The BPi R4 Lite can boot from microSD, SPI-NAND, SPI-NOR and eMMC.
Build menu-driven U-Boot for each storage option.
Provide options for installation from microSD to SPI-NAND and SPI-NOR,
and from SPI-NAND to eMMC (similar to BPi-R3).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build the (upstream) configuration for the MT7987 reference board, and
enable support for DT-overlay application which will be necessary to
use the image for the MT7987 RFB generated in OpenWrt.
Adapt our downstream patches (generic reset button, rootdisk selection)
for MT7987 to prepare for real-world boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build TF-A for the MediaTek MT7987 SoC family.
Add necessary downstream patches in preparation for the BananaPi R4 Lite,
which connects both flash chips to SPI2 and got broken MMC bus.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
warning print "ath11k c000000.wifi: failed to flush transmit queue 0"
is observed during busy times.
The mac80211 fallback implementation of `flush_sta` does not handle the per STA queues well.
This is fixed by providing a ath11k specific implementation of flush_sta telling the firmware to flush a given station.
The draining of the transmit queues should therefore stop correctly, even if new packets arrive in the mean time.
An upstream ath11k RFC is available at:
https://patchwork.kernel.org/project/linux-wireless/patch/GV1P250MB14333A5BF24623C4753A10E1E8E0A@GV1P250MB1433.EURP250.PROD.OUTLOOK.COM/
The patch was tested on a Xiaomi AX3600.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Tested-by: Florian Maurer <f.maurer@outlook.de>
Co-authored-by: Benjamin Berg <benjamin@sipsolutions.net>
Tested-by: Flole <flole@flole.de>
Link: https://github.com/openwrt/openwrt/pull/20293
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch CMakeLists.txt for cmake 4.x compatibility.
New cmake versions require at least 3.5 as 'cmake_minimum_required'
in CMakeLists.txt. In future 3.10 will be required.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch CMakeLists.txt in selected apps for cmake 4.x compatibility.
New cmake versions require at least 3.5 as 'cmake_minimum_required'
in CMakeLists.txt. In future 3.10 will be required.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch CMakeLists.txt in selected apps for cmake 4.x compatibility.
New cmake versions require at least 3.5 as 'cmake_minimum_required'
in CMakeLists.txt. In future 3.10 will be required.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Edit CMakeLists.txt to fulfill cmake 4.0 requirement that
cmake_minimum_required is now at least 3.5 and in future 3.10.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
d44af6dd8f4e dhcpv6: create struct dhcpv6_lease
4df45c8c3722 dhcpv4: create struct dhcpv4_lease
a6dccae41b60 odhcpd: struct lease -> struct lease_cfg
fc0abb66f122 dhcpv4: use leasetime from a->lease
74eeff193848 router: always use link-local src address for RAs
b9a071b8341f router: Rewrite the ingress MTU to one configured for the interface
1ef9e0e610d5 router: utilize interface ra_mtu for RA
1480c09ee0aa config: clamp ra_mtu to interface MTU, and default ra_mtu to interface MTU
ee4f0df6bd68 netlink: Store interface MTU at link change
d174e25e85a1 github: fix CI apt dependencies
8f393d55a76e odhcpd: more fixes for IID calculations
fc27940fe9...d44af6dd8f
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
b3e1db42b4db odhcp6c: fix safe interval processing to follow RFC 4862
63461f64d4c1 dhcpv6: always include IA_NA and IA_PD in Request message if requested
1051cabb4da3 dhcpv6: fix incorrect IA type being printed in syslog
c5237eabeb5c odhcp6c: prevent RELEASE at shutdown when -k is set
a01b1ff1e50f odhcp6c: fix client exiting if Renew and Rebind fails
4839bf6d0feb odhcp6c: implement RKAP: Reconfiguration Key Authentication Protocol
52a9a847def4 dhcpv6: fix solicit loop when server has no address available
7b1f67c23de6 ubus: implement ubus methods to force a Renew and Release
2b0e8f2d8541 ubus: implement retransmission configuration via ubus
8d89d373f360 odhcp6c: add failure when -E option is used without ubus support enabled
58f3c9eb1163 odhcp6c: add new argument option to disable script call
1048fc4fb622 reconfigure: move all configuration functions to a new file
93f056d3a1f2 reconfigure: implement DHCP reconfiguration
af669fb23cd3 dhcpv6: implement statistics for DHCPv6
3a1a599fecb7 ubus: implement UBus method to get state data immediately
44c50214997d ubus: emit UBus event on DHCP state changes
33b972bc526a ubus: connect to UBus backend
2f609f248faf odhcp6c: implement asynchronous handling for DHCPv6 State
6466314e7f62 odhcp6c: enable Non-Blocking DHCPv6 Socket
1df65f0caf46 dhcpv6: refactor dhcp_request Function
047c63a8156b dhcpv6: add t1 and t2 transmission
1b5f0c402bbf dscp: add option to set dscp value
96017df54d8f dhcpv6: fix wrong retransmission of DHCPv6 Solicit
b929fc8a1cfd odhcp6c: add a simple build script
adc651ffed55 cmake: make libubox mandatory
5182e2b696ef cmake: drop EXT_PREFIX_CLASS
8d052c52e18d cmake: disable pedantic
f2521b296b21 github: fix CI apt dependencies
77e1ae21e6...b3e1db42b4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
If proto 'dhcpv6' is set for an interface, dynamic interfaces are created
for the protocols map, dslite or 464xlat if this netifd protocols are
installed and the interface option is not explicitly set to '0'.
The problem is that this option cannot be configured via LuCI, which means
that the dynamic protocols are started. In my case, that is the '464xlat'
'6in4' protocol. I see the follwing log messages continuously in the log as
I do not have a '464xlat' in my network.
Fri Aug 22 10:36:33 2025 daemon.notice netifd: Interface 'wan6_4' is now down
Fri Aug 22 10:36:33 2025 daemon.notice netifd: Interface 'wan6_4' is setting up now
Fri Aug 22 10:36:36 2025 daemon.notice netifd: Interface 'wan6_4' is now down
Fri Aug 22 10:36:36 2025 daemon.notice netifd: Interface 'wan6_4' is setting up now
To fix this by adding a new option to disable the dynamic interface creation
for '4in6' if needed. The option is named '4in6_dynamic' and is a boolean.
If the new option is 'true' (default) dynamic interfaces are create.
If the new option set to 'false' no dynamic 4in6 interface are created.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The variable definitions are very confusing. Therefore, this commit groups
them together so that the line length is not exceeded.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This allow configuring the MTU of the ds-lite tunnel.
Updates #8190
Signed-off-by: Mateusz Poliwczak <mpoliwczak34@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20606
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows wpa_supplicant to process pending netlink socket messages
first. Without this change, there is a race condition where the newly
created interface processes netlink events from the removal of the
previous interface.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes it possible to have more flexible control over the supplicant
without having to install wpa_cli.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commits d205878ede and 46cf10771a relabeled the supported Zyxel devices
from v1/v2 to A1/B1, but board setup files were overlooked.
Fixes: d205878ede ("rtl838x: rename GS1900 series v1/v2 to A1/B1")
Fixes: 46cf10771a ("rtl839x: rename GS1900 series v1/v2 to A1/B1")
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Link: https://github.com/openwrt/openwrt/pull/20590
Signed-off-by: Robert Marko <robimarko@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 096739a93d.
The new fortify-headers version needs some more work to be usable in
OpenWrt. Revert this to fix the builds again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add compatibility with the new fortify-headers 2.3.3 by
disabling two warnings.
Fixes: 6268692bd2 ("toolchain: fortify-headers: Update to version 2.3.3")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20552
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the following error by backporting upstream update:
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 4e68103c4e ("uboot-rockchip: fix build with swig 4.3.0")
Link: https://github.com/openwrt/openwrt/pull/20538
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With this change, the interface identifier can be configured via LuCI.
Signed-off-by: Peter Meiser <peter.meiser@gmx.com>
Link: https://github.com/openwrt/openwrt/pull/19318
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add pending patch that disable libmagic support as this cause
reproducibility issue due to timing of presence of libmagic library at
times e2fsprogs gets compiled.
The new patch adds control on libmagic inclusion and we add the
--without-libmagic to the configure args by default.
Reported-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant patch for host build as this has been fixed in 1.44.1
but for some reason it wasn't notice with the patch directly refreshed
(with the fix right up)
Fixes: 198172c048 ("package/utils/e2fsprogs: update to 1.44.1")
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
0d0fac30075f dhcpv4: bump problem scenario up to warn
bf6137092346 config: properly set log level from uci
7956f4271b4e dhcpv6: RFC4833 timezones
7000557cd8f6 dhcpv6-ia: respect prefix assigned to interface (>= /64)
e1e60601ffeb odhcpd: improve odhcpd_urandom()
c2eb4b59f107 config: fix erroneous clamp message if clamp value == max
54b9e729b00d dhcpv4: bail earlier on release/decline
417f4b11d352 dhcpv4: don't hardcode options array length
d63fa3c3612c dhcpv4: shrink struct dhcpv4_message
9653b43617e3 dhcpv4: use iovec for forcereconf messages, fix hash
bf41f4edfbe3 dhcpv4: fix padding of iovec message in dhcpv4_handle_msg()
be68f423c528 dhcpv4: some minor cleanups post-iovec
e24a371ef714 dhcpv4: use iovec for forcerenew opts
bd353e891ae6 dhcpv4: use iovec for router and DNS server
b81cfaa7859e dhcpv4: use iovec for DNS search and MTU
578a9289440b dhcpv4: use iovec for netmask/hostname/broadcast
5bafc17b79d8 dhcpv4: use iovec for leasetime/renew/rebind
b63448ffe447 dhcpv4: introduce a reply_opts array
0533eaea0a94 dhcpv4: use iovec for DNR
6329e37d595d dhcpv4: use iovec for NTP
87fee619205d dhcpv4: use iovec for message and serverid
2f97bf0b56de dhcpv4: reorder some more variables in dhcpv4_handle_msg()
18c1b02bdc20 dhcpv4: remove one more variable from dhcpv4_handle_msg()
6fd691ff29cd dhcpv4: move dest handling from dhcpv4_handle_msg()
1f803caf9a1f dhcpv4: don't copy reqopts around
b1be3984ebf8 dhcpv4: more refactoring of dhcpv4_handle_msg()
85717bedf8ce dhcpv4: clarify variable names in dhcpv4_handle_msg()
be864ccf9919 dhcpv4: some more cleanups to dhcpv4_handle_msg()
f87464520564 dhcpv4: preparations for iovec usage
f48e1c205af3 odhcdp: use a more suitable clock
7e78caac4eae dhcpv6: change dhcpv6 message type check in relay
288abd9c4046 dhcpv6: move dhcpv6 message type check for early exit
d504458ef515 odhcpd: add a simple build script
4ee309a54011 github: improve CI
ff3a241ccc98 odhcpd: shrink binary size by creating a logging function
e2ecf7ba6d72 odhcpd: support stderr logging
5de3b0d5b509 odhcpd: add log helpers
398d03a1a236 config: cap dhcpv6_pd_min_len to max instead of only logging error
4f54738d3ae7 config: clamp dhcpv6_hostid_len instead of only logging an error
465f19c9c2e3 config: clamp ra_mtu into 1280-65535 range
434b06133997 config: cap ra_retranstime and warn instead of only logging an error
e5f58a90a147 config: cap ra_hoplimit to maximum and warn instead of logging an error
208eb10307c1 config: cap ra_reachabletime to RFC maximum instead of logging error
93449f1513b4 config: drop double size lease times; they are all UINT32_MAX;
439c0ceab131 router: redefine ra_mininterval and ra_maxinterval as uint32_t
84b4dfe81363 config: clamp ra_mininterval, ra_maxinterval, ra_lifetime at load time
aa4f26232e05 router: refactor calc_ra_lifetime; redefine ra_lifetime as uint32_t
6ece28ffd475 config: do MaxRtrAdvInterval init at (ra_maxinterval) init time
dc03e02d973e router: Apply updated values from RFC9096 (updates RFC4861) to RA/ND
cc7766c12abe router: Apply updated values from RFC8319 (updates RFC4861) to RA/ND
964da13e758c config: refactor parse_leasetime() - branch amount remains same
9646c749467b github: fix CMAKE_SYSTEM_PROCESSOR copy&paste
288206c9a2ed github: add CI build
30780debd691 odhcpd: fix a compilation error
e0b2c3cf9476 odhcpd: allow assignments to be reassigned
01e5e311b0db odhcpd: support multiple per-client DUIDs
aebc647a6b7b odhcpd: support assignments on the basis of IAID
cc3ec9c20c61 odhcpd: support IAIDs for static DHCPv6 leases
e42c62725942 odhcpd: break up complex matching logic
e1123906a4bc odhcpd: document the ubus interface
c69200195263 dhcpv4: generate dbus events on lease expiry
dd7a2d474d0d dhcpv4: fix ubus events
22481d848e0d odhcpd: remove mac_len argument to ubus_bcast_dhcp_event()
d31d64efd56c odhcpd: fix ubus support flag in help msg
9bc1b4e26e10 odhcpd: reduce use of WITH_UBUS defines in code
d402cdae4316 ndp: fix macOS IPv6 compatibility by using link-local source addresses
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
77e1ae21e67f odhcp6c: set server address from Information-request reply
e24ac1cf8c27 dhcpv6: use a per-interface IAID for IA_NA requests
053e6c4b3863 github: improve CI
b65ff293a969 dhcpv6: Check status code for IA_ADDR operations
3c7e425169e1 dhcpv6: Add error checking to handle renew failure for IA_PD operations
8de25373a860 dhcpv6: dhcpv6_parse_ia refactor to switch case
ca3cd525f447 odhcp6c: fix deamon raw buffer inc
d7afeea2b965 dhcpv6c: fix illegal DHCPV6_OPT_FQDN
70f7467db301 script: don't ignore RA with zero router lifetime
6ca1552cb3fe odhcp6c: sync and accumulate RA & DHCPv6 events as fast as possible
29b58cfb4711 odhcp6c: update cmake file
ee6d4a82bbeb github: add CI build
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add IPQ Wifi entry for ath79 TP-Link Archer C60 v2.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Signed-off-by: Robert Marko <robimarko@gmail.com>
Whenever the first bss is removed, any pending scan still keeps a reference
to it. Cancel it in order to prevent use-after-free bugs.
Reported-by: Chad Monroe <chad.monroe@adtran.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
df2f5c9a30f8 veth: delete device before creation to handle stale state
b6d371f30770 system-linux: handle RTM_DELLINK events for device state tracking
777f5942fa7d system-linux: only parse device status for AF_UNSPEC link messages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove earlyprintk from bootargs for arm64 boards.
This option is only valid for arm:
```
Unknown kernel command line parameters "earlyprintk",
will be passed to user space.
```
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Export WiFi 6E (HE) and WiFi 7 (EHT) operation data in scan results.
These additional data can be useful to check wifi channel utilization
by nearby stations.
Example:
Cell 32 - Address: xx:xx:xx:xx:xx:xx
Mode: Master Frequency: 6.115 GHz Band: 6 GHz Channel: 33
Signal: -14 dBm Quality: 70/70
Encryption: SAE (CCMP)
HE Operation:
Center Frequency 1: 39
Center Frequency 2: 47
Channel Width: 160 MHz
EHT Operation:
Center Frequency 1: 47
Center Frequency 2: 63
Channel Width: 320 MHz
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19208
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This includes the following commits from upstream Linux between 6.16 and 6.16.12:
wifi: ath11k: clear initialized flag for deinit-ed srng lists
wifi: ath11k: fix sleeping-in-atomic in ath11k_mac_op_set_bitrate_mask()
wifi: ath11k: fix dest ring-buffer corruption
wifi: ath11k: fix source ring-buffer corruption
wifi: ath11k: fix dest ring-buffer corruption when ring is full
wifi: ath11k: fix group data packet drops during rekey [1]
wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load()
[1] The patch "940-ath11k-Revert-clear-the-keys-properly-when-DISABLE_K.patch" has been removed, as it has been fixed upstream in "wifi: ath11k: fix group data packet drops during rekey" and is added in 945 patch.
Related: https://github.com/openwrt/openwrt/pull/18705
Related: https://github.com/openwrt/openwrt/issues/9555
Related: https://github.com/openwrt/openwrt/issues/14117
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove leading 0 from filename.
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
odhcp6c already supports custom DUIDS on a per-interface basis. When no client
identifier has been set, odhcp6c will generate one on the basis of the MAC
address of the given interface.
This is contrary to how DUIDs are meant to be used, as the client identifier
will vary from interface to interface, while it is meant to remain stable for a
given host, no matter how the network hardware changes (see RFC8415, §11).
Fix this by letting odhcp6c use the global DHCP DUID, if configured.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
This makes the DHCPv4 client use the global DHCP DUID to generate a
RFC4361-style client identifier.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
odhcp6c and odhcpd currently generate custom DUIDS on a per-interface basis
using the MAC address of the given interface.
This is contrary to how DUIDs are meant to be used, as the client identifier
will vary from interface to interface, while it is meant to remain stable for a
given host, no matter how the network hardware changes (see RFC8415, §11).
The same problem exists in odhcpd, which also generates server-side DUIDs on a
per-interface basis.
In order to support a stable per-device DUID, generate one on first boot and
store it via uci.
Currently, a DUID-UUID style clientid is generated. This is mostly meant as an
RFC, and we might consider using a different kind of DUID instead (DUID-LLT,
DUID-EN).
One drawback is that this will typically change the DUID used on existing
OpenWrt devices when upgrading to a new release. However, that seems
unavoidable and is a one-time pain in order to have stable DUIDs (and in many
cases, it shouldn't cause any issues).
v2: move the uci cfg generation outside of an IPv6-only block since this
is relevant to the DHCPv4 client as well
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix package name and AUTOLOAD parameter to match the
actual kernel module name (leds-group-multicolor), enabling proper
auto-loading at boot.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20447
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also implemented the med fast-start -> lldp fast-start change.
lldpd includes a backwards compat handler for the older med command,
but it's better to make these changes so they align with documentation.
Changes:
https://github.com/lldpd/lldpd/releases/tag/1.0.20
Changes:
Enable fast start unconditionally (and move its configuration in "configure lldp")
Make VLAN advertisements configurable
Fix:
Do not break zero-copy traffic on Linux
Fix crash on rapid addition/removal of interfaces
Fix management address selection when pattern is a negative IP address
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20438
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR30H. The MR30H is a POE
powered 802.11ac access point with an integrated 5 port Gigabit switch.
MR30H hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac, QCA9889 802.11/b/g/n/ac scanning radio
* Serial: Internal header (J8, 2.54mm, populated)
LAN5 (rear) is for POE input. LAN4 has POE output (802.3af) when powered
by an 802.3at source.
The LAN4 port is used for tftp booting in U-Boot.
This device does not have secure boot, but cannot be flashed without
external programmers (TSOP48 NAND) as Meraki disabled interrupting U-Boot
for any device that updated after ~2017.
Disassembly:
* Remove the two T10 screws on the rear of the AP.
* Using a guitar pick or similar plastic tool, insert it on the side between
the grey metal plate and the white plastic body and pry up gently.
* The rubberised border on the metal plate does not need to be removed.
* The metal back plate has several latches around the perimeter (but none on
the bottom by the Ethernet ports).
* Once you have removed the metal back plate, push up gently on the bottom
Ethernet ports while pulling gently on the rear-mounted Ethernet port to remove
the PCB.
* The PCB should come free from the plastic housing, pull the bottom
(4 Ethernet ports) up as if you are opening a book.
* If done carefully, there is no need to remove the WiFi antenna connectors
to access the NAND flash.
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
opposite side of the PCB.
* To flash, you need to desolder the TSOP48 or use a 360 clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr30h
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Resolder the NAND after overwriting the `u-boot` regions.
OpenWrt Installation:
* After flashing NAND with the external programmer. Plug an Ethernet
cable into port 4. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Alternative installation steps if your device has U-Boot older than:
`U-Boot 2017.07-RELEASE-g78ed34f31579 (Sep 29 2017 - 07:43:44 -0700)`
**BIG FAT WARNING BEGIN**
Attmping to interrupt boot on a newer U-Boot release may permanently
brick your device! See: riptidewave93/LEDE-MR33#13
**BIG FAT WARNING END**
* Use `ubootwrite.py` from the above GitHub repository to transfer the
`u-boot.itb`
image to the router.
```
./ubootwrite.py --serial=/dev/ttyUSB0 --write u-boot.itb
```
* To avoid bricking your router, it is highly recommended at this point that
you flash the unlocked U-Boot to the `part.safe` ubi volume.
```
run set_ubi && ubi write $loadaddr part.safe 0x2fd48
```
* Power cycle the router. The stock Meraki U-Boot will boot `part.safe` which
is now the unlocked U-Boot.
* Use the new U-Boot build (`" "` to interrupt boot) to
`tftpboot` the OpenWrt initramfs image:
```
dhcp
setenv serverip <tftp_server_addr>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
bootm
```
* It is only recommended to flash U-Boot to the `u-boot` NAND region from
Linux:
```
insmod mtd-rw i_want_a_brick=1
```
* Copy `u-boot.elf` to the router:
```
scp -O u-boot.elf root@192.168.1.1:/tmp/
```
Note: If any of the below commands fails, YOU WILL HAVE A BRICK IF YOU
REBOOT OR LOSE POWER. Only a hardware programmer can recover the device.
```
flash_erase /dev/mtd8 0 0
nandwrite -p /dev/mtd8 /tmp/u-boot.elf
```
Note: ONLY use `u-boot.elf` when flashing the `u-boot` region (`/dev/mtd8`);
`u-boot.bin` or `u-boot.itb` will BRICK YOUR DEVICE
* `scp` the `sysupgrade` image to the device and run the normal `sysupgrade`
procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Z3. The Z3 is a "teleworker"
device with 802.11ac and an integrated 5 port Gigabit switch.
Z3 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x24`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_z3-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubimkvol /dev/ubi0 -N ART -s 524288
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
When lots of events are waiting to be received, the default buffer size
is not enough, and hostapd can run into "No buffer space available" on
recvmsg. This will cause the netdev state tracking to go out of sync.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Previously, devices would have to select `CONFIG_RTL8261N_PHY=Y` in the
whole target's kernel config. Now that this driver is becoming usable
for devices other than Realtek switches, allow packaging this driver
separately.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/20429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the copy_from_user() and copy_to_user() functions for accessing
memory provided by the user in the ptm netdev iotls.
In addition also check for root permission before executing ioctl.
Suggested-by: Stanislav Fort from Aisle Research
Reported-by: Stanislav Fort from Aisle Research
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b462895d3157 lua: CMakeLists: drop redundant cmake_minimum_required
f247c18f8a55 examples: CMakeLists: drop redundant cmake_minimum_required
83a70399030d github: add CI build
d31effb4277b ubusd: Fix out of bounds access in event register message
d95837b1b143 ubusd: acl: compare uid/gid instead of user/group strings
b81257bb20dd ubusd: load extra group IDs for a client process
7d7b45fea05b add debian/ directory
aa4a7ee1d341 ubusd: fix more instances of missing length checks for patterns
60e04048a0e2 ubusd: fix ACL check for receiving events
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Realtek RTL8822CS support to the rtw88 package.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20423
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add IPQ Wifi entry for ath79 TP-Link Archer C59 v1.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix trivial compilation warning caused by downstream full print patch.
../src/app_list.c: In function 'print_full':
../src/app_list.c:85:35: warning: format '%zu' expects argument of type 'size_t', but argument 2 has type 'uint64_t' {aka 'long long unsigned int'} [-Wformat=]
85 | printf("Installed-Size: %zu\n", pkg->installed_size);
| ~~^ ~~~~~~~~~~~~~~~~~~~
| | |
| | uint64_t {aka long long unsigned int}
| unsigned int
| %llu
../src/app_list.c:86:25: warning: format '%zu' expects argument of type 'size_t', but argument 2 has type 'uint64_t' {aka 'long long unsigned int'} [-Wformat=]
86 | printf("Size: %zu\n", pkg->size);
| ~~^ ~~~~~~~~~
| | |
| | uint64_t {aka long long unsigned int}
| unsigned int
| %llu
../src/app_list.c:58:31: warning: unused variable 'd' [-Wunused-variable]
58 | struct apk_dependency d;
Remove unused variable and use PRIu64 to handle uint64_t type.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently wifi-scripts ucode appends airtime_mode to hostapd config file
unconditionally.
However this breaks bringing up interface with hostapd-mini
because the mini variant doesn't support airtime policy.
Fix this by changing the script to append airtime_mode only when
airtime_mode is set to greater than zero value in /etc/config/wireless.
Fixes: #20136Fixes: #20314
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Update the version of uboot-ath79 package to U-Boot v2025.10 release.
Tested on:
- NEC Aterm WG600HP (AR9344)
- NEC Aterm WG1400HP (QCA9558)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20358
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that adding Yuncore AX850 was missed during the board support,
and this breaks buildbots for ipq50xx with:
ERROR: unable to select packages:
ipq-wifi-yuncore_ax850 (no such package):
required by: world[ipq-wifi-yuncore_ax850]
make[4]: *** [/builder/shared-workdir/build/include/image.mk:396: target-dir-90b51871] Error 1
make[4]: *** Waiting for unfinished jobs....
So, add the required meta package.
Fixes: 5d2994a73e ("qualcommax: ipq50xx: Add support for Yuncore AX850")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This was removed by mistake.
Fixes: 292cca0e5c ("uboot-rockchip: Update to 2025.10")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20376
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update package to the latest stable version.
All patches automatically refreshed.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20380
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update package to the latest stable version.
All patches automatically refreshed.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20379
Signed-off-by: Nick Hainke <vincent@systemli.org>
The most relevant change is the removal of the empty board_init()
functions by u-boot/u-boot@70a4d1fa1d, which makes many patches not
apply anymore and also requires most board defconfigs to be updated
by adding "# CONFIG_BOARD_INIT is not set" to them.
Also some config symbols have been renamed and downstream boards
had to be adapted accordingly:
u-boot/u-boot@0fd9a3480a ("env: Rename OVERWRITE_ETHADDR_ONCE to
ENV_OVERWRITE_ETHADDR_ONCE")
u-boot/u-boot@5fb88fa725 ("env: Rename SYS_REDUNDAND_ENVIRONMENT to
ENV_REDUNDANT")
u-boot/u-boot@123682c765 ("env: Rename SYS_RELOC_GD_ENV_ADDR to
ENV_RELOC_GD_ENV_ADDR")
u-boot/u-boot@0f44d5549e ("env: Rename SYS_MMC_ENV_DEV to
ENV_MMC_DEVICE_INDEX")
u-boot/u-boot@31617b880a ("env: Rename SYS_MMC_ENV_PART to
ENV_MMC_EMMC_HW_PARTITION")
u-boot/u-boot@ffc4914703 ("env: Rename ENV_MMC_PARTITION to
ENV_MMC_SW_PARTITION")
u-boot/u-boot@fb5235239a ("env: Rename DEFAULT_ENV_FILE to
ENV_DEFAULT_ENV_TEXT_FILE")
(also renamed USE_DEFAULT_ENV_FILE to USE_ENV_DEFAULT_ENV_TEXT_FILE)
Remove upstreamed patches:
* 001-mtd-spinand-winbond-add-Winbond-W25N04KV-flash-suppo.patch
u-boot/u-boot@fe37fb8214
* 002-mtd-spinand-gigadevice-sync-supported-chips-with-lin.patch
u-boot/u-boot@506ceddffd
* 003-net-mediatek-correct-the-AN8855-TPID-value-in-port-i.patch
u-boot/u-boot@70db2be9fb
* 004-01-serial-mediatek-fix-register-names-and-offsets.patch
u-boot/u-boot@6e15d3f91a
* 004-02-serial-mediatek-enable-baudrate-accuracy-compensatio.patch
u-boot/u-boot@6952209ef2
* 005-clk-mediatek-add-dummy-clk-enable-disable-ops-for-ap.patch
u-boot/u-boot@1bf2121297
* 006-env-Fix-possible-out-of-bound-access-in-env_do_env_s.patch
u-boot/u-boot@0ffd456516
* 130-01-env-mtd-add-the-missing-put_mtd_device.patch
u-boot/u-boot@39ae954b04
* 130-02-env-mtd-initialize-saved_buf-pointer.patch
u-boot/u-boot@7e842bd331
* 170-cmd-bootmenu-permit-to-select-bootmenu-entry-with.patch
u-boot/u-boot@8c986521c3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This series improve network reliability.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch removes dirty hack used to:
* operate with flash
* pass flash page settings to linux driver via SNFI registers
It has been proven that spinand flash page size is actually unnecessary.
We can get all required data from dirmap requests. Thus this patch
series drops the hack and do things properly.
After this fix (and corresponding linux fix) the hack is not needed
anymore.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
Current PKG_MIRROR_HASH is wrong, but it went unnoticed, because the
tarball is being fetched from @OPENWRT project mirrors. Can be
reproduced with:
make package/ppp/{download,check} FIXUP=1 DL_DIR=/tmp PKG_MIRROR_HASH=''
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/20322
Signed-off-by: Robert Marko <robimarko@gmail.com>
Current PKG_MIRROR_HASH is wrong, but it went unnoticed, because the
tarball is being fetched from @OPENWRT project mirrors. Can be
reproduced with:
make package/ebtables/{download,check} FIXUP=1 DL_DIR=/tmp PKG_MIRROR_HASH=''
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/20322
Signed-off-by: Robert Marko <robimarko@gmail.com>
APK, unlike OPKG, can sign individual packages and not just indexes.
Since OpenWrt uses a distributed build infrastructure and only the build
master owns the private keys, signing of individual buildworkers doesn't
work. Right now, each buildworker creates a temporary build key to sign
packages, then transmits the package index to the buildmaster for a
signature.
As a result, all individual packages contain a nonsensical signature,
making them harder to reproduce. This commit removes the individual
package signing.
Since APK requires signatures per default, explicitly allow installation
of unsigned packages during the build process.
The config option here is for historical reasons misleading,
SIGNED_PACKAGES refers to the package index, not the individual
packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The package bump to version rc6 incorporates two recent changes, first, the
stored `mtime` honors SOURCE_DATE_EPOCH, making a prior "touch" obsolete.
Secondly the order of files added to created packages is now sorted, improving
reproducibility, too.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Changelog:
a52bda0 (HEAD, tag: v6.17) bump version to 6.17
c5bfa2a iw: add support to print link level information in station dump
efaf786 iw: Add support to set per-radio RTS threshold in multi-radio wiphy
009ad3b update nl80211.h
aef3798 iw: don't set stupid socket buffer size
8d52fb4 iw: scan: Add partial Multi-Link element printing
cfc0695 iw: print HE mcs correctly when mcs_len
8e4808f iw: Add command to enable/disable EPCS
85b79b3 update nl80211.h
612f9f5 iw: Prevent segfault in ftm get stats
1558e60 iw: print NO-EHT flags for reg get command
59660a3 iw: fix EHT capabilities on Big Endian platforms
8ea80d3 iw: scan: Add printing of EHT Operation Element
7c0511b util: rename hz to Hz vol 2
c2a12a5 util: rename hz to Hz
0cc98ae iw: scan: Decode additional WPA3 group ciphers
f04e5c5 iw: scan: Decode additional WPA3 AKM suite types
41a07a8 iw: fix HE operation on Big Endian platforms
c41971e iw: fix HE capabilities on Big Endian platforms
a6ad3f1 iw: scan: add eht capability parsing
4c85991 iw: util: update and clean up eht capa printing
a0a7dde iw: scan: replace passed ie buffer with ie context
7bc2a84 iw: print tx power per link for MLD
478ddd4 iw: add output for wiphy interface combinations
93e2309 update nl80211.h
966c590 iw: scan: add enum for element IDs
422419e scan: Add printing of HE Operation Element
d088c8a update nl80211.h
73231dd iw: fix formats under MIPS64/PPC
8609336 iw: remove sizer section and related code
c8b9e77 util: clarify comment about 'parsed' pointer
b29da20 iw: add puncturing support
cce9897 iw: refactor frequency help
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20321
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support for color output has existed in iproute2 since forever and we
never compile it out, even in tiny variants. As such, not requiring
people to constantly add -c to their ip commands is a nice QoL feature.
Signed-off-by: George Tsiamasiotis <george@tsiamasiotis.gr>
Link: https://github.com/openwrt/openwrt/pull/20281
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previously we relied on the iproute2 makefile automatically running the
configure script on first run. This does not allow control of some
configure options, or of when the configure script is re-run.
The motivating usecase here is ./configure --color=auto, though that is
not implemented in this commit.
Signed-off-by: George Tsiamasiotis <george@tsiamasiotis.gr>
Link: https://github.com/openwrt/openwrt/pull/20281
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ucidef_set_interface* functions can be used to
add network interfaces to a default network configuration.
Such network interfaces often have the same base interface
name (e.g., eth* or lan*). On devices with many network ports,
adding all ports to the default config can become inconvenient.
This commit adds a new uci function ucidef_set_interface_netdev_range,
which adds network interfaces for a specific port range to a given
OpenWrt interface. The first parameter is the OpenWrt interface, the
second is the base interface name, the third is the port start, and
the fourth is the port end range.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, the interfaces of the Mellanox Spectrum Switch QSFP ports
are all labeled eth*. Their order doesn't match the faceplate and is
different for each model.
They could be named during boot, but this isn't sufficient because they
support port splitting. After such ports are split, their port naming
begins again with eth*, and the same is true after they are unsplit again.
A hotplug script is used here that reads from the sysfs file
phys_port_name, which contains p1, p2, p3, ... for unsplit ports
and p1s0, p1s1, p1s2 for split ports.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the pre-init boot flag for the e1000e network device
driver so that it is loaded during the early pre-init
stage of the boot process instead of later.
Then, it is possible to rename its network ports via the
ucidef_set_network_device_path function from the
02_network script while booting.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is Allwinner's ARM926EJ-S core, which is one of its early
products, reappearing in recent compact designs. The SoC includes
32/64Mb memory in the same physical package, and has display and USB
interfaces, allowing for very small footprint boards.
The target consists of basic 6.12 support, with u-boot. Instead of creating
a separate suniv target, as both the kernel and u-boot supports enough of
this SoC by now with minimal patching, add it into sunxi as a subtarget.
Link: https://github.com/openwrt/openwrt/pull/15022
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
b14cf98 router: log “Sending a RA on lan” at LOG_DEBUG
c2810fe odhcpd: update cmake file
8c2c065 odhcpd: convert README to markdown
3b96480 odhcpd: allow the use of an alternative cfg file
7328bfe odhcpd: remove confusing #defines
cdb9e5b odhcpd: improve RFC9096 § 3.5 SLAAC compliance
RFC9096 § 3.5 SLAAC compliance introduces a new config option (odhcpd
piofolder), which may wear out the flash under certain conditions (for
example: ISPs with dynamic IPv6 prefixes which disconnect the clients
every X hours).
Therefore, setting "dhcp.odhcpd.piofolder" to persistent storage in the
router flash is not advisable and should be set to other kinds of
persistent storage such as USBs, SDs, NVMEs...
In order to prevent wearing out the router flash it's set to ephemeral
storage by default (tmp):
uci set dhcp.odhcpd.piofolder="/tmp/odhcpd-piofolder"
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
272fc1348ea9 lua: CMakeLists: drop redundant cmake_minimum_required
5e69edac2ec4 CMakeLists: fix CMake warning for INCLUDE macro
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Interface might be down or scanning. Better do a full restart in order to avoid
messing up the runtime state.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve the resilence against power failures during
boot-up by trying to sync the file system before
removing the script. The order of the operations
are important.
Signed-off-by: Markus Gothe <markus.gothe@genexis.eu>
Link: https://github.com/openwrt/openwrt/pull/20248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Plasma Cloud PAX1800-Lite is a dual-band Wi-Fi 6 router, based on MediaTek
MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621AT (880 MHz)
- DRAM: DDR3 448 MiB (Nanya NT5CC256M16DP-DI)
- Flash: 2 MiB SPI NOR (S25FL016K) + 128 MB SPI NAND (W25N02KVZEIR)
- Ethernet: 1x 10/100/1000 Mbps (SOC's built-in switch, with PoE+)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: tri-color LED for status (red, blue, green)
- Buttons: 1x (reset)
- Antenna: 4x internal, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, marked as "3V3 G/RX GND W/TX")
- Power: 12 V DC/2 A (DC jack)
MAC addresses:
WAN: 54:9C:27:xx:xx:00 (factory 0x3fff4, device label)
2.4 GHz: 54:9C:27:xx:xx:02 (factory 0x4, device label +2)
5 GHz: 54:9C:27:xx:xx:08 (factory 0xa, device label +8)
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console (115200 8N1) must be used to access the u-boot shell
during bootup. It can then be used to first boot up the initramfs image
from a TFTP server (here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0x83001000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mt76 as support for generic rates power limits in the devicetree. But the
mt7915 supports beamforming and has another table for configuring the
backoff limits. These can be configured in the DT with the paths-*
properties. The path-*-bf are the ones relevant for beamforming and the
ones without -bf suffix for "traditional" path backoff.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The power-limits for ru and mcs and stored in the devicetree as bytewise
array (often with sizes which are not a multiple of 4). These arrays have a
prefix which defines for how many modes a line is applied. This prefix is
also only a byte - but the code still tried to fix the endianness of this
byte with a be32 operation. As result, loading was mostly failing or was
sending completely unexpected values to the firmware.
Since the other rates are also stored in the devicetree as bytewise arrays,
just drop the u32 access + be32_to_cpu conversion and directly access them
as bytes arrays.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
release is Moderate.
This release incorporates the following bug fixes and mitigations:
Fix Out-of-bounds read & write in RFC 3211 KEK Unwrap.
(CVE-2025-9230)
Fix Timing side-channel in SM2 algorithm on 64 bit ARM.
(CVE-2025-9231)
Fix Out-of-bounds read in HTTP client no_proxy handling.
(CVE-2025-9232)
Reverted the synthesised OPENSSL_VERSION_NUMBER change for the release
builds, as it broke some exiting applications that relied on the previous
3.x semantics, as documented in OpenSSL_version(3).
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4b7638925d3e iptime-crc32: add support for ipTIME AX3000M
12c0b42231be nosimg-enc: add new tool for XikeStor SKS8300 series
2051fe5bc2a1 mktplinkfw2: Add 16MLmtk layout
5d1446bf57d6 tplink-safeloader: Add more special_id's for MR70X
075cdc0c4dd4 iptime-crc32: add support for ipTIME AX3000Q
48ababab6b08 iptime-crc32: add support for ipTIME AX3000SM
f29de74ecd7d iptime-crc32: Add device support for ipTIME AX6000M
3346d7711c9a build: add mkqdimg
950f83405a93 iptime-crc32: add support for ipTIME AX7800M-6E
0725c3d4aa1b build: require CMake >= 3.5 due to dropped legacy support
996dc482a7e8 ptgen: fix misprint and simplify calculation a bit
febfef7a09b1 ptgen: use long long instead of long for sizes
6ea8b6dd44d0 ptgen: fix protective MBR partition size
f1f98b0b8456 ptgen: do not create stub partition to fill a gap if gap caused by alignment
3f2d14829150 ptgen: allow non-default placement of gpt entry table
78d8084c7376 ptgen: allow image generation for a specified disk size
9fa340db640e ptgen: create separate images for gpt data structure
d3f8b6ed940a zynsig: add new tool for creating images for the ZyXEL GS1920 series
7e6f69b444c3 npk_pack_kernel: add tool for creating MikroTik NPK kernel packages
0782d243d23e Revert "ptgen: do not create stub partition to fill a gap if gap caused by alignment"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
after change include/package-pack.mk in 16416782f1, must use ALTERNATIVES to create soft link, otherwise the packing will be messed up.
Fixes: openwrt#20270
Fixes: openwrt#20291
Fixes: 16416782f1 (include: make APK packing mtime reproducible)
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20283
Signed-off-by: Robert Marko <robimarko@gmail.com>
d3be5474f6e6 udebug-cli: ignore zero-length messages in logstream
c79f02d899df ucode: fix skipping lines where the timestamp cannot be parsed
5327524e7153 cmake: bump minimum required version to 3.13
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
