The BL2 image for mt7987_rfb-emmc should be emmc, not sdmmc.
Fixes: 6d35eda ("uboot-mediatek: add builds for the MediaTek MT7987 reference board")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/23490
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update the uboot-ath79 package to v2026.04 release for ath79 devices.
Tested on:
- NEC Aterm WG600HP (AR9344)
- NEC Aterm WG1400HP (QCA9558)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22901
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The Globitel BT-R320 patch has incorrect line numbers and corrupted
ASCII control characters.
Fixes: a3105d3f95 ("mediatek: filogic: add support for Globitel BT-R320")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23526
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gpio-button-hotplug skips buttons with button->irq set because it cannot
handle true interrupt-only gpio-keys descriptions. That check also skips
valid GPIO-backed buttons that provide a separate interrupt specifier, such
as the Meraki MX60 reset button.
Try to acquire the GPIO descriptor before deciding that an explicit-IRQ
button is unsupported. Continue to skip true interrupt-only buttons, and
make the IRQ setup and teardown paths ignore skipped entries.
Tested on: Cisco Meraki MX60. Reset button now works.
Fixes: 23845fa10b ("gpio-button-hotplug: do not error on interrupt attached keys")
Assisted-by: Codex:GPT-5.5
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23382
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add support for the AlwayLink M01K43 5G CPE router.
Hardware specifications:
- SoC: MediaTek MT7981B (Filogic 820), dual-core Cortex-A53
- RAM: 256 MiB DDR3 (0x40000000, size 0x10000000)
- Flash: 128 MiB SPI-NAND (UBI, root) + 4 MiB SPI-NOR (bootloader)
- Ethernet: 4x 1 GbE LAN + 1x 2.5 GbE WAN
(MT7531 DSA switch; WAN via RTL8221B 2.5GbE PHY on MAC1)
- WiFi: MT7981 built-in 2x2 802.11ax (2.4 GHz + 5 GHz)
- USB: 1x xHCI (USB 2.0 only; USB 3.0 PHY pins not routed)
- Modem: M.2 B-Key slot wired for USB (tested: Quectel RM551E-GL,
Quectel RM520N-GL via QMI)
- LEDs: 10x GPIO LEDs (status, WAN, LAN, WiFi 2.4/5, signal bars)
- Buttons: WPS, Reset, RFKill
- Power: 12 V DC barrel jack
- UART: 3.3 V TTL header on PCB, 115200 8N1, no flow control
PCB silkscreen: M01K43 v5.0
Manufacturer: Shenzhen AlwayLink Wireless Technology Co., Ltd.
MAC addresses come from the 'ledeinfo' partition (mtd6) at offset 0x18
(label macaddr_ledeinfo_18); the stored value is the LAN MAC.
interface this port vendor firmware
------------------- ----------- --------------------------
eth0 / LAN bridge base + 0 base + 0
eth1 / WAN base + 1 base + 1
wifi 2.4 GHz band@0 base + 2 base (driver-derived)
wifi 5 GHz band@1 base + 3 base + LAA bit (driver)
The vendor's ethernet scheme (LAN = base, WAN = base + 1) is reproduced
exactly. For WiFi the vendor's proprietary mt_wifi driver ignores the
stored per-radio MAC and derives each BSSID from the base by setting the
locally-administered bit, so the radios are not given clean unicast
offsets. Under mainline mt76 + DSA, reusing the base (LAN) MAC on a radio
collides at L2 with the gmac0 conduit, so this port assigns the 2.4 GHz
and 5 GHz radios base + 2 and base + 3 — unique unicast addresses in the
same OUI block.
Installation
------------
Stock firmware defaults (verified on shipping units):
LAN IP: 192.168.100.1
SSH/web: user 'root', password 'admin'
Serial: 3.3 V TTL UART header on PCB, 115200 8N1, no flow control
Image artifacts produced by this device definition:
openwrt-mediatek-filogic-alwaylink_m01k43-squashfs-factory.bin
openwrt-mediatek-filogic-alwaylink_m01k43-squashfs-sysupgrade.bin
Before flashing, back up the per-unit partitions (cannot be
regenerated):
ssh root@192.168.100.1
dd if=/dev/mtd3 of=/tmp/factory.bin bs=1 count=655360
dd if=/dev/mtd6 of=/tmp/ledeinfo.bin bs=1 count=65536
exit
scp root@192.168.100.1:/tmp/factory.bin .
scp root@192.168.100.1:/tmp/ledeinfo.bin .
Method 1 - From an existing OpenWrt install (sysupgrade):
IMG=openwrt-mediatek-filogic-alwaylink_m01k43-squashfs-sysupgrade.bin
scp "$IMG" root@192.168.1.1:/tmp/sysupgrade.bin
ssh root@192.168.1.1 sysupgrade -n /tmp/sysupgrade.bin
Method 2 - U-Boot serial recovery via TFTP (requires 3.3 V USB-UART
adapter):
1. Attach 3.3 V USB-UART (TX, RX, GND) to the PCB header. Open a
terminal at 115200 8N1, no flow control.
2. Configure a TFTP server on the host PC at IP 192.168.2.88.
Place the factory image in the TFTP root, renamed if desired.
3. Power on the router. The BL2/U-Boot banner prints within ~1
second; press any key during the autoboot countdown to enter
the U-Boot menu.
4. From the menu, select 'Upgrade ubi'. U-Boot's default IP is
192.168.2.1 and it expects the TFTP server at 192.168.2.88.
Provide the factory image filename when prompted.
5. Wait for the write to complete; U-Boot reboots into OpenWrt.
Method 3 - From a NAND programmer (brick-recovery path):
1. Clip onto or desolder the SPI-NAND chip and dump the full
128 MiB with a programmer (e.g. RT809H, CH341A with NAND
adapter). Keep the dump as a recovery image.
2. Using the same programmer, write the factory.bin image to
the UBI region of the NAND. The SPI-NOR (BL2/u-boot-env/
Factory/FIP/woem/ledeinfo/nvram) must NOT be erased - those
partitions are per-unit and live on the separate 4 MiB NOR.
3. Reseat the chip and power on. The bootloader on NOR will
load the new kernel and rootfs from UBI.
Signed-off-by: Richard Jones <richard@netsolution.shop>
Link: https://github.com/openwrt/openwrt/pull/22818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
he_phy_cap and he_mac_cap in phy_capabilities are only populated inside
the iftype_data loop. On 6GHz-only radios (e.g. QCN9074/ath11k_pci),
when capability bytes are unavailable they remain null, causing null
dereferences in device_htmode_append():
Reference error: left-hand side expression is null
if (!(he_phy_cap[3] & 0x80))
Initialise both to [] before the loop and guard the consumer side with
?? [] so bitwise checks conservatively disable beamformer/beamformee/twt
features rather than crashing.
Link: https://github.com/openwrt/openwrt/issues/23488
Signed-off-by: dastarothx <darkastalier@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23496
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
4b274055ede3 libubus: fix NULL dereference on OOM in ubus_queue_msg
8b5be570f13e libubus-acl: fix dangling pointers on blob_memdup failure in acl_recv_cb
9105ea2a349a ubusd_acl: fix NULL dereference on OOM in ubusd_acl_alloc_obj
07d7f34ac278 ubusd_acl: handle allocation failures in ubusd_acl_init_client
497321a5ea90 ubusd_acl: fix NULL dereference on OOM in ubusd_acl_init
f66d52ba983f ubusd_event: fix OOM handling in ubusd_send_event_msg
11ea1b3bdbea ubusd_main: fix async-signal-unsafe SIGHUP handler
0c095592ccb7 ubusd_proto: fix resource leaks and ID tree corruption in ubusd_proto_new_client
f61695e6e12a ubusd_proto: fix NULL dereference for user/group in ubusd_handle_add_watch
7ecacfadd9bc ubusd_proto: fix NULL dereference on OOM in ubusd_proto_init_retmsg
3ab9d7759545 lua: fix inverted argument check in ubus_lua_add
43051ca73aec lua: fix unchecked calloc and memory leak in ubus_lua_load_object
4ca0b141e9a7 ubusd_id: use getrandom(2) unconditionally on Linux
7e4356da8abe ubusd_monitor: fix NULL dereference on OOM in ubusd_monitor_message
5849870f2251 libubus-req: fix file descriptor leaks in ubus_process_req_msg
f29767f90af1 libubus: fix file descriptor leaks in ubus_process_msg
b099d050b59d libubus: make ubus_shutdown idempotent
a564b8dcb395 ubusd_main: check strdup return value in mkdir_sockdir
239edcbaaac8 ubusd_id: fix continue in do-while skipping random ID retry
09d2df45bf38 ubusd: fix NULL dereference on OOM in ubus_msg_enqueue
bcc45ca981fd libubus: actually set FD_CLOEXEC on the ubus socket
8188f5ce8564 libubus-io: close recv_fd captured before get_next_msg failure
7a068bac5a9b libubus-io: byte-swap peer in HELLO when storing as local_id
747013f6ea05 libubus-io: reset sock.fd to -1 after close on ubus_reconnect error path
020a64b9b169 ubusd_acl: use size_t for strlen result in ubusd_acl_alloc_obj
f92ffd289dcc ubusd: use size_t for string and blob length variables
795b32bb96b6 ubusd: use fixed-width types for sequence counters
Link: https://github.com/openwrt/openwrt/pull/23487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This module adds support for the Corsair Commander Pro and Corsair
Commander Pro (1000D) fan and temperature monitoring controllers.
Signed-off-by: Dee HY <dongfengweixiao@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/23465
Signed-off-by: Robert Marko <robimarko@gmail.com>
7df188543e26 libfstools: enable f2fs overlay compression formatting
16718b6e3c0f libfstools: mount f2fs overlay with zstd compression
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace exit(1) on every failure path with return null so callers that
iterate over multiple radios can collect results from the radios that
did succeed instead of aborting on the first one that refuses an
off-channel scan.
Route diagnostics to stderr via warn() so stdout stays clean for
callers parsing JSON output, and include the device name in each
message to disambiguate per-radio failures.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1bf2d490484e libfstools: make get_var_from_file() reusable
0b6022439cad mount_root: add kernel parameter to specify the overlay storage name
e600d842ce81 mount_root: add kernel parameter to specify the overlay fileystem type
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The chunk length is not correct.
Fixes: d2fabb974c ("mediatek: add support for Wavlink WL-WNT100X3 ubootmod")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The generated firmware patches for RealTek's PHYs are host architecture
agnostic. Express this with PKGARCH:=all.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that the upstream RealTek PHY driver is patched to support also
the new 5G and 10G PHYs we can start to phase-out the messy downstream
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is required by the realtek PHY driver for:
* rtl8261n.bin (package "rtl8261n-firmware" or "rtl8261n-lp-firmware")
- RTL8251L 5Gbps PHY
- RTL8261BE 10Gbps PHY
- RTL8261N 10Gbps PHY
* rtl8264b.bin (package "rtl8264b-firmware")
- RTL8254B 5Gbps PHY
- RTL8264 10Gbps PHY
- RTL8264B 10Gbps PHY
These PHY chips need a sequence of register writes for initialization.
These are provided as firmware files which are interpreted/applied by a
new register patch engine.
For the moment, the patch instructions in rtl8261-firmware and
rtl8264b-firmware are the same as from the rtl8261n driver. This should
make it possible to first evaluate the patch engine and driver development
for switching over in adjusting the patch instructions.
Signed-off-by: Balázs Triszka <info@balika011.hu>
[sven: rebase, split, fix package version/release, use conf from rtl8261n
driver]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[daniel: define VERSION matching source date for the resulting packages]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6ab9abb56bcb cgi, file: fix crash due to field_len type mismatch with libubox
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/23446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use a user-supplied profile-id when configuring the APN and PDP type.
Fall back to id "1" in case no profile-id is set by the user.
Link: https://github.com/openwrt/openwrt/issues/21617
Suggested-by: S. Hoot <spoot_hoot@protonmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The AddDepends/pse-pd helper appended kmod-pse-pd to DEPENDS without the
'+' prefix, making it a hard dependency rather than an auto-selecting one.
This breaks pulling any PSE controller driver (kmod-pse-pd692x0,
kmod-pse-si3474, kmod-pse-tps23881, kmod-pse-regulator, ...) in via a
device's DEVICE_PACKAGES: the kmod itself is auto-selected, but the
unsatisfied hard dep on kmod-pse-pd silently drops it from .config.
Prefix the kmod-pse-pd entry with '+' so it auto-selects, matching how
the other deps in the same file (kmod-i2c-core, etc.) are expressed. The
helper is the right place to fix this; every PSE controller driver routes
through it.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23449
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 90M to 122.25M.
Flashing instructions:
1. Login into the device and backup all your partitions,
especially `Factory` and 'HW' to be able to come back to stock and use all
Wavlink services.
2. Unlock mtd partitions:
```
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
```
3. Upload new `bl2` and `fip` to the router /tmp and write them:
```
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-bl31-uboot.fip fip
mtd erase ubi
```
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt initramfs has booted, prepare ubi and envs:
```
ubidetach -p /dev/mtd4 && ubiformat /dev/mtd4 -y && ubiattach -p /dev/mtd4 && ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB && ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
8. Perform sysupgrade.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
| Component | Details |
|------------------|-------------------------------------------------|
| **SoC** | MediaTek MT7986A (4× ARM Cortex-A53 @ 2.0 GHz) |
| **RAM** | 512 MB |
| **Flash** | 256 MB NAND |
| **Ethernet** | 5× 10/100/1000 Mbps (1 WAN + 4 LAN) |
| **WLAN 2.4 GHz** | MediaTek MT7976GN — 802.11b/g/n/ax, 4×4 MIMO |
| **WLAN 5 GHz** | MediaTek MT7976AN — 802.11n/ac/ax, 4×4 MIMO |
| **LEDs** | 1× RGB LED (GPIO-controlled) |
| **Button** | 1× Reset |
| **USB** | Yes |
**MAC Addresses:**
| Interface | Source |
|------------|-------------------------------------------------|
| WAN/Label | u-boot-env MTD partition, "mac" (text) |
| LAN | WAN + 1 |
| 2.4 GHz | WAN + 2 |
| 5 GHz | WAN + 3 |
---
**1. Prepare TFTP server**
Set a static IP on the ethernet interface of your computer (e.g. default: ip `192.168.1.2`, gateway `192.168.1.1`).
Download the initramfs image and host it with the TFTP server.
**2. Interrupt boot**
Attach UART and power on the router. When the boot menu appears, select **Failsafe Mode**,
then press `Ctrl-C` to interrupt and enter the U-Boot prompt.
**3. Load and run initramfs image**
```sh
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
tftpboot 0x46000000 openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-initramfs-kernel.bin
fdt addr $(fdtcontroladdr)
fdt rm /signature
bootm
```
**4. Flash sysupgrade image**
Place the sysupgrade image in `/tmp`, then run:
```sh
sysupgrade /tmp/openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-squashfs-sysupgrade.bin
```
Alternatively, use the sysupgrade option in LuCI.
Note:
- The raw MTD u-boot-env partition is only used for MAC address storage, while the active U-Boot environment is stored in the UBI volume.
- These devices ship with secure boot enabled and stock U-Boot only accepts vendor-signed FIT images.
- BL2/FIP cannot be replaced, so the stock signature verification path cannot be disabled directly.
- Setting ipaddr='' forces U-Boot to exit the web failsafe path and continue into autoboot.
- The custom bootcmd loads OpenWrt from the UBI volume and removes the /signature node before bootm, allowing unsigned OpenWrt FIT images to boot.
- Stock U-Boot expects its environment in a UBI volume named u-boot-env, so it is created during initial setup.
Signed-off-by: sh3ikh-faisal <sheikhfaisal713@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In case OpenWrt is used to build a custom distribution, the default
button handling logic may be undesired.
Add config options to disable default standard button handling code
at build-time.
Signed-off-by: David Bauer <mail@david-bauer.net>
In case OpenWrt is used to build a custom distribution, the default
button handling logic may be undesired.
Add config options to disable default standard button handling code
at build-time.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add support for Xiaomi AX5400 (RA74).
Specifications:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to an
external QCA8337 switch (3 LAN Ports 10/100/1000)
* Flash: Gigadevice GD5F1GQ5REYIG (128 MiB)
* LEDs: 1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
* Buttons: 1x Reset (GPIO 38 Active Low)
1x WPS (GPIO 28 Active Low)
* MAC address layout: LAN (eth1): 0:art @ offset 0x0
WAN (eth0): 0:art @ offset 0x6
Flash instructions: (use redmi-ax5400 image for the Redmi AX5400)
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/23374
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add KEY_SETUP and KEY_VENDOR keys. Many Rockchip devices, including all of those in
e13cbab684 ("rockchip: enable SARADC; add buttons hotplug and ADC kmods to default packages")
have one or both of these buttons.
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23396
Signed-off-by: Robert Marko <robimarko@gmail.com>
OSLEC has been dropped upstream since Linux 6.16.
Reflect that by no longer providing the kernel module package
`kmod-echo` which essentially became an empty stub.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- Sync shared U-Boot DTS nodes with the main device DTS
- Remove duplicate strings
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22929
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix instability by reducing RAM speed to 1866 MT/s
in line with Winbond W634GU6RB-11 specs.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22929
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, there is no SBOM generation in imagebuilder when the package
system 'apk' is used. This commit adds this feature back. This already
worked for the package system 'opkg'.
Furthermore, generating the SBOM using perl is not reproducible if the
input data has not changed. A different file is always generated. This is
not the case with Python. For this reason, Python is now used to generate
the SBOM for the imagebuilder.
The script has already been prepared so that it can also process the opkg
package system for generating the SBOM.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Update package to the latest stable version.
Patches unchanged.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/23369
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the netis MEX605, which is a variant based on the netis NX30 V2.
1. Update brand naming from Netis to netis to follow the official branding.
2. Rename NX30V2 to NX30 V2 to correctly reflect it as the second version of the NX30.
3. Update variant notation for consistency.
cherry picked from commit c982357
1. Add 'model' to the DTS for netis NX30 V2 and define WiFi LED.
4. Fix typo.
Signed-off-by: Zhiwei Cao <bfdeh@126.com>
Signed-off-by: David Han <h96643864@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22726
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This improves on openwrt/openwrt@aeb9028aab by adding support for
other Dell EMC Edge620/640/680 devices and mapping
the interfaces to match the markings on the device.
This modifies the netdevices.mk file to set the boot flag for
ixgbe driver to load it in early stage of the boot process to
allow for proper mapping of the network interface PCI paths
inside the 02_network script. This will also allow other devices
using the ixgbe driver to do proper mapping in 02_network script.
The 02_network script is then modified to support all
dell-emc-620/640/680 devices. It now maps the network
interfaces via PCI paths to match the markings on the device.
The interface marked GE6 is still used for WAN with
interfaces GE1-GE5 used for LAN.
The SFP1 and SFP2 interfaces are left to be assigned by
the user.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/23110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ethernet LAN port is set to `eth1` (silkscreen "ETH2" and case label "2") next to the 2x USB Type-A
ports and WAN is set to `eth0` (silkscreen "ETH1" and case label "1") next to the USB Type-C port.
The USER ("reset") button serves as the reset button. A short press will reboot and a long press
will reset to factory settings (deleting all data) if using squashfs image.
MASK ("maskrom") and RCRY ("recovery") buttons are enabled but are not set to any specific function
Pressing the POWER button will `poweroff` the device and it will stay off until a power cycle.
Hardware
---------------
* SoC: RockChip RK3576 64-bit ARMv8-A 8 cores big.LITTLE (4x A72 and 4x A53)
* RAM: 3/4GB LPDDR4X or 8/16GB LPDDR5
* Ethernet: 2x GbE (SoC RGMII MAC, RTL8211F PHY)
* 3x LEDs (SYS - red / 1 (WAN) - green / 2 (LAN) - green)
* 4x Buttons (MASK ("maskrom"), RCRY ("recovery"), USER ("reset" - OpenWrt reset), POWER)
* 1x 16MiB SPI NOR on board
* 1x UFS slot for optional UFS 2.0 module (currently not supported)
* 1x microSD card slot (UHS-I)
* 1x HDMI OUT
* 1x Headphone OUT 3.5mm
* 1x M.2 M-key 2280 PCIe slot (PCIe 2.1 x1 supports NVMe SSD)
* 1x M.2 E-key *SDIO* slot for optional RTL8822CS Wi-Fi 5
* the case has integrated antennae as well as 2x knockouts
* the device tree is missing the nodes relevant to Wi-Fi operations so it's not supported for now.
* 2x USB 3.2 Gen 1 Type-A Ports
* Power: 1x USB Type-C 6V-20V with both DC and USB PD supported
* Serial: 1500000 8N1 3.3V - 2.54mm 3-pin header next to HDMI
MAC addresses
---------------
WAN (`eth0` case label "1"): generated from /sys/.../mmcblk0/cid (CID of SD card)
LAN (`eth1` case label "2"): WAN + 1
Installation
---------------
Decompress the archive of the OpenWrt sysupgrade image and write it to a microSD card using `dd`
or use Balena Etcher (no need to decompress).
Boot
---------------
Insert microSD card, set boot switch to "UFS/SD" and then supply power.
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apply pending U-Boot patches so that Rockchip RK3576 devices can boot from SD card. The problem:
"The BootROM on RK3576 has an issue loading boot images from an SD-card. This issue can be worked
around by injecting an initial boot image before TPL…and return to BootROM to load next image, TPL"
Compilation of the initial boot image has been added to the U-Boot build recipe.
Tested on FriendlyELEC NanoPi M5
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Select `CONFIG_ROCKCHIP_SARADC=y` to enable Rockchip SAR ADC
Add ADC Ladder Buttons driver as a kernel module as well as `kmod-button-hotplug` to the list of
default packages for Rockchip targets that have buttons connected to ADC, not including some
devices (e.g. NanoPi R76S) that have ADC buttons which are not in the device tree.
This is needed to use buttons on Rockchip devices that are connected to ADC and not GPIO
Tested on FriendlyELEC NanoPi M5
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes wrong bl2 dependency which leads to build errors if
non-ubi ddr3-1866 bl2 is not exists in the build dir.
Fixes: 9a87c4b ("uboot-mediatek: add Qihoo 360T7 (UBI) support")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23354
Signed-off-by: Robert Marko <robimarko@gmail.com>
