Upstream 2b81db8a7f4475e141a8ffd7cc745ed9f15962df introduced several new
symbols. This commit adds them and also applies alphabetical order via
./scripts/kconfig.pl target/linux/generic/config-6.12
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22276
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 68c8042e9b)
Link: https://github.com/openwrt/openwrt/pull/22699
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems the bootloader does not use 115200, which the dtsi file
specifies. Remove it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8d1b2596ee)
Needed so that the WiFi interfaces come up properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52d776ac96)
Users report pll-data is needed for gigabit speeds.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 469c6676b7)
Add support for Airoha EN7581/AN7583 NPU variant firmware present in
linux-firmware. The Airoha EN7581 NPU variant is to support devices
equipped with the MT7996 WiFi chip.
While at it also add an extra new line to follow pattern of double new line to
separate each firmware package.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 57bf713ef7)
Link: https://github.com/openwrt/openwrt/pull/22371
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXqmiX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
(cherry picked from commit e83da3bada)
Link: https://github.com/openwrt/openwrt/pull/22254
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXmbimX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
(cherry picked from commit 764c503a2c)
Link: https://github.com/openwrt/openwrt/pull/22254
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This access point is a ‘friend’ of the T56 supplied by Odido but with DDR3 RAM and with two Ethernet 2.5 (GPY211)
The flash procedure is similar to other Zyxel T56/EX5600/EX5601
If you need backup please use the T56 guide
Please refer to https://openwrt.org/inbox/toh/zyxel/wx5600-t0 for detailed flash informations
Specifications:
SOC: MT7986b
RAM: 512MB
Flash: 512 MB SPI NAND
Ports: 2 LAN 2.5Gbps (GPY211C)
WIFI: MT7976GN + MT7976AN
LED: 3 bicolor LED - 1 monocolor LED
Buttons: Reset and WPS
We can install all with U-boot and mtk_uartboot.
Load Uboot:
```
./mtk_uartboot -a -p ./mt7986-ram-ddr3-bl2.bin -s /dev/ttyUSB0 -f openwrt-mediatek-filogic-zyxel_wx5600-t0-ubootmod-bl31-uboot.fip
```
**WARNING: Please use a GBIT ethernet or force it on system**
**WARNING: Please use only LAN2 port in Uboot**
Press 0 on Bootmenu
```
mtd erase ubi
run ubi_format
bootmenu
```
Load and write BL2 and U-boot:
```
8
7
```
Load and write recovery and production
```
6
5
```
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Co-authored-by: Hal Martin <halmartin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18364
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 09a0462ea8)
Link: https://github.com/openwrt/openwrt/pull/22659
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This access point is a ‘friend’ of the T56 supplied by Odido but with DDR3 RAM and with two Ethernet 2.5 (GPY211)
The flash procedure is similar to other Zyxel T56/EX5600/EX5601
If you need backup please use the T56 guide
Please refer to https://openwrt.org/inbox/toh/zyxel/wx5600-t0 for detailed flash informations
We can install all with U-boot and mtk_uartboot.
Load Uboot:
```
./mtk_uartboot -a -p ./mt7986-ram-ddr3-bl2.bin -s /dev/ttyUSB0 -f openwrt-mediatek-filogic-zyxel_wx5600-t0-ubootmod-bl31-uboot.fip
```
**WARNING: Please use a GBIT ethernet or force it on system**
**WARNING: Please use only LAN2 port in Uboot**
Press 0 on Bootmenu
```
mtd erase ubi
run ubi_format
bootmenu
```
Load and write BL2 and U-boot:
```
8
7
```
Load and write recovery and production
```
6
5
```
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Link: https://github.com/openwrt/openwrt/pull/18364
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1dbb2d55ac)
Link: https://github.com/openwrt/openwrt/pull/22659
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of redifining the DEVICE_PACKAGES, make sure to expand the list
so yafut is excluded by default as well by $(Device/mikrotik_nor)
Fixes: 13fd9a9ce0 ("ath79: remove kmod-ath9k and wpad from Mikrotik RB750r2")
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit dfbaf84650)
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22667
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sgmiisys0 override uses
/delete-node/ mediatek,pnswap;
but mediatek,pnswap is a property, not a child node. The correct
directive would be /delete-property/. As a result, this statement never
had any effect and the property was never removed.
Drop the incorrect override.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22046
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fc109d1df0)
Link: https://github.com/openwrt/openwrt/pull/22628
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Keenetic/Netcraze (K/N)AP-630
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB SPI NAND
- 1 led with two colors (green, orange)
- 1 button (reset)
- 1 2.5Gbit POE ethernet port based on Airoha EN8811H phy
Serial Interface:
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
Notes:
- The device supports dual boot mode
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Copy image to tftp server.
a) Keenetic
Rename "openwrt-mediatek-filogic-keenetic_kap-630-squashfs-factory.bin"
to "KAP-630_recovery.bin" and place it in tftp server directory.
b) Netcraze
Rename "openwrt-mediatek-filogic-netcraze_nap-630-squashfs-factory.bin"
to "NAP-630_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21634
(cherry picked from commit 20644af030)
Link: https://github.com/openwrt/openwrt/pull/22627
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL8261BE 10GbE PHY's `reset-deassert-us` was set to 100ms (100000us),
but the **RTL8261N datasheet (Table 108, parameter t7)** specifies a
minimum **SMI-ready time of 150ms** after nRESET release before the MDIO
(SMI) bus can be used.
Note: Essentially, the RTL8261N and RTL8261BE are architecturally identical
chips, so their initialization parameters should be consistent.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22575
(cherry picked from commit 44a52a8769)
Link: https://github.com/openwrt/openwrt/pull/22626
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add menuconfig options to include modules for (virtio) vsockets. These are
used when running as Guest OS in a VM.
OpenWRT can be run in a vm (mostly commonly on the x86/64 and armsr
targets). Often it is convenient to have some sort of guest agent running,
to ease communication from host to guest.
Virtual Sockets provide this communication channel.
Virtio is a transport for this communication channel.
Virtual Sockets over virtio are for example used by Incus.
Virtual Sockets in general are used by most hypervisors, including VMware,
Hyper-V, and libvirt (qemu). These may need other transport-specific
modules not included in this commit.
Signed-off-by: Mathijs Rietbergen <mathijs.rietbergen@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21392
(cherry picked from commit c88e8a9816)
Link: https://github.com/openwrt/openwrt/pull/22602
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the blamed commit, the wrong partition name for ART was used.
It was later discovered that the partition table uses "0:ART" instead of
"art" for the ART partition name thus breaking caldata extraction.
So, fix the partition name.
Fixes: 274f6e5ab8 ("treewide: linksys: use nvmem MAC for hw_mac_addr")
Signed-off-by: Anthony Sepa <protectivedad@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22596
Signed-off-by: Robert Marko <robimarko@gmail.com>
Certain targets for an7581 and an7583 referred to kmod-pwm-airoha;
however in the target modules makefile the module is referred to
as kmod-pwm-an7581, causing buildbot to fail.
Change the name of kmod-pwm-an7581 to kmod-pwm-airoha to resolve this.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/22445
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7d2c244646)
Link: https://github.com/openwrt/openwrt/pull/22466
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RB750r2 (HEXLite) does not have wifi and those packages bloat the image
by a significant amount. When building a custom image with WireGuard and
booting that from initramfs, there wasn't enough space left in tmpfs to
upload and flash the squashfs image. Investigating what packages I could
remove, I discovered these unneeded ones.
Signed-off-by: Eicke Herbertz <wolletd@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/22134
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 42cd486787)
Link: https://github.com/openwrt/openwrt/pull/22475
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix execution of initramfs image on Huawei AP5030DN and AP6010DN by
increasing available memory for LZMA extraction by the loader.
The default leaves only ~23.6 MB between the decompression target
and the running loader code. Extracting images with built-in
packages lead to overwriting the loader code. This causes
the decompression to produce garbage output and hang.
Fix this by overwriting LZMA_TEXT_START to increase the
available memory for LZMA extraction to ~39.6 MB.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/22581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 17784ad785)
The Xiaomi Redmi/Mi Router AC2100 does have the correct label mac on the WAN interface.
This MAC is available as gmac1.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/22567
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b1713d623b)
When the fan control script was first implemented, a variable was wrongly
named. The fan probably never turns on - fix that.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/22531
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 41d6584d9b)
If the user removes all /lib/apk/packages/*.conffiles* files to prevent
sysupgrade from preserving configuration, the glob no longer matches and
sysupgrade ends up calling cat on a non-existent path:
cat: can't open '/lib/apk/packages/*.conffiles_static': No such file or directory
Fix this by using find cmd.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/22071
(cherry picked from commit 10db6fc26e)
Link: https://github.com/openwrt/openwrt/pull/22566
Signed-off-by: Robert Marko <robimarko@gmail.com>
The kernel load address was changed in commit e2d823d068 ("ramips:
fix LZMA decompression error for TP-Link EAP615-Wall"). We also need
to relocate the load address for initramfs image so that it can be
booted correctly.
Fixes: e2d823d068 ("ramips: fix LZMA decompression error for TP-Link EAP615-Wall")
Fixes: https://github.com/openwrt/openwrt/issues/22505
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22562
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e5d8f5fd69)
Modern gawk rejects C-style /* ... */ comments in AWK code, treating
them as regex patterns where '*' has nothing to quantify. Replace all
such comments with AWK-style '#' comments in lantiq_bdi_conf.awk and
lantiq_ram_init_uart.awk.
Also replace the pattern 'if (x) /* comment */ else action' which used
a C comment as a null statement with the equivalent 'if (!x) action'.
Fixes build error:
awk: error: ? * + or {interval} not preceded by valid subpattern
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Link: https://github.com/openwrt/openwrt/pull/22458
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9b1f73ec31)
lantiq_gswip and tag_gswip were not loaded during failsafe, leaving the
switch uninitialised. This caused LAN1 port to show no link, making
SSH-based recovery impossible.
Add the autoload flag and include tag_gswip (which was also missing from
the autoload list) so the switch initialises correctly in failsafe mode.
Tested on BT HomeHub 5A (lantiq/xrx200).
Fixes: https://github.com/openwrt/openwrt/issues/22480
Signed-off-by: Benjamin Levine <benjaminmileslevine@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22514
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 20ae49dde7)
NVMEM on MMC was added in dts but the corresponding option was not added
to the config.
Fixes: ee5999c ("treewide: linksys: use nvmem MAC for hw_mac_addr")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22539
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 8f33ecf214)
The issue described in the patch has been fixed by commit
604355e8c4 ("kernel: fix fraglist GRO on linux 6.12")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22525
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit b9299ae0e7)
"qca,gpio-mask" used to be read between ath9k_hw_init() and
ath9k_init_queues(). After 12913c3c56
it is read in ath9k_of_init(), but it gets overwritten by
ath9k_gpio_cap_init() during the call of ath9k_hw_init(), and causes
https://github.com/openwrt/openwrt/issues/22340
If keeping the most of 12913c3c56,
ath9k_gpio_cap_init() could be patched to keep the existing non-zero
gpio mask (coming from device tree).
Tested on Netgear WNDR4500 v3:
[ 22.558083] ath9k 0000:00:00.0: enabling device (0000 -> 0002)
[ 22.569548] ath: phy1: Use overridden gpio mask 0xf6ff
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/22376
(cherry picked from commit a1f5273)
Link: https://github.com/openwrt/openwrt/pull/22508
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, devices having two cpu ports to the switch managed by swconfig,
especally those with qca955x, line tplink archer c7 v2 and linksys ea4500 v3,
use vlan on different cpu port to separate networks by default. (e.g. eth1.1
for lan, eth0.2 for wan)
However, untagging to these vlans cpu ports, and limiting vlans in the switch
on these devices could effectively offload the expense to process vlan tag from
cpu to the switch, and increase the throughput of lan <-> wan ipoe routing.
Tested on my tplink tl-wdr4900 v2, where ucidef_add_switch "switch0"
"0u@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6u@eth0" "1:wan" finally generates
on /etc/config/network:
config device
option name 'br-lan'
option type 'bridge'
list ports 'eth1'
config interface 'lan'
option device 'br-lan'
option proto 'static'
list ipaddr '192.168.1.1/24'
option ip6assign '60'
config interface 'wan'
option device 'eth0'
option proto 'dhcp'
config interface 'wan6'
option device 'eth0'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '2 3 4 5 0'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '1 6'
and the throughput of lan <-> wan ipoe routing with software flow offload
increases from around
[850 Mbps](https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500#nat_performance)
to 900 Mbps.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/19444
(cherry picked from commit d35d92a)
Link: https://github.com/openwrt/openwrt/pull/22509
Signed-off-by: Robert Marko <robimarko@gmail.com>
