This downstream patch fixes a bug which could flood the logs with the
following message and would eventually lead to a crash.
ath11k c000000.wifi: failed to send HAL_REO_CMD_UPDATE_RX_QUEUE cmd, tid 0 (-105)
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: MX2000: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
MX5500: QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCN6122 platform support.
QCN6122 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
As such, QCN6122 is a hybrid bus type device and follows the same codepath
as for WCN6750.
This is a reversed engineered and heavily simplified version of below
downstream patch:
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/ \
blob/NHSS.QSDK.12.4.5.r2/mac80211/patches/232-ath11k-qcn6122-support.patch
Co-developed-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for QCN6122.
QCN6122 is specific/exclusive to the IPQ5018 platform and firmware
files are publishes in a subdirectory of the IPQ5018 firmware files.
While at it, add support for packaging BDFs for QCN6122 wifi and
update iwinfo to recognize QCN6122 wifi.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
IPQ5018 uses different BDF and caldb addresses for vairous boards,
so let's support reading these addresses from the device tree.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for IPQ5018.
As part of commit 172ccf7, the source is pointed to the new QCA repo.
Until QCA publishes updated firmware for IPQ5018 and QCN6122, we need
to download the firmware from the old QUIC repo. As such, add a new
download routine for IPQ5018/QCN6122 to fetch the firmware files from
the old repo.
While at it, add support for packaging BDFs for IPQ5018-based boards
and update iwinfo to recognize IPQ5018 wifi.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Qualcomm IPQ50xx in the QCA NSS dataplane driver.
The QCA implementation uses depracated DMA api calls and a downstream SCM
call, so convert to proper Linux DMA and SCM api calls.
In addition, add fixed-link support to support SGMII which is used to
connect the internal IPQ50xx switch to an external switch (ex. QCA8337)
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
The codename for IPQ50xx is Maple (abbreviated as 'MP'), so let's pass
the codename to allow the QCA-SSDK to build for the IPQ50xx SoC.
In addition, disable compiling the MP_PHY driver in favor of a native
driver being upstreamed.
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
The three packages base-files, libc and kernel are special, the former
can't be upgraded in place since it's content are modified on startup,
the latter two are virtual packages only used as constraints for the
package manager.
Historically base-files was "locked" via a special OPKG function, the
latter two were hidden from the package index and thereby never picked
as possible upgrade.
Time moved forward and we now have APK and tools like OWUT. The latter
compares available packages with installed packages and generates user
readable output, requiring versions for libc and kernel, too. At the
same time, APK uses a different looking mechanism, which is set during
installation instead of part of the package metadata.
In short, this patch adds version constraints to the three packages,
allowing them to be part of the package index.
Fixes: #17774Fixes: #17775Fixes: efahl/owut#31
Signed-off-by: Paul Spooren <mail@aparcar.org>
This new value points to where firmware can be downloaded. It's not
about a single release but all available firmware releases.
In the next step, this URL should be exposed via `ubus call system
board` as an entry of the `distribution` field. With that value, the
running firmware can check for newer releases.
We already have VERSION_REPO however that's different and only meant for
package managers to download their fitting package indexes/packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/17780
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update URL variable to reflect switch to Github for development
The old URL returns HTTP 404
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/17752
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add new option to be able to perform upgrade on current partition for dual firmware devices:
"-s stay on current partition (for dual firmware devices)"
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
The syntax error prevented the correct creation of all ipq60xx U-Boot environment files: /etc/config/ubootenv and /etc/fw_env.config
Signed-off-by: Ivan Deng <hongba@rocketmail.com>
Link: https://github.com/openwrt/openwrt/pull/17755
Signed-off-by: Robert Marko <robimarko@gmail.com>
322500403615 service: add default group @ to match all nodes
5f7860306200 ubus: rename unetd_ubus_notify to unetd_ubus_network_notify
d13752814651 enroll: add PEX sub-protocol to support enrolling new nodes into a network
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The USB PHY on the ar9330 and similar SoCs needs the PHY driver. In
OpenWrt 23.05 it was compiled into the kernel. The kernel 6.6
configuration does not compile it in any more, make the
kmod-usb-chipidea driver select it to add it to the images.
Fixes: https://github.com/openwrt/openwrt/issues/17710
Fixes: 04bdf9b332 ("ath79: disable ath79 USB phy drivers by default")
Link: https://github.com/openwrt/openwrt/pull/17720
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
atm_qos struct should be the same both for user and kernel spaces. Via
the __SO_ENCODE() macro it is used to define the SO_ATMQOS socket IOC.
During the VRX518 support introduction, the atm_trafprm sturct nested
into the atm_qos stucture was update with newer fields that are
referenced by the ATM TC layer of the VRX518 TC driver. These new fields
are intended to communicate information for extra traffic classes
supported by the driver. But we are still using vanilla kernel headers
to build the toolchain. Due to the atm.h header incoherency br2684ctl
from linux-atm tools is incapable to configure the ATM bridge netdev:
br2684ctl: Interface "dsl0" created sucessfully
br2684ctl: Communicating over ATM 0.1.2, encapsulation: LLC
br2684ctl: setsockopt SO_ATMQOS 22 <-- EINVAL errno
br2684ctl: Fatal: failed to connect on socket; File descriptor in bad state
There are two options to fix this incoherency. (a) update the header
file in the toolchain to build linux-atm against updated atm_trafprm and
atm_qos structures, or (b) revert atm_trafprm changes.
Since there are no actual users of the extra ATM QoS traffic classes,
just drop these extra traffic classes from vrx518_tc ATM TC layer and
drop the kernel patch updating atm.h.
Besides fixing the compatibility with linux-atm tools, removing the
kernel patch should simplify kernel updates removing unneeded burden of
maintenance.
Run tested with FRITZ!Box 7530 with disabled extra traffic classes and
then removed them entirely before the submission.
CC: John Crispin <john@phrozen.org>
Fixes: cfd42a0098 ("ipq40xx: add Intel/Lantiq ATM hacks")
Suggested-by: Andre Heider <a.heider@gmail.com>
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-4-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ATM TC layer have some issues which effectively prevent VRX518 from
being used as ADSL modem. Specifically, there one crash during the ATM
layer configuration and wrong PVC ID selection on packet receiving what
breaks RX path. Fix both of the issues. Make subif iface registration
optional to prevent the crash (see more details in the new patch) and
update the hardcoded PVC ID to match the first allocated channel.
Run tested with FRITZ!Box 7530.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-3-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It looks like VRX518 returns phys addr of data buffer in the 'data_ptr'
field of the RX descriptor and an actual data offset within the buffer
in the 'byte_off' field. In order to map the phys address back to
virtual we need the original phys address of the allocated buffer.
In the same driver applies offset to phys address before the mapping,
what leads to WARN_ON triggering in plat_mem_virt() function with
subsequent kernel panic:
WARNING: CPU: 0 PID: 0 at .../sw_plat.c:764 0xbf306cd0 [vrx518_tc@8af9f5d0+0x25000]
...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = aff5701e
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Noticed in ATM mode, when chip always returns byte_off = 4.
In order to fix the issue, pass the phys address to plat_mem_virt() as
is and apply byte_off later for proper DMA syncing and on mapped virtual
address when copying RXed data into the skb.
Run tested with FRITZ!Box 7530 on both ADSL and VDSL (thanks Jan) links.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Tested-by: Jan Hoffmann <jan@3e8.eu> # VDSL link
Reported-and-tested-by: nebibigon93@yandex.ru # ADSL link
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-2-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These symbols are needed to satisfy lxc dependencies.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17553
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
047b2efc1348 CMakeLists.txt: bump minimum cmake version
16ff0badbde7 CMakeLists: add support for including ABIVERSION in the library version number
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Increase PKG_RELEASE as follow-up for
("lantiq: fritz_cal_extract with reverse option for AVM FritzBox 7430").
Signed-off-by: Robert Marko <robimarko@gmail.com>
This implementation of fritz_cal_extract can also retrieve firmware
data stored in reverse byte order, as found in the AVM 7430 device.
This is done by intermediate storage in a buffer presumably large enough
to hold the complete data set. Currently, this buffer size is 128kB + 1kB
(some extra space for skipped data).
In the usual case of "forward" data, this implementation should behave
like the original implementation in all common cases. limit [-l] will
determine the amount of data read and size of buffer allocated.
However, if you are reading reversed data or didn't set a limit, the buffer
may be too small to hold all data. In this case, you can choose a higher
limit [-l] to enforce a sufficient buffer size.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Link: https://github.com/openwrt/openwrt/pull/15501
Signed-off-by: Robert Marko <robimarko@gmail.com>
Version 6.11 - October 8, 2024
* Feature: cmis: print active and inactive firmware versions
* Feature: flash transceiver module firmware (--flash-module-firmware)
* Feature: add T1BRR 10Mb/s mode to link mode tables
* Feature: support for disabling netlink from command line
* Fix: fix lanes parameter format specifier
* Fix: add missing clause 33 PSE manual description
* Fix: qsf: Better handling of Page A2h netlink read failure
* Fix: rss: retrieve ring count using ETHTOOL_GRXRINGS ioctl (-x)
* Misc: man page formatting fix
* changelog here: https://git.kernel.org/pub/scm/network/ethtool/ethtool.git/commit/NEWS?id=c0ea4b70c71334ef038f7a3416b228a50dada406
Tested on gl.inet MT6000, retrieve ring count is now working
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17607
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update handling of macro __assign_str() to also support the one-argument
variant when building against kernel 6.10 or later. This is needed for
building the next LTS kernel 6.12.
Fixes: 384d079fd8 ("mac80211: update to version 6.11")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17456
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some platforms a single ethernet device for all ports with multiple rx rings
and NAPI threading enabled. In this case, the steering script was limiting
performance by keeping all NAPI threads assigned to the same CPU.
Fix this by assigning each rx queue and the corresponding NAPI task separately.
Additionally, if the number of rx queues is at least as big as the number of
CPUs, skip weight based assignment and distribute the load across all CPUs
directly.
Fixes: https://github.com/openwrt/openwrt/issues/17611
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Envtools can automatically detect the number of blocks.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17463
Signed-off-by: Robert Marko <robimarko@gmail.com>
The lldp_class and lldp_location config option are only valid when
compiled with LLDP-MED support. If not they will cause lldpd not to
start.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17571
Signed-off-by: Robert Marko <robimarko@gmail.com>
It needs to be opt-in instead of opt-out, since there is no reliable way to
determine if the extra background radar chain has an antenna connected.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Change the double-include guard to avoid conflict with the linux kernel header
Reported-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changes (breaking):
- Remove support for building 802.3bt TLVs (broken).
Fix:
- Fix memory leaks in EDP/FDP decoding when receiving some TLVs twice.
- Do not set interface description continuously.
- Use a different Netlink socket for changes and queries.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17570
Signed-off-by: Robert Marko <robimarko@gmail.com>
Without this patch, we get the following error:
Mon Dec 23 11:35:44 2024 daemon.err hostapd: nl80211: kernel reports: integer out of range
As updating hostapd would be too complex and requires further testing,
we backport this simple upstream fix instead.
Fixes: https://github.com/openwrt/openwrt/issues/16680
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17590
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Update to latest version. There are no patches that need to be
refreshed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17538
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is
wall or pole mountable, and rated for outdoor use. It can only be
powered via PoE.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: ESMT PSR1GA30DT 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap610-outdoor-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
The tplink2022 image format
============================
The vendor images of this device are packaged in a format that does
not match any previous tplink formats. In order for flashing to work
from the vendor's web UI, firmware updates need to be packaged in
this format. The `tplink-mkimage-2022.py` is provided for this
purpose.
This script can also analyze vendor images, and extract the required
"support" string. This string is checked by the vendor firmware, and
images with a missing or incorrect string are rejected.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14922
Signed-off-by: Robert Marko <robimarko@gmail.com>
This was the first DSA packaged, and the tagger was made into
a separate package. This is too complicated: the mv88e6xxx
is the only module using this tagger after all, fold the module
for the DSA hardware and the driver for the tagger into a
single package and let modprobe do its job of probing the
tagger for the driver.
Tested on the BMIPS Inteno XG6846.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250110-mv88e6xxx-single-package-v1-1-223ad7fb312e@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.
Signed-off-by: David Bauer <mail@david-bauer.net>
It is not required to specify the number of blocks as envtools are able
to autodetect it.
Link: https://github.com/openwrt/openwrt/pull/17504
Signed-off-by: Robert Marko <robimarko@gmail.com>
Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.
Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is a minor upgrade that mainly fixes some compilation errors
and remove old unused code.
The Makefile has been reorganized. Now all package make parameters
are passed as configure arguments instead of environment variables.
The compilation dependencies remain the same as ppp v2.5.1 and the
package size changes are negligible.
Change log:
https://github.com/ppp-project/ppp/blob/v2.5.2/README#L70
Upstreamed patches:
101-pppd-crypto-fix-build-without-openssl.patch [1]
102-pppd-make-pid-directory-before-create-the-pid-file.patch [2]
103-pppd-crypto-fix-gcc-14-build.patch [3]
[1] 5f6eabdb66
[2] 734bc0438e
[3] ac269dbf7c
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17477
Signed-off-by: Nick Hainke <vincent@systemli.org>
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11 which is included here.
The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns
If the led node is present in the controller then the channel is
set to active.
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
Spaces and tabs are widely used in variable definitions. We have to
remove them to ensure that get_mac_ascii() works properly.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The function get_mac_ascii() will fail when there are two or more
same MAC address variable names in the mtd partition. Only retain
the first variable to workaround this rare situation.
Fixes: https://github.com/openwrt/openwrt/issues/17236
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The u-boot LED command "led_loop_done" is missing from the OpenWrt
One NAND flash u-boot. Copy it from the OpenWrt One NOR flash u-boot
default environment to fix this issue.
Fixes: https://github.com/openwrt/openwrt/issues/17310
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that the original patch has been manually modified. The
newly added line number is incorrect.
Fixes: c0581520b1 ("uboot-mediatek: add Routerich AX3000 support")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On some drivers, setting the tx power on the interface is not enough.
Set it for the phy as well.
Fixes: 04fb05914e ("wifi-scripts: add multi-radio config support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
35bcf68a6297 wifi: mt76: scan: fix setting tx_info fields
4d8d6e2e7710 wifi: mt76: scan: set vif offchannel link for scanning/roc
e354436db440 wifi: mt76: mt7996: use the correct vif link for scanning/roc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
d996988ae55b libubus: close file descriptor after sending it from a request
afa57cce0aff libubus: add support for using channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check the return value of malloc and pread in case they fail.
Signed-off-by: Qiyuan Zhang <zhang.github@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a bug in linksys_bootcount.c that resetbc won't work on nand
with min I/O size> 2048.
Check the boot-log entry's intergrity with checksum.
Signed-off-by: Qiyuan Zhang <zhang.github@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Missing limits.h. Upstream backport.
Add extra backports. Replace Alpine Linux patch with upstream one. Same
with patch 400.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17426
Signed-off-by: Robert Marko <robimarko@gmail.com>
109114146f9c mt76: only enable tx worker after setting the channel
5fe42ec88fd1 mt76: mt7915: ensure that only one sta entry is active per mac address
1884f568ba02 wifi: mt76: do not add wcid entries to sta poll list during MCU reset
71fa9124d107 wifi: mt76: mt7996: fix NULL pointer dereference in mt7996_mcu_sta_bfer_he
eb85bb3fd5bf wifi: mt76: mt7915: fix eifs value on older chipsets
83e4d4a82e65 wifi: mt76: introduce mt792x_config_mac_addr_list routine
b47e20b440ae wifi: mt76: mt7925: fix NULL deref check in mt7925_change_vif_links
3e3c484726f3 wifi: mt76: mt7925: fix wrong band_idx setting when enable sniffer mode
3f1401a0f035 wifi: mt76: mt7925: fix get wrong chip cap from incorrect pointer
eede99f524e8 wifi: mt76: mt7925: fix the invalid ip address for arp offload
c99e4d51b340 wifi: mt76: mt7996: fix overflows seen when writing limit attributes
af983b2543ed wifi: mt76: mt7915: fix overflows seen when writing limit attributes
af494e2dcc94 wifi: mt76: mt7915: exclude tx backoff time from airtime
6f6a1f7cb381 wifi: mt76: mt7996: exclude tx backoff time from airtime
7f65b1b28b4c wifi: mt76: connac: Extend mt76_connac_mcu_uni_add_dev for MLO
1b5e6abc2e7a wifi: mt76: mt7925: Fix incorrect MLD address in bss_mld_tlv for MLO support
72b4688b3912 wifi: mt76: mt7925: Fix incorrect WCID assignment for MLO
6bd2c044e67a wifi: mt76: mt7925: Fix incorrect WCID phy_idx assignment
1c04e9693466 wifi: mt76: mt7925: fix wrong parameter for related cmd of chan info
01e02947bdbf wifi: mt76: mt7925: Fix CNM Timeout with Single Active Link in MLO
b90b1a1dc71b wifi: mt76: mt7925: Enhance mt7925_mac_link_bss_add to support MLO
53ec7a551f17 wifi: mt76: Enhance mt7925_mac_link_sta_add to support MLO
3c99ef40e0e7 wifi: mt76: mt7925: Update mt7925_mcu_sta_update for BC in ASSOC state
285efc6afaec wifi: mt76: mt7925: Update mt792x_rx_get_wcid for per-link STA
e5c0d1289e6c wifi: mt76: mt7925: Update mt7925_unassign_vif_chanctx for per-link BSS
67dcd5c888c4 wifi: mt76: mt7925: Update secondary link PS flow
fd4d6f87072f wifi: mt76: mt7925: Init secondary link PM state
6d972b5b9d6a wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO
3acc6cbb9556 wifi: mt76: mt7925: Cleanup MLO settings post-disconnection
0aab0c61ce92 wifi: mt76: mt7925: Properly handle responses for commands with events
15bead1b0041 wifi: mt76: do not hold queue lock during initial rx buffer alloc
732044a949d5 wifi: mt76: mt7925: config the dwell time by firmware
9ba311ec6afa wifi: mt76: mt7921: introduce CSA support
5d12c7404c22 wifi: mt76: mt7921: add rfkill_poll for hardware rfkill
ef965d408b79 wifi: mt76: mt7925: replace zero-length array with flexible-array member
f8563589c72d wifi: mt76: mt7921u: Add VID/PID for TP-Link TXE50UH
Signed-off-by: Felix Fietkau <nbd@nbd.name>
They show up as null entries in the nl80211 wiphy dump.
Fixes the following error:
Reference error: left-hand side expression is null
In find_phy(), file /usr/share/ucode/iwinfo.uc, line 19, byte 11:
called from function get_max_power (/usr/share/ucode/iwinfo.uc:42:32)
called from function module (/usr/share/ucode/iwinfo.uc:102:39)
called from anonymous function (/usr/bin/iwinfo:5:25)
` if (phy.wiphy == wiphy)`
Near here ------^
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When doing LTO builds, the target related CFLAGS need to be passed to the
linker, so that they are considered for target code generation.
Pass TARGET_CFLAGS in EXTRA_LDFLAGS to ensure that this is handled properly.
Fixes: #17200
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update to the latest upstream release to include recent improvements and
bugfixes, and simplify use of PKG_SOURCE_VERSION.
This version supports BPF objects of either endianness, allowing for
introspection, linking and skeleton creation, and enables cross-compiling
modern BPF applications for targets with non-native byteorder.
Link: https://github.com/libbpf/bpftool/releases/tag/v7.5.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17404
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add support for saving list of installed packages for APK in the same way
we do it for OPKG.
Unlike OPKG, we dont generate .control files for packages so lets use .list
files instead.
Fixes: #16947
Link: https://github.com/openwrt/openwrt/pull/17123
Signed-off-by: Robert Marko <robimarko@gmail.com>
Simplify patch with gpiochip_add_data, struct reduction, new GPIO API,
and header cleanup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
This goes away in kernel 6.12 upstream.
Get ahead of the curve by fixing all the local patches as well.
Get rid of CONFIG_OF. It's needed now.
Refreshed all patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix bogus reference to kmod-nf-conntrack-timeout, fixing the warning
`WARNING: Makefile 'package/kernel/linux/Makefile' has a dependency on
'kmod-nf-conntrack-timeout', which does not exist`.
Fixes: 0e2dcfc4f4 ("netfilter: add kmod-nfnetlink-ct{helper,timeout}")
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/17388
Signed-off-by: Robert Marko <robimarko@gmail.com>
- drop patches accepted upstream
- include build fixes in the tarball
- based on https://github.com/nbd168/backports commit 410656ef04d2
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Not needed. Everything can be replaced with devm.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shorter and more consistent with other drivers.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
I have no idea why this is even here. Simplifies the code with direct
returns.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Not needed as all the older kernels are gone.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file does not use a coding style consistent with the kernel. Run
clang-format with the kernel's .clang-format file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1)
- 3 buttons (WPS, reset, LED on/off)
- 1x 2.5 Gbit WAN port with Maxlinear GPY211C
- 4x 1 Gbit LAN ports
Disassembly:
- There are five screws at the bottom: 2 under the rubber feet, 3 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes next to/under the antenna cables.
- Note that there is another set of 4 pin holes on the side of the board, it's not used.
- Pins (from front to rear):
- 3.3V (do not connect)
- TX
- RX
- GND
- Settings: 115200, 8N1
MAC addresses:
- MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52)
- MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53)
- WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52)
- LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53)
- WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54)
- WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57)
Flashing via OEM web interface:
- Currently not supported because image crypto is not known
Flashing via recovery web interface:
- This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition
- Use a Chromium based browser, otherwise firmware upgrade might not work
- Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red
- Upload the recovery image, this will take some time. LED will continue flashing red during the update process
- The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing
- If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case:
- Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image)
- Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60
- OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface)
- Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used
Flashing via Initramfs:
- Before switching to OpenWrt, ensure that both partitions contain OEM firmware.
- This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface.
- Flashing via OEM web interface will automatically flash the currently not active partition.
- Open router, connect serial interface
- Start a TFTP server at 192.168.200.2 and provide the initramfs image there
- When starting the router, select "7. Load Image" in U-Boot
- Settings for load address, load method can be kept as they are
- Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2)
- Enter the file name of the initramfs image
- Confirm "Run loaded data now?" question after loading the image with "Y"
- OpenWrt initramfs will start now
- Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM
- Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0
- During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition
Reverting back to OEM:
- Boot the initramfs image as described in "Flashing via Initramfs" above
- Copy the backed up ubi partition to /tmp (e.g. by using SCP)
- Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4
- Reboot the device, OEM firmware will start now
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17296
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Referencing commit a1837135e0
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Nanya NT5TU64M16HG-AC)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
BUTTON: Reset - WPS - "Router" switch
LED: 2x system-LED, 2x wlan-LED, 1x internet-LED,
2x routing-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label cc:e1:d5:xx:xx:ed art@macaddr_wan
lan cc:e1:d5:xx:xx:ec art@macaddr_lan
wan cc:e1:d5:xx:xx:ed $label
WiFi4_2G cc:e1:d5:xx:xx:ec art@cal_ath9k
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.11.10/24
to the ethernet port. Serve the OpenWrt initramfs image as
"openwrt.bin"
3. Boot the initramfs image using U-Boot
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm 0x84000000
4. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Installation from Web Interface
------------
To flash just do a firmware upgrade from the stock firmware (Buffalo
branded dd-wrt) with squashfs-factory.bin
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/17227
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ARIA block cipher is pretty uncommon in TLS, deactivate it for now.
This saves some space and reduces the possible variations and attack
vectors of mbedtls.
ARIA support was deactivated in OpenWrt 23.05 by default.
Link: https://github.com/openwrt/openwrt/pull/17342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the following error by backporting upstream update:
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
Fixes: https://github.com/openwrt/openwrt/issues/17345
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17352
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The boards where renamed, but BUILD_DEVICES was not adapted. This
variable points to the board name. Without this change the u-boot
binaries are not selected in the configuration.
Copy the u-boot binaries under the BUILD_DEVICES name as it is expected
by the image scripts.
Fixes: 33e23e8922 ("build: d1: add SUPPORTED_DEVICES")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No need to pass the option no-warn-rwx-segments. Since v2.12, TF-A
automatically selects it if needed.
A patch is added to revert commit 03a581e2 ("feat(stm32mp1-fdts): remove
RTC clock configuration").
This commit removed RTC clock configuration, as it assumed that it was done
correctly by OPTEE.
But it is not the case. Without this patch the RTC is in a bad state,
consequently the wifi module cannot be initialized.
stm32_rtc 5c004000.rtc: rtc_ck is slow
stm32_rtc 5c004000.rtc: Can't enter in init mode. Prescaler config failed.
stm32_rtc: probe of 5c004000.rtc failed with error -110
sdio mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.st,stm32mp135f-dk.bin failed with error -2
brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since v2.12, TF-A automatically selects the no-warn-rwx-segments option if
needed.
So move this hack to the package Makefiles.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now the tool mkeficapsule is built by default if EFI_LOADER config is set
(which is the case by default for armv7).
This tool needs gnutls, which only exists in the packages feed.
As we don't need mkeficapsule, just disable it.
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tenbay WR3000K is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B.
- SoC: MetiaTek MT7981B
- RAM: Hynex H5TQ2G863GFR 512MiB
- Flash: Winbond W25N01GVZEIG 128MiB
- Wi-Fi: MediaTek MT7976C (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- MediaTek MT7915E: 2.4GHz and 5GHz
- Ethernet: 1x 10/100/1000 Mbps WAN + 3x 10/100/1000 Mbps LAN
- Switch: MediaTek MT7531AE
- UART: J4 (115200 baud)
- LEDs: Power
- Buttons: Reset, WPS
- PWR: 12V/1A DC, 5.5×2.1 connector
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| WAN | wan | Label MAC | Stored MAC in factory + offset 4, label MAC is Stored MAC - 2 |
| LAN | br-lan | Label MAC+1 | |
| 2.4GHz | phy0-ap0 | Label MAC + 2 | |
| 5GHz | phy1-ap0 | Label MAC + 3 | |
- 0x000000000000-0x000000100000 : "BL2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "Factory"
- 0x000000380000-0x000000580000 : "FIP"
- 0x000000580000-0x000003580000 : "ubi"
- 0x000003580000-0x000006580000 : "ubi1"
- 0x000006580000-0x0000065a0000 : "Product"
- 0x0000065a0000-0x000007580000 : "Custom"
- The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi.
- The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt.
- id: 0, kernel
- id: 1, rootfs
- id: 2, rootfs_data
- **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102).
- **Dupont Wires** (male-to-male, 3 wires).
- **PC/Laptop** with a serial communication tool.
- Screwdriver (to open the router case).
1. **OpenWrt Firmware**:
- Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/).
2. **Serial Communication Tool**:
- Windows: PuTTY, Tera Term.
- Linux/Mac: Minicom, screen.
3. (Optional) **TFTP Server**:
- Install a TFTP server like Tftpd64 or tftp-hpa.
---
1. Open the router casing and locate the **TX, RX, and GND** pins.
2. Connect the router pins to the USB-to-TTL adapter as follows:
- **TX (router)** → **RX (adapter)**
- **RX (router)** → **TX (adapter)**
- **GND (router)** → **GND (adapter)**
3. Do **not** connect the VCC pin to avoid damage.
- **Baud rate**: 115200
- **Data bits**: 8
- **Stop bits**: 1
- **Parity**: None
- **Flow control**: None
---
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Select Option 0 by typing 0 and pressing Enter.
5. Input into
```plaintext
MT7981> setenv boot_from ubi
MT7981> saveenv
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
MT7981> printenv
baudrate=115200
boot_from=ubi
...
```
the above indicates system will start from *ubi*.
and then type
```plaintext
MT7981> reset
```
will boot from *ubi*
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Choose Option 3: Upgrade Firmware
Enter Upgrade Mode
Select Option 3 by typing 3 and pressing Enter.
Upgrade Methods
You will be prompted to choose between:
```plaintext
*** Upgrading Firmware ***
Run image after upgrading? (Y/n): y
Available load methods:
0 - TFTP client (Default)
1 - Xmodem
2 - Ymodem
3 - Kermit
4 - S-Record
5 - RAM
Select (enter for default): 0
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.10
Input IP netmask: 255.255.255.0
Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin
```
Type Enter to proceed. The router will erase the old firmware and write the new one.
Signed-off-by: Jianyu Zhuang <xzjianyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
`btusb` fails to start on MT7925 hardware without the appropriate
firmware being loaded first:
```
bluetooth hci0: Direct firmware load for mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin failed with error -2
bluetooth hci0: Falling back to sysfs fallback for: mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin
```
Package firmware for MediaTek MT7925 Bluetooth from `linux-firmware`.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17331
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4b849214b137 ipq8074: add TP-Link EAP620 HD v1 BDF Add board file for TP-Link EAP620 HD v1. Sourced from bdwlan_US.bin in stock firmware 1.1.0 Build 20211028
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix the hexdump applet's formatting with certain format types
by applying the upstream fix for 1.37.0.
Also refresh patches.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17308
[Changed to 002- patch file name prefix]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
access to undeclared variable radio In [anonymous function](), file /usr/share/hostap/hostapd.uc, line 830, byte 45:
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
e00958884416 fw4: do not add physical devices for soft offload
dfbcc1cd127c fw4: skip not existing netdev names in flowtable device list
18fc0ead19fa init: use the reload data trigger to reload firewall on procd data changes
Fixes: https://github.com/openwrt/openwrt/issues/13410
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently if the host system has cmocka installed it will leak the host
path and try to use the host cmocka and build tests.
This will obviously fail, so backport upstream commit allowing disabling
of tests and disable building them.
Fixes: openwrt/packages#25456
Link: https://github.com/openwrt/openwrt/pull/17297
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCA2066 firmware package, ath11k is already supported.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17260
Signed-off-by: Robert Marko <robimarko@gmail.com>
93461ca4c827 unet-cli: only apply defaults on create
3e5766783d5d unet-tool: add support for confirming password
074d3659ca4a unet-cli: confirm password when creating new seed based key
bf3488a3807a unet-cli: add add/set-local-host command
9eb57c528461 unet-cli: add support for setting interface zone
a0a2d80f3459 ubus: add firewall rules for network port/pex_port via procd
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2e206dbe77ec service: add support for triggers on service/instance data changes
735b48728fca service: remove leftover lines from previous commit
32469644a029 service: allow incremental changes to service properties
fd01fb852302 service: fix double free bug when dealing with data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
058a099f5bc5 interface: fix memleak and reload issue for the zone attribute
ea01ed41f321 interface: remove unnecessary NULL checks before free()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
d22d7db581d5 bpf_skb_utils.h: add missing include to fix build against newer kernel headers
bbd3e0eb1419 host: fix peer routes on a node acting as gateway
b17164751fc7 unet-tool: add support for generating keys from salt + seed passphrase
041e05870c20 unet-tool: add support for dumping pubkey from signed file
b58920d420cb unet-tool: add support for extracting network data from signed bin file
f335f5b40b4e unet-cli: add support for generating key from seed
8b1f1d099352 unet-cli: add support for importing networks from signed data
188ba05eadf2 unet-cli: add missing command line help for import
8f15fc306a40 unet-cli: fix add-ssh-host with seed keys
486bc3b86dc2 pex-msg: enable broadcast for global PEX socket
e4a24cdfbc1c unet-cli: fix defaults on create
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes "sh: write error: Invalid argument" for all default!=1 LEDs
as an empty $brightness was used.
Setting up LEDs via luci also now works again.
Fixes cbdfd03e: "base-files: add option to set LED brightness"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/issues/17269
Signed-off-by: John Crispin <john@phrozen.org>
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.
- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
- 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
- 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
- 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector
The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| LAN | br-lan | Label MAC | Default |
| WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN |
| 2.4GHz | phy0-ap0 | Label MAC | |
| 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) |
| Modem | eth1 | Label MAC+2 | |
1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
- Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.
Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```
Power off the router, hold the **WPS button**, and power it back on.
1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.
- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
```bash
cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
```
Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://github.com/openwrt/openwrt/pull/17197
Signed-off-by: John Crispin <john@phrozen.org>
refresh the following patch for ath12k
001-wifi-ath12k-add-11d-scan-offload-support-and-handle-country-code-for-WCN7850.patch
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17246
Signed-off-by: John Crispin <john@phrozen.org>
Ensure that the code doesn't pass macaddr_base with the wrong type (null)
to the supplicant setup/start call.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Name the pidfile of each dropbear instance according to the
corresponding uci section name. This enables a 1:1 mapping between the
definition of the service instance and its process.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/15177
Signed-off-by: John Crispin <john@phrozen.org>
fix default timezone to correct GMT0,
origin value 'UTC' is zonename, not timezone.
Signed-off-by: Jiale Liu <admin@licsber.site>
Link: https://github.com/openwrt/openwrt/pull/15128
Signed-off-by: John Crispin <john@phrozen.org>
Initial support for dynamic reload of RxKHs.
In order to check if RxKHs need reloading.
RxKHs defined in the rxkh_file first has to be parsed and formated,
the same way as hostapd will read from the file and also output,
with the command GET_RXKHS.
Then each list of RxKHs can be hashed and compared.
Ucode implementation of hostapds rkh_derive_key() function.
Hostapd converts hex keys with 128-bits or more when less than 256-bits
to 256-bits, and truncates those that are more than 256-bits.
See: https://w1.fi/cgit/hostap/commit/hostapd/config_file.c?id=245fc96e5f4b1c566b7eaa19180c774307ebed79
Signed-off-by: Sybil127 <sybil127@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With rxkh_file, hostapd will read a list of RxKHs from a text file.
This also makes it possible for hostapd to dynamically reload RxKHs.
RxKHs defined in rxkh_file should be formated as described in hostapd.conf,
with one entry per line.
R0KH/R1KH format:
r0kh=<MAC address> <NAS Identifier> <256-bit key as hex string>
r1kh=<MAC address> <R1KH-ID> <256-bit key as hex string>
Reworked behavior of the uci options r0kh and r1kh.
When rxkh_file is not configured:
Instead of appending the RxKHs to the hostapd bss configuration.
They will be added to a interface specific file with name
/var/run/hostapd-phyX-apX.rxkh.
This file will be used as the rxkh_file in the hostapd bss configuration.
When rxkh_file is configured:
The specified file will be used in the hostapd bss configuration,
and will be the only source for configured RxKHs.
All RxKHs defined with the uci options r0kh or r1kh will be ignored.
Signed-off-by: Sybil127 <sybil127@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit 1cea889c96.
This reverts commit 5fd86d66c1.
The patch is causing build servers to fail. Revert it for now.
Signed-off-by: John Crispin <john@phrozen.org>
This option enables support for monochrome LEDs that are grouped into multicolor
LEDs which is useful in the case where LEDs of different colors are physically
grouped in a single multi-color LED and driven by a controller that doesn't have
multi-color support.
Signed-off-by: Jonathan Brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16397
Signed-off-by: John Crispin <john@phrozen.org>
Some devices use file '/tmp/sysupgrade.tar' during settings restore and
this potentially big file was not being cleaned up from RAM afterwards.
See: do_mount_root() (base-files/files/lib/preinit/80_mount_root)
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15339
Signed-off-by: John Crispin <john@phrozen.org>
dnsmasq passes a limited amount of information via DHCP script arguments. Much
more information is available through environment variables starting with
DNSMASQ_, such as DNSMASQ_INTERFACE. However, when the dhcp-script builds its
JSON environment and passes it to hotplug, all of this information is discarded
since it is not copied to the JSON environment.
Personally, I have a custom-made set of DDNS scripts and rely on environment
variables such as DNSMASQ_INTERFACE in order to determine which DNS zones
to update. So, not being able to access these variables was detrimental to me.
I patched in a quick copy of all DNSMASQ_ variables to the JSON environment
so that they can be used in hotplug scripts. In order to do so I also copied
/usr/bin/env into dnsmasq's chroot jail.
Signed-off-by: Chuck R <github@chuck.cloud>
Link: https://github.com/openwrt/openwrt/pull/16354
Signed-off-by: John Crispin <john@phrozen.org>
Group 'local' declarations and 'json_get_vars', sort alphabetically within groups, and split off more generic parameters.
- delegate and sourcefilter were not declared as local variables
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16734
Signed-off-by: John Crispin <john@phrozen.org>
Group 'local' declarations and 'json_get_vars', sort alphabetically within groups, and split off more generic parameters.
- delegate and sourcefilter were not declared as local variables
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Group 'local' declarations and 'json_get_vars', sort alphabetically within groups, and split off more generic parameters.
- delegate and sourcefilter were not declared as local variables
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Add option to set LED brightness via uci:
config led 'led_blue'
option name 'blue'
option sysfs 'blue:status'
option brightness '1'
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17190
Signed-off-by: John Crispin <john@phrozen.org>
change Support-UDP-Traceroute rule from 'enabled false' to 'enabled 0'
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17133
Signed-off-by: John Crispin <john@phrozen.org>
Regarding SAE support in wifi-station:
Important Note: Unlike PSK wifi-stations, both `mac` and `key` options are required
to make it work. With PSK, hostapd used to perform a brute-force match to find which
PSK entry to use, but with SAE this is infeasible due to SAE's design.
When `mac` is omitted, it will allow any MAC address to use the SAE password if it
didn't have a MAC address assigned to it, but this could only be done once.
The last wildcard entry would be used.
Also, unlike "hostapd: add support for SAE in PPSK option" (commit 913368a),
it is not required to set `sae_pwe` to `0`. This gives it a slight advantage
over using PPSK that goes beyond not needing RADIUS.
Example Configuration:
```
config wifi-vlan
option iface default_radio0
option name 999
option vid 999
option network management
config wifi-station
# Allow user with MAC address 00:11:22:33:44:55 and matching
# key "secretadminpass" to access the management network.
option iface default_radio0
option vid 999
option mac '00:11:22:33:44:55'
option key secretadminpass
config wifi-vlan
option iface default_radio0
option name 100
option vid 100
option network guest
config wifi-station
# With SAE, when 'mac' is omitted it will be the fallback in case no
# other MAC address matches. It won't be possible for a user that
# has a matching MAC to use this network (i.e., 00:11:22:33:44:55
# in this example).
option iface default_radio0
option vid 100
option key guestpass
```
Regarding PSK file creation optimization:
This patch now conditionally runs `hostapd_set_psk_file` depending on `auth_type`.
Previously, `hostapd_set_psk` would always execute `hostapd_set_psk_file`, which
would create a new file if `wifi-station` was in use even if PSK was not enabled.
This change checks the `auth_type` to ensure that it is appropriate to parse the
`wifi-station` entries and create those files.
Furthermore, we now only configure `wpa_psk_file` when it is a supported option
(i.e., psk or psk-sae is used). Previously, we used to configure it when it was
not necessary. While it didn't cause any issues, it would litter `/var/run` with
unnecessary files. This patch fixes that case by configuring it depending on the
`auth_type`.
The new SAE support is aligned with these PSK file changes.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17145
Signed-off-by: John Crispin <john@phrozen.org>
93458ac dns: fix response to TYPE_PTR query
68af311 fix unicast response port and timeout
a2b4979 service: announce all services in single dns answer
4537734 display announced services in ubus call umdns browse
0b50c29 display more srv attributes in output of ubus browse function
Signed-off-by: John Crispin <john@phrozen.org>
e2f05de state: set_stdio: chdir back to / in case of failure
30542c9 inittab: Disable implicit controlling TTY.
Signed-off-by: John Crispin <john@phrozen.org>
libbfd feature is not used when building eBPF program, and it makes bpftool fail to build in a clean environment, since binutils in toolchain have libbfd disabled.
Signed-off-by: Eric Long <i@hack3r.moe>
Link: https://github.com/openwrt/openwrt/pull/17073
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable the busybox feature to save shell command history.
(.apk size increase 0.5 kB)
To prevent flash wear,
* save history only at the exit from a shell session, and
* set /tmp as the default location for the history file. The history
is kept on ramdisk until a reboot, when the history is then lost.
If the user wants to save history onto flash, he can change the location
definition in /etc/profile.d/busybox-history-file.sh
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17179
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
* RGB system led
* USB blue led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part
- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel
Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Co-Authored-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
47b54cf5a4b6 types: introduce `ucv_array_sort_r()` and `ucv_object_sort_r()`
efeb57806552 types, vm: refactor usage of global variables
f9d2faf67de6 vm: reset signals when freeing VM
4e86847d802d lib: utilize `ucv_array_sort_r()` and `ucv_object_sort_r()`
c71444ea301f types: ucv_resource_create(): rename `typename` parameter to `type`
373df7299c79 nl80211: properly support split_wiphy_dump for single phys
9bcd25f54708 lexer: Preserve keyword, regexp flags until processing non-comment tokens
0a7ff4715cb8 main: pretty-print `-p` output by default
4c3d5b469156 struct: Add new buffer API for incremental packing/unpacking
efc4122124cb struct: do not use global variables for caching types
Fixes: https://github.com/jow-/ucode/issues/248
Fixes: https://github.com/jow-/ucode/issues/250
Fixes: https://github.com/efahl/owut/issues/25
Link: https://github.com/openwrt/openwrt/pull/17191
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000 1.5GHz
RAM: NTCC256M16ER-EK 512MiB
Flash: W29N01HZSINA 128MiB
ETH: QCA8075 (3x LAN, 1x WAN)
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Power: DC 12V 1.5A
Button: Reset, Wps
USB: 1x 2.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
Contains following updates:
* ipq8074: add TP-Link_deco-x80-5g BDF
* ipq6018: add BDF for Qihoo 360V6
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
Change the cron log level in init script from 5 to 7
in order to match previous log behavior and to avoid
log spam every minute.
Busybox cron only uses levels 5,7,8, where 5 is debug and
7 and 8 are normal logging. Use 7 as default.
(Fun note: this is needed because upstream corrected an
ancient bug in their own log level handling and now 5 actually
means something.)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a patch to fix non-x86 builds, refresh patches and update/fix the
configuration as described in 98b09ba250 (cited here for future reference).
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.37.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.37.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014fcca)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[rebased with the change download line commit]
[corrected version in the refresh example in commit message]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- fix variable references for ft key
- add r0kh and r1kh if ft_generate_local is not set (logic inversion bug)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The internal hostapd version cannot be built with EAP-pwd support, so
enable it only for the SSL variants.
Fixes: #17163
Fixes: 6365316fab ("hostapd: add ubus support for wired driver")
Link: https://github.com/openwrt/openwrt/pull/17164
Signed-off-by: Robert Marko <robimarko@gmail.com>
3da6c104f0f5 database: use APK_DB_LAYER_ROOT in more places
5437e3abada1 audit: add usr/lib/apk to the list of protected paths under --full
de9baf912245 change default db location to /usr, but detect and use /lib if exists
218fdaa1a1a2 context: close root_fd on free
d33294236cb4 database: add support for only-when-modified trigger paths
36935db0ef3b package: fix memfd_create warnings on Linux kernels < 6.7
1c3fc36051a3 blob: add and use apk_blob_trim_{start,end}
af5f9e3f93b0 pkg: fix v3 package size setting to installeddb
9428e34694c8 version: allow --check and --test to work without database
4b4add5326a8 test: fix unit test registration function to be unique
eac18cb200d4 test: add testlib.sh for user tests
20dae205b006 mkpkg: fix creation of package with hardlinks
7bdecdca6a95 pkg: only allow tags in world and some commands
76de228bcc0b commit: show tags of world constrains
9a1b1cf68420 test: use testlib for solver.sh
99fc2a2a5efc test: remove dependency on GNU tar
6927746b9a10 Revert usrmerge/LFS related changes to apk used paths
5d287a9b06e9 apk-tools-3.0.0_pre5
8d93a79fb895 mkpkg: fix hardlink on big-endian system
Link: https://github.com/openwrt/openwrt/pull/17148
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rename jffs2reset to factoryreset. Convert all scripts to using the new command
line. Print a deprecation notice when jffs2reset is invoked.
49d36ba jffs2reset: rename to factoryreset
b135064 jffs2reset: print deprecation message
Signed-off-by: John Crispin <john@phrozen.org>
Add an ucode based re-implementation of the shell script based wifi code.
The new code is jsonschema driven. The code has been refactored into several
files making it easier to follow.
The new scripts are also way faster than the previous sh implementation.
The new code is currently opt-in via WIFI_SCRIPTS_UCODE and defaults to
EXPERIMENTAL.
Signed-off-by: John Crispin <john@phrozen.org>
Add an ucode based re-implementation of iwinfo. The tool behaves like the old
one with a few minor output differences. It is now possible to add -j to any
command resulting in JSON output.
The new code is currently opt-in via WIFI_SCRIPTS_UCODE and defaults to
EXPERIMENTAL.
Signed-off-by: John Crispin <john@phrozen.org>
b0b5d93 Merge pull request #234 from IdWV/fs
60e7a88 Merge pull request #232 from sebastianertz/lib-digest
1752779 digest: implement compile time option to exclude less common algorithms
c7268a1 ci: include libmd in MacOS CI builds
fcb6f70 lib: introduce digest library
1323a27 Merge pull request #246 from jow-/fix-upvalue-resolve
ed5ce8f types: resolve upvalue values in arrays and objects
a6e0641 vm: resolve upvalues before pushing them onto the stack
ef1baab ci: drop OpenWrt tests for now
63e18ea fs: eliminate the usage of global variables
b1bd7b5 types: add ucv_resource_create() helper
3408edf Merge pull request #244 from nbd168/nl80211
8af77e7 nl80211: add new attributes for multi-radio support
1423ad7 nl80211: cover extended feature and EHT rate info attributes
ee1d6d8 Merge pull request #237 from sebastianertz/math
4b18a9b Merge pull request #213 from jow-/improve-vector-macros
1f022c0 math: removed global variable for thread safety
e5fe6b1 treewide: refactor vector usage code
20307ee utils: improve vector utilities
aa18952 Merge pull request #241 from jow-/socket-local-fanout-decl
79ccd9c socket: provide local definition of `struct fanout_args`
402280d Merge pull request #239 from jow-/safe-insert-during-obj-iteration
07afe96 Merge pull request #240 from jow-/stricter-number-conversion
736d450 types: fix potential use after free on adding keys during iteration
4134e71 vallist: more thoroughly check for trailing garbage after numeric string
9cf53dd Merge pull request #226 from jow-/lexer-improvements
2b2e732 lexer: make api functions public
855854f lexer: emit comment and template statement block tokens
328a50f lexer: improve token position reporting
fa22732 Merge pull request #225 from jow-/compiler-fix-keyword-property-labels-after-spread
6e88c62 Merge pull request #224 from jow-/lib-fs-readline-leak
94d1211 compiler: properly treat property names after spread expressions
67cd123 fs: fix potential memory leak on i/o errors in .read()
Signed-off-by: John Crispin <john@phrozen.org>
Use and alternate ubus object when the config contains "driver=wired". This
commit is in preparation of the ieee8021x-wired daemon.
Signed-off-by: John Crispin <john@phrozen.org>
This allows a radius server to send AVPs for client rate control inside the
accept message. Further add the ratelimits to the sta-authorized ubus
notification.
Signed-off-by: John Crispin <john@phrozen.org>
* add a UCI option to disable all LEDs.
* add an init.d parameter to blink all LEDs
* add on/off parameters to init.d
Signed-off-by: John Crispin <john@phrozen.org>
Avoid harmless error from network script by checking presence of
now-optional wifi support script, most notably confusing users of x86
snapshots.
Fixes: #14964
Signed-off-by: Andris PE <neandris@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14986
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add U-Boot replacement loader for the MERCUSYS MR90X. This is required
to increase available flash space in OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for RTL8812au/RTL8821au USB adapters.
Run-tested: x86/64/rockchip
USB adapters tested: Alfa AWUS036ACS, D-Link DWA-171 A1.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport support for RTL8812AU/RTL8821AU USB adapters
Manually backported patch:
045-v6.13-wifi-rtw88-Enable-the-new-RTL8821AU-RTL8812AU-driver
Patches from 046 to 051 are pending.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
[Move BPAUTO_WANT_DEV_COREDUMP to original patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds firmware support for the RTL8812AU/RTL8821AU USB wireless adapters.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
libapk as a library is used nowhere else and makes no sense to link it
shared. By linking static, we can take advantage of LTO and get the size
reduced further.
Some numbers locally:
Before:
168K staging_dir/target-mips_24kc_musl/root-ath79/usr/bin/apk*
252K staging_dir/target-mips_24kc_musl/root-ath79/usr/lib/libapk.so.2.99.0*
Static:
344K staging_dir/target-mips_24kc_musl/root-ath79/usr/bin/apk*
Static + LTO:
305K staging_dir/target-mips_24kc_musl/root-ath79/usr/bin/apk*
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17109
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.
At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
tools/gmp was using the .tar.xz while package/libs/gmp was using the
.tar.gz archive of the GMP release. Use the .tar.gz for both of them.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It was reported, that a small typo sneaked in, so lets fix it.
Reported-by: @dave14305
Fixes: c19c31f7aa ("base-files: add migration information for APK")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
86da5cbcdb9d system-linux: do not pull ifindex/flags from netlink messages on rtnl events
cd96f61ba63e proto-shell: fix spurious interface teardowns with host deps
a39fe3a8b150 wireless: add support for adding a list of devices for a wifi-iface
d29cf707478c iprule: add ipproto property
768027c5a764 system-linux: restore reading flags from netlink messages
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17074
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently we're going to ship all the apk keys in the keyring, but the
preference is to ship and use single release/branch specific key so lets
use openwrt-snapshots.pem for apk explicitly as well.
Fixes: 2cea050024 ("openwrt-keyring: add apk public key for signing of package indexes")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16852
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 37784c48e9 as the
preference is to have single explicit key for each release/branch.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16852
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.
Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
/tmp folder of the router using scp.
2. Make mtd partitions backups:
http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
contents
3. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```
4. Write FIP and preloader:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/ubootmod-preloader.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```
5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
with IP 192.168.1.254.
6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.
7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
router using scp.
8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```
Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
button.
3. Use OpenWrt initramfs system for recovery.
BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
router using scp.
2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```
3. Restore stock U-Boot and reboot:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/BL2.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/FIP.bin FIP
reboot
```
4. Open U-Boot web recovery, upload stock firmware image and start
upgrade.
Link: http://192.168.1.1
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the dependency on the kmod-media-controller from depends to
select.
Fixes: 1095925246 ("kernel: add kmod-media-controller dependency for kmod-usb-audio")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that we have some kind of a symbol name conflict which causes
CONFIG_SECCOMP to always be read as y.
Unfortunatelly, I could not figure out what is causing this, but simply
renaming SECCOMP to USE_SECCOMP seems to properly work and leaves the
symbol unset unless arch dependencies are satisfied.
This fixes qoriq and others that dont support seccomp from failing due
to procd-seccomp package being selected to get included but it cannot be
built for them:
ERROR: unable to select packages:
procd-seccomp (no such package):
required by: base-files-1637~52b6c92479[procd-seccomp]
Fixes: 4c65359af4 ("build: fix including busybox, procd and apk/opkg in imagebuilder")
Link: https://github.com/openwrt/openwrt/pull/17048
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).
The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.
Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.
This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh
The idea and the implementation were thankfully taken from PR #16410.
This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This package contains nvram files for Murata's Wi-Fi/Bluetooth modules.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This package contains firmwares provided by Murata.
See https://community.murata.com/.
Murata firmwares are used by wifi chip on stm32 boards.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All stm32 devices use BCM43430 Wi-Fi interface in SDIO mode.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add ATF for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add U-Boot for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add OP-TEE for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixup capabilities parsing in iw output.
In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.
The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```
With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).
Link: https://github.com/openwrt/openwrt/pull/17043
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add anchor to name search so that we don't inadvertently filter out
packages containing, say, "kernel-" as part of their name.
Fixes: openwrt/packages#25372
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17032
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allows us to drop the description backport.
Changes:
e3464d0 db: make repository description an atom instead of allocation
417a93c pkg: truncate apkv3 description to 256 bytes
d26b65d db, audit: remove support for files without embedded checksum
64ff8c7 db: allow files starting with a dot in the root directory of apk3 packages
89e4bf1 db, fs: do not extract devices in --usermode
4050f9e db: fix hardlink handling: root directory and v3 checksums
ade0be3 db, extract: handle file/directory extraction errors more consistently
a4837ae package: don't call make_device_tree when APK_NO_CHROOT is set
1e04115 package: respect libexecdir instead of hard-coding /usr/libexec
76970a9 package: move the location of executable package scripts
19b1df7 blob: refactor apk_blob_for_each_segment into apk_blob_foreach_word
e38d5b5 test: add missing alpine tests makefile
fcd4def test: move vertest to cmocka based unit testing infrastructure
8a13ed9 test: fix solver.sh for parallel use
5add6fc (tag: v3.0.0_pre4) apk-tools-3.0.0_pre4
5dd91e3 db: consider --force-no-chroot when determining /dev/fd availability
d86afde db: print message when a file is written to .apk-new
a5aeb3d test: unify makefile and meson tests
a236fdd pkg: use memfd_create only if target root has dev/fd working
563d364 tests: minor updates to root tests
08b4d21 tests: move solver test data to separate directory
c259642 tests: rework solver tests to not require apk-test binary
d2aaf13 commit: sort matched dependencies on error analysis
98d7196 db: fix permissions of arch file
b231eac db: simplify add_repos_from_file
2a3dbfc db: add and use apk_db_parse_file helper to parse files line by line
c1a3e69 db: validate package arch against compatible arches
Link: https://github.com/openwrt/openwrt/pull/17015
Signed-off-by: Robert Marko <robimarko@gmail.com>
b6ae9ffaeb0e odhcp6c: allow to request specific ipv6 prefix
Signed-off-by: He Ping <pinghejk@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17013
Signed-off-by: Petr Štetiar <ynezz@true.cz> [hash, commit]
Now that omnia-eeprom is marked nonshared building the cortex-a9 mvebu
subtarget will fail with:
ERROR: unable to select packages:
omnia-eeprom (no such package):
required by: world[omnia-eeprom]
This is because omnia-eeprom depends on TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia
which will not be satisfied in buildbots since CONFIG_TARGET_ALL_PROFILES
and CONFIG_TARGET_PER_DEVICE_ROOTFS are set in which case
CONFIG_TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia is not set.
So, lets simply depend on the mvebu/cortex-a9 subtarget.
Fixes: 371e7bef40 ("omnia-eeprom: Mark it nonshared")
Link: https://github.com/openwrt/openwrt/pull/17007
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ubihealthd to the nand-utils package, auto-create UCI config for
each UBI device and launch the daemon on boot.
The default time interval between scrubbing a random PED is 120 seconds
which means that a fully used 128 MiB flash chip gets scrubbed in about
a day and a half. The interval can be adjusted in UCI using the
'interval' option.
Suggested-by: Rodrigo Balerdi <lanchon@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/16973
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove the remaining special handling of procd-ujail in a same way as
the rest of the packages was handled in the commit 4c65359af4 ("build:
fix including busybox, procd and apk/opkg in imagebuilder").
Fixes: 44598c233d ("build: remove broken dependency of metadata on toplevel .config variables")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16986
Signed-off-by: Robert Marko <robimarko@gmail.com>
The config_get_bool also works with on/off, yes/no, true/false.
Add 'main' section name. This will make it easier to change settings from uci.
Add a link to documentation.
Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15579
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This tool was build in the phase 2 build, there the
TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia dependecy was probably
not meat. Mark it as non shared to build it together with the target
where this option is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16975
Signed-off-by: Robert Marko <robimarko@gmail.com>
This tool was build in the phase 2 build, there the TARGET dependencies
are probably not meat. Mark it as non shared to build it together with
the targets where this option is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16975
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable drm-i915 module for target x86/geode.
Fixes: 77cfe8f ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16977
Signed-off-by: Robert Marko <robimarko@gmail.com>
On aarch64 musl gcc 14.x compiler, trying compiling elfutils 0.192 with
lto option enabled will cause null-dereference error.
Example error message:
...
elf_compress.c: In function 'elf_compress':
elf_compress.c:675:26: error: potential null pointer dereference [-Werror=null-dereference]
675 | shdr->sh_flags |= SHF_COMPRESSED;
| ^
elf_compress_gnu.c: In function 'elf_compress_gnu':
elf_compress_gnu.c:127:25: error: potential null pointer dereference [-Werror=null-dereference]
127 | shdr->sh_size = new_size;
| ^ ^
...
This is a false postive warning but will abort compilation if gcc has
`-Werror` flag. This commit add a patch for this, see the bugzilla
report below.
This commit backports a series of patches to fix some errors.
Add patch:
- 007-add-libeu-symbols-to-libelf.patch
- 008-fix-autoconf-ENABLE_IMA_VERIFICATION.patch
- 009-fix-null-dereference-with-lto.patch
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=32311
Signed-off-by: Ryan Keane <the.ra2.ifv@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16886
Signed-off-by: Robert Marko <robimarko@gmail.com>
Analog to how we handle custom feeds in opkg, add a customfeeds.list for
custom package feeds and mark it as a configuration file.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16940
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Analog to how we handle distfeeds with opkg, have the base feeds defined
in a file in repositories.d instead of the base /etc/apk/repositories.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16940
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, libreadline only installs
```
/usr/lib/libhistory.so.8 -> libhistory.so.8.2
/usr/lib/libhistory.so.8.2
/usr/lib/libreadline.so.8 -> libreadline.so.8.2
/usr/lib/libreadline.so.8.2
```
But there is no `libreadline.so` or `libhistory.so` available.
So this happens:
```
root@OpenWRT:~# cat a.c
int main() {
}
root@OpenWRT:~# gcc a.c -lreadline
/usr/bin/ld: cannot find -lreadline: No such file or directory
collect2: error: ld returned 1 exit status
```
Unless, of course, one uses `-l:libreadline.so.8`... But that
doesn't help with binaries that try to dynamically open
`libreadline.so`. I have one of those here (the STklos Scheme
compiler -- I didn't make a PR for it because it's far from
being ready, but one issue is that it does use dlopen to use
readline...)
With the symlink, it works:
```
root@OpenWRT:~# ln -s /usr/lib/libreadline.so.8 /usr/lib/libreadline.so
root@OpenWRT:~#
root@OpenWRT:~# gcc a.c -lreadline
root@OpenWRT:~#
```
Another example: when trying to package rlwrap, the build failed
complaining it could not find readline (using `-lreadline`).
It would then be necessary to change rlwrap's `configure.ac`
(and also in all packages that use readline), but it seems
simpler to add the symlinks...
This PR changes the Makefile so it will include the links.
Signed-off-by: Jeronimo Pellegrini <j_p@aleph0.info>
Link: https://github.com/openwrt/openwrt/pull/16445
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The ppp package can support all features since Linux 4.7.0 kernel.
Therefore, most kernel version checks can pass unconditionally on
OpenWrt v18.06 and later version. This patch can reduce the size
of ppp package by approximately 2.5 KB.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16695
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These permissions are not needed. Systemd also mounts these file systems
without these permissions on other Linux distributions.
Dropping these permissions should make the system more secure.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16960
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Create the folder /run and /run/lock using symlinks. Other Linux
distributions also have these folders and some applications might already
depend on them. Just create symlinks pointing to the older folder.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16961
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Do not add the file /run/apk/db.lock to the root file system. The /run
folder should be on a tmpfs.
At runtime we should make /run point to a tmpfs. At build time we should
just remove the folder.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16961
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
Change the package name from intel-igpu-firmware-* to i915-firmware-*,
the prefix "intel-igpu" is misleading, i915 firmware is not only for
iGPU but also for dGPU now.
Remove the redundant "intel" as i915 is already well known.
More accurate file classification to handle following files correctly:
adlp_dmc.bin
mtl_huc.bin
mtl_huc_gsc.bin
mtl_gsc_1.bin
The pattern in regex is "([[:alnum:]]+)_([[:alnum:]]+)(_[\w-.]+)?\.bin",
where $1 is the platform, $2 is the firmware type (dmc, guc, huc, etc.),
and the optional $3 which is revision or other suffix.
Glob first to narrow down the target file set, and then split with "_"
to extract the firmware type (remove the ".bin" in case there is no $3)
Add package "i915-firmware" as a meta package to install all the i915
firmwares, it is a balance between simplicity and optimization.
* Installing all the available firmwares as a whole, can support all the
platforms, not only the current one but also the future ones. The
price to pay is the increased size.
* If we want to minimize the storage, we can customize to install the
necessary ones only, even for the target platform only (e.g. ADL) and
skip the others. The price to pay is the time to tune.
What I am going to do is:
* Let drm-i915 driver depend on i915-firmware-dmc, which is small and
can cover most of the old platforms
* Let the user select i915-firmware to install all the i915 firmwares as
a whole to cover the latest or future platforms
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new utility, `omnia-eeprom`, which can be used to print / set
EEPROM fields on Turris Omnia.
One example when this utility might be useful is if the board
experiences random crashes due to newer versions of the DDR training
algorithm in newer U-Boot. The user can change the DDR speed from 1600K
to 1333H to solve these issues, with
```
omnia-eeprom set ddr_speed 1333H
```
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/16264
Signed-off-by: Robert Marko <robimarko@gmail.com>
In preparation for APK version bump, use /dev/null instead of /dev/zero
for --repositories-file to mute an error in recent APK files.
New APK version use modern istream logic that are more sensible to the
kind of file passed and /dev/null is required to correctly handle an
empty repository file.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently its not possible to generate apk package.adb package index if
the package has longer description field, which leads to following
failure:
(2352/2353) Installing zoneinfo-all (2024b-r1)
(2353/2353) Installing zstd (1.5.6-r1)
ERROR: System state may be inconsistent: failed to write database: No buffer space available
1 error; 2704 MiB in 2353 packages
The code to read/write installeddb does not really handle long
description well. Until the database is converted to apkv3 format,
truncate the apkv3 descriptions to allow existing code to work.
APKv3 index and packages still contain the original long description
unmodified, so no package rebuild will be needed.
Fixing the issue by backporting the single upstream fix as its not
possible to to upstep apk to the latest Git HEAD due to some
regressions, see commit 692052cdc0e7 ("Revert "apk: update to Git
417a93ceae540444fdbd3f76d1dadf0e15621fdc (2024-11-13)"") for more
details.
Fixes: #16929
References: https://gitlab.alpinelinux.org/alpine/apk-tools/-/issues/11038
Upstream-Status: Backport [417a93ceae]
Link: https://github.com/openwrt/openwrt/pull/16951
Signed-off-by: Petr Štetiar <ynezz@true.cz>
7330fa5 initd: mount /sys and /proc with MS_RELATIME
Fixes mounting /proc in unpriviledged user namespace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
8dfead68c202 wifi: mt76: mt7915: hold dev->mutex while interacting with the thermal state
d508a6eb935d wifi: mt76: mt7996: use mac80211 .sta_state op
57019e663f57 wifi: mt76: add code for emulating hardware scanning
dc4c2bdf7c56 wifi: mt76: add support for allocating a phy without hw
8cd0263f92e1 wifi: mt76: rename struct mt76_vif to mt76_vif_link
99df84d62883 wifi: mt76: add vif link specific data structure
dcc6f158d759 wifi: mt76: mt7996: split link specific data from struct mt7996_vif
d388deab9e73 wifi: mt76: initialize more wcid fields mt76_wcid_init
d026be405c54 wifi: mt76: add chanctx functions for multi-channel phy support
0b05795ca81c wifi: mt76: remove dev->wcid_phy_mask
0b526090de95 wifi: mt76: add multi-radio support to a few core hw ops
aeedee5c0a2c wifi: mt76: add multi-radio support to tx scheduling
fc0ff17b53ff wifi: mt76: add multi-radio support to scanning code
f19cbcf83400 wifi: mt76: add multi-radio remain_on_channel functions
42429ae0eaf6 wifi: mt76: mt7996: use emulated hardware scan support
f9d593d4a6b4 wifi: mt76: mt7996: pass wcid to mt7996_mcu_sta_hdr_trans_tlv
807090b28661 wifi: mt76: mt7996: prepare mt7996_mcu_add_dev/bss_info for MLO support
252baa7bf477 wifi: mt76: mt7996: prepare mt7996_mcu_add_beacon for MLO support
9ee990050305 wifi: mt76: mt7996: prepare mt7996_mcu_set_tx for MLO support
bf12cc404334 wifi: mt76: mt7996: prepare mt7996_mcu_set_timing for MLO support
60bf2bef95dc wifi: mt76: connac: prepare mt76_connac_mcu_sta_basic_tlv for MLO support
1289737e12a8 wifi: mt76: mt7996: prepare mt7996_mcu_update_bss_color for MLO support
7c00df0e7e57 wifi: mt76: connac: rework connac helpers
484e3f289a40 wifi: mt76: mt7996: move all debugfs files to the primary phy
d258f4e3e1ca wifi: mt76: mt7996: switch to single multi-radio wiphy
c246fa545119 wifi: mt76: mt7996: fix monitor mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Explicitly enable help so that the build will fail when an appropriate
lua binary isn't found instead of silently disabling the feature.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Most apk meson args are shared between host and target builds, so lets
have a common variable for them.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Commit b2a84c86e3 ("apk: host: make the help available") enabled the
host build for lua (5.1) as a dependency, but apk defaults to lua 5.3.
This caused it to ignore our lua, and only build the help if the host
system had lua 5.3 installed.
Fix this by explicitly setting the lua version to ours.
Fixes: b2a84c86e3 ("apk: host: make the help available")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This reverts commit c6a3a11c07 as it was
reported, that it causes issues:
ERROR: failed to read repositories: /dev/zero: No buffer space available
ERROR: unable to select packages:
ca-bundle-20240203-r1:
error: uninstallable
arch: all
satisfies: world[ca-bundle]
Reported-by: xiao bo <peterwillcn@gmail.com>
References: c6a3a11c07 (commitcomment-149072959)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
Advantages over stock bootloader:
1. supports serving the external GPIO WDT, allowing for easier work in U-Boot
shell
2. supports cool features like netconsole, easy recovery, scripting and so on
3. allows using FIT image and image integrity validation
and ultimately gives you much more flexibility to implement your tweaks.
Known issues
------------
To make it easier to operate the device, console I/O multiplexing support has
been enabled in U-Boot configuration. Setting I/O related U-Boot environment
variables to something like "serial,nc" will have the desired effect. Still,
setting these variables to such a value in the persistent environment will
lead to a crash and make it impossible to boot the system or recover it. I
decided to leave it on anyway since I think it can be very practical in
development.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
c1a3e69f24e2 db: validate package arch against compatible arches
2a3dbfc9db58 db: add and use apk_db_parse_file helper to parse files line by line
b231eacd8121 db: simplify add_repos_from_file
98d7196a48d4 db: fix permissions of arch file
d2aaf13ee488 commit: sort matched dependencies on error analysis
c259642c006d tests: rework solver tests to not require apk-test binary
08b4d21f922e tests: move solver test data to separate directory
563d36481166 tests: minor updates to root tests
a236fdd39040 pkg: use memfd_create only if target root has dev/fd working
a5aeb3db113f test: unify makefile and meson tests
d86afdef88b0 db: print message when a file is written to .apk-new
5dd91e3c387d db: consider --force-no-chroot when determining /dev/fd availability
5add6fce22d4 apk-tools-3.0.0_pre4
8a13ed96d1d5 test: fix solver.sh for parallel use
fcd4defc18e6 test: move vertest to cmocka based unit testing infrastructure
e38d5b5a9d04 test: add missing alpine tests makefile
19b1df79ebca blob: refactor apk_blob_for_each_segment into apk_blob_foreach_word
76970a938dd7 package: move the location of executable package scripts
1e0411568dad package: respect libexecdir instead of hard-coding /usr/libexec
a4837ae8ffe2 package: don't call make_device_tree when APK_NO_CHROOT is set
ade0be3449e4 db, extract: handle file/directory extraction errors more consistently
4050f9e69d2e db: fix hardlink handling: root directory and v3 checksums
89e4bf1db040 db, fs: do not extract devices in --usermode
64ff8c72d9fb db: allow files starting with a dot in the root directory of apk3 packages
d26b65d30f55 db, audit: remove support for files without embedded checksum
417a93ceae54 pkg: truncate apkv3 description to 256 bytes
Fixes: #16929
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since the image builder pulls package lists from metadata directly,
add procd and busybox as depdendencies to base-files.
As for the package manager itself, since it can be disabled it needs
to be added directly in the image builder makefile
Fixes: 44598c233d ("build: remove broken dependency of metadata on toplevel .config variables")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Duplicate the old opkg index.json using the new apk database.
Needed to get the ASU server working on new snapshots.
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16931
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Change the version schema of perf to be compatible with APK as
described in this commit: e8725a932e.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16930
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Most links and info on the org page are broken or defunct, and all new
versions are available on the github based repo anyway.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
For the last ten years, nobody has noticed that this driver doesn't
actually say what it is for. ;)
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Needed to fix compilation with GCC14.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16912
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of relying on .config symbols for metadata, alter the DEFAULT
variable of affected packages. Fixes enabling opkg vs apk among others.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Refactor version of spidev_test for APK.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16917
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove backtick from gdb description text, as that seems to
be recognized as a shell action by compilation with apk,
causing error.
Example from test buildbot:
rstrip.sh: /builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/gdb-15.2/ipkg-aarch64_generic/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
bash: -c: line 2: syntax error: unexpected end of file
make[3]: *** [Makefile:123: /builder/shared-workdir/build/sdk/bin/packages/aarch64_generic/base/gdb-15.2-r1.apk] Error 2
Local compilation:
rstrip.sh: /OpenWrt/aarch64/build_dir/target-aarch64_cortex-a53_musl/gdb-15.2/ipkg-aarch64_cortex-a53/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
make[2]: *** [Makefile:123: /OpenWrt/aarch64/bin/packages/aarch64_cortex-a53/base/gdb-15.2-r1.apk] Error 2
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16908
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adjust wolfssl version for apk by removing the "-stable"
from the OpenWrt version, although it is still needed for
upstream download archive name.
Define PKG_BUILD_DIR accordingly.
Utilize new short version to simplify ABI_VERSION calculation.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16906
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
/sbin/pkg_check uses opkg and is not even packaged when using the
default opkg configuration. remove it when using apk too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These two were getting rather long.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16849
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We need to exclude packages from the APK index which must not be
upgraded. To do so, the packages `libc`, `kernel` and `base-files` are
excluded to APK never suggestes them as upgradable.
The previous logic would however match packages like `libcomerr0`,
causing build failures. Make the copying and excluding logic more
precise by adding a single dash.
Signed-off-by: Paul Spooren <mail@aparcar.org>
