The Mediatek pinctrl driver can only accepts drive-strength values
enumerated in "dt-bindings/pinctrl/mt65xx.h".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the missing "device_type" property to fix the memory node. The
Linux kernel can not get the memory size without it. Though u-boot
can automatically fixup the memory node by adding the "device_type"
and "reg" properties if the CONFIG_ARCH_FIXUP_FDT_MEMORY symbol is
enabled, it's better not to rely on this optional feature. This
patch also adds the reg address for the memory node name to follow
the naming rules.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When testing LLDP and STP, we observed that locally generated multicast
packets (e.g. LLDP, STP) were not restricted to the designated output
port(s). For example, when transmitting on `lan1`, the same packet was also
forwarded to other ports such as `lan2`.
Steps to reproduce:
1. Configure lldpd to use `lan1` in UCI and restart the service
2. Connect devices to `lan1` and `lan2`
3. Observe that the device on `lan2` still receives LLDP packets
The issue was caused by an incorrect `FWD_TYPE` setting in the TX CPU TAG,
which failed to enforce the selected egress port(s).
Fix this by updating the TX CPU TAG to set `FWD_TYPE` correctly, ensuring
that locally generated packets are transmitted only on the intended
port(s).
Signed-off-by: Issam Hamdi <ih@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19802
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Product name: Acer Predator Connect W6x
Product link: https://www.acer.com/us-en/predator/networking/wi-fi/predator-connect-w6x/pdp/FF.G2TTA.001
* Specifications:
SOC: MT7986AV
RAM: 1024MB
Flash: 256 MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976GN + MT7976AN
LED: 1, ws2812b controller
* Installation via UART:
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-acer_predator-w6x-initramfs-kernel.bin` to TFTP root and rename to `predator.bin`
2. Interrupt boot by pressing 0 on startup or select `U-Boot Console` in U-Boot Boot Menu.
3. Run setenv `serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr); fdt rm /signature; bootm` in uboot console.
4. Wait for boot complete on Openwrt initramfs env.
** You can back up the MTD partitions at this point. Refer to Backup Instructions section.
5. On client PC, transfer `openwrt-mediatek-filogic-acer_predator-w6x-squashfs-sysupgrade.bin` to /tmp/ - `scp -O openwrt-mediatek-filogic-acer_predator-w6x-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/sysupgrade.bin`
6. On router, run sysupgrade - `sysupgrade -n /tmp/sysupgrade.bin`
Should now boot to Openwrt. Ensure it boots automatically to Openwrt by replugging the power.
* Backup Instructions:
Layout from stock firmware:
```
[ 0.968731] Creating 10 MTD partitions on "nmbm_spim_nand":
[ 0.974297] 0x000000000000-0x000000100000 : "BL2"
[ 0.979424] 0x000000100000-0x000000180000 : "u-boot-env"
[ 0.985032] 0x000000180000-0x000000380000 : "Factory"
[ 0.990379] 0x000000380000-0x000000580000 : "FIP"
[ 0.995378] 0x000000580000-0x000000600000 : "prod"
[ 1.000461] 0x000000600000-0x000000700000 : "dual"
[ 1.005527] 0x000000700000-0x000000800000 : "pot"
[ 1.010516] 0x000000800000-0x000006c00000 : "ubi"
[ 1.015626] 0x000006c00000-0x00000d000000 : "ubi1"
[ 1.020801] 0x00000d000000-0x00000d800000 : "storage"
```
Mapping in initramfs env:
```
dev: size erasesize name
mtd0: 00100000 00020000 "bl2"
mtd1: 00080000 00020000 "u-boot-env"
mtd2: 00200000 00020000 "factory"
mtd3: 00200000 00020000 "fip"
mtd4: 00020000 00020000 "prod"
mtd5: 00100000 00020000 "dual"
mtd6: 00100000 00020000 "pot"
mtd7: 06400000 00020000 "ubi"
mtd8: 06400000 00020000 "ubi1"
mtd9: 00800000 00020000 "storage"
```
1. While in openwrt initramfs environment, back up all the partitions by running the following:
```
cat /dev/mtd0 > /tmp/bl2.bin
cat /dev/mtd1 > /tmp/u-boot-env.bin
cat /dev/mtd2 > /tmp/factgory.bin
cat /dev/mtd3 > /tmp/fip.bin
cat /dev/mtd4 > /tmp/prod.bin
cat /dev/mtd5 > /tmp/dual.bin
cat /dev/mtd6 > /tmp/pot.bin
cat /dev/mtd7 > /tmp/ubi.bin
cat /dev/mtd8 > /tmp/ubi1.bin
cat /dev/mtd9 > /tmp/storage.bin
```
2. Transfer files to client PC for safekeeping. On client PC, run `scp -O root@192.168.1.1:/tmp/*.bin ./`
* Restore to Stock Firmware:
1. Boot to openwrt initramfs env.
2. Confirm layout matches as follows by running `cat /proc/mtd`. Ensure dev `mtd7` is named `ubi`:
```
dev: size erasesize name
mtd0: 00100000 00020000 "bl2"
mtd1: 00080000 00020000 "u-boot-env"
mtd2: 00200000 00020000 "factory"
mtd3: 00200000 00020000 "fip"
mtd4: 00020000 00020000 "prod"
mtd5: 00100000 00020000 "dual"
mtd6: 00100000 00020000 "pot"
mtd7: 06400000 00020000 "ubi"
mtd8: 06400000 00020000 "ubi1"
mtd9: 00800000 00020000 "storage"
```
3. Detach `ubi` partition - `ubidetach -p /dev/mtd7`
4. Transfer stock firmware's `ubi.bin` to router from client PC: `scp -O ubi.bin root@192.168.1.1/tmp/`
5. Format and replace with backup `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
6. Reboot and you should now be back on stock firmware.
* LEDS:
LED color can be controlled by specifying values in GRB format in `/sys/class/leds/rgb:status/multi_intensity`. Default is `255 255 255` (white).
Example: `echo '75 0 130' > /sys/class/leds/rgb:status/multi_intensity`
LED brightness can be changed by specifying the value from 0-255 in /sys/class/leds/rgb:status/brightness. Default is `255` (full brightness).
Example: `echo 100 > /sys/class/leds/rgb:status/brightness`
For persistence across reboots, put the relevant command(s) in /etc/rc.local.
* Notes:
root access on stock firmware:
Before flashing openwrt, and while in openwrt initramfs env:
1. Mount /dev/ubi0_2: `mkdir /tmp/ubi0_2; mount -t ubifs /dev/ubi0_2 /tmp/ubi0_2`
2. Modify `/tmp/ubi0_2/upper/etc/passwd` and change line with `root❌0:0...` to `root::0:0...`, remove the `x`.
3. Save and reboot.
4. You should now be able to log in with root and empty password while booted in stock firmware.
While on Openwrt, subsequent upgrades can be made by sysupgrade, or via Luci. UART should not be necessary unless you want to revert to stock firmeware.
Signed-off-by: Qing W <ses1er@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
XikeStor (Seeker) SKS8310-8X is a 8 ports Multi-Gig switch, based on
RTL9303.
Specifications:
- SoC : Realtek RTL9303
- RAM : DDR3 512 MiB
- Flash : SPI-NOR 32 MiB (Macronix)
- Ethernet : 8x 1/2.5/10 Gbps (SFP+)
- LEDs/Keys (GPIO) : 1x/1x
- UART : "Console" port on the front panel
- type : RS-232C
- connector : RJ-45
- settings : 115200 8N1
- Power : 12 VDC, 2 A
Flash instruction using initramfs image:
1. Prepare TFTP server & connect to serial port.
2. Connect your computer to one of the ports on SKS8310-8X with a
suitable SFP module (some work, some don't).
3. Power on SKS8310-8X and interrupt autoboot with Shift + A.
4. Use Shift + Q to drop from vendor CLI to U-Boot CLI.
5. Enable networking within U-Boot.
> rtk network on
6. Set switch IP and TFTP server IP (optional, adjust to your setup).
> setenv ipaddr <ip>
> setenv serverip <ip>
7. Download initramfs image from TFTP server.
> tftpboot 0x82000000 <image name>
8. Boot with the downloaded image.
> bootm 0x82000000
9. With rambooted OpenWrt, backup the stock firmware if needed.
10. Copy sysupgrade image to the device.
11. Perform sysupgrade with the sysupgrade image.
12. After reboot, you should have functional OpenWrt.
Reverting to stock firmware:
1. Download latest firmware from XikeStor and upload to your device.
1. Write firmware with 'sysupgrade -F'.
2. After reboot, stock firmware should boot automatically.
Co-authored-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19782
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes 5ghz WiFi work out of the box on these devices, eliminating
the need to flash a magic blob to the radio partition.
This was found by user BulldozerBSG on the OpenWRT Forums:
https://forum.openwrt.org/t/tp-link-archer-mr600-exploration/65489/20
All credit belongs to them. I can confirm the correctness of the
findings. At least one other user (Iggy87100) confirmed them too.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19790
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The 6.12 kernel has exceeded the kernel size limit. the buildbot
can no longer build images for them. Developers can try switching
the kernel type to zImage to enable them again.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19826
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Andre Heider <a.heider@gmail.com>
Whilst testing Hasivo s1100wp-8gt-se LED configuration, several error
messages were presented which didn't indicate which led_set they were
referencing, nor what the value was that caused the invalid configuration.
Migrate to use dev_ print messages for this function.
And tidy up both when the error message is reported (don't show it when
an led_set isn't in the DTS) and what details the message presents.
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add defines for RTL930x and RTL931x led_set 'modes' (to avoid magic numbers
in dts files).
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove old kernel support to prepare for the next LTS release.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19821
Signed-off-by: Nick Hainke <vincent@systemli.org>
We have not received any negative feedback in the past three months.
It's time to switch the default kernel to 6.12.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19821
Signed-off-by: Nick Hainke <vincent@systemli.org>
All of this uses OF now. No need to keep platform data around.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19804
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit repeats the mdio function relocation from the other targets.
In short that means:
- phy read/write functions are moved away from the phy driver
- SerDes read/write functions are moved away from the dsa driver
- All gets consolidated into the mdio driver (inside the ethernet driver)
This is mostly a copy/paste to keep the changes small. The SerDes phy mapping
and the simplification of the central bus functions will come later.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19743
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IPQ4019 datasheet indicates that the maximum supported SPI
frequency is 25 MHz. My experiment on SKSpruce WIA3300-20 shows
that exceeding this threshold can lead to instability of SPI
peripheral. Limit the SPI clock frequency to the QSDK recommended
value 24MHz to enhance stability.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19744
Signed-off-by: Robert Marko <robimarko@gmail.com>
The support is done. Let's set 6.12 as testing kernel.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19771
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that the driver has been enhanced for RTL931x devices and
the DTS is up to date, activate the needed kernel configuration
for the two RTL931x subtargets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL8231 auxiliary controller is not defined in the rtl931x.dtsi.
Additionally the pinmux is configured at the wrong address. Fix
this.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The auxiliary RTL8231 controller driver is missing RTL931x support.
Add it by defining the proper register and matching compatible.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Realtek DTS's use several macros for convenient phy/port definition.
These are repeated for the RTL83xx targets and most are missing for the
RTL93xx targets. In the near future we want to add high port count
switches with 1GBit Ethernet for them too. As a preparation provide a
central include so the definition is only needed once and is available
for all targets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since 6.12 is now default, drop 6.6 support.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19778
Signed-off-by: Nick Hainke <vincent@systemli.org>
Let's switch the ipq40xx target to use kernel 6.12 by default.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19778
Signed-off-by: Nick Hainke <vincent@systemli.org>
We are using upstream otto timer. Delete some downstream leftovers.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19769
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop our downstream driver in favor of an upstream existing driver which
is available starting from v6.13.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adapt the device tree definitions of rtl93xx devices and the base dtsi
for rtl930x and rtl931x to match with what's expected by the recently
backported RTL9300 I2C driver.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport/add all patches for the upstream RTL9300 I2C driver.
The upstream driver was added in 6.13 and was heavily based on our
downstream driver except for how the multiplexing behaviour is handled.
This driver was working fine with basic SFP operation on RTL930x devices
but there was no support for RTL931x though.
Major advantage over our downstream driver is: The multiplexing
behaviour is handled completely by the driver. Thus, there's no need for
a separate rtl9300-mux driver as we had it downstream. Moreover, this
simplifies the DTS of affected devices a lot since we can now move the
controller definition - which is in the DTS of each device so far - to
the base DTSI.
Currently pending patches are also included because the progress on
getting this upstream seems really slow right now, albeit upstream
maintainers may require several changes to the current state.
These include:
- patches fixing several issues in the driver
- patches doing a refactoring of the driver and adding support for RTL931x
See the commit messages included in each patch to have details on the
changes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19736
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the conversion to dts, qca,led-pin was used for both interfaces.
Unfortunately, it's mutually exclusive with gpio-controller which made
it not do anything.
Fixes: 949e1a0 ("mpc85xx: tl-wdr4900: move platform code to dts")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19758
Signed-off-by: Robert Marko <robimarko@gmail.com>
Modernize the target slightly to use kernel+dtb FIT images in all
subtargets. LZMA compression will be used for the cortexa53 devices,
and we'll stay conservative and use gzip for the cortexa7/a8 devices
due to performance differences.
Tested-on:
- Linksprite pcDuino v2 (cortexa8 / A10)
- Olinuxino Micro (cortexa7 / A20)
- Banana Pi M2 Berry (cortexa7 / V40)
- Banana Pi P2 Zero (cortexa7 / H2+)
- Xunlong Orange Pi 2 (cortexa7/ H3)
- OrangePi PC Zero 2 (cortexa53 / H616)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This fixes intermittent dmesg errors
"nss_port5_rx_clk_src: rcg didn't update its configuration."
Signed-off-by: Marko Mäkelä <marko.makela@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/19620
Signed-off-by: Robert Marko <robimarko@gmail.com>
While checking setup routines for stability and completeness,
random RTL838x SoC I/O areas were intentionally overwritten.
As soon as L2_CTRL_1->FAST_AGE_OUT is set to 1, the system
stalls during bootup. Analysis shows that it loops endlessly
in rtl838x_hw_stop()
/* Flush L2 address cache */
if (priv->family_id == RTL8380_FAMILY_ID) {
for (int i = 0; i <= priv->cpu_port; i++) {
sw_w32(1 << 26 | 1 << 23 | i << 5, priv->r->l2_tbl_flush_ctrl);
do { } while (sw_r32(priv->r->l2_tbl_flush_ctrl) & (1 << 26));
}
This is exactly the same logic as in the vendor GPL. There
are no hints about possible timeouts or issues. The reason is
still unclear. Nevertheless harden the function for further fuzzy
tests. Do this by resetting the configuration value to its SoC
default.
Additionally convert some shifts to BIT() for better readability.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19679
Signed-off-by: Robert Marko <robimarko@gmail.com>
`loglevel=8` causes the kernel to output all logs, including debug logs, at boot time
It is enabled by default on the upstream eval board because it is aimed at developer debugging.
Most devices reference the eval board directly without modification, and the debug log should be hidden at release
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19714
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bootloader on these devices uses 0x81000000 as load address for the
compressed image. Since the kernel uses a load address 0x80100000, this
only leaves a space of 15 MiB for the uncompressed image. For larger
images, the compressed data starts to get overwritten, and at some point
the boot will fail:
## Booting image from partition ... 0
## Booting kernel from Legacy Image at 81000000 ...
Version: 9.9.9.9
Created: 2025-08-07 14:56:09 UTC
Data Size: 6756645 Bytes = 6.4 MB
Checksum ... OK
Uncompressing ... LZMA: uncompress or overwrite error 1 - must RESET board to recover
Currently, initramfs images with default config are already over the
limit. And while they still happen to work regardless, adding additional
packages easily pushes the size so much that the boot fails.
Fix this by switching to rt-loader (which relocates the data to the
upper end of the RAM before decompression). The switch includes regular
kernel images to avoid this becoming an issue again in the future.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19734
Signed-off-by: Robert Marko <robimarko@gmail.com>
Once tested this will go upstream.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19468
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previous implementation was directly copied from rtl930x and was not
working. Table field offsets are different between rlt931x and rtl930x
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add usb_vbus ref to usb device.
Signed-off-by: Andrey Safonov <andrey.safonov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19698
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add fixed regulator for M.2 slot for Bananapi BPI-RV2
Signed-off-by: Andrey Safonov <andrey.safonov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19697
Signed-off-by: Robert Marko <robimarko@gmail.com>
The .rma_bpdu_fld_pmask is not used anywhere in the code for RTL930x nor
RTL931x. But the RTL930x was still initializing this member. To avoid
problems in the future, simply initialize it also on RTL931x.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19569
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Neither the RTL930x not the RT931x use the BPDU flooding mechanism which
was used for other SoCs. At the same time, the RTL931x must use the same
debugfs initialization function as RTL930x.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19569
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit renames the network ports of the Minisforum MS-A2
Mini PC: the two 2.5G RJ45 ports are now named lan1 and lan2,
and the two 10G SFP+ ports sfp1 and sfp2.
All four ports are also added to the default lan interface.
--- Hardware Highlights ---
AMD Ryzen™ 9 9955HX/7945HX
Dual DDR5-5600MHz, up to 96GB
2x 10G SFP+, 2x 2.5G RJ45
WiFi 6E, Bluetooth 5.3
Built-in PCIe x16 Slot
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/19689
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL930x mdio functions are scattered around the code. Relocate
them to the bus (still inside the ethernet driver). With this change
the phy identification looks into the proper registers. The SerDes
phy identifier (register 2/3) must be changed.
Additionally provide a consistent SerDes register access through the
mdio bus. Until now when a SerDes directly drives a SFP module there
is no clear rule of how to handle its register set that consists of
two parts:
- c22 phy registers 0-15 live in the fiber page (2) of the SerDes
- other SerDes specific registers exist in pages before and after
The mdio bus and other SerDes functions are a wild mix of directly
looking into page 2 or just using self defined methods to access
data.
Adapt the bus to the new consistent phy interface that mixes the
SerDes register set like classic Realtek phys do it.
- Use register 31 as page select (already in the bus)
- Always keep the common registers 0-15 in place and read fiber page
- Map the SerDes internal registers into the upper vendor specific
registers 16-23 according to the page select register (31).
That gives a register mapping as follows:
+-----------------------+-----------------------+---------------+-------------+
| reg 0x00-0x0f | reg 0x10-0x17 | reg 0x18-0x1e | reg 0x1f |
+-----------------------+-----------------------+---------------+-------------+
| SerDes fiber page (3) | real SerDes registers | zero | SerDes page |
| registers 0 - 15 | in packages of 8 | | select reg |
+-----------------------+-----------------------+---------------+-------------+
Example to make it as clear as possible.
SerDes registers on a RTL930x show
Page / Reg | 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B ...
-------------+----------------------------------------------------------------
0 - SDS | 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248 0000 0F80 0000 ...
1 - SDS_EXT | 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA 8C64 00C3 1482 ...
2 - FIB | 1140 6189 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
3 - FIB_EXT | 1140 6109 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
This translates to this phy layout
| SerDes fiber registers normal SerDes registers zero p.sel
Page / Reg | 0x00 0x01 0x02 0x03 ... 0x10 0x11 0x12 0x13 ... 0x18 ... 0x1f
-------------+---------------------------------------------------------------
0 | 1140 6189 001C CA40 ... 0C03 0F00 7060 7106 ... 0000 ... 0000
1 | 1140 6189 001C CA40 ... 5248 0000 0F80 0000 ... 0000 ... 0001
...
4 | 1140 6189 001C CA40 ... 0000 0000 85FA 8C6D ... 0000 ... 0004
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19692
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some known RTL93xx devices like the Linksys LGS328C or LGS352C are
NAND based. These require additional drivers and packages (e.g. UBI).
The current subtargets are already taylored down for devices with
only 16MB flash. Adding features that are not used will only make
the storage situation more complicated.
Add two new subtargets for RTL93xx that include the basic NAND, UBI
and MTD features. To achieve this do the following:
- Create new subtarget folders
- Copy the existing config and makefiles over
- Add the basic additional features
- Mark them as SOURCE-ONLY
- Add empty image makefiles
- Remove unneded NAND/MTD features from existing configs
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19700
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devices need a tiny (<8MB) initramfs. There are first
occurrences where this fails with newer kernels and diagnostic
packages.
Switch the recipe over to use lzma compression and rt-loader.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19687
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628NN
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN [slot not install], 1x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only [antenna not install]
- LED:
System/Power (RUN): GPIO/37 active-low
Modem: GPIO/3 active-low
RF (Modem Signal): GPIO/2 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- Serial / COM: 1X RS232/RS485 on board (GPIO/6 hi:RS485 lo:RS232)
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- PCIe: 1x miniPCIe for modem [slot not install]
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 192.168.8.1 with root password "superzxmn" (SSH Port 22, Telnet Port 5188)
3. Download openwrt firmware on the computer.
4. Use scp or sftp put firmware to board /tmp
5. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h7920-v40-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h7920-v40-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17726
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CreatLentem CLT-R30B1 is a wireless WiFi 6 router.
This device uses the CLT-R30B1_0824_V1.1 board
shared by EDUP RT2980, Dragonglass DXG21,
and other diamond-shaped 5-antenna routers.
Specification
-------------
- SoC : MediaTek MT7981B dual-core ARM Cortex-A53 1.3 GHz
- RAM : DDR3 256 MiB
- Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MU-MIMO (2x 5 dBi antennas)
- 5 GHz : a/n/ac/ax, MU-MIMO (3x 5 dBi antennas)
- Ethernet :
- LAN x3 : 10/100/1000 Mbps (MediaTek MT7531AE)
- WAN x1 : 10/100/1000 Mbps (MT7981 internal PHY)
- UART : through-hole on PCB
- assignment : (RX), (TX), (GND), [3.3V]
- settings : 115200n8
- Buttons x2 : Mesh/WPS, Reset
- LEDs x2 : Status (Red, Green)
- Power : 12 VDC, 1 A, 2.1*5.5 mm
Important notes
---------------
The device is supplied in two variants.
The main difference is the size of the mtd5 (ubi)
partition in the flash layout: 64M or 112M.
112M version: Has ImmortalWrt firmware installed with LuCI WebUI.
64M version: Has stock firmware based on OpenWrt,
with the WaveLink/GL.iNet WebUI and older U-Boot
compared to the 112M version.
Flash instructions for 112M version
-----------------------------------
Follow the standard OpenWrt sysupgrade procedure without saving data.
Use the clt-r30b1-112m-squashfs-sysupgrade.bin image.
All checks should pass - don't proceed if a "not supported"
warning is issued.
Flash instructions for 64M version
----------------------------------
WebUI Method:
1. Prepare the upgrade image with clt-r30b1-squashfs-sysupgrade.bin
using the script: make_staged_upgrade_tar.sh
or use the prepared image: staged_openwrt_upgrade.bin
Downloaded from:
https://github.com/andros-ua/owrt-misc/tree/main/clt-r30b1
2. Install the prepared image using the stock WebUI update page.
3. Press and hold the reset button after reboot
to wipe the stock config and gain access.
SSH Method:
1. Connect via SSH using dg:ivanlee credentials.
2. Upload the clt-r30b1-squashfs-sysupgrade.bin image.
3. Use the command: sysupgrade -n
All checks should pass - don't proceed if a "not supported"
warning is issued.
Return to stock
---------------
Flash a backup of the ubi mtdblock (mtd5)
using the OpenWrt sysupgrade method.
Recovery
--------
Both variants:
Connect UART and use the U-Boot menu to flash the firmware image
or boot an OpenWrt initramfs image.
112M with newer U-Boot:
Power on the router while pressing the mesh button for 3 seconds.
The U-Boot Flash WebUI will be available at http://192.168.1.1
MAC Addresses:
-------------------------------------------------------
| Interface | MAC | Source |
---------------|-------------------|-------------------
| LAN | B4:4D:43:D1:xx:xx | Factory, 0x2A |
| WAN | B4:4D:43:D1:xx:xx | Factory, 0x24 |
| WLAN 2.4 GHz | B4:4D:43:D2:xx:xx | Factory, 0x4 |
| WLAN 5 GHz | B4:4D:43:D2:xx:xx | Factory, 0x4 + 1 |
-------------------------------------------------------
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19534
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The current variables tagged_ports and untagged_ports suggest that
these are distinct and describe only the ports in each of these
configuration types.
That is wrong. The hardware is configured via member ports and
untagged ports. The first one being a superset of the second.
Rename the variables to reflect that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19684
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both RTL930x and RTL931x were missing the code to support enabling and
disabling MAC address learning and unknown unicast flooding on a per-port
basis.
* rtl93*x_enable_learning() allows toggling of dynamic MAC learning on
individual ports by modifying the L2 learning constraint control
register.
* rtl93*x_enable_flood() provides the ability to control unknown unicast
flooding behavior, disabling forwarding when set. If it is enabled, it
will just forward it. If it is disabled, packets will simply be dropped.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 256MB DDR3
- FLASH: 128MB SPI-NAND WinBond W25N01GVZEIG
- NETWORK: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 3x WAN/LAN (green) 2x STATUS (red/blue)
- USB: 1x XHCI
Installation via Webinterface
-----------------------------
1. Rename OpenWrt sysupgrade bin to wavlink_wl-wn551X3-squashfs-sysupgrade.bin
The uppercase chars 551X3 are essential and checked by web interface.
2. Logon to webinterface
3. Go to network configuration -> mode selection
4. Choose mode "LAN bridge/access point"
5. Save configuration (maybe network reconfig needed)
6. Go to system upgrade
7. Choose local upgrade and provide renamed sysupgrade file
8. Start upgrade and wait for completion
9. Logon to OpenWrt (network config is preserved during upgrade)
Boot initramfs via TFTP & console
---------------------------------
1. Connect switch to network via LAN1 or LAN2
2. Power on switch
3. Press ESC until prompt reached "MT7981>"
4. Set own IP "setenv ipaddr 192.168.x.y"
5. Set TFTP IP "setenv serverip 192.168.a.b"
6. Set memory address "setenv loadaddr 0x46000000"
7. Download image "tftpboot openwrt-mediatek-filogic-wavlink_wl-wn551x3-initramfs.itb"
8. Boot image "bootm"
Notes
-----
- The red/blue LEDs give a background illumination to the top of the
case. The red LED is totally disabled to avoid noisy blinking.
- Aside from the design and the different LED colors & placements
the hardware and partitioning matches the WAVLINK WL-WN586X3 Rev B.
Therefor a common DTSI was prepared.
MAC Addresses (same as stock)
-----------------------------
LAN : 80:3F:5D:xx:xx:B1 (hw, 0x44e(text))
WAN : 80:3F:5D:xx:xx:B2 (hw, 0x460(text))
2.4GHz: 80:3F:5D:xx:xx:B1 (Factory, 0x4 (hex))
5GHz : driver auto generated
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19515
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Define MSM430 as alternative name, to explicitly show the device is
supported using existing image (MSM460).
I can confirm that the guide from
https://github.com/blocktrron/msm460-flashing works perfectly fine with
the HP MSM430 as well.
In fact, the MSM430 running the original firmware operates as
a 2x3:2 access point, but after flashing it with OpenWRT, it functions
as a 3x3:3 access point — just like the MSM460 model.
It seems that the MSM430 is essentially the same hardware as the MSM460,
with limitations imposed by the original (HP) software.
Signed-off-by: Jan Taczanowski <jan.taczanowski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19540
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for a dual-band AC1200 wall plug
manufactured by Shenzhen Century Xinyang Tech Co., Ltd.
SoC: Mediatek MT7628AN (MIPS 24KEc single core, 580 MHz)
RAM: 128 MiB DDR2 (Hynix HY5PS1G1631C)
ROM: 8 MiB SPI NOR (Zbit ZB25VQ64ASIG)
Wired: one FE RJ45 port (+ an unpopulated footprint for a 2nd)
WiFi: Mediatek MT7612E
Ant.: four 2 dBi external antennas (two 2.4GHz, two 5 GHz)
LEDs: - Power (green, always on)
- 2.4G (green, controlled by MT7628)
- 5G (green, controlled by MT7612)
- Extender (green, GPIO 37, used as status LED)
- LAN (green/yellow, controlled by RT3050 ESW)
Buttons: WPS and reset (both connected to GPIO 38)
Power: 5V 2-pin JST-XH on main PCB
110/220V AC to 5V 1.5A DC on auxiliary PCB
UART: 57600 8n1 3.3v, holes available on the PCB as J5
pinout is (Gnd) (Tx) (Rx)
MAC: 1C:BF:CE:xx:xx:xx (2.4 GHz, label)
1C:BF:CE:xx:xx:xx + 1 (LAN)
1C:BF:CE:xx:xx:xx + 2 (WAN, not in use)
1C:BF:CE:xx:xx:xx + 3 (5 GHz)
Original firmware is Chaos Calmer 15.05.01 (kernel 3.10.108)
with a few custom packages and a non-LuCI web interface.
Telnet is enabled, requiring an unknown root password [1].
Root password is also needed to access the router via UART console,
but passwordless telnet can be enabled via a trivial web exploit [2]
and then the root password can be removed by editing `/etc/shadow`.
Installation: Upload `sysupgrade` binary via web interface at
`http://192.168.188.1/settings.shtml`. Alternatively, remove
root password and use u-boot menu to flash image via TFTP.
Notes:
- Device model in Chaos Calmer is "mtk-apsoc-demo".
- It is sold under several brands, e.g., Fenvi and Linkavenir.
It is available in two colors: white and black.
- PCB is marked "WD206AD v1.0".
- Instead of a standard ethernet transformer, the PCB has a few tiny
SMD coils.
- The housing is identical to the one used by a 2020 model,
WD-R1203U, which is RTL8812-based. The older model has an FCC
listing with external and internal images: ZNPWD-R1203U.
The FCC listing contains a letter [3] claiming WD-R1203U and
WD-R1208U are internally identical, but evidently they are not.
[1] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7:::
This is the same hash as in Wodesys WD-R1802U.
There are other root password hashes in `/etc/shadow_sf` and
`/etc/shadow_yn`.
[2] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh"
[3] https://fcc.report/FCC-ID/ZNPWD-R1203U/4767033
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19535
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mach-rtl83xx.h contained the required register definitions for older SoC
families but was missing it for RTL930x and RTL931x.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19574
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Each MBR ctrl block has 64 bits to store the 56 possible ports. The offsets
between the groups is therefore also 64 bit.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19574
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The comment incorrectly stated that RTL931X doesn't have smi_poll_ctrl. But
there is actually a register for using it.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19574
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some of the parameters added to RTL9300_FAMILY_ID are missing for
RTL9310_FAMILY_ID. Simply add the missing ones to keep sharing code between
the two SoCs.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19574
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* In RTL931x, bit 31 of the (4th column) of 802_1Q_VLAN_QINQ table
indicates the validity of l2 tunnel. Before bit 63 (3rd column)
was being checked for validity of l2 tunnel.
* The untagged_ports requires 64 bits to represent 56 ports. Do not
store u64 in u32 variable
* First 24 ports are represented in the 2nd register not just first 20
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19576
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenFi 6C is a portable Wi-Fi 6 travel router based on MediaTek MT7981B+MT7976CN.
Two slightly different versions have been sold. The V1 board has a green color and lacks the modem LED. The V2 board is black and has a LED for the modem. The firmware should work on both of them.
Specifications:
- SoC: MediaTek MT7981B (Filogic 820) 1.3GHz dual-core ARM Cortex-A53
- RAM: 1GB DDR4
- Flash: 256MB SPI NAND
- Wireless: 2.4GHz/5GHz 802.11ax
- Ethernet: 1x 10/100/1000M LAN
- USB: 1x USB 3.0 Type-A port
- Expansion: M.2 slot for 5G modem
- Cooling: PWM-controlled fan
- Buttons: Reset, Mode switch
- LEDs: System, Ethernet, 5G WiFi, Modem status
**Installation via U-Boot web page**
1. Set static IP 192.168.21.2/255.255.255.0 on your computer.
2. Connect to the Ethernet port and hold the reset button while booting the device. Wait for 6-8 seconds, and release the reset button.
3. Open U-boot web page on your browser at http://192.168.21.1
4. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
5. Wait for automatic reboot.
**Installation via sysupgrade**
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Jiasheng Zhu <newbanyaya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19512
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SIM SIMAX1800U has the similar hardware design as the SIMAX1800T. The
only difference is the Ethernet portmap.
Specification
-------------
- SoC : Mediatek MT7621
- RAM : 256 MiB DDR3
- Flash : 128 MiB NAND Flash
- WLAN : Mediatek MT7905 DBDC
- 2.4 GHz : 2x2 MIMO WiFi6
- 5 GHz : 2x2 MIMO WiFi6
- Ethernet : MT7621 built-in 10/100/1000 Mbps 1x WAN; 3x LAN
- UART : 3.3V, 115200n8
- Buttons : 1x RESET; 1x WPS/MESH
- LEDs : 1x Multi-Color(Blue;Green;Red)
- Power : DC 12V1A
- CMIIT ID : 2022AP7163
- TFTP IP :
- server : 192.168.1.254
- router : 192.168.1.28
TFTP Installation(recommend)
------------
1. Set local tftp server IP "192.168.1.254" and NetMask "255.255.255.0".
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. tftpd64 is a good choice for Windows.
3. Remove all Ethernet cables and WiFi connections from the PC, except
for the one connected to the SIMAX1800U. Start the TFTP server, plug
in the power adapter and wait for the OpenWrt system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin". We need
it to back to the stock firmware.
5. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation
------------
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Return to Stock Firmware
----------------------------
Restore the backup firmware partition in the installation step 4.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LABEL | 98:xx:xx:xx:xx:b2 |
| LAN | 98:xx:xx:xx:xx:b5 |
| WAN | 98:xx:xx:xx:xx:b2 |
| WLAN2G | 98:xx:xx:xx:xx:b4 |
| WLAN5G | 9a:xx:xx:xx:xx:b4 |
+---------+-------------------+
Tips:
-----------
User can use `TFTP Installation` method to recover a brick device.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19455
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The vendor DTS defined incorrect GPIOs for the LEDs, which caused them
to not function properly. Initially, the WAN, WLAN LEDs appeared to
work, but further testing showed that they were non-functional.
This patch corrects the GPIO assignments in the DTS, restoring full LED
functionality including blinking, except the power LED which cannot be
software controlled.
Tested on a CF-EW71 v2 unit.
Fixes: ee3a6adc6c ("ath79: add support for Comfast CF-EW71 v2")
Signed-off-by: Felix Golatofski <git@xdfr.de>
Link: https://github.com/openwrt/openwrt/pull/19665
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The workqueue items don't need to be processed directly when they are
scheduled. It can happen that they are simply processed at a much later
time. It is therefore necessary to ensure that all workqueue items of a
driver are no longer being processed before the driver (or structures of
this driver) are destroyed.
When skipping this step, the driver driver can cause a kernel Oops on
reboot.
Unfortunately, it is not recommended [1] to flush items out of the system
workqueue - simply because this can cause deadlocks. The driver itself must
have a private workqueue which is then flushed.
[1] https://lkml.kernel.org/r/49925af7-78a8-a3dd-bce6-cfc02e1a9236@I-love.SAKURA.ne.jp
Signed-off-by: Issam Hamdi <ih@simonwunderlich.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19570
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just like rtl930x, rtl931x also requires two reads to fetch current link
status.
While at it, rename the function to a proper naming scheme.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Co-developed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19578
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link status needs to be read twice, and a single register value is
enough for determining link status for all the ports
It is not necessary to go through each potential port separately and later
actually identify for which ports the interrupt actually was. The helper
for_each_set_bit() directly iterate through all set bits.
While at it, rename the function to a proper naming scheme.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19578
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently the SerDes driven SFP ports give strange ethtool readings
on RTL93xx devices. Especially duplex and speed are shown even if
no link is up and running. That leads to confusion because the MAC
reports arbitrary values.
Enhance the readout by refactoring the pcs_get_state() function.
Calculate speed/duplex/pause only if link is detected.
Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19575
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The media_sts register only shows type of link, fiber/copper,
and has nothing to do with the link status
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19575
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sophos XG 210r3 is a rackmounted x86 based firewall with 6 RJ-45 gigabit
ethernet ports (eth0-5) and 2 SFP gigabit ethernet ports (eth6, eth7)
all running Intel NICs supported by igb driver. This board update maps
eth0 (left most RJ-45 port) as wan and eth1-7 as lan.
Signed-off-by: Steve Wavler <trenchcoatjedi@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19647
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We are slowly getting to the point where the mdio driver will be
carved out from the ethernet driver. Since the beginning it had
the feature to hand out SFP serdes as phys. So one can access
them from the phy driver. This will be kept during the final
migration and it even will provide a consistent interface for the
phy/serdes registers.
With this being done we need to identify how to handle the affected
ports in a generic way for all targets. Doing first things first,
this starts with a consistent DTS. Currently we have:
for RTL838x + Zyxel XGS1210:
phy-mode = "1000base-x"
managed = "in-band-status"
phy-handle = ...
for all other RTL93x devices:
phy-mode = "10gbase-r"
managed = "in-band-status"
pseudo-phy-handle = ...
Looking at the phylink kernel code one can see a nifty detail.
There is dynamic phy bringup depending on the mode.
int phylink_fwnode_phy_connect(struct phylink *pl,
const struct fwnode_handle *fwnode,
u32 flags)
{
struct fwnode_handle *phy_fwnode;
struct phy_device *phy_dev;
int ret;
/* Fixed links and 802.3z are handled without needing a PHY */
if (pl->cfg_link_an_mode == MLO_AN_FIXED ||
(pl->cfg_link_an_mode == MLO_AN_INBAND &&
phy_interface_mode_is_8023z(pl->link_interface)))
return 0;
...
}
Where 802.3z means 1000base-x or 2500base-x. Aligning this with
IEEE specs it means essentially:
- 10gbase-r defined ports with phy-handle must statically bring up
a phylink from the beginning that immediately depends on a
phy read_status() implementation.
- 1000base-x/2500base-x defined ports will dynamically bringup a
phylink during link detection regardless of a phy-handle. So
it usually runs at the moment when a SFP has been plugged in.
We currently still rely on a phy-handle but do not want to bring
up the phy immediately. Commit 4457c1eee4 ("realtek: rtl93xx:
support SFPs with phys") tried to fix exactly that error for
10gbase-r definied ports. Kernel shows "sfp sfp-p8: sfp_add_phy
failed: -EBUSY" in that case.
But it did it in the wrong way. It implemented a workaround by
introducing a DTS property "pseudo-phy-handle". Instead it
should have simply converted the DTS nodes to 1000base-x.
Revert the commit and fix the DTS with wrong definitions. From
now on we have a consistent SFP definition throughout all DTS
and targets.
Aside from the positive effect this setting has it is more or
less an arbitrary speed definition. When plugging in the SFP the
real speed will be choosen dynamically.
Fixes: 4457c1eee4 ("realtek: rtl93xx: support SFPs with phys")
Tested-By: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19648
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patches 12 and 13 have been superseded by patch 12. Other patches
have no significant changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19675
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling of both calibration and mac addresses is deprecated.
Also fixed calibration size for ath9k. AR9287 uses 3d8 for its size.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17289
Signed-off-by: Robert Marko <robimarko@gmail.com>
The current build recipe creates a lzma based initramfs and
a gzip based sysupgrade (installation) image. No need to
use different compression methods. Use lzma for both.
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19669
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add SoC revision, CPU part number, and a flag for engineering samples to
the rtl83xx_soc_info structure.
Also extend the system type string to include this information.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19653
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move the definitions to mach-rtl83xx.h, so they can be used during init
to read more detailed SoC information. Also rename the RTL931X register,
as it has the same address on all RTL93xx.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19653
Signed-off-by: Robert Marko <robimarko@gmail.com>
Read model name from the register instead of using hard-coded values.
Also remove detection of the unsupported Realtek ESW/SSW SoCs. The Fast
Ethernet variants of the Maple and Cypress series stay for now, but are
moved to the RTL8380/RTL8390 families.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19653
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the lzma recipe for the device for both initramfs and sysupgrade to
save some flash space due to smaller image. U-Boot build on this device
has native lzma support.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19657
Signed-off-by: Robert Marko <robimarko@gmail.com>
The migration of the RTL930x mdio/serdes access functions over to the
mdio bus is a little more complicated than for RTL83xx. There are several
places where the serdes is accessed directly. So do it in two steps. With
this first step:
- use the rtmdio prefix for the serdes reader/writer functions
- move the functions over to the bus (inside the ethernet driver)
- Adapt all callers.
This is not only a copy/paste but the serdes access will be hardened too.
For this:
- put a mutex around the read/write functions because we have only
indirect register access through a mdio style bus.
- Verify input values to avoid data mess.
Tested-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19662
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 6.12 is now default, drop 6.6 support.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19682
Signed-off-by: Nick Hainke <vincent@systemli.org>
Let's switch the lantiq target to use kernel 6.12 by default.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19682
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update default kernel version to 6.12 and drop configs and patches for
kernel 6.6.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/19666
Signed-off-by: Nick Hainke <vincent@systemli.org>
Like RTL839x the RTL930x SoCs have multithreading built in.
Activate it in the kernel configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19624
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL839x mdio functions are scattered around the code. Relocate
them to the bus (still inside the ethernet driver).
Additionally provide a consistent SerDes register access through the
mdio bus. Until now when a SerDes directly drives a SFP module there
is no clear rule of how to handle its register set that consists of
two parts:
- c22 phy registers 0-15 live in the fiber page (2) of the SerDes
- other SerDes specific registers exist in pages before and after
The mdio bus and other SerDes functions are a wild mix of directly
looking into page 2 or just using self defined methods to access
data.
Adapt the bus to the new consistent phy interface that mixes the
SerDes register set like classic Realtek phys do it.
- Use register 31 as page select (already in the bus)
- Always keep the common registers 0-15 in place and read fiber page
- Map the SerDes internal registers into the upper vendor specific
registers 16-23 according to the page select register (31).
That gives a register mapping as follows:
+-----------------------+-----------------------+---------------+-------------+
| reg 0x00-0x0f | reg 0x10-0x17 | reg 0x18-0x1e | reg 0x1f |
+-----------------------+-----------------------+---------------+-------------+
| SerDes fiber page (3) | real SerDes registers | zero | SerDes page |
| registers 0 - 15 | in packages of 8 | | select reg |
+-----------------------+-----------------------+---------------+-------------+
Example to make it as clear as possible.
SerDes registers on a RTL839x show
Page / Reg | 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B ...
-------------+----------------------------------------------------------------
0 - SDS | 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248 0000 0F80 0000 ...
1 - SDS_EXT | 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA 8C64 00C3 1482 ...
2 - FIB | 1140 6189 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
3 - FIB_EXT | 1140 6109 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
This translates to this phy layout
| SerDes fiber registers normal SerDes registers zero p.sel
Page / Reg | 0x00 0x01 0x02 0x03 ... 0x10 0x11 0x12 0x13 ... 0x18 ... 0x1f
-------------+---------------------------------------------------------------
0 | 1140 6189 001C CA40 ... 0C03 0F00 7060 7106 ... 0000 ... 0000
1 | 1140 6189 001C CA40 ... 5248 0000 0F80 0000 ... 0000 ... 0001
...
4 | 1140 6189 001C CA40 ... 0000 0000 85FA 8C6D ... 0000 ... 0004
...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19634
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Use SDS for phy 48/49
* Use correct link/phy settings for SFP ports
* Remove read-only flag from u-boot env so fw_setenv actually works
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/19596
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When a SerDes directly drives a SFP module there is no clear rule of
how to handle its register set that consists of two parts:
- c22 phy registers 0-15 live in the fiber page (2) of the SerDes
- other SerDes specific registers exist in pages before and after
The mdio bus and other SerDes functions are a wild mix of directly
looking into page 2 or just using self defined methods to access
data.
Provide a consistent phy interface that mixes the SerDes register
set like classic Realtek phys do it.
- Use register 31 as page select (already in the bus)
- Always keep the common registers 0-15 in place and read fiber page
- Map the SerDes internal registers into the upper vendor specific
registers 16-23 according to the page select register (31).
That gives a register mapping as follows:
+-----------------------+-----------------------+---------------+-------------+
| reg 0x00-0x0f | reg 0x10-0x17 | reg 0x18-0x1e | reg 0x1f |
+-----------------------+-----------------------+---------------+-------------+
| SerDes fiber page (3) | real SerDes registers | zero | SerDes page |
| registers 0 - 15 | in packages of 8 | | select reg |
+-----------------------+-----------------------+---------------+-------------+
Example to make it as clear as possible.
SerDes registers on a RTL838x show
Page / Reg | 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B ...
-------------+----------------------------------------------------------------
0 - SDS | 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248 0000 0F80 0000 ...
1 - SDS_EXT | 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA 8C64 00C3 1482 ...
2 - FIB | 1140 6189 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
3 - FIB_EXT | 1140 6109 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
This translates to this phy layout
| SerDes fiber registers normal SerDes registers zero p.sel
Page / Reg | 0x00 0x01 0x02 0x03 ... 0x10 0x11 0x12 0x13 ... 0x18 ... 0x1f
-------------+---------------------------------------------------------------
0 | 1140 6189 001C CA40 ... 0C03 0F00 7060 7106 ... 0000 ... 0000
1 | 1140 6189 001C CA40 ... 5248 0000 0F80 0000 ... 0000 ... 0001
...
4 | 1140 6189 001C CA40 ... 0000 0000 85FA 8C6D ... 0000 ... 0004
For now just do it for RTL838x devices.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19604
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is a variant of the Radxa ROCK Pi E v3 equipped with the Realtek
RTL8821CU. Add the kmod-rtw88-8821cu package for it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/18310
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The DSA has a link to the MDIO bus and already uses the read/write functions
that are provided. In parallel the dsa_switch_ops structure provides an
interface for phy_read and phy_write. These are still open-coded and sadly
circumvent the bus. Simplify the implementation and avoid inconsistencies by
reusing the existing bus infrastructure.
Additionally, remove two unused MMD header definitions as a quick win.
Reported-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19548
Signed-off-by: Robert Marko <robimarko@gmail.com>
The function rtl93xx_setup() is called by both RTL930x and RTL931x. But
only the RTL930x specific function to print port matrix was called.
Unfortuntaly, RTL931x needs a different function to access the correct
registers to retrieve the port matrix information.
It is therefore necessary differentiate in rtl93xx_setup between the
SoC families before calling the appropriate function.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19572
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL931x has 56 (0-55) non-CPU ports. To receive updates about the port
state, it is therefore necessary to enable the interrupts for all these
ports.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19572
Signed-off-by: Robert Marko <robimarko@gmail.com>
* traffic isolation tables are different between rtl930x and rtl931x
* traffic_enable/disable/get/set functions span multiple columns in the
rtl931x as a result, previous implementation would only enable traffic
in some ports.
traffic_enable/disable and traffic_set/get should now work on all ports and
not just the initial 32
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19572
Signed-off-by: Robert Marko <robimarko@gmail.com>
A commit which broke netdev trigger LEDs offloaded to PHYs recently made
it all the way down to the Linux 6.6 stable branch. The revert has been
accepted to linux-next, however, a backport to the various -stable trees
is still pending.
Import the backported revert commit to fix in OpenWrt in the meantime
until the revert also gets picked to linux-stable.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=26f732791f2bcab18f59c61915bbe35225f30136
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Deleted useless content, since it is the same as the mainline kernel
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19300
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove extra blank lines.
Fixes typo for label and status.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19400
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include the NAND specs into the DTS. It is unclear which devices
really need it. Keep it disabled for now. As the SoC register area
is defined too small until now, increase the size to an appropriate
value.
If enabled one can see the following log messages (e.g. Linksys
LGS328C or LGS352C).
[ 1.206600] spi-nand spi1.0: Macronix SPI NAND was found.
[ 1.212795] spi-nand spi1.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 1.222217] 3 fixed-partitions partitions found on MTD device spi1.0
[ 1.229466] OF: Bad cell count for /soc/spi@1a400/flash@0/partitions
[ 1.236617] OF: Bad cell count for /soc/spi@1a400/flash@0/partitions
[ 1.244164] Creating 3 MTD partitions on "spi1.0":
[ 1.249620] 0x000000000000-0x000004000000 : "ubifs"
[ 1.423593] 0x000004000000-0x000005e00000 : "firmware"
[ 1.738268] mtdsplit_uimage: no uImage found in "firmware"
[ 1.744577] 0x000005e00000-0x000007c00000 : "runtime2"
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19583
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL93xx devices have a NAND controller built in. Upstream already
has a driver in place. Include it downstream. Activate it in the
RTL93xx builds and disable it for the RTL83xx builds.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19583
Signed-off-by: Robert Marko <robimarko@gmail.com>
During PHY matching, the SMI polling must be disabled to avoid conflicts
during the complex detection routine. Only after this finished, SMI polling
is allowed again.
This was implemented for all realtek families besides RTL931x.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19603
Signed-off-by: Robert Marko <robimarko@gmail.com>
A RTL930x function to read the value from an SDS register must not used on
an RTL931x SoC. Doing it with rtl930x_read_sds_phy() would corrupt the
written results when only parts of the bits are written.
Fixes: 7026084066 ("realtek: Add SDS configuration routines for the RTL93XX platforms")
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19603
Signed-off-by: Robert Marko <robimarko@gmail.com>
Vimin VM-S100-0800MS is an 8 port Multi-Gig switch, based on RTL9303.
Ported from XikeStor SKS8300-8X with changes to support different u-boot
build.
Specification:
- SoC : Realtek RTL9303
- RAM : DDR3 512 MiB
- Flash : SPI-NOR 16 MiB (Winbond W25Q128JVSQ)
- Ethernet : 8x 1/2.5/10 Gbps (SFP+)
- LEDs/Keys (GPIO): 0x/1x
- UART : "Console" port on the front panel
- type : RS-232C
- connector : RJ-45
- settings : 115200n8
- Power : AC100-240V 50/60Hz
Flash instruction using initramfs image:
1. Prepare TFTP server with an IP address "192.168.1.111"
2. Connect your PC to Port1 on VM-S100-0800MS
3. Power on VM-S100-0800MS and interrupt boot by pressing Esc
4. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
7. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
8. Boot with the downloaded image
bootm
9. On the initramfs image, backup the stock firmware if needed
10. Upload (or download) sysupgrade image to the device
11. Erase "firmware" partition to cleanup JFFS2 of stock FW
mtd erase firmware
12. Perform sysupgrade with the sysupgrade image
13. Wait ~120 sec to complete flashing
Reverting to stock firmware:
1. Prepare by downloading the stock firmware. Vimin doesn't have
the firmware on their website, tested using firmware for shared
hardware Nicgiga S100-0800S-M.
Filename: vmlinux-nicgiga-S100-0800S-M-241126EN.bix
2. Prepare TFTP server with an IP address "192.168.1.111"
3. Connect your PC to Port1 on VM-S100-0800MS
4. Power on VM-S100-0800MS and interrupt boot by pressing Esc
5. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
6. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
7. Boot with the downloaded image
bootm
8. Under Management -> Firmware -> Upgrade/Backup, upload bix file.
9. Reboot device
Signed-off-by: Colton Pawielski <cepawiel@mtu.edu>
Link: https://github.com/openwrt/openwrt/pull/19477
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The tsens node had an extra space in the "okay" status string, preventing
thermal sensors from being properly registered. This patch corrects it to
enable proper thermal monitoring support.
Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
Link: https://github.com/openwrt/openwrt/pull/19564
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Hasivo S1100W-8XGT-SE switch.
Device specification
--------------------
SoC Type: RTL9303
RAM: Samsung K4B461646E-BYKO (512MB)
Flash: Fudan FM25Q128A (16 MB)
Ethernet: 8x 10G via 2x RTL8264 PHY
LEDs: 2 LEDs, 1 power green, 1 system green
Button: Reset
USB ports: None
Bootloader: Realtek U-Boot - U-Boot 2011.12.(3.6.6.55087) (Nov 13 2022 - 14:37:31)
Fan: 2 fans controlled by STC8G1K08 TSOP-20 microcontroller
Note: The fan appears to operate the same irrespective of the running
firmware. The STC9G1K08 is likely operating independently.
To explore the stock vendor firmware, there are 2 avenues to gain root
access. This is not necessary to install OpenWrt, but is here for
reference.
Root access via serial
----------------------
1. ctrl+t
2. password: switchrtk
3. press 's' for shell
Root access via SSH
-------------------
1. ctrl+t
2. password: switchrtk
3. sys command sh
4. log in with your username+password
5. ctrl+t
6. password: switchrtk
7. press 's' for shell
Credit to https://forum.openwrt.org/t/hasivo-switches/151758/174 for rooting instructions.
Installing OpenWrt
------------------
1. Connect to UART. UART requires soldering an RJ45 connector to the
console footprint on the board. The header is on the top right of
this image: 4d2ab97fad.jpeg
2. Set computer IP to 192.168.0.111.
3. Enter bootloader by pressing esc key during boot.
4. Enter password 'Hs2021cfgmg'.
5. Type 'XXXX'.
6. setenv bootcmd 'rtk network on; bootm 0xb4300000'
7. saveenv
8. rtk network on
9. tftpboot 0x84f00000 <openwrt-initramfs>
10. bootm 0x84f00000
Now you can copy over the sysupgrade image and install.
Credit to
https://forum.openwrt.org/t/hasivo-switches/151758/22?u=andrewjlamarche
for u-boot console access instructions.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17137
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since Linux 6.7, introduced with commit 5c2f7727d437 ("mtd: mtdpart:
check for subpartitions parsing result"), errors during subpartition
parsing cause all MTD partitions to be torn down.
Since the current mtdsplit driver for devices using H3C VFS returns
-EINVAL if it does not find a file system containing an OpenWrt image,
this makes initial installation of OpenWrt impossible.
Work around this by returning 0 when the file system contains unexpected
data. Also print a message in this case to show what is going on.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19475
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Maintain 64 bit counters by polling the hardware counters and adding up
the differences. Polling needs to happen just often enough to catch
every single overflow.
As we now have non-overflowing counters now, we can safely calculate
composite counters without getting weird results on overflow. Use this
to follow RFC 3635 more accurately by mapping the hardware counters to
the proper counters, while taking into account hardware quirks as best
as possible.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By default, the network interface stats are based on software counters,
which only consider traffic from and to the CPU. Implementing the
get_stats64 method allows to report the full hardware counters instead.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel offers several alternatives to get_ethtool_stats which allow
to report some stats in a more structured way. Use them where possible.
Ideally, we should follow RFC 3635 to translate the hardware counters to
the supported frame and octet counters. However, this is not feasible,
as some of the counters are 32-bit only (so it would produce incorrect
results as soon as one of them overflows).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MIB registers contain different stats depending on the SoC, and for
RTL930x some stats are in an additional register.
Create separate MIB descs for each SoC to implement this. Also make
reading 64-bit counters more robust, by protecting against an overflow
of the lower 32 bits during the read.
RTL931x remains unsupported, because it uses a table and thus requires
a separate implementation.
While we are at it, rename structs/functions to use the rtldsa prefix.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-md-multipath was removed in kernel 6.12, remove the dependency here
too.
This fixes the build of the gemini target.
Fixes: d12a603de5 ("kernel: kmod-md-multipath: Depend on kernel 6.6")
Link: https://github.com/openwrt/openwrt/pull/19532
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After observation that timer interrupt 7 always fires on secondary VPEs
the counter was disabled in the startup code. This is a bad idea when
building the kernel with jitterentropy. To generate entropy it makes use
of function random_get_entropy(). On MIPS architecture this simply reads
the counter register on the current core. With a disabled counter it
always returns the same value and the entropy initialization stalls the
core if it runs on a secondary VPE. See backtrace
[ 21.736246] rcu: INFO: rcu_sched self-detected stall on CPU
[ 21.736246] rcu: INFO: rcu_sched self-detected stall on CPU
[ 21.748594] rcu: 1-....: (2100 ticks this GP) idle=064c/1/0x40000002 softirq=7/7 fqs=1050
[ 21.748594] rcu: 1-....: (2100 ticks this GP) idle=064c/1/0x40000002 softirq=7/7 fqs=1050
[ 21.766871] rcu: (t=2102 jiffies g=-1187 q=25 ncpus=2)
[ 21.766871] rcu: (t=2102 jiffies g=-1187 q=25 ncpus=2)
[ 21.778429] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.39 #482
[ 21.778429] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.39 #482
[ 21.778461] Hardware name: Zyxel GS1900-48
[ 21.778461] Hardware name: Zyxel GS1900-48
...
[ 21.779757] [<8029b968>] jent_measure_jitter+0xc8/0x10c
[ 21.779757] [<8029b968>] jent_measure_jitter+0xc8/0x10c
[ 21.779779] [<8029b9e8>] jent_gen_entropy+0x3c/0xb0
[ 21.779779] [<8029b9e8>] jent_gen_entropy+0x3c/0xb0
[ 21.779800] [<8029bcc0>] jent_entropy_collector_alloc+0x104/0x118
[ 21.779800] [<8029bcc0>] jent_entropy_collector_alloc+0x104/0x118
[ 21.779822] [<8029bd6c>] jent_entropy_init+0x4c/0x2ec
[ 21.779822] [<8029bd6c>] jent_entropy_init+0x4c/0x2ec
[ 21.779844] [<8086f184>] jent_mod_init+0x58/0xac
[ 21.779844] [<8086f184>] jent_mod_init+0x58/0xac
[ 21.779865] [<80100200>] do_one_initcall+0x70/0x250
[ 21.779865] [<80100200>] do_one_initcall+0x70/0x250
[ 21.779883] [<8085c018>] kernel_init_freeable+0x1f0/0x280
[ 21.779883] [<8085c018>] kernel_init_freeable+0x1f0/0x280
[ 21.779905] [<8067cba4>] kernel_init+0x20/0xb0
[ 21.779905] [<8067cba4>] kernel_init+0x20/0xb0
[ 21.779926] [<80101158>] ret_from_kernel_thread+0x14/0x1c
[ 21.779926] [<80101158>] ret_from_kernel_thread+0x14/0x1c
This bit of entropy is helpful on these low end devices. Reenable the
counter and simply disable the interrupt.
Fixes: b7aab19585 ("realtek: SMP handling of R4K timer interrupts")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19499
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio bus functions are still split between ethernet and dsa driver.
Before moving everthing out to a separate mdio driver we decided to
collect everything in the ethernet driver with the rtmdio prefix.
Take over the remaining RTL838x functions.
Remark: This is more or less a copy/paste with function renaming. As
there are still some consumers in the DSA driver the definitions and
inclusions must be flipped.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19484
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently the SerDes driven SFP ports give strange ethtool readings
on RTL83xx devices. Especially duplex and speed are shown even if
no link is up and running. That leads to confusion because the MAC
reports arbitrary values.
Enhance the readout by refactoring the pcs_get_state() function.
Calculate speed/duplex/pause only if link is detected. Additionally
add reporting of 10G for SFP+ on RTL839x.
ethtool for empty SFP cage before/after
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ MII ]
Supported link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ MII ]
Supported link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
ethtool with inserted but NOT connected 1G module before/after
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19524
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows building the kmod-drm-ivpu which depends on
CONFIG_DRM_ACCEL. This module is x86_64 only.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-rpi-panel-attiny-regulator and kmod-rpi-panel-7inch-touchscreen
are included in target modules.mk file, they should also depend on the target,
otherwise they can be selected from every target.
Fix the AutoProbe for panel-raspberrypi-touchscreen too.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-imx2-wdt, kmod-imx7-ulp-wdt and kmod-wdt-sp805 are included in
target modules.mk file, they should also depend on the target, otherwise
they can be selected from every target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-ata-dwc is included in target modules.mk file, it should also
depend on the target, otherwise it can be selected from every target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_BCMGENET kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-bcmgenet depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SerDes setup function needs to be called to make 2500Base-X work.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19517
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On some devices (like ZyXEL GS1920) the phys are not initialized and patched
by the bootloader. This is done through the vendor SDK when the software
starts. To make these devices usable too, provide the most basic setup
sequence for the RTL8218B.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19491
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver currently uses two checks to verify the capabilities. These
are ..._phylink_get_caps() and ..._pcs_validate(). For RTL930x these
must allow 2.5G modes. Enhance that as follows:
Add 2500BASEX to phylink_get_caps(). Sort the interfaces alphabetically
and rename the function to the new prefix. IMPORTANT REMARK! Until now
this function allowed the XGMII mode (10G only parallel interface) that
was somehow mixed with the Realtek proprietary mode XSGMII (10G SGMII).
Remove it to avoid further confusion.
Looking upstream pcs_validate() is used less and less. There are only
2 consumers left in 6.16 and the calling location reads:
/* Validate the link parameters with the PCS */
if (pcs->ops->pcs_validate) {
ret = pcs->ops->pcs_validate(pcs, supported, state);
if (ret < 0 || phylink_is_empty_linkmode(supported))
return -EINVAL;
/* Ensure the advertising mask is a subset of the
* supported mask.
*/
linkmode_and(state->advertising, state->advertising,
supported);
}
There is no need for this additional check. Drop the functions.
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file should be generated automatically at runtime by the kernel
build system.
Link: https://github.com/openwrt/openwrt/pull/19473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix bootloop on TP-Link EAP615-Wall v1 by reducing LZMA dictionary
size. Before this patch and after an upgrade to kernel 6.12 this
device couldn't boot a kernel because of an error: "lzma compressed:
uncompress error 1".
I have chosen -d22 as dictionary size as suggested by @namiltd.
The usual sizes for problematic devices are -d16, -d20, -d22. I
have confirmed with my tests that this device can boot with a value
up to -d27, but there is no size benefit from values above -d21,
therefore -d22 is good enough.
See also: https://github.com/openwrt/openwrt/issues/19403
Signed-off-by: Marcin FM <marcin@ipv8.pl>
Link: https://github.com/openwrt/openwrt/pull/19433
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some NanoPC-T6 boards with A3A444 eMMC chips experience I/O errors and
corruption when using HS400 mode. Downgrade to HS200 mode to ensure
stable operation.
Fixes: #18844
Signed-off-by: Grzegorz Sterniczuk <grzegorz@sternicz.uk>
Link: https://github.com/openwrt/openwrt/pull/19398
[Add patch header]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit increases the SPI bus frequency from 20 to 52 MHz. Reduces boot
time by 2s. Below is a performance comparison.
Before:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 2 s, 5.8 MB/
After:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 1 s, 9.7 MB/s
Taken from PR #18752 as each device should be tested individually, so I have
created a separate PR for this.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With the switch to Linux 6.12 this driver was enabled by accident.
However, it doesn't support any of the router SoCs but is meant to be
used only by the smartphone, tablet and chromebook SoCs.
Disable the driver again to silence a kernel error logline during boot.
Fixes: 0a0f5f94ec ("mediatek: mt7623: update config-6.12")
Fixes: 029b7ed9c4 ("mediatek: mt7622: update config-6.12")
Reported-by: https://aparcar.org/openwrt-tests/119/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add new mtdsplit parser "mstc-boot" for the devices manufactured by MSTC
(Mitra Star Technology Corp.). This is necessary to handle dual-boot on
those devices.
This parser splits kernel+rootfs or only rootfs(or UBI) based on the
image in the firmware partition or pre-defined partitions in dts, and
"bootnum" value in the "persist" (or "working") partition.
Note: "bootnum" is used for switching active firmware partitions on the
devices manufactured by MSTC and '1' or '2' are used on most
devices. But some devices use '0' or '1'. (example: I-O DATA
WN-DEAX1800GR)
Sequence:
1. obtain "bootnum" value
2. child nodes exsist (regardless of bootnum)
-> fixed partitions
(active parts : without bootnum (ex.: "kernel", "rootfs")
inactive parts: with bootnum (ex.: "kernel2", "rootfs2"))
3. current partition is active (dt bootnum == mtd bootnum)
-> image-based partitions
Device Tree:
- common
- mstc,bootnum : "bootnum" value for the mtd partition (0/1/2)
- mstc,persist : phandle of "persist" partition containing "bootnum"
value
- fixed partitions
- #address-cells: indicate cell count of address of child nodes (1)
- #size-cells : indicate cell count of size of child nodes (1)
- (child nodes) : define the child partitions
- reg : define the offset and size
- label-base : define the base name of the partition
- (example) : base:"kernel"->"kernel"(active)/"kernel2"(inactive)
example:
partition@3c0000 {
compatible = "mstc,boot";
reg = <0x3c0000 0x3240000>;
label = "firmware1";
mstc,bootnum = <1>;
mstc,persist = <&mtd_persist>;
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x800000>;
label-base = "kernel";
};
partition@800000 {
reg = <0x800000 0x2a40000>;
label-base = "ubi";
};
};
- image-based partitions
(no additional properties)
example:
partition@5a0000 {
compatible = "mstc,boot";
label = "firmware1";
reg = <0x5a0000 0x3200000>;
mstc,bootnum = <1>;
mstc,persist = <&mtd_persist>;
};
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18976
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The 6.12 testing kernel for ipq40xx target is ready now.
Tested on SKSpruce WIA3300-20.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On the ipq40xx platform, the bus range is 1 - 255. Therefore, bus
number 0 is clearly incorrect. Change the bus number to 1, just
like other ipq40xx devices. This patch fixes the following dtc
warnings on 6.12 kernel:
qcom-ipq4019.dtsi:476.5-29: Warning (pci_device_bus_num): /soc/pcie@40000000/pcie@0/wifi@0,0:bus-range: PCI bus number 0 out of range, expected (1 - 255)
qcom-ipq4019.dtsi:476.5-29: Warning (pci_device_bus_num): /soc/pcie@40000000/pcie@0/wifi@0,0:bus-range: PCI bus number 0 out of range, expected (1 - 255)
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Remove duplicate PCIe bridge. A default bridge node has been
added upstream.
- Do not refer to the qca807x node. This node label has been
removed. We can disable the qca807x phy in mdio node.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a bridge node label so that we can insert PCIe peripheral nodes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Copy arch directory from 6.12 kernel to restore the default
6.6 device tree files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Copy patches and kernel configs from 6.12 kernel to restore the
default 6.6 kernel support files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for 6.12 kernel support. It can help us
track the device tree files history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for 6.12 kernel support. It can help us
track the patches and Kconfig history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for introducing the 6.12 kernel support.
All configs are automatically refreshed. In theory, they will
generate the same .config files in the kernel build directory
as before.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The prototype of `devm_platform_ioremap_resource_byname()` was defined
in `linux/platform_device.h`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This function is only used by the current source file gcc-ipq4019.c.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The node name should include the reg property value. Fix warning:
qcom-ipq4019-lbr20.dts:415.17-449.4: Warning (i2c_bus_reg): /soc/i2c@78b7000/led-controller: I2C bus unit address format error, expected "27"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The files-6.6 and files-6.12 folder contain the same content, merge them
into the files folder for both kernel versions.
Link: https://github.com/openwrt/openwrt/pull/19423
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ix4-200d is a 4 bay NAS supported since OpenWrt 23.05. Drive trays
controller. Due to a kernel-related issue with the SATA controller,
trays #1 and #2 were not recognized. This issue has been fixed in
kernel 6.10, so with the adoption of kernel 6.12 in the Kirkwood
target trays #1 and #2 can now be made accessible. This requires the
kmod-ata-ahci package, which this commit adds as default to the
makefile.
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: https://github.com/openwrt/openwrt/pull/19435
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These u-boot images are no longer automatically copied to the
bindir since commit:
ed50004319 ("uboot-mediatek: add support for Linksys E8450")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Package kernel modules for PS/2 mouse support, mostly to allow
using touchpads and trackpoints built-into laptops (many of those
are connected using classic i8052-compatible PS/2 I/O).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
pci driver went to a different directory and thus manually edited.
All else done with kernel_oldconfig.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Copy kernel config and patches from 6.12 to restore the default 6.6
kernel support files.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for 6.12 kernel support. It can help us
track the files history by using the Git tool.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL83xx devices have two types of receive interrupts for each of its
8 rings. One for packet received and another for ring overflow. When
the switch is flooded with incoming packets the receive handler will
disable the packet receive notification but still keeps the overflow
notification enabled. While the receive path "slowly" processes the
received packets each new packet triggers the overflow IRQ again. The
device becomes unresponsive and eventually produces messages like:
[18441.709764] rcu: Stack dump where RCU GP kthread last ran:
[18441.727892] Sending NMI from CPU 1 to CPUs 0:
[18441.742300] NMI backtrace for cpu 0 skipped: idling at 0x8080e994
[18415.251700] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[18415.271350] rcu: 0-...!: (0 ticks this GP) idle=d740/0/0x0 ...
[18415.303046] rcu: (detected by 1, t=6004 jiffies, g=230925, ...
[18415.326095] Sending NMI from CPU 1 to CPUs 0:
[18415.340540] NMI backtrace for cpu 0
Fix this issue by always disabling receive and overflow interrupts at
the same time.
Test with hping3 --udp -p 5021 -d 1400 --flood 192.168.2.72
Before (3sec run):
[183260.324846] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x101, mask: 0x7ffeff
[183260.340524] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x1, mask: 0x7ffeff
[183260.345799] net_ratelimit: 489997 callbacks suppressed
After (3 sec run):
[ 373.981479] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 374.031118] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 377.919996] net_ratelimit: 34 callbacks suppressed
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19365
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The current implementation has several issues:
- it uses the hacky phy_port* macros
- it uses SoC dependent raw pages
- it disables/enables SoC dependent polling
Get rid of these dependencies and access the mdio bus the normal way.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19372
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an OpenWrt-based U-Boot build for this device, allowing for more
flexibility and customization.
Expected behaviour
------------------
When plugging the device, keeping the reset button pressed will enter
TFTP recovery mode: the board will send requests for the initramfs file
(openwrt-mediatek-filogic-glinet_gl-mt2500-initramfs-kernel.bin) from
IP 192.168.1.1 to 192.168.1.10 TFTP server.
The bootloader will populate the environment with the unit serial number
as reported by the "sn" value in eMMC, the "sn_bak" value, the country
code and ddns. WAN and LAN MAC addresses are reported in the environment
as well.
Limitations
-----------
No web interface is available, and only the LAN port can be used for
system recovery.
Notes
-----
This port has been tested with the Maxlinear version only, and with a
board that does not exhibit eMMC communication problems. Even though eMMC
frequency has been lowered, some testing is probably needed and always
very welcome.
A -factory image has been introduced, and is only needed when using the
"Load Firmware via TFTP then write to eMMC." boot menu function.
The device has not been converted to use uImage.FIT including the rootfs
to keep compatibility with stock bootloader and firmware.
Installation
------------
From a Linux root shell:
0. Transfer the needed files to the board, placing them in /tmp.
1. Make sure your U-Boot environment is erased: all of my units came with
unpopulated environment, but I am not sure this is always the case.
Issue the command
cat /dev/zero >/dev/mmcblk0p2
(you will get a "no space left" error, which is reasonable and expected).
2. Unlock the eMMC boot area where BL2 is located:
echo 0 >/sys/block/mmcblk0boot0/force_ro
3. Write the new BL2 code:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-preloader.bin >/dev/mmcblk0boot0
4. Write new BL31+U-Boot image:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-bl31-uboot.fip >/dev/mmcblk0p4
5. Reboot.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
The device is equipped with a GPS module, reporting data via /dev/ttyS1.
A TF card reader is also present. Only one of those components can be
used at once, since they share some PINs.
This commit adds two devicetree overlays to allow for the user to select
the desired configuration. Another overlay configuration to allow booting
from SD card is provided.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
All kernel symbols are automatically refreshed by
`make kernel_oldconfig CONFIG_TARGET=target` and
`make kernel_oldconfig CONFIG_TARGET=subtarget`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
* Drop obsolete flag I2C_CLASS_SPD. [1]
* Change .remove callback return type to NULL.
* Use strscpy instead of strlcpy.
This patch fixes the following build errors:
drivers/i2c/busses/i2c-lantiq.c:599:41: error: 'I2C_CLASS_SPD' undeclared (first use in this function); did you mean 'I2C_CLASS_HWMON'?
599 | adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
| ^~~~~~~~~~~~~
| I2C_CLASS_HWMON
drivers/i2c/busses/i2c-lantiq.c:600:9: error: implicit declaration of function 'strlcpy'; did you mean 'strncpy'? [-Wimplicit-function-declaration]
600 | strlcpy(adap->name, DRV_NAME "-adapter", sizeof(adap->name));
| ^~~~~~~
| strncpy
drivers/i2c/busses/i2c-lantiq.c:729:19: error: initialization of 'void (*)(struct platform_device *)' from incompatible pointer type 'int (*)(struct platform_device *)' [-Wincompatible-pointer-types]
729 | .remove = ltq_i2c_remove,
|
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.12.y&id=e61bcf42d290e73025bab38e0e55a5586c2d8ad5
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This is a preparation for 6.12 kernel support. It can help us
track the files history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This is a preparation for introducing the 6.12 kernel support.
All configs are automatically refreshed.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/lantiq/xway/vmmc.c:31:14: error: no previous prototype for 'ltq_get_mps_ad0_irq' [-Werror=missing-prototypes]
31 | unsigned int ltq_get_mps_ad0_irq(void)
| ^~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/vmmc.c:40:14: error: no previous prototype for 'ltq_get_mps_ad1_irq' [-Werror=missing-prototypes]
40 | unsigned int ltq_get_mps_ad1_irq(void)
| ^~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/vmmc.c:49:14: error: no previous prototype for 'ltq_get_mps_vc_irq' [-Werror=missing-prototypes]
49 | unsigned int ltq_get_mps_vc_irq(int idx)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/pci/ifxmips_pcie.c:1084:36: error: invalid use of undefined type 'struct platform_device'
1084 | struct device_node *node = pdev->dev.of_node;
| ^~
arch/mips/pci/ifxmips_pcie.c:1204:12: error: no previous prototype for 'ifx_pcie_bios_init' [-Werror=missing-prototypes]
1204 | int __init ifx_pcie_bios_init(void)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/lantiq/xway/ath5k_eep.c:34:12: error: no previous prototype for 'of_ath5k_eeprom_probe' [-Werror=missing-prototypes]
34 | int __init of_ath5k_eeprom_probe(struct platform_device *pdev)
| ^~~~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/eth_mac.c:15:11: error: no previous prototype for 'ltq_get_eth_mac' [-Werror=missing-prototypes]
15 | const u8* ltq_get_eth_mac(void)
| ^~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This patch fixes the following build warnings:
arch/mips/lantiq/xway/timer.c:160:14: error: no previous prototype for 'ltq_get_fpi_bus_clock' [-Werror=missing-prototypes]
160 | unsigned int ltq_get_fpi_bus_clock(int fpi) {
| ^~~~~~~~~~~~~~~~~~~~~
arch/mips/lantiq/xway/timer.c:803:36: error: invalid use of undefined type 'struct platform_device'
803 | ret = devm_mutex_init(&pdev->dev, &timer_dev.gptu_mutex);
| ^~
arch/mips/lantiq/xway/timer.c:864:12: error: no previous prototype for 'lq_gptu_init' [-Werror=missing-prototypes]
864 | int __init lq_gptu_init(void)
| ^~~~~~~~~~~~
arch/mips/lantiq/xway/timer.c:873:13: error: no previous prototype for 'lq_gptu_exit' [-Werror=missing-prototypes]
873 | void __exit lq_gptu_exit(void)
| ^~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add WED related nodes to the device tree of the MT7988 SoC family.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches from kernel 6.13:
- net: dsa: realtek: Use for_each_child_of_node_scoped()
- net: dsa: realtek: rtl8365mb: Make use of irq_get_trigger_type()
- net: dsa: realtek: rtl8366rb: Make use of irq_get_trigger_type()
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19381
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add driver packages for Intel Low-Power Subsystem devices which are part
of some Intel chipsets. They are mainly needed to have access to the I2C
bus used for HID devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current offset used for extracting QCN6122 calibration data
is incorrect on the Yuncore AX830. This patch corrects the
offset to ensure proper WiFi initialization.
Tested on: Yuncore AX830
Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
Link: https://github.com/openwrt/openwrt/pull/19416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Support for 6.12 is ready; add it as a testing kernel.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Most of them were manually refreshed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No need to keep it in kernel specified folder anymore.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Many x86 machines can boot from SD cards, and some embedded x86 devices
come with an eMMC. Include drivers for all common MMC/SDHCI controllers
to allow booting from SD/MMC on x86.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Directly call the function "get_linux_version()" to get the integer
kernel version number.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, if OEM recovery flashes OpenWrt to second ubi1,
OpenWrt cannot boot. With this commit, recovery image is built
with initramfs kernel, so that it can boot from either ubi or ubi1.
This adds an extra step to OpenWrt installation from OEM:
user needs to sysupgrade from initramfs to full system.
Signed-off-by: Mateusz Krzak <kszaquitto+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18878
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8mA driving will cause overshoot issue on SPI NAND. Change it to 4mA.
- Reference:
003744197a
On Linux mainline (mt7986.dtsi), spi's source clock is: clocks = <&topckgen CLK_TOP_MPLL_D2>, which is
208MHz. Usable clock division will be:
- 208/4=52MHz
- 208/6~=35MHz
- 208/8=26MHz
and so on
If we specify 50MHz for spi-max-frequency, it will actually run under about 35MHz. Most SPI NAND & NOR
flashes are capable of running with more than 52MHz, include Micorn MT29F4G01ABAFDWB on ZyXEL EX5601.
[Ref: #18752] To reach highest performance on mt7986, use spi-max-frequency = <520000000>. Basically,
this setting should work on all mt7986 PCBs since most mt7986 boards follow reference design. However,
other boards needs further test to guarantee stability.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18813
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In rtl931x_led_init, the number of leds per port is not properly set. It
currently uses a hardcoded value of 1 which seems to be taken initially
from a specific device. This hardcoded value assumes any port always has
exactly two leds.
The RTL930x variant - rtl930x_led_init - does a better job at this. So
take it and use it for RTL931x too with the corresponding register.
While at it, rename the function to a proper naming scheme.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These cpu erratums are used by other SoCs, just remove them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These cpu erratums are used by other SoCs, just remove them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move the following kernel symbol configs to generic:
COMPRESSED_INSTALL and IMX_SCMI related configs
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band
wireless access point. Very similar to already supported APL26-0AE,
which all antennas are external, while this variant has internal
antennas. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 1x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "ap135.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 ap135.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Notes
By default no power is provided on USB port, so attached USB devices
won't enumerate. To change that enable regulator with:
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
To disable power write "disabled" to the same file.
Ther regulator state will reset on reboot, consider running this command
on hotplug event or add it to /etc/rc.local. The hotplug event should
look like this:
if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
fi
Place it in /etc/hotplug.d/usb/10-usb-power.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unfortunately they still apear with prolonged serial console usage.
While it's not common to use serial console past initial setup, alas
when the condition is hit the console is almost unusable.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250618170045.473711-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The bootup of the armsr target sometimes failed like this:
```
[ 0.762283] NET: Registered PF_INET6 protocol family
[ 0.791987] workqueue: Failed to create a worker thread: -EAGAIN
[ 0.801986] workqueue: Failed to create a rescuer kthread for wq "mld": -EAGAIN
[ 0.964017] NET: Unregistered PF_INET6 protocol family
```
Increase the maximum number of threads the kernel allows.
Link: https://github.com/openwrt/openwrt/pull/19376
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Wavlink Aerial HD3 (WL-WN570HA2) is an AC1200 dual-band outdoor
access point. It supports 802.3AT/AF PoE and is IP67 waterproof.
It is based on the MediaTek MT7628DAN SoC and MT7613BEN WiFi 5 chip.
This model uses the 100Mbit LAN and 2.4Ghz WiFi elements of the
MT7628 and the 5Ghz WiFi of the MT7613.
Specification:
- SoC: MediaTek MT7628DAN (1C/1T) @ 580MHz
- RAM: 64MB DDR2 (integrated in SoC)
- FLASH: 16MB SPI NOR (Fudan FM25Q128A)
- Ethernet: 1x 10/100Mbps
- WiFi: 2.4/5 GHz 2T2R
- 2.4GHz MediaTek MT7628DAN bgn
- 5GHz MediaTek MT7613BEN nac
- Antennas: 2x detachable, dual-band 7dBi with RP-SMA connectors.
- USB: none
- BTN: Reset
- LED: 6 total: power; WAN/LAN; WiFi; WiFi low; WiFi med; Wifi high
- UART: surface-mount on PCB. Pins are marked via silkscreen.
pin1 (square pad, towards Ethernet)=Vcc, pin2=RX,
pin3=TX, pin4=GND. Settings: 57600/8N1.
NOTE: The TX & RX silkscreens were reversed on my test unit.
Installation:
1) This device requires a HTTP recovery procedure to do an initial load
of OpenWRT. You will need:
a. A web browser (private window recommended)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1
c. Connect a cable between the computer and the Wavlink's PoE injector.
2) Put the Wavlink in HTTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
powering the unit on.
b. As soon as all 6 LEDs light up blue (roughly 2-3 seconds), release
the button.
c. The LEDs should all remain lit, indicating it's in HTTP recovery.
3) Point the browser at http://192.168.1.1/index.html
4) Click "Choose File" and select the OpenWRT sysupgrade image.
5) Click the "Update Firmware" button and wait while the unit flashes
the image and reboots.
6) When the system comes back up fully, only the power LED will be lit.
Wait an extra minute then you should be able to reach OpenWRT on
http://192.168.1.1
5) Log into LuCI as root; there is no password.
Revert to the OEM Firmware:
--------------------------
* U-boot HTTP:
Follow the HTTP recovery steps, and use a firmware image downloaded
from Wavlink.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
Link: https://github.com/openwrt/openwrt/pull/18856
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add/enable 2nd USB bus (integrated ath3k bluetooth) to dts. This already
exists in the qca956x dtsi, adding the pointer here to bring the bluetooth to life.
The 2nd bus hosts the integrated bluetooth at 0x1b400000.
See in the comments for more info:
c5b7ec8cee
Tested-by: Russ Innes <russ.innes@gmail.com> on Ubiquiti Amplifi HD .
Signed-off-by: Russ Innes <russ.innes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is similar to the TP-Link EX220 v1.
The differences are the number of ports (3 LANs
and 1 WAN) and the number of LEDs (1 LED RGB)
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LED - (TX - RX - GND - 3V3 ) - ETH ports
Installation
------------
Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:
1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
not to attempt saving settings.
Revert to stock firmware
------------------------
Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.
Web-Recovery
------------
The router supports an HTTP recovery mode:
1. Turn off the router.
2. Press the reset button and power on the device.
3. When the LED start flashing, release reset and quickly press it
again.
The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.
Signed-off-by: Gustavo Curi <gpcuri@land.ufrj.br>
Link: https://github.com/openwrt/openwrt/pull/19104
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since not every device sets an ubifs partition name as the same as their
parent mtd partition, this change allows mount_ubi_part to usable in
other devices
Signed-off-by: Yonghyu Ban <yhban@silicon.moe>
Link: https://github.com/openwrt/openwrt/pull/19203
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 Pro**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
Cherry-picked from 949d0bd77a
Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19315
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The operating mode of a SerDes must be aligned with the attached PHY or
SFP module. That does not only require to change the protocol (e.g. SGMII,
10Gbase-R, ...) but also the speed (e.g. 1.25G). For this the SerDes must
be re-initialized properly.
- It must be taken into power down
- The PLL speed must be set
- Maybe the CMU (clock management unit) must be resetted
- The new mode must be set
- The state machine must be resetted
- The power must be reactivated
Until now this sequence is bugged. First the driver relies on a clean
setup from U-Boot (rtk network on) and second trying to to change mode
and PLL speeds does not work at all. And not to forget: Currently two
adjacent SerDes cannot drive SGMII/HSGMII at the same time. Fix this by
taking care about the right SerDes/PLL/CMU command init order.
P.S. This code is inspired by the work of Jan Hofmann, who tried to
enable parallel SGMII/HSGMII mode. The only missing bit was a proper CMU
reset sequence.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19220
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changing the node names arbitrarily broke existing configurations, which
rely on the device path in /etc/config/wireless.
Revert that part of the change without altering the compatible strings.
Fixes: 7e09959efd ("mac80211: fix wmac node names")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RTL8261N driver does not work correctly on non-mediatek devices. Remove
some of the power controls for Realtek chips.
This assumes the network has been started by the bootloader already:
(rtk network on).
Co-authored-by: Sebastian Gottschall
- bf45143f03
- 2fb02a5745
- 598a16a8d8
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19081
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the RTL8264 (quad-10G phy) by matching the appropriate PHY_ID
in the driver.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19081
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace .remove_new with .remove for compatibility with future kernel versions.
Dropping compatibility with older kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
Drop configs and patches for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to Linux kernel version 6.12.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>
Comes with kernel 6.16. I assume it will be backported at some point.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patch backporting netdev_tx_reset_subqueue new OP has been already
backported in recent minor kernel version for 6.6.
Drop the related patch to fix compilation error on 6.6.
Fixes: 34ba7e8a8a ("generic: backport some flow offload helper patch")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backpot upstream patch for Flow Offload support for AN7581 and refresh
all affected patch. To correctly work a dedicated firmware is needed to
use the dedicated Network Coprocessor (NPU).
This also introduce good cleanup and moves the driver in a dedicated
Airoha directory. While currently not totally usable (due to lack of
firmware blob) this is needed to backport support for external PHY/SFP
support.
Refresh all affected patch.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport some upstream patch for Airoha ethernet driver in preparation
for Flow Offload support.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport some flow offload helper patch in preparation for Airoha Flow
Offload support.
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace PCIe patch with upstream version and update DTS with new PBUS
CSR property now required.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replaced all mt76@ with wifi@ per upstream requirement for all wifi
nodes.
Added missing compatible string where appropriate as stated by mt76.yaml
upstream.
Also updated reg value to be consistent everywhere.
Replace all pci14c3 entries to use mediatek,mt76.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19067
Signed-off-by: Robert Marko <robimarko@gmail.com>
Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.
Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks
Signed-off-by: Dim Fish <dimfish@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17963
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The RTL931x devices have an other register that describes the
current RAM configuration. Enhance the identification routine.
Tested on LGS352C (RTL9311).
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19284
Signed-off-by: Robert Marko <robimarko@gmail.com>
Until now the rt-loader only works on U-Boot driven devices where the
environment (e.g. coprocessor) is usually setup properly. Devices like
the ZyXEL GS1920 series use BootBase as start environment and skip
some of the basic initialization steps. rt-loader will fail in these
cases. Take care about the CP0 registers.
Additionally enhance the documentation of the printf implementation.
It was optimized during the different revisions of the initial PR.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19253
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are too many supported Realtek devices so avoid activating the
rt loader recipe in the default builds. Just start with the LGS310C.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>
To make use of the new rt-loader provide the needed recipes.
This has been tested with the following devices:
- rtl838x Linksys LGS310: initramfs & flash
- rtl930x Zyxel XGS1210: initramfs
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bootloader of many Realtek switches only supports gzipped kernel images.
With limited flash space that might get critical in future versions. For better
compression allow support for compressed images. For this a new loader was
developed. Several ideas have been taken over from the existing lzma loader
but this has been enhanced to make integration simpler. What is new:
- Loader is position independent. No need to define load addresses
- Loader identifies device memory on its own
- Loader uses "official" upstream kernel lzma uncompress
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/lib/decompress_unlzma.c
- Loader uses "official" UNMODIFIED nanoprintg that is used by several
bare metal projects. https://github.com/charlesnicholson/nanoprintf
Compiled the loader ist just under 12KiB and during boot it will show:
rt-loader
Found RTL8380M (chip id 6275C) with 256MB
Relocate 2924240 bytes from 0x80100000 to 0x8fce0000
Extract kernel with 2900144 bytes from 0x8fce521c to 0x80100000...
Extracted kernel size is 9814907 bytes
Booting kernel from 0x80100000 ...
[ 0.000000] Linux version 6.12.33 ...
[ 0.000000] RTL838X model is 83806800
...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move changes to mt7988a.dtsi from patch adding the support for the
MT7988A Reference Board to a dedicated patch to ease maintainance.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Restore the conversion to an all-UBI NAND layout and use of fitblk on
SPI-NAND connected via the mt65xx SPI controller.
Apply the same also for SPI-NAND connected via the SNFI controller, and
use fitblk also for boot from SPI-NOR, eMMC and SD.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek MT7988A RFB currently hangs on boot as CCI fails to probe.
This is due to the wrong SoC compatible string "mediatek,mt7988" instead of
"mediatek,mt7988a". Fix that.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
During setup the mdio driver decides the polling mode of the 4 smi
busses depending on the DTS phy settings. This works as follows:
- set polling to c45 if at least one phy is ethernet-phy-ieee802.3-c45
- set polling to c22 if all phys are ethernet-phy-ieee802.3-c22
On RTL930x it is not possible to switch to c22 if uboot has set c45
before. Fix this by overwriting the bitfield properly. While we are
here:
- Sort variables according to kernel style (inverse christmas tree)
- Initialize fields properly with = { 0 }
- Use GENMASK() for better readability
- Make use of RTMDIO_MAX_SMI_BUS
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19161
Signed-off-by: Robert Marko <robimarko@gmail.com>
This will allow more flexibility in using PHY drivers as kmods.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
After update to v6.12 some PCS driver fixes were dropped and additional
are needed due to updated driver.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
The original PCS driver did not use the .pcs_validate() in
phylink_pcs_ops. The patches for 1000/2500base-x and 10g modes were
taken from this old driver, and thus did not bother with
.pcs_validate(). Thus, even though these modes are supported, phylink
would not enable them.
To fix these, list these modes in .pcs_validate(). Also list them in
ipq_pcs_clk_rate_get(). While the latter does not appear to change
behavior, it does change the clock rates listed under
/sys/kernel/debug/clk
Co-developed-by: Mantas Pucka <mantas@8devices.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
0102-arm64-dts-qcom-ipq9574-Fix-USB-vdd-info.patch was merged in 6.12.34
Other patches automatically refreshed.
Fixes: cb1b656027 ("kernel: bump 6.12 to 6.12.34")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/19232
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using TFTP install method on a fresh unit, wifi_fw and ubi_rootfs UBI volumes must be removed or will hang when mounting.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/19215
Signed-off-by: Robert Marko <robimarko@gmail.com>
As a workaround to an issue causing hang during PCI enumeration on
imx8mp with a specific PCIe switch, disable PCI AER.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19189
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable DT overlay support:
- add dt-overlay to board features
- add DEVICE_DTS_OVERLAYS
- update the boot script to resize before applying each overlay
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19189
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport some additional upstream patches:
- 6.13-arm64-dts-imx8mm-venice-gw73xx-remove-compatible-in-overlay-files.patch
(this resolves some issues when using dt overlays on gw73xx-0x)
- 6.16-PCI-imx6-Skip-link-up-workaround-for-newer-platforms.patch
- pending-PCI-imx6-Remove-apps_reset-toggle-in-_core_reset-function
(these resolve enumeration issues on imx8mm/imx8mp with a pcie switch)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19189
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
SoC: MediaTek MT7628NN
RAM: 128 MB, EtronTech EM68C16CWQG-25H (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n
GPIO: 3 buttons (Wi-Fi, Reset, FN), 3 LEDs (Power, Internet, Wi-Fi), 1 port USB 2.0
Disassembly:
At the bottom, under the LEDs, there are 2 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 5 pin dots located on the right between the operating mode switch and the antenna.
Pins (from antenna to operating mode switch):
VCC
TX
RX
NC
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1212_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1212_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/19157
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Until now the timer management on the RTL931x devices depends
on the MIPS default timer. Looking at the clock progress on
these devices one can see that it is totally off. It is running
at half the required speed (e.g. if 1 minute passes the date
command shows that according to the timers only 30 seconds have
elapsed). This is a mix from wrong DTS and bad startup code.
This is not only a cosmetic issue but has effects on every
delay operation inside the kernel. Switch RTL931x to the proven
Otto timer.
Tested on LGS352C based on RTL9311.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19205
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Otto timer is very helpful on the RTL931x devices.
Include it into the builds.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19205
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream has gained support for forced affinity settings in the MIPS
GIC interrupt controller. This is needed to enable the Otto timer on
the RTL931x platform. See
https://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git/
commit/?id=2250db8628a0d8293ad2e0671138b848a185fba1
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19205
Signed-off-by: Robert Marko <robimarko@gmail.com>
Check Point V-80 (Quantum Spark 1590 Appliance) is an Appliance, based
on Armada 8040 (88F8040).
Specification:
- SoC : Marvell Armada 8040 (88F8040)
- RAM : DDR4 2 GiB (4x 512 MiB chip)
- Flash : eMMC 4 GiB
- Ethernet : 10x 10/100/1000 Mbps
- LAN 1-8 : Marvell 88E6393X
- WAN : Marvell 88E1512
- DMZ : Marvell 88E1512 (RJ-45/SFP combo)
- LEDs/Keys (GPIO): 11x/1x
- UART : "CONSOLE" port (USB 1.1 Type-C)
- chip : Silicon Labs CP2102N
- port : ttyS0
- settings : 115200bps 8n1
- HW Monitoring : 2x nuvoTon NCT7802Y
- USB : USB 3.0 Type-A
- Power : 12 VDC, 3.3 A
- plug : DC Plug 2.5/5.5 mm (inner/outer)
Flash instruction (common):
1. Boot V-81 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
CLI by `expert` command
3. Update U-Boot environment variables by the following commands
fw_setenv bootcmd_ow_usb 'usb start; load usb 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_sd 'load mmc 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_emmc 'run set_mmc_internal; mmc read ${loadaddr} ${prim_header_mmc_blk} 4 && source ${loadaddr}'
fw_setenv bootcmd 'run bootcmd_ow_usb; run bootcmd_ow_sd; run bootcmd_ow_emmc; run bootcmd_part${activePartition};'
Attention: don't forget single quatations of values to prevent
expansion of variables
4. Turn off the device
Flash instruction (USB-boot/SD-boot):
1. Extract and burn (squashfs|ext4)-sdcard.img.gz to USB storage or
MicroSD card
2. Connect that storage to V-81
3. Turn on V-81 and it will be booted with OpenWrt in that USB storage
Flash instruction (eMMC-boot):
1. Copy initramfs image, dtb and bootsctipt to the USB storage with
renaming
initramfs.bin -------> Image
dtb -----------------> armada-8040-v-81.dtb
bootscript (.scr) ---> boot.scr
2. Connect that storage to the USB 3.0 port on V-81
3. Turn on V-81 and it will be booted with OpenWrt initramfs image in
that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-81
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing
Reverting to stock firmware:
1. Turn on V-81 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting
Notes:
- The partition table in the internal eMMC has single partition, but
"blkdevparts=" parameter will be passed from the bootloader and that
definition will be used instead.
- The port-side LED pairs of RJ-45/SFP ports on V-81 are switched by a
GPIO pin of pin7 on &cp0_gpio2. (High(1): RJ-45, Low(0): SFP)
This needs to be switched manually.
- The MicroSD card slot is too unstable and the following messages are
printed without "marvell,xenon-phy-slow-mode;" property.
[ 97.060851] mmc0: error -84 whilst initialising SD card
[ 97.137049] mmc0: error -84 whilst initialising SD card
[ 97.214315] mmc0: error -84 whilst initialising SD card
...
- There are no detailed information about maximum power consumption
limit of the SFP port or optional DSL-SFP modules sold officially.
But the power requirement of almost DSL-SFP modules are 3.3V/700mA, so
set the maximum value of the SFP port to 2000 mW (Power Level III).
- Do not insert a MicroSD card before turning of the device when OpenWrt
installation. The stock firmware deletes all files in the first
partition automatically, to use it as a storage for logs.
MAC addresses:
LAN: 00:1C:7F:xx:xx:FA (mmcblk1boot0, ethaddr (text))
WAN: 00:1C:7F:xx:xx:F9 (mmcblk1boot0, eth2addr (text))
DMZ: 00:1C:7F:xx:xx:FB (mmcblk1boot0, eth1addr (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Check Point V-80 (Quantum Spark 1550 Appliance) is an Appliance, based
on Armada 7040 (88F7040).
Specification:
- SoC : Marvell Armada 7040 (88F7040)
- RAM : DDR4 2 GiB (4x Nanya NT5AD512M8D3-HR)
- Flash : eMMC 4 GiB (Toshiba THGBMNG5D1LBAIL)
- Ethernet : 6x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6352
- WAN : Marvell 88E1512
- LEDs/Keys (GPIO): 6x/1x
- UART : "CONSOLE" port (USB 1.1 Type-C)
- chip : Silicon Labs CP2102N
- port : ttyS0
- settings : 115200bps 8n1
- HW Monitoring : 2x nuvoTon NCT7802Y
- USB : USB 3.0 Type-A
- Power : 12 VDC, 3.3 A
- plug : DC Plug 2.5/5.5 mm (inner/outer)
Flash instruction (common):
1. Boot V-80 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
CLI by `expert` command
3. Update U-Boot environment variables by the following commands
fw_setenv bootcmd_ow_usb 'usb start; load usb 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_emmc 'run set_mmc_internal; mmc read ${loadaddr} ${prim_header_mmc_blk} 4 && source ${loadaddr}'
fw_setenv bootcmd 'run bootcmd_ow_usb; run bootcmd_ow_emmc; run bootcmd_part${activePartition};'
Attention: don't forget single quatations of values to prevent
expansion of each variables
4. Turn off the device
Flash instruction (USB-boot):
1. Burn (squashfs|ext4)-sdcard.img.gz to USB storage
2. Connect that storage to the USB 3.0 port on V-80
3. Turn on V-80 and it will be booted with OpenWrt in that USB storage
Flash instruction (eMMC-boot):
1. Copy initramfs image, dtb and bootsctipt to the USB storage with
renaming
initramfs.bin -------> Image
dtb -----------------> armada-7040-v-80.dtb
bootscript (.scr) ---> boot.scr
2. Connect that storage to the USB 3.0 port on V-80
3. Turn on V-80 and it will be booted with OpenWrt initramfs image in
that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-80
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing
Reverting to stock firmware:
1. Turn on V-80 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting
Notes:
- V-80 has some HW versions. Internal MicroSD card slot and mPCIe slot
is available on some HW versions, but not on the other HW versions.
confirmed (MicroSD/mPCIe slots):
- 1.0.1: unavailable
- 1.0.3: available
- The partition table in the internal eMMC has single partition, but
"blkdevparts=" parameter will be passed from the bootloader and that
definition will be used instead.
MAC addresses:
LAN: 00:1C:7F:xx:xx:4B (mmcblk1boot0, ethaddr (text))
WAN: 00:1C:7F:xx:xx:4A (mmcblk1boot0, eth1addr (text))
Tested-by: Yanase Yuki <dev@zpc.st>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add image-specific signature support to Build/boot-scr.
This is required to switch root devices passed to the kernel on Check
Point V-80 and V-81.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable "emmc" feature to use the emmc helpers on sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable CONFIG_CMDLINE_PARTITION symbol to use "blkdevparts=" parameter
support on Check Point V-80.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Expose the sysfs interface to userspace tools for power monitoring.
Useful for tracking energy usage in CPU package, cores, DRAM, etc.
Build system: x86/64
Build-tested: x86/64
Run-tested: x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18255
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix the status indicator light of the LAN port.
Signed-off-by: jinkela air <air_jinkela@163.com>
Link: https://github.com/openwrt/openwrt/pull/19135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is similar to the Cudy TR3000 v1 128MB version.
The difference is that the flash memory is 128mb and the other is 256mb
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 256 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Power: 5 VDC, 3 A
Installation:
Cudy has distributed intermediate firmware to make installation easier
1. Go to [Cudy CN official website](https://www.cudy.com/zh-cn/pages/download-center/tr3000-1-0) and download the intermediate firmware
2. Upgrade the intermediate firmware on the page
3. Visit the intermediate firmware 192.168.1.1 webpage and use the sysupgrade image to update
other:
If you fail to flash the device, you can use TFTP to flash back to the original firmware.
1. Ask Cudy CN official customer service for the original firmware
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an recovery.bin firmware file.
Signed-off-by: cheng wang <typedelta@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove all files etc. for 6.6 because 6.12 is default now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19139
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use Linux 6.12 as default for all subtargets.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19139
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
REMARK! The original commit c829bc1f2c ("realtek: Add support for
Netgear S350 series switches GS308T and GS310TP") says that the SFP
ports are untested. Looking at device internal pictures from
https://techinfodepot.shoutwiki.com/wiki/Netgear_GS310TP there are no
external phys for the SFP ports. So fix port description.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Until now only the RTL930x devices make use of the following notation.
phy8: ethernet-phy@8 {
compatible = "ethernet-phy-ieee802.3-c22";
phy-is-integrated;
reg = <8>;
sds = <3>;
};
This indicates that the link is driven by a serdes directly without
external phy. As the devices have multiple serdes it must be clarified
what serdes is responsible for that port.
Nevertheless all other devices have the same requirements. E.g. RTL838x
usually drives port 24 from serdes 4 and port 26 from serdes 5. All this
currently works because the driver has a lot of hardcoded port/serdes
mapping.
Make the situation better by adding dts helpers that can describe the
topology as needed.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
This broke the armsr/armv8 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/19200
Signed-off-by: Robert Marko <robimarko@gmail.com>
Run this script:
./scripts/kconfig-reorder.sh
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/19200
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows the SFPs to work without manually switching port type.
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/18914
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 4 sfp ports on the RTL8214FC are actually wired to the gpio expander instead of internal.
Relatively minor changes to the dts are required, simply overriding some of the properties
inherited from rtl8393_hpe_1920.dtsi.
The speed is reported as 100/full and the media type is incorrect, but the ports pass traffic
just fine.
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/18914
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Qualcomm TSENS driver only exposes sensors to as a thermal
zone without registering hwmon, making these temperature sensors
unreadable by lm-sensors. This commit enables CONFIG_THERMAL and
CONFIG_THERMAL_HWMON for qualcommbe target to access the sensors
from hwmon.
Suggested-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/19137
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Qualcomm TSENS driver only exposes sensors to as a thermal
zone without registering hwmon, making these temperature sensors
unreadable by lm-sensors. This commit enables CONFIG_THERMAL and
CONFIG_THERMAL_HWMON for qualcommax targets to access the sensors
from hwmon.
Suggested-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/19137
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now on Linux 6.12, stm32-dfsdm-adc also depends on
kmod-industrialio-backend.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18740
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add kernel module package for Digital Camera Memory Interface Pixel
Processor (DCMIPP) support for kernel 6.12.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18740
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The stm32 target now supports 6.12 kernel as testing.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18740
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18740
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add new and remove obsolete symbols for Kernel 6.12
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/18975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/18975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch of kernel 6.12 missing cpufreq part for
mt7988d, causing the ccifreq driver probe to fail.
Add it to avoid mt7988d devices boot hang.
Fixes: a9822e8 ("kernel/mediatek: 6.12: drop patches which have been applied upstream")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
These kernel config symbols are selected by all sub-targets. We
can merge them together to simplify the config files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All kernel config symbols are refreshed by `make kernel_oldconfig`.
Some symbols are moved to the generic/config-6.12 because the
refresh tool will automatically trim them.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SMP environment is prepared well for the RTL93X. Now describe the
power cluster controller in the DTS. Tested on RTL9311 based Linksys
LGS352C.
Without patch:
root@OpenWrt:~# dmesg | grep CPU
[ 0.140425] CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.191952] Synchronize counters for CPU 1: done.
[ 1.232191] CPU2: failed to start
[ 1.237863] No online CPU in core 1 to start CPU3
[ 2.273784] CPU3: failed to start
[ 2.277589] smp: Brought up 1 node, 2 CPUs
root@OpenWrt:~# cat /proc/cpuinfo | grep -E "model|proc"
processor : 0
cpu model : MIPS interAptiv (multi) V2.0
processor : 1
cpu model : MIPS interAptiv (multi) V2.0
With patch:
root@OpenWrt:~# dmesg | grep CPU
[ 0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Failed to get CPU clock: -2
[ 0.000000] CPU frequency from device tree: 1000MHz
[ 0.133360] smp: Bringing up secondary CPUs ...
[ 0.140418] CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.191950] Synchronize counters for CPU 1: done.
[ 0.230103] CPU2 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.289220] Synchronize counters for CPU 2: done.
[ 0.326189] CPU3 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.378861] Synchronize counters for CPU 3: done.
[ 0.413829] smp: Brought up 1 node, 4 CPUs
processor : 0
cpu model : MIPS interAptiv (multi) V2.0
processor : 1
cpu model : MIPS interAptiv (multi) V2.0
processor : 2
cpu model : MIPS interAptiv (multi) V2.0
processor : 3
cpu model : MIPS interAptiv (multi) V2.0
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduced with Linux 6.7, in commit:
5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the mtdsplit_uimage driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
E.g. on Realtek devices that are booted for the first time through
initramfs with OpenWrt never installed before boot log will show
[ 0.975518] Creating 7 MTD partitions on "spi0.0":
[ 0.981062] 0x000000000000-0x0000000e0000 : "u-boot"
[ 1.041320] 0x0000000e0000-0x0000000f0000 : "u-boot-env"
[ 1.060683] 0x0000000f0000-0x000000100000 : "u-boot-env2"
[ 1.080992] 0x000000100000-0x000000200000 : "jffs2-cfg"
[ 1.100988] 0x000000200000-0x000000300000 : "jffs2-log"
[ 1.120599] 0x000000300000-0x000000fe0000 : "firmware"
[ 1.157426] mtdsplit_uimage: no rootfs after uImage in "firmware"
[ 1.176456] mtdsplit_uimage: no rootfs after uImage in "firmware"
[ 1.200262] 0x000000fe0000-0x000001000000 : "log"
Similar issues were fixed before with commit ade045084b
("kernel: mtdsplit_minor: return 0 if not fatal") and
c78765213e ("kernel: mtdsplit_uimage: return 0 if not fatal")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19163
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Due to a bug, USB is not powered on after boot on hAP ac.
This prevents extroot configurations from working as overlayfs is mounted
before USB device can be powered on. This commit fixes this by enabling USB
in devicetree.
Related discussion links:
- https://forum.openwrt.org/t/usb-power-is-off-on-boot/229007
---
Extroot configuration requires the USB to be powered on before
preinit_main/80_mount_root. Probably the simplest approach is to enable
it in the devicetree. Another approach would be to add a script into
/lib/preinit that will power on USB via /sys/class/gpio/usb-power/value
E.g.
cat /lib/preinit/79_power_on_usb
do_power_on_usb(){
echo '1' > /sys/class/gpio/usb-power/value
}
boot_hook_add preinit_main do_power_on_usb
Signed-off-by: Valeriy Manzhos <manzhos.va@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
JDCloud RE-SP-01B is a dual-band WiFi 5 router based on the MT7621AT.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 512MB DDR3
- Flash: 32MB SPI NOR
- WiFi: MediaTek MT7603EN (2.4GHz), MediaTek MT7615N (5GHz)
- Ethernet: 1x WAN, 2x LAN (Gigabit Ethernet)
- LEDs: red, blue, green (GPIO controlled)
- Button: Reset (GPIO controlled)
- eMMC: Single onboard (32GB/64GB/128GB)
- USB: 1x USB 2.0 port
MAC Address Structure:
The MAC addresses share the structure DC:D8:7C:XX:XX:XX, where:
- WAN, LAN, and 2.4GHz WiFi: same as the label MAC address.
- 5GHz WiFi: label MAC address + 0x800000.
The manufacturer writes the label MAC address at different
offsets depending on the storage version of the device:
e.g.
128GB version: &config + 0x442a
64GB version: &config + 0x4429
So `get_mac_ascii()` is used here to search for the
base label MAC address of the device.
Ref:
https://github.com/openwrt/openwrt/pull/17409#discussion_r1899674262https://github.com/immortalwrt/immortalwrt/commit/c0c480d
Flash Instruction:
A 3rd party bootloader is required to boot the image. You can
use a SOP16 test clip to burn the image/bootloader to the flash.
The official bootloader does provide a web recovery interface
which only accepts an official image. To access it, you will
need to hold the reset button and power on the device, set your
IP address to 192.168.68.2 and visit http://192.168.68.1.
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Yijie Jin <jinyijie@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The switchcore node is the central location that describes the Realtek switch
register addresses starting at 0x1b000000. It will be used by current and
future regmap enabled device drivers. The upstream MDIO driver already makes
use of it by calling syscon_node_to_regmap(dev->parent->of_node);
In the current DTS base we have 3 issues that should be fixed:
- rtl838x.dtsi has a length of 0x20000 instead of 0x10000
- rtl839x.dtsi has a length of 0x20000 instead of 0x10000
- rtl931x.dtsi has no switchcore node at all
Align these mismatches with the "good" RTL930x template.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18642
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The drivers for I2C bus and mux for RTL931x have an incorrectly defined
SDA0 pin number, causing an error with correct pin numbers specified in
the device tree.
Using the `show tech-support board` on the vendor firmware of a Netgear
MS510TXM shows the correct pin numbers but they don't work with the
drivers. So fix this.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19171
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport accepted BCM5325 patches from net-next.
These patches will be merged in the v6.17 kernel window.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
From now on both SFP ports can be used without manual intervention.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18737
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently only RTL83xx devices are known with shared SCL pins.
So activate the driver only for those targets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18737
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some Realtek switches have been designed with I2C busses that share a
single SCL line. The clock line is used for 2 or more busses. This cannot
be used with the standard i2c-gpio driver that relies on distinct SDA
and SCL pairs.
Provide a derived i2c-gpio-shared driver that can be used instead. This
driver can handle up to 4 busses with only a single clock line.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18737
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
1. Power down the router and hold in the Reset button.
2. While holding in the button power up the router again.
3. Hold the button in for 10 seconds and then release.
4. Use your browser to go to 192.168.1.1
5. If you see a GUI that is for flashing firmware then you have the V2 model.
If there is no GUI and the router continues to boot up normally
you have the V1 model.
6. Now use the V2 sysugrade file.
Note: Recovery GUI it can be used to recover from an incorrect firmware flash.
Based on patches adding support for this device by Yannick Chabanois (openmptcprouter)
and Dairyman (ofmodemsandmen)
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18514
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
root@OpenWrt:~# echo 25000000 > /sys/kernel/debug/mmc0/clock
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This new feature has some improvements for random RW performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MT7628 programing guide shows that the correct DTOC unit is
1048576 clocks instead of 65536 clocks. This value is also used
by linux upstream mtk-sd driver. Correct the DTOC register and
also round up its value.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628NN
RAM: 128 MB, EtronTech EM68C16CWQG-25H (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n
GPIO: 2 buttons (Wi-Fi, Reset), 3 LEDs (Power, Internet, Wi-Fi), 1 mode switch
Disassembly:
At the bottom, under the LEDs, there are 2 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 5 pin dots located on the right between the operating mode switch and the antenna.
Pins (from antenna to operating mode switch):
VCC
TX
RX
NC
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1112_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1112_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/19091
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Zyxel XGS1210-12 Switch is a 10 + 2 port multi-GBit switch with
8 x 1000BaseT, 2 x 10/100/1000/2500BaseT Ethernet ports and
2 SFP+ module slot.
Hardware:
- RTL9302B SoC
- Macronix MX25L12833F (16MB flash)
- Nanja NT5CC64M16GP-1 (128MB DDR3 SDRAM)
- RTL8231 GPIO extender to control the port LEDs
- RTL8218D 8x Gigabit PHY
- RTL8226 2x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 2x 10GBit slot
Power is supplied via a 12V 1.5A standard barrel connector. At the
right side behind the grid is UART serial connector. A Serial
header can be connected to from the outside of the switch trough
the airvents with a standard 2.54mm header.
Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial
connection is via 115200 baud, 8N1.
A reset button is accessble through a hole in the front panel
At the time of this commit, all ethernet ports work under OpenWrt,
including the various NBaseT modes, SFP+ slots are supported with i2c bus.
Installation
--------------
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* Navigate to 'Management' in the OEM web interface and click on 'Firmware upgrade'
to the left.
* Upload the OpenWrt initramfs image, and wait till the switch reboots.
* Connect to the device through serial and change the U-boot boot command.
> fw_setenv bootcmd 'rtk network on; boota'
* Reboot, scp the sysupgrade image to /tmp, verify the checksum and flash it:
> sysupgrade openwrt-realtek-rtl930x-Zyxel_xgs1210-12-squashfs-sysupgrade.bin
* Upon reboot, you have a functional OpenWrt installation. Leave the bootcmd
value as is - without 'rtk network on' the switch will fail to initialise
the network.
Debug
------------
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is requiered, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
> rtk network on
* Change ip address (default is 192.168.1.1):
> setenv ipaddr 192.168.1.6
* Download initramfs:
> tftpboot 0x84f00000 192.168.1.111:openwrt-realtek-rtl930x-Zyxel_xgs1210-12-initramfs-kernel.bin
* Boot loaded file:
> bootm 0x84f00000
This prodecudre also apply to the sock firmware with the file XGS1210-12_V2.00(ABTY.1)C0.bix.
More information can be found on the page of XGS1250-12 as they share the same base.
Signed-off-by: Nicolas BERTRAND <nicolasbertrand89@gmail.com>
[fixed white space error]
Signed-off-by: Paul Spooren <mail@aparcar.org>
The TP-Link TL-ST1008F is an 8-port multi-gig switch with 8x SFP+ ports
which support 1G/2.5G/10G speeds. Out of the box it is an unmanaged
switch but with RTL9303 and sufficient RAM + Flash it easily can run as
a managed Linux switch.
Hardware:
- Realtek RTL9303 Switch SoC
- Winbond 25Q256JVFQ (32MB flash)
- Samsung K4B4G1646E-BYMA (512MB DDR3 SDRAM)
- TCA9534 GPIO extender to control the port LEDs
- 8x SFP+ 1/2.5/10G slot
- Serial: 3V3 logic, 115200 8N1
- 5-pin JTAG
- physical tri-state switch (used by stock firmware for port speed
config)
- 24-LED port speed matrix
- robust full-metal case
Power is supplied via a 12V 2A standard barrel connector.
There are THT holes on the PCB for serial console next to the flash chip
and JTAG pads. Serial uses 3V3 logic and standard 115200-8N1 config.
Pinout is labeled on the PCB.
All ports/connectors and LEDs are on the back, only Power LED is on the
front.
Hints before flashing
----------------------
* It is recommended to backup the stock flash contents before proceeding.
Backup can be done from U-Boot (with memory display), from OpenWrt
initramfs or probably with SPI flash programmer.
There is no stock recovery functionality.
* Use a small image for RAM boot or first flash. Since you need to use
ymodem, this is really slow and takes time.
* This does not keep the dual-partition layout for firmware to have more
space available for a single OpenWrt installation.
Initial flashing
----------------------
The stock U-boot has broken networking thus no TFTP available. Serial
transfer only.
1. Open device and connect serial as per layout and settings
(recommended to use picocom, ymodem not working with minicom)
2. Connect power to device and press Esc when prompted to enter
the U-Boot console.
3. Boot initramfs
* in the U-Boot console:
loady 0x82000000 (load OpenWrt image via ymodem)
CTRL-A CTRL-S <initramfs.bin> (specify initramfs image for
picocom to upload)
bootm 0x82000000 (boot initramfs from RAM)
(Just to be on the safe side, backup your flash now while RAM-booted)
4. Connect network to your device
5. Upload the sysupgrade image (e.g. with scp)
6. Do sysupgrade
There's no need to adjust the bootcmd in U-Boot. Networking is running
fine once the realtek driver initialized everything in OpenWrt. No
functional difference with running 'rtk network on' within U-Boot
before. Running this even fails and returns with an error.
Return to stock
------------------
This only works if you did a backup of the flash before flashing
OpenWrt. Stock dump then can be flashed from within U-Boot or OpenWrt.
There is no vendor firmware image because this is an unmanaged switch!
CAUTION: Make sure to not overwrite the U-Boot partition(s). If you do
not have a flash programmer, you may not be able to debrick
your device then.
Co-authored-by: Balázs Triszka <balika011@gmail.com>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
AIC8800 is a WiFi/BT module based on Ceva's IP.
This driver is old and not enabled in the starfive target,
so remove it. We can add out of tree drivers if necessary.
Fixes: 8f0f02d2 ("starfive: 6.12: refresh patches and drop upstreamed ones")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add support for Xiaomi AX6000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
QCA9887 (1x1 5 Ghz 802.11ac/n - up to 433 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- external QCA8337 switch (3 LAN Ports 10/100/1000)
- QCA8081 Phy WAN port (10/100/1000/2500)
* Flash: Either of:
- Gigadevice GD5F1GQ4RE9IGD (128 MiB)
- ESMT F50D1G41LB (128 MiB)
* LEDs: 1x WLAN Link (GPIO 23 Active High)
1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
1x Green - Unused(GPIO 28 Active High)
3x LAN Phy Green
1x WAN Phy Green
* Buttons: 1x Reset (GPIO 38 Active Low)
Known issue:
- QCA9887 doesn't come up (possibly due to 1-lane PCIe phy not coming up or missing method to drive power),
hence the host PCIe controller is disabled in the DTS.
Flash instructions:
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upon detecting the ID for the ESMT F50D1G41LB chip, the fifth byte
returned is always 0x00 instead of the expected JEDEC continuation code
of 0x7f. This causes detection to fail:
[ 0.304399] spi-nand spi0.0: unknown raw ID c8117f7f00
[ 0.508943] spi-nand: probe of spi0.0 failed with error -524
So let's revert back to the 4 byte ID code for this chip
specifically.
Fixes: 4bd14b2fd8a8 ("mtd: spinand: esmt: Extend IDs to 5 bytes")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qca8k dsa switch can use either an external or internal mdio bus.
This depends on whether the mdio node is defined under the switch node
itself and, as such, the internal_mdio_mask is populated with its
internal phys. Upon registering the internal mdio bus, the
internal_mdio_bus of the dsa switch is assigned to this bus.
When an external mdio bus is used, it is left unassigned, though its id
is used to create the device names of the leds.
This leads to the leds being named '(efault):00:green:lan' and so on as
the internal_mdio_bus is null. So let's fix this by adding a null check
and use the devicename of the external bus instead when an external bus
is configured.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Continuous read does not work properly in on-die ECC mode.
Disable it to fix ubi io error on the GL.iNet GL-MT3000.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix wrong pwm-fan node for bpi-r4.
Remove useless status for pwm-fan.
Remove blank lines added by b992aa11.
Fixes: b992aa11 ("mediatek: dts: bring mt7988a.dtsi closer to upstream")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Only 2 devices use leading zeroes to pad interface names,
align the remaining ones so that it is consistent.
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/18913
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Broadcom BCM4318
- 2x USB 2.0 port
- 2x Button
- 9x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg553-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
I-O DATA WN-DAX3000GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 512 MiB
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 7x/5x
- UART : through-hole on PCB (J3)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- USB : USB 2.0 Type-A (through-hole on PCB, "J6")
- Power : 12 VDC, 1A (Typ. 930 mA)
Flash instruction using factory.bin image:
1. Boot WN-DAX3000GR with router mode
2. Access to the WebUI ("http://192.168.0.1/") on the device and open
the firmware update page ("ファームウェア")
3. Select the OpenWrt factory.bin image and click update ("更新") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW, bootconfig(rootfs)=1):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs_1"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007700000 : "idmkey"
0x000007700000-0x000007c00000 : "Reserved"
0x000007c00000-0x000007c80000 : "FWHEADER"
0x000007c80000-0x000007d00000 : "Factory"
Known Issues:
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
[ 1.542261] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.547959] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.551265] Creating 1 MTD partitions on "0:appsblenv":
[ 1.558096] 0x000000000000-0x000000040000 : "env-data"
[ 1.627282] u-boot-env-layout 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout: probe with driver u-boot-env-layout failed with error -74
root@OpenWrt:~# strings /dev/mtdblock10
[ 77.806720] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[ 77.807554] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 77.815977] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 77.824721] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 77.834095] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 77.843278] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 77.851577] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
- There are through-holes on PCB for USB 2.0, but it cannot be accessed
without disassembly of the housing. So it's not enabled in this
support.
- WN-DAX3000GR has the "bt_fw" volume in the firmware UBI in addition to
the volumes that will be removed in the section of ELECOM WRC-X3000GS2
in /lib/upgrade/platform.sh.
That volume is unnecessary for OpenWrt and add
`remove_oem_ubi_volume bt_fw` to remove that volume when sysupgrade.
(that function doesn't anything without errors if no specified volume)
MAC Addresses:
LAN : 50:41:B9:xx:xx:64 (0:APPSBLENV, "ethaddr"/"eth1addr" (text))
WAN : 50:41:B9:xx:xx:66 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 50:41:B9:xx:xx:64 (0:APPSBLENV, "wifi0" (text))
5 GHz : 50:41:B9:xx:xx:65 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
I-O DATA WN-DAX3000GR has a MSTC (Mitra Star Technology Corp.) specific
header with a different length than ELECOM WRC-X3000GS2.
Make the header length configurable by parameterizing on
Build/mstc-header.
- WRC-X3000GS2: 0x400
- WN-DAX3000GR: 0x480
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
The reason fwmode 2 was used for ipq5018 and qcn6122 wifi was that
coldboot calibration doesn't work and causes the firmware to crach
during wifi bringup. Since coldboot calibration is now disabled in the
driver, all boards can now use their respective firmware memory mode, so
let's the property in all board DTS files accordingly.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19083
Signed-off-by: Robert Marko <robimarko@gmail.com>
The I2C and SPI packages required for each RPi generation is different.
Therefore, in order to avoid confusion let's select them by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Three different code paths for the same phy model. Now the bus
is prepared to handle c45 (mmd) read/writes correctly. Remove
the custom implementations and let generic kernel functions do
their best. To achieve this
- disable the PHY-mode EEE in rtl821x_config_init() as upstream does
- provide mmd read/write functions that avoid EEE via c45 over c22
While chaning the phy_driver functions sort them alphabetically.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
rtl8214fc_media_is_fibre() will need to be run when bus lock is held.
Split the function into two versions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
As the mdio bus has been hardened and can now handle c45 requests
the DSA driver must honor that as well. For this
- add proper upstreamed bus read_c45 and write_c45 functions
- take over the disabled port mask from upstream bus
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the follow up EEE patches the mdio bus will run c22 and c45
accesses during initial scan. Especially when accessing addresses
beyond the CPU port phy requests might fail in a way that cannot
be handled gratefully. Do two things
- do not allow access to addresses starting from cpu port
- set the scan disable bitmask to ports starting from cpu port
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some bits where missed during the last enhancement of the mdio
patch. In the forthcoming patches the phy_mask will be populated
to avoid unwanted ports (>= cpu port) from being scanned. Add
additional locations where 32 bit values need to be converted
to 64 bits.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
If mmd and normal phy ops are issued the bus is lost because
of wrong park page settings. Force it to 0x1f as in GPL.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow to build the new kernel.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The new kernel has relocated the definition of struct platform_device.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The DSA driver uses set_mac_eee() for the outside API while
the interal helper is called port_eee_set(). Align that.
Additionally do not call the internal helpers directly by
the function names but use the register assignments.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream will get rid of the get_mac_eee() function in the DSA
driver and replace it by a boolean alternative. While we fill a
lot of data here (because of EEE bugs in the Realtek phy layer)
other DSA drivers only return if EEE is available or not for a
port. To make the next kernel upgrade easier follow that design.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
To avoid unneeded interrupts the R4K timer is deactivated during
secondary cpu initialization. This is currently done during
phase init_secondary(). With the upgrade to 6.12 the kernel runs
a primary/secondary cpu timer/counter synchronization to verify the
proper setup in synchronise_count_slave(). That runs at a later
point in time and expects the secondary counter to be fully
functional. Finding a deactivated counter results in the following
messages:
WARNING: CPU: 1 PID: 0 at arch/mips/kernel/sync-r4k.c:99 check_counter_warp+0x220/0x254
Warning: zero counter calibration delta: 0 [max: 6500000]
Counter synchronization [CPU#0 -> CPU#1]:
Measured 278760029 cycles counter warp between CPUs
Relocate the deactivation to smp_finsh() at the end of the cpu
startup sequence. Additionally polish the startup code and remove
all unneeded parts.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Per IEEE 802.3 definition we have:
- parallel XGMII for single 10GBit ONLY links
- serial USGMII for 8 port 1GBit links (not known by kernel)
- serial USXGMII: for single/multiple links with a total bandwidth of 10GBit
The phy-mode of the first eight ports of the XGS1250-12 have always been
defined as XGMII (without S). This came from a confusion with the similar
named Realtek proprietary XSGMII (with S) mode that is basically 10GB SGMII.
From the above definition this is wrong but worked until kernel 6.6. With
the upgrade to 6.12 there is an enforced capabilities check within
phy_caps_from_interface() and link validation fails with
lan1: validation of xgmii with support 62ef and advertisement 62c0 failed: -EINVAL
lan1: failed to connect to PHY: -EINVAL
lan1: error -22 setting up PHY for tree 0, switch 0, port 0
Switch the ports to USXGMII as the most flexible option. This might be no
final solution but at least it better describes the phy/mac link.
Fixes 5b8b382df9 ("realtek: Add support for ZxXEL XGS1250-12 Switch")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix minor compilation errors due to kernel changes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream has integrated the Realtek target into the generic MIPS
initialization and so MACH_REALTEK_RTL has gained some new features.
Especially:
- CONFIG_MACH_GENERIC_CORE generates central modules
- board-realtek module adds device specific extensions
The current downstream initialization works well and upgrading to
kernel 6.12 is not the right time to harmonize this. Modify the
MACH definitions to the current needs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The validate function no longer exists in phylink_mac_ops. Remove
it for the internal ethernet interface. Instead provide some
meaningful mac capabilities.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Not only the link but also the mac capabilities are needed here.
Additionally do some alphabetical sorting.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The old upstream notation has been changed to something not so racist.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
EEE functions are now called with ethtool_keee instead of
ethtool_eee. Replace all occurrences. This will fix function
signature checks but still produces compilation errors due
to structure changes.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patches where fuzz had to be cleaned up.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
All these patches needed no manual intervention and applied cleanly
with new source code positions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Thanks to Chris Packham this driver got upstreamed. Drop the
downstream files and patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add kernel package for Broadcom Settop/DSL I2C controller.
This controller is used on RPi devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This commit changes LAN1 to be WAN and LAN2 to be LAN, like all other
dual port Extreme Networks devices.
This partially reverts commit 84a489b7cf
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
Fixes LAN LED "1" to show activity of LAN1 and LAN LED "2" to show
activity of LAN2, not vice versa.
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
Update the pin-configuration as well as maximum frequency for the eMMC
flash.
- Use 26 MHz as the maximum clock of the eMMC memory
- Configure 12mA as the pin drive-strength
- Enable internal pull-reistors
Signed-off-by: Yin Ni <yin.ni@gl-inet.com>
[adapt commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The function name is misspelled and does not exist. Fix the function
name so the correct function is called.
Signed-off-by: David Bauer <mail@david-bauer.net>
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
[1] https://github.com/openwrt/openwrt/issues/17351
[2] https://lore.kernel.org/all/0adde34f936a2dafca40b06b408d82afe0852327.camel@mediatek.com/
Tested-by: Darren Tucker
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Closes: https://github.com/openwrt/openwrt/issues/17351
Link: https://github.com/openwrt/openwrt/pull/18585
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Macronix MX29GL128EHT2I-90G
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Ralink RT3062F
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-c-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It's time to give the patches documentation some love by:
- Using Markdown.
- Differentiating between generic and specific target patches.
- Adding deeper explanation about patch numbering.
Link: https://github.com/openwrt/openwrt/pull/19092
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Missing headers causes an error on kernel 6.12:
arch/mips/ralink/irq.c:86:5: error: no previous prototype for 'get_c0_perfcount_int' [-Werror=missing-prototypes]
86 | int get_c0_perfcount_int(void)
| ^~~~~~~~~~~~~~~~~~~~
arch/mips/ralink/irq.c:92:14: error: no previous prototype for 'get_c0_compare_int' [-Werror=missing-prototypes]
92 | unsigned int get_c0_compare_int(void)
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace macros with empty body with 'do {} while (0)'.
Remove unnecessary semicolons.
Fixes:
drivers/mmc/host/mtk-mmc/sd.c: In function 'msdc_irq':
drivers/mmc/host/mtk-mmc/sd.c:1969:87: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1969 | IRQ_MSG("XXX CMD<%d> MSDC_INT_RSPCRCERR", cmd->opcode);
| ^
drivers/mmc/host/mtk-mmc/sd.c:1975:84: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1975 | IRQ_MSG("XXX CMD<%d> MSDC_INT_CMDTMO", cmd->opcode);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reorganize backported 6.12 generic patches, grouping them by following
a standard naming XXX-XX-v6.x-patch-file-name.patch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add uboot-envtools (removing -uboot-envtools) to devices which were
missed in the commit 79bd017 ("ramips: mt7621: add uboot-envtools to
all devices")
- Mi Router 3G
- Mi Router AC2100
While at here remove two redundant entries from devices which were added
just after the referenced commit 79bd017 and did not account for the
new DEFAULT_PACKAGES member:
- SNR-CPE-ME1
- SNR-CPE-ME2-SFP
Fixes: 79bd017 ("ramips: mt7621: add uboot-envtools to all devices")
Fixes: https://github.com/openwrt/openwrt/issues/18960
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the following to fix builds with GCC 15.1:
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/arch/mips/vdso?h=next-20250606&id=0f4ae7c6ecb89bfda026d210dcf8216fb67d2333
% dmesg | grep gcc
[ 0.000000] Linux version 6.6.93 (facade@redline) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 15.1.0 r29972+15-7d617804cfe7) 15.1.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Jun 7 12:13:18 2025
Error for reference:
./include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
| ^~~~~
./include/linux/stddef.h:11:9: note: 'false' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:33: error: 'bool' cannot be defined via 'typedef'
35 | typedef _Bool bool;
| ^~~~
./include/linux/types.h:35:33: note: 'bool' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:1: error: useless type name in empty declaration [-Werror]
35 | typedef _Bool bool;
| ^~~~~~~
CC arch/mips/lib/delay.o
AR arch/mips/fw/lib/built-in.a
AR arch/mips/fw/lib/lib.a
CC arch/mips/ralink/of.o
CC fs/read_write.o
CC block/elevator.o
cc1: all warnings being treated as errors
make[9]: *** [scripts/Makefile.build:243: arch/mips/vdso/vgettimeofday.o] Error 1
make[8]: *** [scripts/Makefile.build:480: arch/mips/vdso] Error 2
Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch contains various minor FDT improvements for ramips
HiWiFi series devices:
* Add mt76 driver compatibles.
* Remove useless platform compatibles.
* Add default USB LED trigger for HC5861.
* Disable unused usbphy for HC5661, HC5661A and HC581B.
* Add switch port map properties based on 02_network scripts.
* Move aliases node to device dts because the LED nodes it
references only exist in the device specific dts.
* Rename gpio-leds nodes to follow the upstream dt-bindings
suggested pattern "(^led-[0-9a-f]$|led)".
* Convert deprecated LED label property to color and function.
"system" LED has been renamed to "status", it is acceptable
because these LEDs do not have text labels.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For all HiWiFi series devices, the base MAC address is stored on
"bdinfo" partition, offset 0x18a, ASCII text format. The recently
introduced "mac-base" nvmem layout can handle the ASCII text now,
so it's time to move MAC address configurations to dts. There is
no valid MAC info in the "factory" partition, hence they will be
replaced with the correct ones.
Tested on HiWiFi HC5661A and HC5861.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Spansion S29GL128P10
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Atheros AR9223
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-a-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Commit Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
removed bridge devices and therefore switch.1 no longer exists, so let's
use br-lan instead.
Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Arcadyan WE410443 is a WiFi AC access point distributed by various ISPs
under various names, including KPN SuperWifi and BT Whole Home Wi-Fi. It
features one ethernet port, dual MT7615N radios and four internal antennas.
Hardware:
- SoC: Mediatek MT7621AT
- Flash: 32 MB
- RAM: 128 MB
- Ethernet: 1x 10/100/1000 Mbps, built into the SoC
- WLAN: 2x MediaTek MT7615N
- Buttons: 1 Reset button, 1 WPS button
- LEDs: 1x Green, 1x Blue, 1x Red, all unmarked
- Power: 12 VDC, 1.5A barrel plug
Installation:
The bootloader is locked with a password, so the image needs to be written
directly to the SPI flash chip. To do this, you need to open up the case,
remove the heatsink and connect the flash chip to a Raspberry Pi. Use the
following connections:
Flash chip --> Raspberry Pi
VCC --> 3v3
RESET --> 3v3
/CS --> GPIO 8
DO --> GPIO 9
CLK --> GPIO 11
DI --> GPIO 10
GND --> Ground
You can solder wires to the flash chip, or use a SOIC16 clip. More details on
the Raspberry Pi and SPI chip pinouts are available on the wiki [1]
When you have the Raspberry Pi connected to the flash chip, boot your Pi and
follow the instructions:
1) Make sure your Pi has SPI enabled with sudo raspi-config
2) Install necessary tools: sudo apt install xxd libubootenv-tool mtd-utils
3) Upload overlay and execute:
sudo dtc -@ -I dts -O dtb -o
/boot/overlays/we410443.dtbo we410443-overlay.dts
4) Enable in /boot/firmware/config.txt by adding a new line containing
dtoverlay=we410443
5) Reboot your Pi and verify the mtd partitions with
cat /proc/mtd, you should see:
dev: size erasesize name
mtd0: 02000000 00001000 "all"
mtd1: 00030000 00001000 "u-boot"
mtd2: 00010000 00001000 "u-boot-env"
mtd3: 00010000 00001000 "factory"
mtd4: 01f60000 00001000 "firmware"
mtd5: 00010000 00001000 "glbcfg"
mtd6: 00010000 00001000 "config"
mtd7: 00010000 00001000 "glbcfg2"
mtd8: 00010000 00001000 "config2"
6) Optionally (but recommended), make a backup:
sudo dd if=/dev/mtd0 of=backup.bin
It can be restored with: sudo flashcp backup.bin /dev/mtd0
7) Set the variables for the bootloader:
echo '/dev/mtd2 0x0 0x1000 0x1000' > fw_env.config
sudo fw_setenv -c fw_env.config bootpartition 0
8) Finally, flash the image:
sudo flashcp openwrt-ramips-mt7621-arcadyan_we410443-
squashfs-sysupgrade.bin /dev/mtd4
MAC addresses
The label address is stored in ASCII in the config partition
Use --> Address
Device --> label
Ethernet --> label
WLAN 2g --> + 1
WLAN 5g --> + 2
References:
[1] https://openwrt.org/toh/arcadyan/astoria/we410443
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: https://github.com/openwrt/openwrt/pull/17981
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To simplify the device specific dts, reuse the mt7621 default
XHCI voltage regulators by adding the corresponding GPIO pin
and polarity properties.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have added the default voltage regulators for the mt7621 SoC
dtsi. These redundant voltage regulators can be removed now.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The USB power regulators are essential for the Mediatek XHCI
controller. If any of them is missing, the kernel will throw
a warning. Add fixed voltage io/vbus regulators to workaround
this issue. Fix the following warnings:
[ 7.514572] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 7.522375] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The WR3000E has the same board layout as the WR3000S. Differences:
- Different flash chip
- LEDs with red/blue colour intead of white
Hardware:
- MediaTek MT7981 WiSoC
- 256MB DDR3 RAM
- 128MB SPI-NAND (F50L1G41LB)
- MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
MAC Addresses in OEM firmware:
- There is one on the label, e.g. AA:BB:CC:DD:EE:FF
- WLAN (2.4G) uses the same as on the label
- WLAN (5G) is the one on the label but
- first byte (e.g. AA) + 2
- fourth byte (e.g. DD) - 0x40
- WAN is the one on the label + 1
- LAN is the one on the label
MAC Addresses in OpenWrt:
- Same handling as in WR3000s is used
GPIO:
- 2 Buttons (all low active):
- WPS on GPIO 0
- Reset on GPIO 1
- 6 LEDs (all low active):
- Power: Blue on GPIO 8, no red LED
- WPS: Blue on GPIO 10, Red on GPIO 4
- Internet: Blue on GPIO 11, no red LED
- LAN: Blue on GPIO 9, Red on GPIO 5
- WiFi 2.4G: Blue on GPIO 6, no red LED
- WiFi 5G: Blue on GPIO 7, no red LED
Disassembly:
- Remove the 4 screws at the bottom of the case
- Cover is clipped to the bottom part of the case with clips in the front and the back
UART:
- UART pins are accessible on the bottom of the board
- The connector with the square shape is TX
- Pins: [ ] TX, ( ) RX, ( ) GND, ( ) VCC
- Settings: 115200 8N1 3.3V
Migration to OpenWrt via OEM firmware:
- There should be a migration image available from Cudy as soon as there is official OpenWrt support
- Download the migration image via OEM web interface
- After flashing, OpenWrt is accessible via 192.168.1.1
- Flash the official OpenWrt image
Migration to OpenWrt using TFTP:
- Connect UART as described above
- Press the reset button while powering on the device
- U-Boot will now try to load a recovery.bin via TFTP, this must be ignored
- After detecting a timeout, the U-Boot console is available via UART
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the initramfs image via TFTP as cudy3000e.bin
- Run the following command in U-Boot: tftpboot 0x46000000 cudy3000e.bin; bootm 0x46000000
- OpenWrt initramfs image is now booting and accessible via 192.168.1.1
- Flash the sysupgrade image
Revert back to OEM:
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the Cudy firmware via TFTP as recovery.bin
- Press the reset button while powering on the device
- Recovery process will start now
- After recovery is done, the OEM firmware is available at 192.168.10.1 again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18609
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With the recent fixes backported to 6.12, b53 ports should now fully
work as standalone ports outside of a switch.
So move them out of the switch and use them as standalone ports, which
makes configuring easier as VLANs don't need to be defined and reserved
anymore to use the wan port.
Tested on DGND3700v1.
While most devices do not define a wan port, I dropped the
ucidef_set_bridge_device() from all devices for consistency.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Allow selecting 6.12 as testing kernel on imx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
patches:
- remove patches from 6.7-6.12 that are now upstream.
- refresh remaining patches
- 502-6.13-arm64-dts-freescale-rename-gw7905-to-gw75xx.patch was
misnamed as that patch went upstream in 6.12 and thus is also removed
- 504-6.13-arm64-dts-imx-Add-i.MX8M-Plus-Gateworks-GW82XX-2X-support.patch
was refreshed to the final version that was accepted upstream
- 600-PCI-imx6-Start-link-at-max-gen-first-for-IMX8MM-and-IMX8MP.patch
was removed while I investigate an upstream approach for the issue
it was working around.
configs:
- config-6.12: unset new configs not needed for all cortexa7/a9/a53
- cortexa53/config-default: added new CONFIG_PCI_IMX6_HOST config for cortexA53 (IMX8M)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
They don't need +x permission.
Fixes: 502916468e ("ramips: add support for ASUS 4G-AX56")
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/19034
Signed-off-by: Nick Hainke <vincent@systemli.org>
This change moves common elements of the WR3000H and the WR3000S to mt7981b-cudy-wr3000-nand.dtsi.
This will simplify adding of new similar devices, for exapmle WR3000E.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18619
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rather than hardcoding the kernel/fdt addresses in the boot.scr script,
use the addresses provided by the bootloader.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
- refresh, rebase and reorder patches
- JH7110 media drivers have been dropped for now
- JH7110 E24 and mailbox drivers were added
- JH7100 DMA- and errata-patches have been dropped as they were
upstreamed
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
archs38 has been on life support for the last couple of releases,eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release.
Link: https://github.com/openwrt/openwrt/pull/19001
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow the armsr target to be built with a 6.12 kernel
when CONFIG_TESTING_KERNEL is set.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18849
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This includes both new additions to 6.12
and an attempted "refresh" of the config
to remove duplicates from target/generic/config-6.12.
(The OpenWrt kernel_makeoldconfig does not
work well with the armv8 subtarget for reasons
I am yet to determine, so that file has been
pruned manually)
Most new options are in armv8, where the
KConfig relates to a platform that will likely
be armsr compatible (like the i.MX91/93/95),
it has been enabled.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18849
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduced with Linux 6.7, in commit:
5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the mtdsplit_uimage driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
E.g. on Realtek devices that are booted for the first time through
initramfs with OpenWrt never installed before boot log will show
[ 0.932985] Creating 8 MTD partitions on "spi0.0":
[ 0.938412] 0x000000000000-0x000000080000 : "u-boot"
[ 0.990151] 0x000000080000-0x0000000c0000 : "u-boot-env"
[ 0.999907] 0x0000000c0000-0x000000100000 : "board-name"
[ 1.019971] 0x000000100000-0x000000e80000 : "firmware"
[ 1.051582] mtdsplit_uimage: no uImage found in "firmware"
[ 1.069365] 0x000000e80000-0x000001000000 : "kernel2"
[ 1.078959] 0x000001000000-0x000001040000 : "sysinfo"
[ 1.099747] 0x000001040000-0x000001c40000 : "rootfs2"
[ 1.119865] 0x000001c40000-0x000002000000 : "jffs2"
Similar issue was fixed before with commit ade045084b
("kernel: mtdsplit_minor: return 0 if not fatal")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19016
Signed-off-by: Robert Marko <robimarko@gmail.com>
GL.iNet shipped a hardware change of the WAN PHY going from the MaxLinear
GPY211C to the Airoha EN8811H.
Signed-off-by: Matthew Bilker <me@mbilker.us>
Link: https://github.com/openwrt/openwrt/pull/18799
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Trying to use modules for the PHY:s does not work:
The ethernet driver does not like to probe if it can't find
the PHY.
The ethernet driver really likes to be compiled-in. It will
not probe otherwise. Some hardware issue.
Revert things to how they always worked until I maybe solve
this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Extends SoC thermal sensor on rtl839x
* Tested on HP JG928A
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Link: https://github.com/openwrt/openwrt/pull/18825
Signed-off-by: Robert Marko <robimarko@gmail.com>
Regulators as implemented by the XHCI driver only accept one GPIO.
However, we can abuse the fact that the XHCI driver accepts two
regulators, one for 5V and the other for 3.3V, for USB 2 and 3 GPIOs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16967
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be done with so little effort, all but two patches are now
upstream. No need to keep support for v6.6, everything just works
the same or better with v6.12.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The resets in the GCC of the uniphy found in the IPQ5018 SoC are
incorrect which broke the ability to shift between 1G and 2.5G link
speeds. So let's correct the resets based on below two downstream
commits.
In a seperate and prequisite PR to the QCA-SSDK repo, logic has been
implemented to select the right reset based on the link setup so fixed
link scenarios don't break.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ahead of the actual fix in both the GCC and QCA-SSDK, add the required
AHB reset so it can be picked up by updated QCA-SSDK. This is needed
as the SSDK needs to use different resets depending on the link
architecture. If it's a fixed link, AHB needs to be reset. In a phy to
phy link setup (such as QCA8081), SYS, RX, and TX need to be reset using
one reset with a bitmask in the GCC (GCC_UNIPHY_SOFT_RESET).
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
With completely carving out GE PHY out of the QCA-SSDK, the named clock
references to the GE PHY RX and TX clocks are no longer needed.
So, let's revert to using the DT indices as per the upstream GCC driver.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use latest patches sent upstream for review for IPQ5018 GE PHY support:
- Move enablement of the LDO controller to the mdio-ipq4019 driver away
from the CMN PLL driver
- Remove the different patches to add CDT, MSE, AZ, and DAC support they
are all contained in the upstreamed driver.
Accordingly, also set the right property in the DTS for Linksys SPNMX56
to set the right DAC values to accommodate for the short cable length.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
kmod-fs-ntfs is not available on the 6.12 kernel.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18954
Signed-off-by: Robert Marko <robimarko@gmail.com>
As qualcommbe is now supported by the v6.12 kernel, there is no point
in v6.6 as well. Drop v6.6 support.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18982
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qualcommbe target was introduced after openwrt-24.10. The v6.12
kernel is now available, and is likely to be used by the next openwrt
release.While the v6.6 kernel served as an interim development vehicle,
it is no longer useful for the qualcommbe target
The v6.12 patches contain more recent submissions of pending ipq95xx
drivers. I expect that it will be much easier to update v6.12 patches
with new submissions. For ease of maintenance, it makes sense to use
a single kernel for qualcommbe.
For these reasons, enable v6.12 by default.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18982
Signed-off-by: Robert Marko <robimarko@gmail.com>
The external switch of the Huawei HG556a is a BCM5325E connected by MDIO.
All the DSA brcm legacy FCS tag and b53 patches have been submitted upstream
and will be backported when accepted.
There are still some sporadic FDB errors, but at least the switch is working
and stable on my device:
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 72:31:59:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 0 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to delete 72:31:59:xx:xx:xx vid 1 from fdb: -2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add support for V3 of the Engenius EWS2910P PoE switch. Like its v1
brother, This is an RTL8380 based switch with two SFP slots, and PoE
802.3af one every RJ-45 port.
Unlike its older brother, the max budget is 55W instead of 61.6 W.
Investigation into the communication protocol with the PoE controller
is ongoing, though it appears the vendor firmware configures the PSE
with a per-port budget of 30.0W.
Specifications:
---------------
* SoC: Realtek RTL8380M
* Flash: 32 MiB SPI flash Macronix MX25L25635E
* RAM: 256 MiB (As reported by bootloader)
* Ethernet: 8x 10/100/1000 Mbps with PoE
2x SFP slots
* Buttons: 1 "Reset" button on front panel
1 "LED mode: button on front panel
1 "On/Off" Toggle switch on the back
* Power: 48V-54V DC barrel jack
* UART: 1 serial header (JP1) with populated 2.54mm pitch header
Labeled GRTV for ground, rx, tx, and 3.3V respectively
* PoE: 1 STM ST32... microcontroller (U15)
1 RTL8238B PSE controller
Works:
------
- (8) RJ-45 ethernet ports
- Switch functions
- LEDs and buttons
Not yet enabled:
----------------
- Power-over-Ethernet (requires realtek-poe support for RTL8232B)
Install via web interface:
-------------------------
The factory firmware will accept and flash the initramfs image. It is
recommended to flash to "Partition 0". Flashing to "Partition 1" is
not supported at this point.
The factory web GUI will show the following warning:
" Warning: The firmware version is v0.00.00-c0.0.00
The firmware image you are uploading is older than the current
firmware of the switch. The device will reset back to default
settings. Are you sure you want to proceed?"
This is expected when flashing OpenWrt. After the initramfs image
boots, flash the -sysupgrade using either the commandline or LuCI.
Install via serial console/tftp:
--------------------------------
See commit 2cfaab4549 ("realtek: add support for EnGenius EWS2910P").
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15217
Signed-off-by: Robert Marko <robimarko@gmail.com>
When the Engenius EWS-2910P was added, only v1 was known. Move the
common parts to a dtsi, and split up the support to acccount for the
hardware version.
On v3, for example, the root partition uses a different uImage magic.
Add a "engenius,ews2910p-v1" compatible, while leaving the legacy
"engenius,ews2910p" to also mean v1.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15217
Signed-off-by: Robert Marko <robimarko@gmail.com>
DSA silently drops internal phy access to ports >= 32 in dsa_user_phy_read()
and dsa_user_phy_write(). The code shows:
static int dsa_user_phy_read(struct mii_bus *bus, int addr, int reg)
{
struct dsa_switch *ds = bus->priv;
if (ds->phys_mii_mask & (1 << addr))
return ds->ops->phy_read(ds, addr, reg);
return 0xffff;
}
With ds->phys_mii_mask being a 32 bit variable the reason is clear. So do
not only increase the max values but also adapt the needed bitmasks in
the dsa and phy code. This fixes the dsa_user_ports() and dsa_cpu_ports()
too.
While we are here combine the old separated patches because dsa, mdio and
phy are tigthly coupled.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18846
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PCS driver in the 6.12 patchset is the v5 submission (see link
below). It solves a number of issues and crashes with teh pcs driver
from the 6.6 patchset. However, this new driver is missing support for
"10gbase-r", "10g-qxgmii", and 1000/2500base-x modes.
Port these modes to the 6.12 patchset. "2500base-x" in particular seems
to be needed to establish a 2.5G link on phy-mode="usxgmii";
Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that patches for v6.12 are available, add the config, and enable
6.12 as a testing kernel.
Compared to v6.6 the patches to add "10gbase-r", "2500base-x",
"1000base-x", and "10g-qxgmii" modes have not been ported yet. They do
not apply cleanly to the new PCS driver. As the currently supported
hardware does not use those modes, it is not possible to test them at
this time.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Copy the v6.6 config to v6.6. It will be updated in a subsequent
commit in order to show the changes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Port reset and clock fixes from target/linux/qualcommbe/patches-6.6.
Modifications of v6.6 patches are noted in each commit body.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that ethernet is supported on IPQ9574, add the port nodes and
other requirements to enable ethernet on RDP433.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the second part of the PPE driver. This includes the EDMA and
network device support. This part does not appear to have been
officially submitted for upstream review. The series is taken from
target/linux/qualcommbe/patches-6.6, and had to be heavily modified
in order to compile of v6.12. Changes to patches are noted in the
respective patch body.
Also add the PPE and EDMA nodes in this series.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the v5 of the PCS patch. This is the latest submission as of this
writing. THe last four patches are not part of the submission. They
make the series work with v6.12 kernel, resolve a circular dependency
with the clocks, and add the DTS node. Include them as bundle.
Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
This driver is cherry-picked from target/linux/qualcommbe/patches-6.6.
While Qualcomm did submit past patches for QCA8084, the code has since
ben split from at803x. The existing OpenWRT version of the patch is
the cleanest version I could find. Add it here.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devicetree updates can work with the existing upstreamcode. They
do not require code changes. Add them before any code change.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add dts fixes from linux-next. Two patches from the NSSCC series are
still in -next did not yet land in mainline, as well as misc other DTS
changes. Add them here.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add relevant patches from upstream, up to v5.16-rc6. The gaps in the
patch numbersing are either patches that were picked into the stable
kernel (6.12.y), or that are already backported in
target/linux/generic. The gaps makes it easy for me to pick these
patches from my working kernel git branch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C6 v2 and add ipq-wifi package for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
RTC has been disabled so far in the cortexa53 subtarget so far, enable
it. It's also required for the crypto trng/prng drivers on these SoC
variants (to gather IOSC noise).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This symbol was lost when porting to the 6.12 kernel.
Fixes: 16b5a77716 ("mediatek: mt7629: update config-6.12")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18947
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All four subtargets build successfully and run under QEMU.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop obsolete symbols GCC_ASM_GOTO_OUTPUT_WORKAROUND and HW_CONSOLE, and
PREEMPT_NONE_BUILD which is now set in top-level generic config.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages were dropped off in reverted packaging, bring
them all back.
Link: https://github.com/openwrt/openwrt/pull/18952
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Update subtarget configs for kernel 6.12.
- Refresh patches for kernel 6.12.
- Drop 210-revert-macronix-nand-block-protection.patch since brcmnand no longer
implements low level ops.
- Adapt bcm63268 gpio switches for 6.12 numbering.
- Add b53 pending patches from Jonas Gorski to fix system hangs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit which aids following kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The support_eee patch is needed in order to prevent system hangs on bmips
devices.
c4f873c2b65c8 net: dsa: b53: mdio: add support for BCM53101
c86692fc2cb77 net: dsa: b53/bcm_sf2: implement .support_eee() method
f12b363887c70 net: dsa: use ethtool string helpers
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These patches are needed for b53 implementation of b53_support_eee, which
prevent system hangs on bmips devices.
99379f587278c net: dsa: provide implementation of .support_eee()
9723a77318b7c net: dsa: add hook to determine whether EEE is supported
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
