mac-device = &wifi;
|
||||
led-boot = &led_status_blue;
|
||||
led-failsafe = &led_status_blue;
|
||||
led-running = &led_status_blue;
|
||||
led-upgrade = &led_status_blue;
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_blue: led-0 {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-1 {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&pio 8 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
led-2 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
function-enumerator = <1>;
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-3 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
function-enumerator = <2>;
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-4 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
gpios = <&pio 25 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "okay";
|
||||
};
|
||||
@ -206,6 +206,11 @@ tplink,re6000xd)
|
||||
ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-1" "lan2" "link tx rx"
|
||||
ucidef_set_led_netdev "eth1" "lan-3" "blue:lan-2" "eth1" "link tx rx"
|
||||
;;
|
||||
wavlink,wl-wn551x3)
|
||||
ucidef_set_led_netdev "lan-1" "lan-1" "green:lan-1" "lan1" "link tx rx"
|
||||
ucidef_set_led_netdev "lan-2" "lan-2" "green:lan-2" "lan2" "link tx rx"
|
||||
ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx"
|
||||
;;
|
||||
wavlink,wl-wn586x3)
|
||||
ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx"
|
||||
ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx"
|
||||
|
||||
@ -139,6 +139,7 @@ mediatek_setup_interfaces()
|
||||
ucidef_set_interfaces_lan_wan "port1 port3 port4 port5 port6" "port2"
|
||||
;;
|
||||
tplink,tl-xdr6086|\
|
||||
wavlink,wl-wn551x3|\
|
||||
wavlink,wl-wn586x3)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
|
||||
;;
|
||||
|
||||
@ -1972,6 +1972,24 @@ define Device/unielec_u7981-01-nand
|
||||
endef
|
||||
TARGET_DEVICES += unielec_u7981-01-nand
|
||||
|
||||
define Device/wavlink_wl-wn551x3
|
||||
DEVICE_VENDOR := WAVLINK
|
||||
DEVICE_MODEL := WL-WN551X3
|
||||
DEVICE_DTS := mt7981b-wavlink-wl-wn551x3
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_DTS_LOADADDR := 0x47000000
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
KERNEL_INITRAMFS_SUFFIX := .itb
|
||||
KERNEL_IN_UBI := 1
|
||||
DEVICE_PACKAGES := kmod-usb3 kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
|
||||
SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += wavlink_wl-wn551x3
|
||||
|
||||
define Device/wavlink_wl-wn586x3
|
||||
DEVICE_VENDOR := WAVLINK
|
||||
DEVICE_MODEL := WL-WN586X3
|
||||
|
||||
Loading…
Reference in New Issue
Block a user