The DFI ADN553 is a 3.5" SBC based on Intel Atom Alder Lake-N
processors with three Intel I226V 2.5GbE ports.
Specs:
* CPU: Intel Atom x7425E (4C, 12W) / x7213E (2C, 10W) /
x7211E (2C, 6W)
* RAM: 1x DDR5 SO-DIMM, up to 16GB
* Storage: 1x M.2 M key 2242/2280 (PCIe Gen3 x1/SATA3),
1x SATA 3.0
* Ethernet: 3x 2.5GbE RJ-45 (Intel I226V)
* USB: 4x USB 3.2 (rear), 2x USB 2.0 (internal)
* Expansion: 1x M.2 B key 3052 (USB3/USB2, opt. PCIe x1, SIM),
1x M.2 E key 2230 (USB/PCIe x1, CNVi)
* Display: 1x HDMI, 1x Type-C DP Alt. Mode, 1x LVDS/eDP
* Power: 9-36V DC wide range input
* TPM: dTPM 2.0 (NPCT750AADYX)
* Form factor: 3.5" SBC (146mm x 102mm)
Installation:
1. Write the combined-efi.img to a USB drive:
dd if=combined-efi.img of=/dev/sdX conv=fdatasync
2. Boot the ADN553 from the USB drive via the UEFI boot menu.
3. For permanent installation, write the image to the M.2 or
SATA storage device.
The board uses "Default string" as DMI sys_vendor and product_name
placeholders, so board detection is fixed by filtering these out and
falling through to board_vendor (DFI Inc.) and board_name (ADN553).
The three I226V NICs are pinned to their PCIe paths to ensure
consistent interface ordering matching the physical left-to-right
port layout. eth0 is assigned as WAN and eth1/eth2 as LAN.
Link: https://github.com/openwrt/openwrt/pull/22980
(cherry picked from commit b6b09a2ad8)
Link: https://github.com/openwrt/openwrt/pull/23015
Signed-off-by: Nick Hainke <vincent@systemli.org>
This device has a redundant configuration. Important when writing to it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22882
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is apparently a redundant u-boot config split between cfg1 and
cfg2. The size is also 0x10000 instead of the full amount.
This is needed in order to fix ethernet probing.
Fixes: 3faa3a04bb ("ath79: enterasys,ws-ap3805i: use nvmem")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22882
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit b4d7263bc3 ("kernel: of: avoid some unnecessary bad cell count
warnings") backported Linux commit 6e5773d52f4a ("of/address: Fix WARN
when attempting translating non-translatable addresses"), which started
requiring #address-cells for a device's parent if we want to use the
reg resource in a device node.
Many Chromium devices use a /firmware/coreboot device node that is
patched in by the boot firmware. These structures look something like:
# find /sys/firmware/devicetree/base/firmware/
/sys/firmware/devicetree/base/firmware/
/sys/firmware/devicetree/base/firmware/scm
/sys/firmware/devicetree/base/firmware/scm/compatible
/sys/firmware/devicetree/base/firmware/scm/name
/sys/firmware/devicetree/base/firmware/ranges
/sys/firmware/devicetree/base/firmware/chromeos
/sys/firmware/devicetree/base/firmware/chromeos/fmap-offset
/sys/firmware/devicetree/base/firmware/chromeos/compatible
/sys/firmware/devicetree/base/firmware/chromeos/readonly-firmware-version
/sys/firmware/devicetree/base/firmware/chromeos/nonvolatile-context-storage
/sys/firmware/devicetree/base/firmware/chromeos/hardware-id
/sys/firmware/devicetree/base/firmware/chromeos/firmware-type
/sys/firmware/devicetree/base/firmware/chromeos/vboot-shared-data
/sys/firmware/devicetree/base/firmware/chromeos/nonvolatile-context-offset
/sys/firmware/devicetree/base/firmware/chromeos/firmware-version
/sys/firmware/devicetree/base/firmware/chromeos/nonvolatile-context-size
/sys/firmware/devicetree/base/firmware/chromeos/name
/sys/firmware/devicetree/base/firmware/coreboot
/sys/firmware/devicetree/base/firmware/coreboot/compatible
/sys/firmware/devicetree/base/firmware/coreboot/board-id
/sys/firmware/devicetree/base/firmware/coreboot/reg
/sys/firmware/devicetree/base/firmware/coreboot/name
/sys/firmware/devicetree/base/firmware/name
Notably, there is no #{address,size}-cells in /firmware.
This breaks any driver relying on a device under /firmware, such as the
coreboot_table driver.
This is technically an ill-formatted FDT, and so we might as well just
add the properties ourselves.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22951
(cherry picked from commit a94c020f38)
Link: https://github.com/openwrt/openwrt/pull/22957
Signed-off-by: Robert Marko <robimarko@gmail.com>
commit eaa82118ea missed kmod change for clearfog base/pro
Fixes: eaa82118ea ("mvebu: Switch to use a module for mv88e6xxx")
Signed-off-by: Sven Friedmann <sf.github@okay.ms>
Link: https://github.com/openwrt/openwrt/pull/22918
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 92259bcf1e)
The check of files from packages was only checking opkg files.
Check for apk as well and fail if both are missing.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17847
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 37c5aade23)
The list of files excluded from backup was outdated.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17847
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2c146f29e8)
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB NOR
- RAM: 64 MiB DDR2
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN/LAN, 1x 10/100 LAN (MT7628)
- Build-in LTE Modem: MeigLink SLM770A
4G Cat. 4 (150/50 Mbps)
- Buttons: 1x Reset, 1x wps
- LEDs: Front: 1x Red, 1x White,
Back: 3x White 4G signal strengh
- Serial console: unpopulated header, 115200 8n1
- Power: USB-C
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Migration to OpenWrt:
- Download the RSA signed intermediate firmware from the Cudy website:
`openwrt-ramips-mt76x8-cudy_lt300-v3-squashfs-flash.bin`
- Connect computer to LAN and flash the intermediate firmware via OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21982
(cherry picked from commit b4a5e57bde)
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some Banana Pi BPI-R4 BE14 WiFi modules are shipped with zeroed
tx_power fields in EEPROM (2G/5G/6G). This leads to low transmit power
on affected bands.
This overlay provides known-good EEPROM data (including correct tx_power
values for 2G/5G/6G bands) dumped from a working BE14 module.
To enable BE14 overlay, add into u-boot bootconf_extra
parameter: 'mt7988a-bananapi-bpi-r4-wifi-be14'.
You can use example script:
overlay="mt7988a-bananapi-bpi-r4-wifi-be14"
current="$(fw_printenv -n bootconf_extra 2>/dev/null)"
if [ -n "${current}" ]; then
fw_setenv bootconf_extra "${current}#${overlay}"
else
fw_setenv bootconf_extra "${overlay}"
fi
Earlier proposal proposed in [1] was fallback to default values if
invalid EEPROM content is detected.
[1] https://github.com/openwrt/openwrt/pull/19503/
Fixes: https://github.com/openwrt/openwrt/issues/17489
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
(cherry picked from commit 561e3cf678)
Link: https://github.com/openwrt/openwrt/pull/22842
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Huasifei WH3000 Pro NAND version.
There is an eMMC already supported in OpenWrt. The only difference is NAND chip.
This commit adds common .dtsi and separate .dts
for eMMC and nand versions.
**Huasifei WH3000 Pro NAND**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: 256mb Winbond SPI NAND
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
M.2 (WWAN) slot
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-nand-squashfs-sysupgrade.bin
```
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22694
(cherry picked from commit f4c211f635)
Link: https://github.com/openwrt/openwrt/pull/22819
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These patches stop secondary CPUs before restart and wait for them
to go offline, fixing the mt7621 reboot deadlock without needing to
disable CONFIG_LIST_HARDENED.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/22724
(cherry picked from commit 3166710fc9)
Link: https://github.com/openwrt/openwrt/pull/22673
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Initialize NPU Block Ack memory region if reserved via DTS.
Block Ack memory region is used by NPU MT7996 (Eagle) offloading.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/22289
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 305f685f83)
Link: https://github.com/openwrt/openwrt/pull/22372
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce the capability to read the firmware binary names from device-tree
using the firmware-name property if available.
This is a preliminary patch to enable NPU offloading for MT7996 (Eagle)
chipset since it requires a different binary with respect to the one
used for MT7992 on the EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/22289
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 123557f0e2)
Link: https://github.com/openwrt/openwrt/pull/22372
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The GitHub CI was sometimes still building some tools again even when
the same version was already pre-built. This change fixes the problem
and should improve the speed of the GitHub CI actions. The duration of
the "Build tools" step will be reduced from 5 to 20 minutes down to
10 to 15 seconds.
make also checks that dependencies are not more recent than the target
it wants to build. Previously find returned files in an arbitrary order
and touch set the current timestamp. Since touch is called per file the
timestamps differ in fractional seconds, so not all files got the same
time. make detected a more recent dependency and started to rebuild.
Now all files are set to the same timestamp and make will assume
everything is up to date.
It is sufficient to only touch the stamp files to prevent rebuilding.
Link: https://github.com/openwrt/openwrt/pull/22888
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cd6cb9f765)
Without this, max_oper_chwidth is set incorrectly,
thus ibss_mesh_select_80_160mhz fails to set the correct channel width
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22644
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6abfd98c4e)
This release incorporates the following bug fixes and mitigations:
Fixed incorrect failure handling in RSA KEM RSASVE encapsulation.
(CVE-2026-31790)
Fixed loss of key agreement group tuple structure when the DEFAULT keyword
is used in the server-side configuration of the key-agreement group list.
(CVE-2026-2673)
Fixed potential use-after-free in DANE client code.
(CVE-2026-28387)
Fixed NULL pointer dereference when processing a delta CRL.
(CVE-2026-28388)
Fixed possible NULL dereference when processing CMS KeyAgreeRecipientInfo.
(CVE-2026-28389)
Fixed possible NULL dereference when processing CMS
KeyTransportRecipientInfo.
(CVE-2026-28390)
Fixed heap buffer overflow in hexadecimal conversion.
(CVE-2026-31789)
No need refresh patches
Signed-off-by: Jack Sun <sunjiazheng321521@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 62ea6aad47)
This version fixes some security problems:
* Client impersonation while resuming a TLS 1.3 session
(CVE-2026-34873)
* Entropy on Linux can fall back to /dev/urandom (CVE-2026-34871)
* PSA random generator cloning (CVE-2026-25835)
* Compiler-induced constant-time violations (CVE-2025-66442)
* Null pointer dereference when setting a distinguished name
(CVE-2026-34874)
* Buffer overflow in FFDH public key export (CVE-2026-34875)
* FFDH: lack of contributory behaviour due to improper input validation
(CVE-2026-34872)
* Signature Algorithm Injection (CVE-2026-25834)
* CCM multipart finish tag-length validation bypass (CVE-2026-34876)
* Risk of insufficient protection of serialized session or context data
leading to potential memory safety issues (CVE-2026-34877)
* Buffer underflow in x509_inet_pton_ipv6() (CVE-2026-25833)
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/mbedtls-3.6.6
Size increases by 470 bytes on aarch64:
343995 bin/packages/aarch64_generic/base/libmbedtls21-3.6.5-r1.apk
344465 bin/packages/aarch64_generic/base/libmbedtls21-3.6.6-r1.apk
Link: https://github.com/openwrt/openwrt/pull/22787
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f48ef0040b)
No need to add another aliases node just for the label-mac-device,
luckily DTC was smart enough to combine them together in the final DTB.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bootloader on this device is old and supports no lzma. So use
lzma-loader to work around this and get the size smaller so that an
image can actuallly be created and flashed. Because of these size
problems, the last usable version of OpenWrt was 23.05.
This UIMAGE_MAGIC seems to be used by other Netgear devices. Add to
avoid
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000000: 0x2705 instead
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22769
(cherry picked from commit 60383c5d6b)
Link: https://github.com/openwrt/openwrt/pull/22867
Signed-off-by: Robert Marko <robimarko@gmail.com>
Stocks args have
console=ttyS0,9600
rootfstype=squashfs
root=31:03
init=/sbin/init
mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),
1024k(vmlinux.gz.uImage),6208k(rootfs),512k(var),
64k(manufacturing-data),64k(ART)
rootfstype=squashfs,jffs2
which is wrong and interferes with OpenWrt. Keep the non default console
parameter to have console working properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22769
(cherry picked from commit 75ebc8e2c2)
Link: https://github.com/openwrt/openwrt/pull/22867
Signed-off-by: Robert Marko <robimarko@gmail.com>
When CONFIG_TARGET_PER_DEVICE_ROOTFS is enabled (as in buildbot builds),
the final per-device rootfs is assembled at root.squashfs+pkg=<hash> rather
than root.squashfs. The gen_netgear_rootfs_node.sh script was always hashing
root.squashfs (the base rootfs without device-specific packages), causing the
size and hash in the FIT node to not match the actual rootfs written to the
UBI volume, resulting in boot failure on buildbot-produced images.
Fix by using the per-device rootfs path when TARGET_PER_DEVICE_ROOTFS is set,
consistent with how include/image.mk handles the same distinction elsewhere.
Fixes: 46ab9f3f1c ("filogic: add support for Netgear EAX17")
Signed-off-by: Jascha Sundaresan <flizarthanon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit bc0a2c933e)
The correct label mac is needed in a downstream project.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Link: https://github.com/openwrt/openwrt/pull/22803
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ucode path generates different erp_domain and fils_cache_id
values than the legacy shell path due to three mismatches:
1. erp_domain md5 input missing trailing newline (echo adds \n)
2. erp_domain output truncated to 4 chars instead of 8 (shell
uses head -c 8)
3. fils_cache_id md5 input missing trailing newline
4. erp_domain missing fallback to mobility_domain
Same bug pattern as mobility_domain fixed in commit b1dc2736db.
Fixes: #21768
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Signed-off-by: Joshua Klinesmith <joshuaklinesmith@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22677
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b178e05d9b)
Export the unique, monotonic DISKSEQ sequence drive number instead of its
major/minor numbers to identify the boot disk and directly match the partition
in export_partdevice with PARTN.
The MINOR blockdevice numbers are not guaranteed sequential across disks, it
can happen that disks enumerate before their partitions are probed, resulting
in interleaved MINOR numbers breaking the partition offset calculation:
major minor #blocks name
259 0 250059096 nvme0n1
259 2 8192 nvme0n1p1
259 3 491520 nvme0n1p2
259 4 239 nvme0n1p128
259 1 250059096 nvme1n1
259 5 250057728 nvme1n1p1
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Link: https://github.com/openwrt/openwrt/pull/18962
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 63d0b5c243)
The board is exactly identical to the ASUS RT-AX52, I've literally not changed a single thing.
Only AX52 is AX1800, PRO is AX3000.
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Use the compiled asus_rt-ax52-pro-initramfs.trx file from the this repo.
Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease.
Browse to http://192.168.50.1 or http://www.asusrouter.com/
If your router is brand new, finish the setup process and log into the Web-UI.
Navigate to Administration → Firmware Upgrade or use this link http://www.asusrouter.com/Advanced_FirmwareUpgrade_Content.asp.
Upload the .trx file to router
Wait for it to reboot
trx image is initramfs version. You must upgrade to squashfs version.
Browse to http://192.168.1.1/cgi-bin/luci/admin/system/flash
Upload asus_rt-ax52-pro-squashfs-sysupgrade.bin and use sysupgrade -n
Wait for it to reboot
SSH to 192.168.1.1 and set a root password, or browse to http://192.168.1.1
-------Revert to stock asus firmware ---------:
1: Download the rt-ax52 firmware from ASUS official website. Save the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52. Set a static ip on the ethernet interface of your PC. (ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the autoboot process by pressing '4' when prompted. $ ubi remove linux
$ ubi remove jffs2
$ ubi remove rootfs
$ ubi remove rootfs_data
$ ubi create linux 0x45fe000
$ reset
then the dut will reboot,interrupt the autoboot process by pressing '2' when prompted. 2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) $: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Signed-off-by: Emre Yavuzalp <emreyavuzalp2@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21905
(cherry picked from commit 776a926c25)
Link: https://github.com/openwrt/openwrt/pull/22720
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream 2b81db8a7f4475e141a8ffd7cc745ed9f15962df introduced several new
symbols. This commit adds them and also applies alphabetical order via
./scripts/kconfig.pl target/linux/generic/config-6.12
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22276
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 68c8042e9b)
Link: https://github.com/openwrt/openwrt/pull/22699
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems the bootloader does not use 115200, which the dtsi file
specifies. Remove it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8d1b2596ee)
Needed so that the WiFi interfaces come up properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52d776ac96)
Users report pll-data is needed for gigabit speeds.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 469c6676b7)
Add support for Airoha EN7581/AN7583 NPU variant firmware present in
linux-firmware. The Airoha EN7581 NPU variant is to support devices
equipped with the MT7996 WiFi chip.
While at it also add an extra new line to follow pattern of double new line to
separate each firmware package.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 57bf713ef7)
Link: https://github.com/openwrt/openwrt/pull/22371
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXqmiX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
(cherry picked from commit e83da3bada)
Link: https://github.com/openwrt/openwrt/pull/22254
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXmbimX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
(cherry picked from commit 764c503a2c)
Link: https://github.com/openwrt/openwrt/pull/22254
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This access point is a ‘friend’ of the T56 supplied by Odido but with DDR3 RAM and with two Ethernet 2.5 (GPY211)
The flash procedure is similar to other Zyxel T56/EX5600/EX5601
If you need backup please use the T56 guide
Please refer to https://openwrt.org/inbox/toh/zyxel/wx5600-t0 for detailed flash informations
Specifications:
SOC: MT7986b
RAM: 512MB
Flash: 512 MB SPI NAND
Ports: 2 LAN 2.5Gbps (GPY211C)
WIFI: MT7976GN + MT7976AN
LED: 3 bicolor LED - 1 monocolor LED
Buttons: Reset and WPS
We can install all with U-boot and mtk_uartboot.
Load Uboot:
```
./mtk_uartboot -a -p ./mt7986-ram-ddr3-bl2.bin -s /dev/ttyUSB0 -f openwrt-mediatek-filogic-zyxel_wx5600-t0-ubootmod-bl31-uboot.fip
```
**WARNING: Please use a GBIT ethernet or force it on system**
**WARNING: Please use only LAN2 port in Uboot**
Press 0 on Bootmenu
```
mtd erase ubi
run ubi_format
bootmenu
```
Load and write BL2 and U-boot:
```
8
7
```
Load and write recovery and production
```
6
5
```
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Co-authored-by: Hal Martin <halmartin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18364
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 09a0462ea8)
Link: https://github.com/openwrt/openwrt/pull/22659
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This access point is a ‘friend’ of the T56 supplied by Odido but with DDR3 RAM and with two Ethernet 2.5 (GPY211)
The flash procedure is similar to other Zyxel T56/EX5600/EX5601
If you need backup please use the T56 guide
Please refer to https://openwrt.org/inbox/toh/zyxel/wx5600-t0 for detailed flash informations
We can install all with U-boot and mtk_uartboot.
Load Uboot:
```
./mtk_uartboot -a -p ./mt7986-ram-ddr3-bl2.bin -s /dev/ttyUSB0 -f openwrt-mediatek-filogic-zyxel_wx5600-t0-ubootmod-bl31-uboot.fip
```
**WARNING: Please use a GBIT ethernet or force it on system**
**WARNING: Please use only LAN2 port in Uboot**
Press 0 on Bootmenu
```
mtd erase ubi
run ubi_format
bootmenu
```
Load and write BL2 and U-boot:
```
8
7
```
Load and write recovery and production
```
6
5
```
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Link: https://github.com/openwrt/openwrt/pull/18364
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1dbb2d55ac)
Link: https://github.com/openwrt/openwrt/pull/22659
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of redifining the DEVICE_PACKAGES, make sure to expand the list
so yafut is excluded by default as well by $(Device/mikrotik_nor)
Fixes: 13fd9a9ce0 ("ath79: remove kmod-ath9k and wpad from Mikrotik RB750r2")
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit dfbaf84650)
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22667
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
