All targets using ar8327 use OF.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22069
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix execution of initramfs image on Huawei AP5030DN and AP6010DN by
increasing available memory for LZMA extraction by the loader.
The default leaves only ~23.6 MB between the decompression target
and the running loader code. Extracting images with built-in
packages lead to overwriting the loader code. This causes
the decompression to produce garbage output and hang.
Fix this by overwriting LZMA_TEXT_START to increase the
available memory for LZMA extraction to ~39.6 MB.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/22581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These targets seems to be left over, so changed as other targets
covered by commit d35d92a .
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/22510
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, devices having two cpu ports to the switch managed by swconfig,
especally those with qca955x, line tplink archer c7 v2 and linksys ea4500 v3,
use vlan on different cpu port to separate networks by default. (e.g. eth1.1
for lan, eth0.2 for wan)
However, untagging to these vlans cpu ports, and limiting vlans in the switch
on these devices could effectively offload the expense to process vlan tag from
cpu to the switch, and increase the throughput of lan <-> wan ipoe routing.
Tested on my tplink tl-wdr4900 v2, where ucidef_add_switch "switch0"
"0u@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6u@eth0" "1:wan" finally generates
on /etc/config/network:
config device
option name 'br-lan'
option type 'bridge'
list ports 'eth1'
config interface 'lan'
option device 'br-lan'
option proto 'static'
list ipaddr '192.168.1.1/24'
option ip6assign '60'
config interface 'wan'
option device 'eth0'
option proto 'dhcp'
config interface 'wan6'
option device 'eth0'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '2 3 4 5 0'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '1 6'
and the throughput of lan <-> wan ipoe routing with software flow offload
increases from around
[850 Mbps](https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500#nat_performance)
to 900 Mbps.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/19444
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bump compat version to 3.0 for TP-Link RE355 v1, RE450 v1 and RE450 v2.
Was missed for 25.12; users upgrading from older images need sysupgrade -F.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Misaligned rootfs_data caused config loss on sysupgrade. Set BLOCKSIZE
:= 4k for proper JFFS2 alignment. Add DEVICE_COMPAT_MESSAGE for
sysupgrade -F requirement.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rename Device/tplink_rex5x-v1 to tplink_rex5x. Make RE355 v1, RE450 v1,
and RE450 v2 inherit from it, removing duplicated fields from RE450 v2.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel patches with make target/linux/refresh for each target.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GPIO cascade driver is a downstream-only driver and the Buffalo
WZR-HP-G300NH is its only user for now. Recently, a similar and
independently developed driver 'gpio-line-mux `which serves the same
purpose was accepted upstream and backported here. Use that instead the
downstream driver.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of redifining the DEVICE_PACKAGES, make sure to expand the list
so yafut is included by default as well.
Fixes: 42cd486787 ("ath79: remove kmod-ath9k and wpad from Mikrotik RB750r2")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RB750r2 (HEXLite) does not have wifi and those packages bloat the image
by a significant amount. When building a custom image with WireGuard and
booting that from initramfs, there wasn't enough space left in tmpfs to
upload and flash the squashfs image. Investigating what packages I could
remove, I discovered these unneeded ones.
Signed-off-by: Eicke Herbertz <wolletd@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/22134
Signed-off-by: Robert Marko <robimarko@gmail.com>
NVMEM in UBI support has been present for a while. Use it to get the
MACs. Seems caldata needs to continue to be obtained through userspace.
This fixes label-mac-device as it needs a mac-address nvmem cell.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17068
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Linux kernel assumes that the u-boot environment covers the full
partition, but it only covers 0x1000 bytes. Linux checks the CRC and
does this over the full partition. This fails like this:
```
u-boot-env-layout 1f000000.spi:flash@0:partitions:partition@30000:nvmem-layout: Invalid calculated CRC32: 0xfcac8c41 (expected: 0x14e6335a)
u-boot-env-layout 1f000000.spi:flash@0:partitions:partition@30000:nvmem-layout: probe with driver u-boot-env-layout failed with error -22
```
Define the u-boot environment with a length of 0x1000 bytes to calculate
the CRC only over this area.
When replicating the u-boot environment with these parameters it
generates the same CRC:
```
mkenvimage -p 0 -b -s 0x1000 -o output.bin input.txt
```
Fixes: https://github.com/openwrt/openwrt/issues/21696
Fixes: 5e3a602def ("ath79: sitecom,wlrx100: use nvmem")
Link: https://github.com/openwrt/openwrt/pull/22030
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Though most Macronix Flash support the lock feature, the generic lock
implementation is not fully compatible with the Macronix series Flash.
Enabling the lock feature globally is unsafe. These hack patches are
used to unlock the Flash of ubnt devices on the ath79 target. Rework
these patches and move it to the ath79 target to prevent the potential
risk.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This header is deprecated and typically platform_device.h should be
used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21164
[Adapted the lantiq patches a bit]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a board file, add calibration variant for TP-Link
TL-WA1201 v2 and add ipq-wifi package for it.
Tested-by: Jim McDonald <122668301+jimmyd998@users.noreply.github.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add devm for ioremap to proper cleanup.
Test gpiod_direction_input for failure.
Remove rb91x_nand_release and fix wrong usage.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21165
Signed-off-by: Robert Marko <robimarko@gmail.com>
The EW71v2 has the WAN port configured at eth1.
The printed label-mac is configured on this iface in openwrt.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
This typo makes the script fail with:
-ash: /etc/hotplug.d/ieee80211/10_fix_wifi_mac: line 66: syntax error: unexpected word (expecting ")")
which ultimately prevents the mac address for certain devices wireless cards being set correctly
Signed-off-by: Nick French <nickfrench@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21287
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename them to follow the rtl836x driver gpiod changes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21143
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After merge of https://github.com/openwrt/openwrt/pull/20709 I noticed,
that https://mirror-03.infra.openwrt.org/snapshots/targets/ath79/tiny/
still does not contain the build for RE450.
I analyzed the problem and noticed, that only builds which fits into
original size can be build and if the image is larger, it fails with
the following error: "WARNING: Image file .../openwrt/build_dir/
target-mips_24kc_musl/linux-ath79_tiny/tmp/
openwrt-ath79-tiny-tplink_re450-v1-squashfs-sysupgrade.bin is too big:
> 7864320".
This error is quite misleading as the image is smaller than 7864320. The
reason for this error is that default tplink-safeloader has hardcoded
factory partition structure and fails to generate any file.
Rather then fixing tplink-safeloader I followed approach from commit
ebd5e5fb53 ("ramips: switched TP-Link RE305 v1 to new partition layout")
and switched away from "tplink-safeloader sysupgrade".
I did not include "IMAGES := sysupgrade.bin", because with tiny target it
is still possible to locally build even factory image.
Fixes commit e768731dc8 ("ath79: switch TP-Link RE355 v1, RE450 v1 and
RE450 v2 to mtd-concat").
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/21158
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Every attempt to update a device with NOR flash
and RouterBOOT v6 resulted in the error:
“RouterBOOT 6 and earlier requires ELF-in-YAFFS image.”
The cause was that xargs did not fully remove whitespace,
so the condition "$bootentry" != "kernel" always evaluated to true.
Signed-off-by: Marcin Maj <marcinmajsc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21034
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Also use led-sources for simplicity.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20508
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Also switch LED to led-sources for simplicity.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20529
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unneeded semicolon
WARNING comparing pointer to 0
WARNING: NULL check before some freeing functions is not needed.
WARNING: casting value returned by memory allocation function to (u32 *)
ERROR: allocation function on line 378 returns NULL not ERR_PTR on failure
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
This is a weird one. It should be using u-boot,env, but the variable
name is unknown. Keep it as is.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20520
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WF1200HP2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router with FE
ports, based on AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A-2.5BG2A)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EM2I-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 4x 10/100 Mbps
- switch : Atheros AR9344 (SoC)
- LEDs/Keys (GPIO) : 12x/4x
- note : all LEDs are controlled by ath10k chip (QCA9882)
- UART : through-hole on PCB (J1)
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8 (U-Boot: 115200n8)
- Power : 12 VDC, 0.7 A (Max. 8 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WF1200HP2 with router mode
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.10.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with sysupgrade.bin image
sysupgrade <sysuppgrade image>
8. Wait ~120 seconds to complete flashing and rebooting
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WF1200HP2 and interrupt bootloader by ESC key
3. Login to the bootloader CLI with the password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, backup the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the
device
9. Replace the bootloader with uboot.bin image (see above)
10. Perform sysupgrade with sysupgrade.bin image (see above)
11. Wait ~120 seconds to complete flashing and rebooting
Notes:
- The stock bootloader requires the unknown filesystem on firmware area
in the flash chip. Booting OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
Known issues:
- All LEDs on the front side are connected to the GPIO controller on the
ath10k chip (QCA9882) and controlled by it. The current ath10k driver
supports only one LED as "ath10k-phyN", but using as a GPIO controller
is not supported yet. As a result, all 12x LEDs on the front side
cannot be controlled by users.
MAC Addresses:
LAN : C0:25:A2:xx:xx:44 (config, 0x6 (hex))
WAN : C0:25:A2:xx:xx:45 (config, 0xc (hex))
2.4 GHz: C0:25:A2:xx:xx:46 (config, 0x0 (hex))
5 GHz : C0:25:A2:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20611
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WF1200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router with FE
ports, based on AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A-2.5BG2A)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EM2I-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 4x 10/100 Mbps
- switch : Atheros AR9344 (SoC)
- LEDs/Keys (GPIO) : 12x/4x
- note : all LEDs are controlled by ath10k chip (QCA9882)
- UART : through-hole on PCB (J1)
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8 (U-Boot: 115200n8)
- Power : 12 VDC, 0.7 A (Max. 8 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WF1200HP with router mode
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.10.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with sysupgrade.bin image
sysupgrade <sysuppgrade image>
8. Wait ~120 seconds to complete flashing and rebooting
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WF1200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with the password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, backup the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the
device
9. Replace the bootloader with uboot.bin image (see above)
10. Perform sysupgrade with sysupgrade.bin image (see above)
11. Wait ~120 seconds to complete flashing and rebooting
Notes:
- The stock bootloader requires the unknown filesystem on firmware area
in the flash chip. Booting OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
Known issues:
- All LEDs on the front side are connected to the GPIO controller on the
ath10k chip (QCA9882) and controlled by it. The current ath10k driver
supports only one LED as "ath10k-phyN", but using as a GPIO controller
is not supported yet. As a result, all 12x LEDs on the front side
cannot be controlled by users.
MAC Addresses:
LAN : C0:25:A2:xx:xx:44 (config, 0x6 (hex))
WAN : C0:25:A2:xx:xx:45 (config, 0xc (hex))
2.4 GHz: C0:25:A2:xx:xx:46 (config, 0x0 (hex))
5 GHz : C0:25:A2:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20611
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Moved pcie wifi nodes out of dtsi as these devices differ in wifi
chipsets and thus calibration size. Added compatible lines too.
Removed pointless label_mac assignments as label-mac-device is already
implemented.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19865
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since everything got migrated to the layouts driver, this is no longer
needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20948
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ath10k loads before ath9k and thus ends up as phy0.
Also use led-sources to avoid some confusion.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ath9k driver creates an ath9k LED by default. Instead of having a non
functional LED, configure it properly and remove the extra as it's not
needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All users of regular CONFIG_NVMEM_U_BOOOT_ENV have been converted to use
layouts.
CONFIG_NVMEM_U_BOOT_ENV selects the layout variant anyway so this is
safe to do.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With previous patches these devices have only 128 KiB less space than
RE450 v3. It may be even possible to revert commit 65b6f1c1b2 ("ath79:
move TP-Link RE450 v1 & v2 and RE355 v1 to tiny target") but that was
not done as the device has only 8 MiB flash and will eventually run out of
it anyway.
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch utilizes unused and empty flash space in the original partition
layout and increase maximum image size by 1664 KiB.
Tested on RE450v1 by running sysupgrade with build of size 5697 KiB and
checking that df shows 1988 1K-blocks for "/overlay".
Inspired by commit ebd5e5fb53 ("ramips: switched TP-Link RE305 v1 to new
partition layout").
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dump of content of my RE450 v1 showed, that there are valid data only
up to 0x10420. Everything after is just 0xFF. This will also make
partition table identical to qca9563_tplink_re450-v2.dts, which seems
to be logical.
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) currently comes up
with random MAC addresses. Assign the MAC addresses from hard_config for
LAN and WAN ports.
Fixes: c2140e32ce ("ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/20782
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Move calibration for pcie node out of dtsi. calibration size for ath10k
and ath9k differs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16231
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Use ath9k LED instead of specifying a generic one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16286
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Use ath9k LED binding to avoid generic LED usage.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16286
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v2 and add ipq-wifi package for it.
Tested-by: Semih Baskan <strstgs@gmail.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SPI chip select GPIO polarity is active low by default. We must
use "spi-cs-high" dts property to toggle the polarity. The polarity
on "cs-gpios" won't take effect at all[1]. Fix these incorrect GPIO
polarities to silence the kernel warnings.
[1] Refer to Linux/Documentation/devicetree/bindings/spi/spi-controller.yaml
```
device node | cs-gpio | CS pin state active | Note
================+===============+=====================+=====
spi-cs-high | - | H |
- | - | L |
spi-cs-high | ACTIVE_HIGH | H |
- | ACTIVE_HIGH | L | 1
spi-cs-high | ACTIVE_LOW | H | 2
- | ACTIVE_LOW | L |
Notes:
1) Should print a warning about polarity inversion.
Here it would be wise to avoid and define the gpio as
ACTIVE_LOW.
2) Should print a warning about polarity inversion
because ACTIVE_LOW is overridden by spi-cs-high.
Should be generally avoided and be replaced by
spi-cs-high + ACTIVE_HIGH.
```
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a useless property on ath79 target. Both spi-ar934x and
spi-ath79 drivers don't check num-cs property. They always set
chip select number to 3.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DTC recommends using wifi@0,0 as the node name to match the reg
property structure. Fix warning:
../dts/qca9557_fortinet_fap-221-c.dts:208.13-213.4: Warning (pci_device_reg): /ahb/pcie@180c0000/wifi@0,0,0: PCI unit address format error, expected "0,0"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C59 v1 and add ipq-wifi package for it.
Tested-by: Mateusz Jończyk <matjon@users.noreply.github.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a regression introduced by a recent commit.
It looks like a copy/paste error.
Add the missing line which defines the 'board' val
as it does not exist otherwise in the case check.
This fixes sysupgrade on ath79 MikroTik non-NOR boards.
Fixes: 318f07c231 ("ath79: mikrotik: check RouterBOOT version matching sysupgrade image")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
The latter is more descriptive in terms of what's going on.
Mostly found with
git grep gpios\ | grep 0\>
git grep gpios\ | grep 1\>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Also handle 2.4ghz LED in ath9k instead of generic.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Deprecated. Replaced with nvmem.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Check if the uploaded image matches the version of RouterBOOT before
proceeding with sysupgrade on MikroTik devices with NOR flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
RouterBOOT v7 for NOR devices does not support the historic yaffs
"kernel" ELF boot method.
Generate a compatible kernel
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Userspace handling is deprecated.
Also convert custom LED to one handled by ath9k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20112
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17344
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Move the mac address patch to 10_fix_wifi_mac.
This uses an AR9287, which uses a smaller size for its calibration.
The PCI ID is also wrong.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19864
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v1 and add ipq-wifi package for it.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19993
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of having two LED entries that supposedly control the same
thing, set the pin properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18905
Signed-off-by: Robert Marko <robimarko@gmail.com>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
The driver makes its own ath9k LED which handles everything.
Simplifies DTS slightly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20023
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling for this is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20023
Signed-off-by: Robert Marko <robimarko@gmail.com>
In first commit I successfully bring WAN port into ethernet switch,
without realizing that I was using custom bootloader. But if using
original bootloader it do not works. WAN port in original bootloader
is tied to using its own GMAC.
This fix is made so this firmware will be compatible with orignal
bootloader, so the user can directly flash from stock firmware without
changing anything.
Signed-off-by: Roy H <roy@altbytes.com>
Link: https://github.com/openwrt/openwrt/pull/20039
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Despite having the same tplink.dtsi file, there are differences in wifi
Move wifi nodes out of dtsi to make it clear what the chipset is and
what calibration size should be used.
While at it, change to use led-sources to simplify LED setup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20024
Signed-off-by: Robert Marko <robimarko@gmail.com>
They have the same 0x200 calibration size.
Added various compatible lines in various places to make it clear what
device we're talking about.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices use AR9285, which uses 1f8 as the calibration size, not
440 like newer chips do. Actually the driver mandates a minimum of 200.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add calibration variant and ipq-wifi package for Xiaomi AIoT AC2350
Signed-off-by: Igor Dyatlov <dyatlov.igor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19707
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
It's also a bit funny matching against phy0 and phy1 when both differ
between ath9k and ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19862
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18904
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k documentation says to use pci168c strings for the compatible
string, probably because the OWL loader uses it to overide bogus pci IDs
like abcd. This is not the case with ath10k and the documentation
explicitly states to use qcom,ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18920
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device does not come with a pci card. It has a slot where one can
get supplied. What's more, nvmem or ieee80211 frequency limits are not
applied here. It can just get removed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18920
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18906
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18908
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Set the pcie device to qcom,ath10k as the Documentation says, The pci
line implies it's ath9k when it's actually ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18873
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18873
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move append-teltonika-metadata to image-commands.mk and unify over different targets.
This method can be used to create valid "factory" images for most of Teltonika devices.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19401
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Zoltan HERPAI wigyori@uid0.hu
Link: https://github.com/openwrt/openwrt/pull/18907
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
