In order to keep a coherent set of dependencies of the packages in the
target specific packages (nonshared) in the stable 25.12.0 release
repositories and keep ImageBuilders and ASU functional, hard code the
abi-version used in that builbot phase1 run: "20260213".
*abi compatibility has not changed between 20260213 and 20260313 anyway.
Fixes: 8aac058ef0 ("libubox: update to Git HEAD (2026-03-13)")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22437
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mt76 tracks the PSM state of a sta internally with a wcid flag. TX to
such clients is skipped based on the presence of this flag.
This flag was not added to the PS state notify handler for MT7915 chips.
Without this flag, mt76 queues pending frames to the hardware,
accounting for airtime when a PSM notification is received while in a TX
iteration.
Set the PS flag for the STA WCID to prevent this from happening. TX gets
skipped in presence of this flag.
Link: https://patchwork.kernel.org/project/linux-wireless/patch/20260313112502.2026974-1-mail@david-bauer.net/
Signed-off-by: David Bauer <mail@david-bauer.net>
- Fix RTL8261N 10GbE PHY `reset-deassert-us` from 100ms to 221ms to meet datasheet minimum SMI-ready timing (t7 >= 150ms), fixing intermittent boot stalls caused by MDIO bus instability
- Add missing WLAN toggle button (GPIO 34) present in stock firmware but absent from OpenWrt DTS
- Fix memory size from 1 GB to the actual 512 MB
Fix 1: The RTL8261N 10GbE PHY's `reset-deassert-us` was set to 100ms (100000us), but the **RTL8261N datasheet (Table 108, parameter t7)** specifies a minimum **SMI-ready time of 150ms** after nRESET release before the MDIO (SMI) bus can be used.
With only 100ms, the kernel attempts MDIO bus access before the RTL8261N's SMI interface is stable. Since the RTL8261N (mdio-bus:00) and the internal MT7988 2.5GbE PHY (mdio-bus:0f) share the same MDIO bus, a not-yet-ready RTL8261N disrupts all MDIO traffic, causing the 2.5GbE PHY firmware loading (`mt798x_2p5ge_phy_config_init`) to stall.
Observed symptoms on warm reboot:
- Sometimes `mt798x_2p5ge_phy_config_init` hangs for 5+ minutes or indefinitely
- RCU CPU stalls (`rcu: INFO: rcu_sched detected stalls on CPUs`)
- mt7996e WiFi chip message timeouts cascading to `chip full reset failed`
- System appears hung with only power LED blinking slowly
UART serial log evidence (warm reboot with 100ms):
```
[ 73.041756] rcu: INFO: rcu_sched self-detected stall on CPU
[ 73.048341] rcu: 2-....: (8 ticks this GP)
[ 73.061641] pc : mt798x_2p5ge_phy_config_init+0x258/0xbb0
[ 73.061653] lr : mt798x_2p5ge_phy_config_init+0x238/0xbb0
...
[ 334.771280] MediaTek MT7988 2.5GbE PHY mdio-bus:0f: Firmware date code: 2024/10/30
```
The 2.5GbE PHY firmware loading, which normally takes ~3 seconds, took **325 seconds** due to MDIO bus instability. In the worst case, the system never recovers.
GPL DTS uses 221ms (`reset-deassert-us = <221000>`), providing 71ms of margin above the 150ms datasheet minimum. All MediaTek MT7988 reference board DTS files in the GPL use this same 221ms value.
Fix 2: Missing WLAN button (GPIO 34)
The BE450 has a physical WLAN toggle button on GPIO 34, defined in the stock TP-Link GPL DTS but missing from the OpenWrt DTS. Without this definition, the button is non-functional under OpenWrt.
The pin name for GPIO 34 in the MT7988 pinctrl is `SPI2_MISO`, confirmed by the kernel pinctrl driver (`pinctrl-mt7988.c`: `MT7988_PIN(34, "SPI2_MISO")`) and the official devicetree binding (`mediatek,mt7988-pinctrl.yaml`).
Note: GPIO 34 is also used by the BE450's First U-Boot as a recovery button (web recovery 192.168.1.1). Registering it in the DTS ensures the kernel claims the pin.
Fix 3: Incorrect memory size in DTS
The OpenWrt DTS declares 1 GB (`0x40000000`) of RAM, but the BE450 has 512 MB (`0x20000000`).
Run tested.
Signed-off-by: Semih Baskan <strst.gs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22386
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f2699cce13)
* e3f6a41 main: exit 1 when showing the usage
* b17c31f main: exit 1 on getopt() errors
* e086664 lexer: fix a minor memleak in jp_get_token()/match_token()
* e5a07f4 main: defer processing until options are processed
* afe72ad main: usage spell fixes
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 2c2cea8864)
58eb263 instance: don't print error in case cgroups are disabled
9baf019 instance: use positive error numbers for strerror()
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 5ba55feb10)
RTL838x devices cannot reboot if the flash controller is driven in
4 byte mode. Unitl fdc3776 ("realtek: pcs: fix PLL_CML_CTRL for
serdes 0/1") this bit was luckily cleared by a coding error. Since
then the device cannot be rebooted anymore.
Looking at the SDK one can see that this bit is reset short before
the reboot happens. But we might need that in critical situations
where there is no chance to do it right in time. As the RTL838x
always ran with the bit disabled restore the old behaviour. This
time implement it as a documented quirk so it does not get lost.
Fixes: fdc3776 ("realtek: pcs: fix PLL_CML_CTRL for serdes 0/1")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
(cherry-pick from commit b995f318b2)
Link: https://github.com/openwrt/openwrt/pull/22384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
a52cdb354d13 dns: validate IPv4 record addresses
b798c24205b5 dns: validate IPv6 record addresses
a3dcb4adc635 dns: validate reverse dns query name lengths
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit 8a7eb57ab8)
SFP I2C buses for ports 1 and 3 were swapped as order changed on production
boards.
So, swap them around to fix SFP 1 and 3 failed to read EEPROM errors.
Fixes: 29b3d929a6 ("microchipsw: lan969x: add Novarq Tactical 1000")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 55f1f2c1c4)
When the virtual package "uci-firewall" is installed, the choice
between "firewall" and "firewall4" is arbitrary, sometimes resulting
in one, sometimes the other.
Set the default variant on "firewall4" to make it the preferred
package when installed as a dependency.
Link: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/1126
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22328
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5d71d9a4be)
In the transition to nvmem-layout and subsequent disabling of non layout
u-boot-env, this device was left out.
Transition to nvmem-layout to fix the mac address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22263
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ed70a07d15)
When NVMEM is not ready, of_get_mac_address fails. Handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22305
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eadd81b17e)
When NVMEM is not ready, of_get_mac_address fails. Handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22305
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 04ed8c94ce)
Fix two hardware initialization issues in the EN7581 PCIe controller
and add support for x2 (2-lane) link mode.
Fixes:
The upstream EN7581 PCIe initialization writes EQ presets and PIPE
configuration registers before clk_bulk_prepare_enable(). Since the
MAC clocks are not yet running at that point, these register writes
are silently dropped, leaving the hardware with default values. This
can cause link training failures or suboptimal equalization.
Additionally, after link training the MAC may only advertise Gen1-Gen2
capability in the Link Capabilities 2 register despite the PHY being
configured for Gen3. A serdes reset toggle forces the MAC to re-read
PHY capability, recovering Gen3 8GT/s link speed.
Both issues are addressed by separating PERST from the clock callbacks
(patch 911), allowing the PCIe controller driver to properly sequence
PERST, clock enable, and register writes (patch 912).
New feature:
PCIe x2 mode support for EN7581 using the NP_SCU system controller
for serdes mux routing, PERST management, and lane configuration.
Both bonded MACs are configured for x2 operation with proper EQ
presets before link training begins.
Signed-off-by: Ryan Chen <rchen14b@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21978
Link: https://github.com/openwrt/openwrt/pull/22336
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bump compat version to 3.0 for TP-Link RE355 v1, RE450 v1 and RE450 v2.
Was missed for 25.12; users upgrading from older images need sysupgrade -F.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 03fddee7bd)
Misaligned rootfs_data caused config loss on sysupgrade. Set BLOCKSIZE
:= 4k for proper JFFS2 alignment. Add DEVICE_COMPAT_MESSAGE for
sysupgrade -F requirement.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 831685aa15)
Rename Device/tplink_rex5x-v1 to tplink_rex5x. Make RE355 v1, RE450 v1,
and RE450 v2 inherit from it, removing duplicated fields from RE450 v2.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d583294c70)
Allow reinstalling already-installed packages without a version change.
Only the named packages are reinstalled, not their dependencies.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 91cff1a6d3)
Several OpenWrt-related fixes are included in this release.
Drop upstreamed patches and refresh the rest.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Link: https://github.com/openwrt/openwrt/pull/22240
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ed94d3eea7)
memcpy() with overlapping src and dest buffers is an undefined behavior
in C. In the current code, a ConfRej response is generated by copying
input data in-place, where the dest address is lower than the src.
This happens to work in practice because memcpy() forward-copies data,
matching the behavior of memmove() in this case.
However, if FORTIFY_SOURCE or Address Sanitizer is enabled, memcpy()
will detect the overlap at run time and abort the program.
Replace the memcpy() with memmove() to ensure a well-defined behavior.
Reported-by: Filippo Carletti <filippo.carletti@gmail.com>
MRU patch https://github.com/ppp-project/ppp/pull/573
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22286
(cherry picked from commit 1e9da9798a)
Link: https://github.com/openwrt/openwrt/pull/22318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Removing tmp/ after having built base-files or toolchain currently
breaks rootfs generation:
$ rm -rf tmp
$ make V=w
...
make[2] package/install
cat: .../openwrt/tmp/base-files.version: No such file or directory
cat: .../openwrt/openwrt/tmp/libc.version: No such file or directory
ERROR: 'base-files=' is not a valid world dependency, format is name(@tag)([<>~=]version)
make[2]: *** [package/Makefile💯 package/install] Error 99
The only way to recover from here is to clean toolchain and base-files via
$ make package/{base-files,toolchain}/clean
tmp is supposed to be ephemeral, so clearing it is an expected action,
which normally just triggers a regeneration of all files there.
Fix this by moving the version files to $(STAGING_DIR).
Fixes: 63e178f067 ("build: lock versions for special APK packages")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21803
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a4e92f0484)
Add pending patch for improving Huawei MA5671a SFP fixup, which allows
communicating with the module even if the fiber isn't connected.
(cherry picked from commit eb4fd65c92)
Link: https://github.com/openwrt/openwrt/pull/22283
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The MeshPoint.One was disabled during the DSA migration with the
comment "Missing DSA Setup". However, this device inherits its
entire network configuration from 8dev Jalapeno via the
Device/8dev_jalapeno-common template, and shares the same DSA
network setup in 02_network.
The Jalapeno has been working with DSA since the migration. All
MeshPoint.One board support files (DTS, network config, LED config)
are already in place and reference the same QCA8072 switch
configuration as the Jalapeno.
Hardware: Qualcomm IPQ4018, QCA8072 switch, same as 8dev Jalapeno.
Tested: Built firmware from current main branch, boots and network
functions correctly.
Signed-off-by: Valent Turkovic <valent@meshpointone.com>
Link: https://github.com/openwrt/openwrt/pull/22258
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a75cc4f18c)
Link: https://github.com/openwrt/openwrt/pull/22279
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dave Täht sadly passed away on April 1, 2025. With the OpenWrt 25.12
release, we honor his life and his remarkable contributions.
Dave played a key role in reducing bufferbloat and improving network
latency in OpenWrt and across the wider internet. His work made networks
faster, more responsive, and more reliable for millions of users.
This release is dedicated to his memory and lasting impact on the
networking community.
Dave's Wikipedia article: https://en.wikipedia.org/wiki/Dave_T%C3%A4ht
Link: https://github.com/openwrt/openwrt/pull/22180
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit c053b22573.
KSZ DSA driver is the only thing in the kernel selecting DCB support
instead of depending on it if required.
So, it will enable DCB support without asking and we do not want the
kernel size increase, as well as current Layerscape ARMv8 build failure.
So, revert this until its fixed upstream or worked around.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b897db9c44)
Add some additional Gateworks Venice boards to sysupgrade support.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/22202
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a9f4daa3fe)
Rename the patches folder too and also adapt the name in the toolchain menu.
Without changing the patches folder name the patches are not applied.
Fixes: adad973a9c ("toolchain: binutils: update to 2.45.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 525a1e94b3)
