Remove earlyprintk from bootargs for arm64 boards.
This option is only valid for arm:
```
Unknown kernel command line parameters "earlyprintk",
will be passed to user space.
```
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Export WiFi 6E (HE) and WiFi 7 (EHT) operation data in scan results.
These additional data can be useful to check wifi channel utilization
by nearby stations.
Example:
Cell 32 - Address: xx:xx:xx:xx:xx:xx
Mode: Master Frequency: 6.115 GHz Band: 6 GHz Channel: 33
Signal: -14 dBm Quality: 70/70
Encryption: SAE (CCMP)
HE Operation:
Center Frequency 1: 39
Center Frequency 2: 47
Channel Width: 160 MHz
EHT Operation:
Center Frequency 1: 47
Center Frequency 2: 63
Channel Width: 320 MHz
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19208
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This includes the following commits from upstream Linux between 6.16 and 6.16.12:
wifi: ath11k: clear initialized flag for deinit-ed srng lists
wifi: ath11k: fix sleeping-in-atomic in ath11k_mac_op_set_bitrate_mask()
wifi: ath11k: fix dest ring-buffer corruption
wifi: ath11k: fix source ring-buffer corruption
wifi: ath11k: fix dest ring-buffer corruption when ring is full
wifi: ath11k: fix group data packet drops during rekey [1]
wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load()
[1] The patch "940-ath11k-Revert-clear-the-keys-properly-when-DISABLE_K.patch" has been removed, as it has been fixed upstream in "wifi: ath11k: fix group data packet drops during rekey" and is added in 945 patch.
Related: https://github.com/openwrt/openwrt/pull/18705
Related: https://github.com/openwrt/openwrt/issues/9555
Related: https://github.com/openwrt/openwrt/issues/14117
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove leading 0 from filename.
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
odhcp6c already supports custom DUIDS on a per-interface basis. When no client
identifier has been set, odhcp6c will generate one on the basis of the MAC
address of the given interface.
This is contrary to how DUIDs are meant to be used, as the client identifier
will vary from interface to interface, while it is meant to remain stable for a
given host, no matter how the network hardware changes (see RFC8415, §11).
Fix this by letting odhcp6c use the global DHCP DUID, if configured.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
This makes the DHCPv4 client use the global DHCP DUID to generate a
RFC4361-style client identifier.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
odhcp6c and odhcpd currently generate custom DUIDS on a per-interface basis
using the MAC address of the given interface.
This is contrary to how DUIDs are meant to be used, as the client identifier
will vary from interface to interface, while it is meant to remain stable for a
given host, no matter how the network hardware changes (see RFC8415, §11).
The same problem exists in odhcpd, which also generates server-side DUIDs on a
per-interface basis.
In order to support a stable per-device DUID, generate one on first boot and
store it via uci.
Currently, a DUID-UUID style clientid is generated. This is mostly meant as an
RFC, and we might consider using a different kind of DUID instead (DUID-LLT,
DUID-EN).
One drawback is that this will typically change the DUID used on existing
OpenWrt devices when upgrading to a new release. However, that seems
unavoidable and is a one-time pain in order to have stable DUIDs (and in many
cases, it shouldn't cause any issues).
v2: move the uci cfg generation outside of an IPv6-only block since this
is relevant to the DHCPv4 client as well
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix package name and AUTOLOAD parameter to match the
actual kernel module name (leds-group-multicolor), enabling proper
auto-loading at boot.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20447
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also implemented the med fast-start -> lldp fast-start change.
lldpd includes a backwards compat handler for the older med command,
but it's better to make these changes so they align with documentation.
Changes:
https://github.com/lldpd/lldpd/releases/tag/1.0.20
Changes:
Enable fast start unconditionally (and move its configuration in "configure lldp")
Make VLAN advertisements configurable
Fix:
Do not break zero-copy traffic on Linux
Fix crash on rapid addition/removal of interfaces
Fix management address selection when pattern is a negative IP address
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20438
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR30H. The MR30H is a POE
powered 802.11ac access point with an integrated 5 port Gigabit switch.
MR30H hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac, QCA9889 802.11/b/g/n/ac scanning radio
* Serial: Internal header (J8, 2.54mm, populated)
LAN5 (rear) is for POE input. LAN4 has POE output (802.3af) when powered
by an 802.3at source.
The LAN4 port is used for tftp booting in U-Boot.
This device does not have secure boot, but cannot be flashed without
external programmers (TSOP48 NAND) as Meraki disabled interrupting U-Boot
for any device that updated after ~2017.
Disassembly:
* Remove the two T10 screws on the rear of the AP.
* Using a guitar pick or similar plastic tool, insert it on the side between
the grey metal plate and the white plastic body and pry up gently.
* The rubberised border on the metal plate does not need to be removed.
* The metal back plate has several latches around the perimeter (but none on
the bottom by the Ethernet ports).
* Once you have removed the metal back plate, push up gently on the bottom
Ethernet ports while pulling gently on the rear-mounted Ethernet port to remove
the PCB.
* The PCB should come free from the plastic housing, pull the bottom
(4 Ethernet ports) up as if you are opening a book.
* If done carefully, there is no need to remove the WiFi antenna connectors
to access the NAND flash.
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
opposite side of the PCB.
* To flash, you need to desolder the TSOP48 or use a 360 clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr30h
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Resolder the NAND after overwriting the `u-boot` regions.
OpenWrt Installation:
* After flashing NAND with the external programmer. Plug an Ethernet
cable into port 4. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Alternative installation steps if your device has U-Boot older than:
`U-Boot 2017.07-RELEASE-g78ed34f31579 (Sep 29 2017 - 07:43:44 -0700)`
**BIG FAT WARNING BEGIN**
Attmping to interrupt boot on a newer U-Boot release may permanently
brick your device! See: riptidewave93/LEDE-MR33#13
**BIG FAT WARNING END**
* Use `ubootwrite.py` from the above GitHub repository to transfer the
`u-boot.itb`
image to the router.
```
./ubootwrite.py --serial=/dev/ttyUSB0 --write u-boot.itb
```
* To avoid bricking your router, it is highly recommended at this point that
you flash the unlocked U-Boot to the `part.safe` ubi volume.
```
run set_ubi && ubi write $loadaddr part.safe 0x2fd48
```
* Power cycle the router. The stock Meraki U-Boot will boot `part.safe` which
is now the unlocked U-Boot.
* Use the new U-Boot build (`" "` to interrupt boot) to
`tftpboot` the OpenWrt initramfs image:
```
dhcp
setenv serverip <tftp_server_addr>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
bootm
```
* It is only recommended to flash U-Boot to the `u-boot` NAND region from
Linux:
```
insmod mtd-rw i_want_a_brick=1
```
* Copy `u-boot.elf` to the router:
```
scp -O u-boot.elf root@192.168.1.1:/tmp/
```
Note: If any of the below commands fails, YOU WILL HAVE A BRICK IF YOU
REBOOT OR LOSE POWER. Only a hardware programmer can recover the device.
```
flash_erase /dev/mtd8 0 0
nandwrite -p /dev/mtd8 /tmp/u-boot.elf
```
Note: ONLY use `u-boot.elf` when flashing the `u-boot` region (`/dev/mtd8`);
`u-boot.bin` or `u-boot.itb` will BRICK YOUR DEVICE
* `scp` the `sysupgrade` image to the device and run the normal `sysupgrade`
procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Z3. The Z3 is a "teleworker"
device with 802.11ac and an integrated 5 port Gigabit switch.
Z3 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x24`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_z3-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubimkvol /dev/ubi0 -N ART -s 524288
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
When lots of events are waiting to be received, the default buffer size
is not enough, and hostapd can run into "No buffer space available" on
recvmsg. This will cause the netdev state tracking to go out of sync.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Previously, devices would have to select `CONFIG_RTL8261N_PHY=Y` in the
whole target's kernel config. Now that this driver is becoming usable
for devices other than Realtek switches, allow packaging this driver
separately.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/20429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the copy_from_user() and copy_to_user() functions for accessing
memory provided by the user in the ptm netdev iotls.
In addition also check for root permission before executing ioctl.
Suggested-by: Stanislav Fort from Aisle Research
Reported-by: Stanislav Fort from Aisle Research
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b462895d3157 lua: CMakeLists: drop redundant cmake_minimum_required
f247c18f8a55 examples: CMakeLists: drop redundant cmake_minimum_required
83a70399030d github: add CI build
d31effb4277b ubusd: Fix out of bounds access in event register message
d95837b1b143 ubusd: acl: compare uid/gid instead of user/group strings
b81257bb20dd ubusd: load extra group IDs for a client process
7d7b45fea05b add debian/ directory
aa4a7ee1d341 ubusd: fix more instances of missing length checks for patterns
60e04048a0e2 ubusd: fix ACL check for receiving events
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Realtek RTL8822CS support to the rtw88 package.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20423
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add IPQ Wifi entry for ath79 TP-Link Archer C59 v1.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix trivial compilation warning caused by downstream full print patch.
../src/app_list.c: In function 'print_full':
../src/app_list.c:85:35: warning: format '%zu' expects argument of type 'size_t', but argument 2 has type 'uint64_t' {aka 'long long unsigned int'} [-Wformat=]
85 | printf("Installed-Size: %zu\n", pkg->installed_size);
| ~~^ ~~~~~~~~~~~~~~~~~~~
| | |
| | uint64_t {aka long long unsigned int}
| unsigned int
| %llu
../src/app_list.c:86:25: warning: format '%zu' expects argument of type 'size_t', but argument 2 has type 'uint64_t' {aka 'long long unsigned int'} [-Wformat=]
86 | printf("Size: %zu\n", pkg->size);
| ~~^ ~~~~~~~~~
| | |
| | uint64_t {aka long long unsigned int}
| unsigned int
| %llu
../src/app_list.c:58:31: warning: unused variable 'd' [-Wunused-variable]
58 | struct apk_dependency d;
Remove unused variable and use PRIu64 to handle uint64_t type.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently wifi-scripts ucode appends airtime_mode to hostapd config file
unconditionally.
However this breaks bringing up interface with hostapd-mini
because the mini variant doesn't support airtime policy.
Fix this by changing the script to append airtime_mode only when
airtime_mode is set to greater than zero value in /etc/config/wireless.
Fixes: #20136Fixes: #20314
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Update the version of uboot-ath79 package to U-Boot v2025.10 release.
Tested on:
- NEC Aterm WG600HP (AR9344)
- NEC Aterm WG1400HP (QCA9558)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20358
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that adding Yuncore AX850 was missed during the board support,
and this breaks buildbots for ipq50xx with:
ERROR: unable to select packages:
ipq-wifi-yuncore_ax850 (no such package):
required by: world[ipq-wifi-yuncore_ax850]
make[4]: *** [/builder/shared-workdir/build/include/image.mk:396: target-dir-90b51871] Error 1
make[4]: *** Waiting for unfinished jobs....
So, add the required meta package.
Fixes: 5d2994a73e ("qualcommax: ipq50xx: Add support for Yuncore AX850")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This was removed by mistake.
Fixes: 292cca0e5c ("uboot-rockchip: Update to 2025.10")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20376
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update package to the latest stable version.
All patches automatically refreshed.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20380
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update package to the latest stable version.
All patches automatically refreshed.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20379
Signed-off-by: Nick Hainke <vincent@systemli.org>
The most relevant change is the removal of the empty board_init()
functions by u-boot/u-boot@70a4d1fa1d, which makes many patches not
apply anymore and also requires most board defconfigs to be updated
by adding "# CONFIG_BOARD_INIT is not set" to them.
Also some config symbols have been renamed and downstream boards
had to be adapted accordingly:
u-boot/u-boot@0fd9a3480a ("env: Rename OVERWRITE_ETHADDR_ONCE to
ENV_OVERWRITE_ETHADDR_ONCE")
u-boot/u-boot@5fb88fa725 ("env: Rename SYS_REDUNDAND_ENVIRONMENT to
ENV_REDUNDANT")
u-boot/u-boot@123682c765 ("env: Rename SYS_RELOC_GD_ENV_ADDR to
ENV_RELOC_GD_ENV_ADDR")
u-boot/u-boot@0f44d5549e ("env: Rename SYS_MMC_ENV_DEV to
ENV_MMC_DEVICE_INDEX")
u-boot/u-boot@31617b880a ("env: Rename SYS_MMC_ENV_PART to
ENV_MMC_EMMC_HW_PARTITION")
u-boot/u-boot@ffc4914703 ("env: Rename ENV_MMC_PARTITION to
ENV_MMC_SW_PARTITION")
u-boot/u-boot@fb5235239a ("env: Rename DEFAULT_ENV_FILE to
ENV_DEFAULT_ENV_TEXT_FILE")
(also renamed USE_DEFAULT_ENV_FILE to USE_ENV_DEFAULT_ENV_TEXT_FILE)
Remove upstreamed patches:
* 001-mtd-spinand-winbond-add-Winbond-W25N04KV-flash-suppo.patch
u-boot/u-boot@fe37fb8214
* 002-mtd-spinand-gigadevice-sync-supported-chips-with-lin.patch
u-boot/u-boot@506ceddffd
* 003-net-mediatek-correct-the-AN8855-TPID-value-in-port-i.patch
u-boot/u-boot@70db2be9fb
* 004-01-serial-mediatek-fix-register-names-and-offsets.patch
u-boot/u-boot@6e15d3f91a
* 004-02-serial-mediatek-enable-baudrate-accuracy-compensatio.patch
u-boot/u-boot@6952209ef2
* 005-clk-mediatek-add-dummy-clk-enable-disable-ops-for-ap.patch
u-boot/u-boot@1bf2121297
* 006-env-Fix-possible-out-of-bound-access-in-env_do_env_s.patch
u-boot/u-boot@0ffd456516
* 130-01-env-mtd-add-the-missing-put_mtd_device.patch
u-boot/u-boot@39ae954b04
* 130-02-env-mtd-initialize-saved_buf-pointer.patch
u-boot/u-boot@7e842bd331
* 170-cmd-bootmenu-permit-to-select-bootmenu-entry-with.patch
u-boot/u-boot@8c986521c3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This series improve network reliability.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch removes dirty hack used to:
* operate with flash
* pass flash page settings to linux driver via SNFI registers
It has been proven that spinand flash page size is actually unnecessary.
We can get all required data from dirmap requests. Thus this patch
series drops the hack and do things properly.
After this fix (and corresponding linux fix) the hack is not needed
anymore.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
Current PKG_MIRROR_HASH is wrong, but it went unnoticed, because the
tarball is being fetched from @OPENWRT project mirrors. Can be
reproduced with:
make package/ppp/{download,check} FIXUP=1 DL_DIR=/tmp PKG_MIRROR_HASH=''
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/20322
Signed-off-by: Robert Marko <robimarko@gmail.com>
Current PKG_MIRROR_HASH is wrong, but it went unnoticed, because the
tarball is being fetched from @OPENWRT project mirrors. Can be
reproduced with:
make package/ebtables/{download,check} FIXUP=1 DL_DIR=/tmp PKG_MIRROR_HASH=''
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/20322
Signed-off-by: Robert Marko <robimarko@gmail.com>
APK, unlike OPKG, can sign individual packages and not just indexes.
Since OpenWrt uses a distributed build infrastructure and only the build
master owns the private keys, signing of individual buildworkers doesn't
work. Right now, each buildworker creates a temporary build key to sign
packages, then transmits the package index to the buildmaster for a
signature.
As a result, all individual packages contain a nonsensical signature,
making them harder to reproduce. This commit removes the individual
package signing.
Since APK requires signatures per default, explicitly allow installation
of unsigned packages during the build process.
The config option here is for historical reasons misleading,
SIGNED_PACKAGES refers to the package index, not the individual
packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The package bump to version rc6 incorporates two recent changes, first, the
stored `mtime` honors SOURCE_DATE_EPOCH, making a prior "touch" obsolete.
Secondly the order of files added to created packages is now sorted, improving
reproducibility, too.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Changelog:
a52bda0 (HEAD, tag: v6.17) bump version to 6.17
c5bfa2a iw: add support to print link level information in station dump
efaf786 iw: Add support to set per-radio RTS threshold in multi-radio wiphy
009ad3b update nl80211.h
aef3798 iw: don't set stupid socket buffer size
8d52fb4 iw: scan: Add partial Multi-Link element printing
cfc0695 iw: print HE mcs correctly when mcs_len
8e4808f iw: Add command to enable/disable EPCS
85b79b3 update nl80211.h
612f9f5 iw: Prevent segfault in ftm get stats
1558e60 iw: print NO-EHT flags for reg get command
59660a3 iw: fix EHT capabilities on Big Endian platforms
8ea80d3 iw: scan: Add printing of EHT Operation Element
7c0511b util: rename hz to Hz vol 2
c2a12a5 util: rename hz to Hz
0cc98ae iw: scan: Decode additional WPA3 group ciphers
f04e5c5 iw: scan: Decode additional WPA3 AKM suite types
41a07a8 iw: fix HE operation on Big Endian platforms
c41971e iw: fix HE capabilities on Big Endian platforms
a6ad3f1 iw: scan: add eht capability parsing
4c85991 iw: util: update and clean up eht capa printing
a0a7dde iw: scan: replace passed ie buffer with ie context
7bc2a84 iw: print tx power per link for MLD
478ddd4 iw: add output for wiphy interface combinations
93e2309 update nl80211.h
966c590 iw: scan: add enum for element IDs
422419e scan: Add printing of HE Operation Element
d088c8a update nl80211.h
73231dd iw: fix formats under MIPS64/PPC
8609336 iw: remove sizer section and related code
c8b9e77 util: clarify comment about 'parsed' pointer
b29da20 iw: add puncturing support
cce9897 iw: refactor frequency help
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20321
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support for color output has existed in iproute2 since forever and we
never compile it out, even in tiny variants. As such, not requiring
people to constantly add -c to their ip commands is a nice QoL feature.
Signed-off-by: George Tsiamasiotis <george@tsiamasiotis.gr>
Link: https://github.com/openwrt/openwrt/pull/20281
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previously we relied on the iproute2 makefile automatically running the
configure script on first run. This does not allow control of some
configure options, or of when the configure script is re-run.
The motivating usecase here is ./configure --color=auto, though that is
not implemented in this commit.
Signed-off-by: George Tsiamasiotis <george@tsiamasiotis.gr>
Link: https://github.com/openwrt/openwrt/pull/20281
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ucidef_set_interface* functions can be used to
add network interfaces to a default network configuration.
Such network interfaces often have the same base interface
name (e.g., eth* or lan*). On devices with many network ports,
adding all ports to the default config can become inconvenient.
This commit adds a new uci function ucidef_set_interface_netdev_range,
which adds network interfaces for a specific port range to a given
OpenWrt interface. The first parameter is the OpenWrt interface, the
second is the base interface name, the third is the port start, and
the fourth is the port end range.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, the interfaces of the Mellanox Spectrum Switch QSFP ports
are all labeled eth*. Their order doesn't match the faceplate and is
different for each model.
They could be named during boot, but this isn't sufficient because they
support port splitting. After such ports are split, their port naming
begins again with eth*, and the same is true after they are unsplit again.
A hotplug script is used here that reads from the sysfs file
phys_port_name, which contains p1, p2, p3, ... for unsplit ports
and p1s0, p1s1, p1s2 for split ports.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the pre-init boot flag for the e1000e network device
driver so that it is loaded during the early pre-init
stage of the boot process instead of later.
Then, it is possible to rename its network ports via the
ucidef_set_network_device_path function from the
02_network script while booting.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is Allwinner's ARM926EJ-S core, which is one of its early
products, reappearing in recent compact designs. The SoC includes
32/64Mb memory in the same physical package, and has display and USB
interfaces, allowing for very small footprint boards.
The target consists of basic 6.12 support, with u-boot. Instead of creating
a separate suniv target, as both the kernel and u-boot supports enough of
this SoC by now with minimal patching, add it into sunxi as a subtarget.
Link: https://github.com/openwrt/openwrt/pull/15022
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
b14cf98 router: log “Sending a RA on lan” at LOG_DEBUG
c2810fe odhcpd: update cmake file
8c2c065 odhcpd: convert README to markdown
3b96480 odhcpd: allow the use of an alternative cfg file
7328bfe odhcpd: remove confusing #defines
cdb9e5b odhcpd: improve RFC9096 § 3.5 SLAAC compliance
RFC9096 § 3.5 SLAAC compliance introduces a new config option (odhcpd
piofolder), which may wear out the flash under certain conditions (for
example: ISPs with dynamic IPv6 prefixes which disconnect the clients
every X hours).
Therefore, setting "dhcp.odhcpd.piofolder" to persistent storage in the
router flash is not advisable and should be set to other kinds of
persistent storage such as USBs, SDs, NVMEs...
In order to prevent wearing out the router flash it's set to ephemeral
storage by default (tmp):
uci set dhcp.odhcpd.piofolder="/tmp/odhcpd-piofolder"
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
272fc1348ea9 lua: CMakeLists: drop redundant cmake_minimum_required
5e69edac2ec4 CMakeLists: fix CMake warning for INCLUDE macro
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Interface might be down or scanning. Better do a full restart in order to avoid
messing up the runtime state.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve the resilence against power failures during
boot-up by trying to sync the file system before
removing the script. The order of the operations
are important.
Signed-off-by: Markus Gothe <markus.gothe@genexis.eu>
Link: https://github.com/openwrt/openwrt/pull/20248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Plasma Cloud PAX1800-Lite is a dual-band Wi-Fi 6 router, based on MediaTek
MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621AT (880 MHz)
- DRAM: DDR3 448 MiB (Nanya NT5CC256M16DP-DI)
- Flash: 2 MiB SPI NOR (S25FL016K) + 128 MB SPI NAND (W25N02KVZEIR)
- Ethernet: 1x 10/100/1000 Mbps (SOC's built-in switch, with PoE+)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: tri-color LED for status (red, blue, green)
- Buttons: 1x (reset)
- Antenna: 4x internal, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, marked as "3V3 G/RX GND W/TX")
- Power: 12 V DC/2 A (DC jack)
MAC addresses:
WAN: 54:9C:27:xx:xx:00 (factory 0x3fff4, device label)
2.4 GHz: 54:9C:27:xx:xx:02 (factory 0x4, device label +2)
5 GHz: 54:9C:27:xx:xx:08 (factory 0xa, device label +8)
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console (115200 8N1) must be used to access the u-boot shell
during bootup. It can then be used to first boot up the initramfs image
from a TFTP server (here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0x83001000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mt76 as support for generic rates power limits in the devicetree. But the
mt7915 supports beamforming and has another table for configuring the
backoff limits. These can be configured in the DT with the paths-*
properties. The path-*-bf are the ones relevant for beamforming and the
ones without -bf suffix for "traditional" path backoff.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The power-limits for ru and mcs and stored in the devicetree as bytewise
array (often with sizes which are not a multiple of 4). These arrays have a
prefix which defines for how many modes a line is applied. This prefix is
also only a byte - but the code still tried to fix the endianness of this
byte with a be32 operation. As result, loading was mostly failing or was
sending completely unexpected values to the firmware.
Since the other rates are also stored in the devicetree as bytewise arrays,
just drop the u32 access + be32_to_cpu conversion and directly access them
as bytes arrays.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
release is Moderate.
This release incorporates the following bug fixes and mitigations:
Fix Out-of-bounds read & write in RFC 3211 KEK Unwrap.
(CVE-2025-9230)
Fix Timing side-channel in SM2 algorithm on 64 bit ARM.
(CVE-2025-9231)
Fix Out-of-bounds read in HTTP client no_proxy handling.
(CVE-2025-9232)
Reverted the synthesised OPENSSL_VERSION_NUMBER change for the release
builds, as it broke some exiting applications that relied on the previous
3.x semantics, as documented in OpenSSL_version(3).
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4b7638925d3e iptime-crc32: add support for ipTIME AX3000M
12c0b42231be nosimg-enc: add new tool for XikeStor SKS8300 series
2051fe5bc2a1 mktplinkfw2: Add 16MLmtk layout
5d1446bf57d6 tplink-safeloader: Add more special_id's for MR70X
075cdc0c4dd4 iptime-crc32: add support for ipTIME AX3000Q
48ababab6b08 iptime-crc32: add support for ipTIME AX3000SM
f29de74ecd7d iptime-crc32: Add device support for ipTIME AX6000M
3346d7711c9a build: add mkqdimg
950f83405a93 iptime-crc32: add support for ipTIME AX7800M-6E
0725c3d4aa1b build: require CMake >= 3.5 due to dropped legacy support
996dc482a7e8 ptgen: fix misprint and simplify calculation a bit
febfef7a09b1 ptgen: use long long instead of long for sizes
6ea8b6dd44d0 ptgen: fix protective MBR partition size
f1f98b0b8456 ptgen: do not create stub partition to fill a gap if gap caused by alignment
3f2d14829150 ptgen: allow non-default placement of gpt entry table
78d8084c7376 ptgen: allow image generation for a specified disk size
9fa340db640e ptgen: create separate images for gpt data structure
d3f8b6ed940a zynsig: add new tool for creating images for the ZyXEL GS1920 series
7e6f69b444c3 npk_pack_kernel: add tool for creating MikroTik NPK kernel packages
0782d243d23e Revert "ptgen: do not create stub partition to fill a gap if gap caused by alignment"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
after change include/package-pack.mk in 16416782f1, must use ALTERNATIVES to create soft link, otherwise the packing will be messed up.
Fixes: openwrt#20270
Fixes: openwrt#20291
Fixes: 16416782f1 (include: make APK packing mtime reproducible)
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20283
Signed-off-by: Robert Marko <robimarko@gmail.com>
d3be5474f6e6 udebug-cli: ignore zero-length messages in logstream
c79f02d899df ucode: fix skipping lines where the timestamp cannot be parsed
5327524e7153 cmake: bump minimum required version to 3.13
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Right now the sha256sums are only created for the targets/ folder (i.e.
firmware images) and only the buildbot generates those sha256sums. Instead, let
the build system create the sha256sums directly.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The mlxreg-hotplug platform driver was failing to probe due to a missing
I²C multiplexer dependency. Previously, only kmod-i2c-mux-mlxcpld was
declared, but mlxreg also requires kmod-i2c-mux-reg to initialize its
I²C mux functionality.
Without this dependency, the driver probe was deferred:
[ 24.902331] platform mlxreg-hotplug: deferred probe pending: (reason unknown)
With kmod-i2c-mux-reg added, the probe succeeds and the expected
multiplexed I²C buses are registered:
[ 15.793884] i2c i2c-1: Added multiplexed i2c bus 2
[ 15.799391] i2c i2c-1: Added multiplexed i2c bus 3
[ 15.804830] i2c i2c-1: Added multiplexed i2c bus 4
...
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/20274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Radxa ROCK 4D board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20041
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently there's no usable open source TPL implementation for
rk3576 SoCs, so pack the prebuilt firmware from the vendor.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20041
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When a phy appears after setup has already been attempted, tell netifd
to retry setup for all failed wireless devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used by other services to trigger reconfiguration, or detect when
PHY renaming has been performed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ensures that renaming is handled properly. For disabled radios, setup is
performed with an empty list of interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If there is used $(PKG_NAME) in PKG_SOURCE_URL,
then it can not be copy&pasted to the browser's address bar.
Let's remove $(PKG_NAME) and use hardcoded project name
in the PKG_SOURCE_URL
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20193
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
c3bf8fd913a4 interface: fix reload for devices that point to vlan aliases
22216cac7c94 bridge: fix reload when ports refer to aliased vlans on another bridge
ecca21ca07dd system: add logging wrappers for basic system functions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The u-boot of cmcc_rax3000m_*-ddr3 declares a dependency on
trusted-firmware-a-mt7981-*-ddr3-1866mhz, while actually packages
the normal BL2. This causes build failure if the the non-1866m
variant isn't built.
According to the previous commit, it's intended to use the lower
frequency variant to fix device stability issues. Correct
BL2_DDRTYPE as intended.
Fixes: 028050da69 ("mediatek: CMCC RAX3000Me: fix stability issues")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix a typo on defining the PHY package kmod description that reference
phy-aeonsemi-as21x1x package instead of phy-aeonsemi-as21xxx.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Do not allow hostapd phy state update to bring up links as long between mld_set
and mld_start calls. Configuration on other PHYs could still be pending.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bring up AP interfaces, even if no frequency update was provided.
Fixes bringup when a MLO STA on the same radios connects to fewer links
than available, or to a non-MLD AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make the package empty if ucode wifi scripts are being used (since iwinfo is
provided by wifi-scripts in that case). This fixes packages that explicitly
select iwinfo
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are no supported drivers where it even makes sense to disable WMM
anymore, since so much depends on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gpio pwm driver is only available on kernel 6.11+.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20187
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix typo in patch file suffix.
Signed-off-by: Wei-Ting Yang <williamatcg@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20178
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for U-Boot for Airoha EN7581/AN7583. For EN7581
initial patch are already in U-Boot mainline and doesn't require
backport, for AN7583 some patch are still pending but already posted
upstream.
Also add for now, precompiled binary for ATF BL2 and BL31. Support for
ATF is planned and will come later.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Removed upstreamed patch: 0001-Don-t-keep-the-store-open-in-by_store_ctrl_ex.patch
Release notes:
This is a bug fix release.
This release incorporates the following bug fixes and mitigations:
Added FIPS 140-3 PCT on DH key generation.
Fixed the synthesised OPENSSL_VERSION_NUMBER.
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20133
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the generic kernel PWM GPIO driver as module to avoid the need
to build it into the kernel.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://github.com/openwrt/openwrt/pull/20160
Signed-off-by: Robert Marko <robimarko@gmail.com>
The option is an array, and for each entry there should be one generated
line in hostapd.conf. Commas also need to be replaced with whitespace
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Removing the last remaining link from an MLD AP interface removes the
interface as well. Re-create the interface if necessary on config changes.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Can also be used for a client mode interface that is able to connect on
multiple bands individually, while handling hostapd state for the correct
band.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- fix the variable name in the configuration file
- provide a default scan list in case the user did not configure it (MLO preparation)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mlo specific hostapd ubus call from wireless handler to netifd core
ucode script. This avoids unnecessary queueing and the fake MLO wireless
device.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit fixes stability issues on certain RAX3000Me devices. Some
devices has DDR3 RAM which don't able to work reliably at 2133 MHz
and require special BL2 (1866 MHz RAM freq).
Fixes: https://github.com/openwrt/openwrt/issues/20046
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new profiles are intended for devices with DDR3 RAM which
don't able to work reliably at 2133 MHz.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit add kernel module support for Infineon DPS310/DPS368/DPS422
digital barometric air pressure and temperature sensor.
Test on custom board based on Mediatek MT7988a.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20101
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make sure that the package gets updated after the last fix.
Fixes: cd20ae44f2 ("uqmi: fix data-format parsing")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
wda-get-data-format now returns an object instead of a single string.
Account for this change when reading the packet data format.
Suggested-by: Sebastian Ertz (https://github.com/sebastianertz)
Signed-off-by: David Bauer <mail@david-bauer.net>
The EN751221 has an XHCI that is compatible with MT7621.
While there is setup logic in the vendor code for both
EN751221 and MT7621, but MT7621 does not use it in mainline
or OpenWRT, and it appears to work correctly with EN751221.
Include SCSI / Mass Storage because many EcoNet devices
contain a builtin USB SD-Card reader.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20050
[Remove usb storage kmod from smartfiber_xp8421-b]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New upstream release. Debian changelog:
* New upstream microcode datafile 20250812 (closes: #1110983, #1112168)
- Mitgations for INTEL-SA-01249 (processor Stream Cache):
CVE-2025-20109: Improper Isolation or Compartmentalization in the
stream cache mechanism for some Intel Processors may allow an
authenticated user to potentially enable escalation of privilege via
local access. Intel also disclosed that several processors models
had already received this mitigation on the previous microcode
release, 20250512.
- Mitigations for INTEL-SA-01308:
CVE-2025-22840: Sequence of processor instructions leads to
unexpected behavior for some Intel Xeon 6 Scalable processors may
allow an authenticated user to potentially enable escalation of
privilege via local access.
- Mitigations for INTEL-SA-01310 (OOBM services module):
CVE-2025-22839: Insufficient granularity of access control in the
OOB-MSM for some Intel Xeon 6 Scalable processors may allow a
privileged user to potentially enable escalation of privilege via
adjacent access.
- Mitigations for INTEL-SA-01311 (Intel TDX):
CVE-2025-22889: Improper handling of overlap between protected
memory ranges for some Intel Xeon 6 processors with Intel TDX may
allow a privileged user to potentially enable escalation of
privilege via local access.
- Mitigations for INTEL-SA-01313:
CVE-2025-20053: Improper buffer restrictions for some Intel Xeon
Processor firmware with SGX enabled may allow a privileged user to
potentially enable escalation of privilege via local access.
CVE-2025-21090: Missing reference to active allocated resource for
some Intel Xeon processors may allow an authenticated user to
potentially enable denial of service via local access.
CVE-2025-24305: Insufficient control flow management in the Alias
Checking Trusted Module (ACTM) firmware for some Intel Xeon
processors may allow a privileged user to potentially enable
escalation of privilege via local access.
- Mitigations for INTEL-SA-01367 (Intel SGX, TDX):
CVE-2025-26403: Out-of-bounds write in the memory subsystem for some
Intel Xeon 6 processors when using Intel SGX or Intel TDX may allow
a privileged user to potentially enable escalation of privilege via
local access.
CVE-2025-32086: Improperly implemented security check for standard
in the DDRIO configuration for some Intel Xeon 6 Processors when
using Intel SGX or Intel TDX may allow a privileged user to
potentially enable escalation of privilege via local access.
- Fixes for unspecified functional issues on several Intel Core and
Intel Xeon processor models.
* Updated microcodes:
sig 0x000606a6, pf_mask 0x87, 2025-03-11, rev 0xd000410, size 309248
sig 0x000606c1, pf_mask 0x10, 2025-03-06, rev 0x10002e0, size 301056
sig 0x000806f8, pf_mask 0x87, 2025-04-04, rev 0x2b000643, size 592896
sig 0x000806f7, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f6, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f5, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f4, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f8, pf_mask 0x10, 2025-04-08, rev 0x2c000401, size 625664
sig 0x000806f6, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000806f5, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000806f4, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000a06a4, pf_mask 0xe6, 2025-03-19, rev 0x0025, size 140288
sig 0x000a06d1, pf_mask 0x95, 2025-05-15, rev 0x10003d0, size 1667072
sig 0x000a06d1, pf_mask 0x20, 2025-05-15, rev 0xa000100, size 1638400
sig 0x000a06f3, pf_mask 0x01, 2025-05-03, rev 0x3000362, size 1530880
sig 0x000b06a2, pf_mask 0xe0, 2025-02-24, rev 0x4129, size 224256
sig 0x000b06a3, pf_mask 0xe0, 2025-02-24, rev 0x4129
sig 0x000b06a8, pf_mask 0xe0, 2025-02-24, rev 0x4129
sig 0x000b06d1, pf_mask 0x80, 2025-05-21, rev 0x0123, size 80896
sig 0x000c0662, pf_mask 0x82, 2025-05-14, rev 0x0119, size 90112
sig 0x000c06a2, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c0652, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c0664, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c06f2, pf_mask 0x87, 2025-04-15, rev 0x210002b3, size 564224
sig 0x000c06f1, pf_mask 0x87, 2025-04-15, rev 0x210002b3
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc (Intel N150 PC)
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20045
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds kernel packages for the Vitesse VSC73XX switches.
I have split the switch into explicit SPI and platform integrated
variants as it's quite a bit of code.
Link: https://github.com/openwrt/openwrt/pull/20057
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2ae08749a87e ucode: add padding to uc_resource_ext_t
7931bd901222 socket: add socket.pair()
4cd07cd66ab3 socket: add socket.open()
6350e6383ff3 struct: implement X and Z formats for hex and base64 coding
e632e6da1fbc vm: fix potential eyond end of array accesses
a7ead3169ebf resolv: properly handle multiple TXT strings
9d782ea4af63 math: Add an optional range to rand()
Fixes: https://github.com/jow-/ucode/issues/315
Fixes: https://github.com/jow-/ucode/issues/321
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2859741d971e dhcpv4: store reqopts as uint8_t
6d342cc03bf7 odhcpd: add DNR (RFC 9463) support
c89b8b3f2ff3 odhcpd: make the IPv6 RA DNR lifetime configurable
066b3dc6ec1a netlink: fix a memory leak
171140e90b6a odhcpd: add a helper function for addr6/prefix parsing
5585b969c18f router: move pref64 calculations to the config stage
4308384748be dhcpv6: add ipv6 pxe support
6e1ad492cef5 router: replace ssize_t with size_t
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20022
Signed-off-by: Robert Marko <robimarko@gmail.com>
Version 6.15 - 29-Aug-2025
* netlink: fix missing headers in text output
* netlink: fix print_string when the value is NULL
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20021
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PKG_MAKE_FLAGS is required when compiling r8168-rss
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20001
Signed-off-by: Robert Marko <robimarko@gmail.com>
While these boards have an at24 EEPROM for storing the MAC address,
early revisions (up until about 2017) did not contain actual addresses.
Create a random address to have ethernet function properly in u-boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The version of libxml2 was bumped from 2.13.6 to 2.14.5. Since version
2.14, libxml2 is not binary compatible with older versions. Therefore
add an abi version.
From the NEWS file:
Binary compatibility is restricted to versions 2.14 or newer. On ELF
systems, the soname was bumped from libxml2.so.2 to libxml2.so.16.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/19983
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gettext-full only provides libintl which is not licensed under
GPL-3.0.-or-later but under LGPL-2.1-or-later as stated in
gettext-runtime/intl/COPYING.LIB
Fixes: c10d97484a (Add more license tags with SPDX identifiers)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19943
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
