Restore CONFIG_PAGE_BLOCK_MAX_ORDER=10 in ramips 6.18 config fragments
to fix build failures where PAGE_BLOCK_MAX_ORDER was undefined.
Support for Linux 6.18 on ramips was added after this OpenWrt change:
ac0cb87a45.
Before that integration, the kernel option CONFIG_PAGE_BLOCK_MAX_ORDER=10
was provided in target/linux/generic/config-6.18 and applied broadly.
After the ramips 6.18 integration the generic fragment no longer supplied
this option for ramips targets, which caused some backported code paths
and drivers to assume PAGE_BLOCK_MAX_ORDER was defined and led
to compilation failures.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22831
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ramips now supports 6.18 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MODULE_DEVICE_TABLE macro was using an incorrect parameter 'match'
instead of the actual device table name 'mt7621_nfc_id_table'.
This fixes the reference to use the correct symbol name, ensuring
proper device table registration for module autoloading.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix fe_clean_rx to handle the changed frag_cache layout on newer kernels.
For kernels >= 6.13 the fragment cache needs to be converted from its
encoded_page value instead of using the old va field. Add an ifdef
to use frag_cache.encoded_page & PAGE_MASK and virt_to_page for those
kernels, keep the old path for older kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refreshed patches for ramips/patches-6.18 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace previous bgpio_init usage with a full gpio_chip registration so the driver
integrates cleanly with the kernel GPIO core.
Add drivers/gpio/gpio-ralink.c implementing a gpio_chip with:
- get/set, direction_input/direction_output, get_direction
- get_multiple/set_multiple to support efficient multi-bit ops
- DT handling for determining ngpios (reads "ngpios" or falls back to gpio-ranges)
- MAX_NGPIOS cap and safe defaults
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update patch 831-03-mmc-mtk-sd-use-default-PATCH_BIT1-2-values-for-mt762.patch
to a newer version compatible with kernel 6.18.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove symbols no longer present in version 6.18,
add new 6.18 kernel symbols.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
This symbol is selected by CONFIG_BPF, which was already enabled
on generic config-6.12.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the Wavlink "Halo Base Pro".
SOC: MT7621DAT
RAM: 128MiB
Flash: 16MiB NOR
WiFi: MT7603EN + MT7613BEN
Buttons:
- The touch sensor was originally for WPS, but this has been moved to the
pair button which is no longer used to prevent accidental touches
LEDs:
- On original firmware, the status LEDs light up as follows:
- Purple = booting, Blue = working, Red = error
Partitions:
- factory contains unique WiFi EEPROM and default MAC addresses
- vendor partition has an unknown purpose
Stock MAC address allocation:
- LAN1: xx:xx:xx:xx:xx:80
- LAN2/WAN: xx:xx:xx:xx:xx:81
- WiFi 2.4G: xx:xx:xx:xx:xx:82
- WiFi 5G: xx:xx:xx:xx:xx:83
LAN Ports:
- lan1 is the normal white LAN port
- lan2 is labelled "LAN/Backhaul", which can either be LAN or WAN.
- Since this device is intended to be part of a mesh, this will usually
be a LAN port, hence why it's assigned to lan2 here
Notes:
- I've chosen "Halo Base Pro" as the device model, despite the website URL
showing WL-WN535M3, as the label only states "Halo Base Pro".
- Only the 5GHz WiFi address is labelled on the device
Signed-off-by: William Latter <williamlatter77@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22400
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compared to the "mediatek,mt8173-xhci", this is a more generic and
reasonable compatible string. On the driver side, they are identical.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The USB t-phy driver includes some magic register init values. This
should be beneficial for the USB stability and performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MT7621 USB phys are compatible with the MediaTek T-PHY controller.
The vendor SDK also enabled this driver for MT7621.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit a2fa1db797.
These patches stop secondary CPUs before restart and wait for them
to go offline, fixing the mt7621 reboot deadlock without needing to
disable CONFIG_LIST_HARDENED.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/22724
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Z-ROUTER ZR-2662 (also known as Routerich
AX1800 V2) wireless WiFi 6 router.
Hardware specification
---------------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Note: This device is similar to Z-ROUTER ZR-2660, but with minor hardware
revisions. The firmware and configuration are compatible.
Signed-off-by: xingchi <juncaixingchi2026@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21524
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB NOR
- RAM: 64 MiB DDR2
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN/LAN, 1x 10/100 LAN (MT7628)
- Build-in LTE Modem: MeigLink SLM770A
4G Cat. 4 (150/50 Mbps)
- Buttons: 1x Reset, 1x wps
- LEDs: Front: 1x Red, 1x White,
Back: 3x White 4G signal strengh
- Serial console: unpopulated header, 115200 8n1
- Power: USB-C
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Migration to OpenWrt:
- Download the RSA signed intermediate firmware from the Cudy website:
`openwrt-ramips-mt76x8-cudy_lt300-v3-squashfs-flash.bin`
- Connect computer to LAN and flash the intermediate firmware via OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The dt-bindings suggest using "^serial(@.*)?$" as the node name.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is necessary to make it work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
<>, <> is the preferred way to specify multiple entries.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove unnecessary properties as there is no
reg property in child node.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22592
Signed-off-by: Robert Marko <robimarko@gmail.com>
It appears that CONFIG_LIST_HARDENED causes the system to
hang when restarted. I was unable to determine the cause
of the crash so disabling CONFIG_LIST_HARDENED seems like
an acceptable workaround for the time being.
The issue only occurs on reboot.
Fixes: https://github.com/openwrt/openwrt/issues/20099
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/22672
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Xiaomi Redmi/Mi Router AC2100 does have the correct label mac on the WAN interface.
This MAC is available as gmac1.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/22567
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adjust the memory remap range according to the mt7621 programming
guide to ensure that the driver can correctly access the peripheral
registers.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22467
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel load address was changed in commit e2d823d068 ("ramips:
fix LZMA decompression error for TP-Link EAP615-Wall"). We also need
to relocate the load address for initramfs image so that it can be
booted correctly.
Fixes: e2d823d068 ("ramips: fix LZMA decompression error for TP-Link EAP615-Wall")
Fixes: https://github.com/openwrt/openwrt/issues/22505
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22562
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The issue described in the patch has been fixed by commit
604355e8c4 ("kernel: fix fraglist GRO on linux 6.12")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22525
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The initial mt76x8 kernel config file was inherited from mt7620
sub-target. However, This SoC series doesn't support any external
PHY. We can disable CONFIG_ICPLUS_PHY symbol to reduce kernel size.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22519
Signed-off-by: Robert Marko <robimarko@gmail.com>
A size of 600 is incomplete in that calibration data is not included,
resulting in low TX power.
Fixes: 64dae105 ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22459
Signed-off-by: Robert Marko <robimarko@gmail.com>
The dtsi used handles a bunch of non-DBDC platforms where the
assignments are correct. The 3040-a1 is different as there are 3 instead
of 2 wifi interfaces and WAN needs to be incremented by 1.
Remove userspace wifi assignmwent which was needed before per band nvmem
was supported.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21977
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set nand flash for KN-1910
Sysupgrade or any other method i tried (asu, owut) not working without it. Tested with a local build.
Signed-off-by: Esat Yiğithan GÖKTOPRAK <eygoktoprak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22311
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The bootcount init script is missing the executable bit (644 instead of 755),
causing the script to not be executable:
/etc/preinit: line 44: /etc/init.d/bootcount: Permission denied
Fixes: c3b8108a2b ("ramips: Add support for Xiaomi MiWiFi 3A")
Signed-off-by: Oliver Sedlbauer <os@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/22446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Developers no longer maintain this driver. And it has been replaced
by the new upstream implementation. It's time to say goodbye.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22214
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is the generic PWM framework driver for Mediatek SoC. Now
this module is ready for MT7628.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22214
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The upstream MediaTek PWM driver requires these clock sources to
work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22214
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Since the u-boot ethaddr variable is quoted, we cannot use it.
Use mac-base instead to specify in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Removes deprecated userspace handling.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some MT7621 devices also have I2C peripherals.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22213
Signed-off-by: Robert Marko <robimarko@gmail.com>
