Restore CONFIG_PAGE_BLOCK_MAX_ORDER=10 in ramips 6.18 config fragments
to fix build failures where PAGE_BLOCK_MAX_ORDER was undefined.
Support for Linux 6.18 on ramips was added after this OpenWrt change:
ac0cb87a45.
Before that integration, the kernel option CONFIG_PAGE_BLOCK_MAX_ORDER=10
was provided in target/linux/generic/config-6.18 and applied broadly.
After the ramips 6.18 integration the generic fragment no longer supplied
this option for ramips targets, which caused some backported code paths
and drivers to assume PAGE_BLOCK_MAX_ORDER was defined and led
to compilation failures.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22831
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some Banana Pi BPI-R4 BE14 WiFi modules are shipped with zeroed
tx_power fields in EEPROM (2G/5G/6G). This leads to low transmit power
on affected bands.
This overlay provides known-good EEPROM data (including correct tx_power
values for 2G/5G/6G bands) dumped from a working BE14 module.
To enable BE14 overlay, add into u-boot bootconf_extra
parameter: 'mt7988a-bananapi-bpi-r4-wifi-be14'.
You can use example script:
overlay="mt7988a-bananapi-bpi-r4-wifi-be14"
current="$(fw_printenv -n bootconf_extra 2>/dev/null)"
if [ -n "${current}" ]; then
fw_setenv bootconf_extra "${current}#${overlay}"
else
fw_setenv bootconf_extra "${overlay}"
fi
Earlier proposal proposed in [1] was fallback to default values if
invalid EEPROM content is detected.
[1] https://github.com/openwrt/openwrt/pull/19503/
Fixes: https://github.com/openwrt/openwrt/issues/17489
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
The correct label mac is needed in a downstream project.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Link: https://github.com/openwrt/openwrt/pull/22801
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is only one check left for that attribute in rtldsa_port_mdb_add().
Split the consumer into device specific implementations and remove the
attribute from the private structure.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22794
Signed-off-by: Robert Marko <robimarko@gmail.com>
The soc_info structure should only be used in the mach setup
functions. Drop its usage in the dsa qos functions. Instead
derive the data from the das private structure.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22794
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are two issues with the current setter.
- It is only called for RTL839x
- It unconditionally overwrites the register and not only
the needed bits.
Fix that by renaming it to the right prefix and using a
register write based on mask.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22794
Signed-off-by: Robert Marko <robimarko@gmail.com>
Split the existing generic priority setters with family
checks into two dedicated paths.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22794
Signed-off-by: Robert Marko <robimarko@gmail.com>
For a long time the dsa driver has been providing a builtin mdio bus
via dsa default attribute user_mii_bus. This simply uses read/write
commands from the standard realtek otto bus (aka parent). The reason
has always been unclear.
Looking around the kernel 6.18 codebase there is only one case where
this is really needed. The only consumer is dsa_user_phy_setup().
ret = phylink_of_phy_connect(dp->pl, port_dn, phy_flags);
if (ret == -ENODEV && ds->user_mii_bus) {
/* We could not connect to a designated PHY or SFP, so try to
* use the switch internal MDIO bus instead
*/
ret = dsa_user_phy_connect(user_dev, dp->index, phy_flags);
}
Luckily the phylink_of_phy_connect() works fine and the internal bus
access is not needed at all. No need to keep the bus alive. Drop it.
While we are here fix the error handling issue of this code
if (!of_device_is_available(dn))
ret = -ENODEV;
Returncode was set to error but never handed back to the caller.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using awk and cut to simulate -n is pointless.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22806
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable CONFIG_SERIAL_8250_MID in the generic x86 configuration.
This enables hardware serial console access on Intel Atom C3000
(Denverton) platforms, which rely on the High-Speed UART driver.
It also benefits other Intel MID platforms across the x86
architecture.
Signed-off-by: Cristian Sloberg <crilleslo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22739
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch enables for the configuration of the sync_time parameter.
The value of the sync_time needs to be specified in nanoseconds.
The default value is 200us (200 000 ns).
This is especially helpful to get feedback from users about suitable
values. Once a solid solution is found this patch can be removed.
Signed-off-by: Jonas Köppeler <j.koeppeler@tu-berlin.de>
Link: https://github.com/openwrt/openwrt/pull/22380
[Add patch to kernel 6.18 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Huasifei WH3000 Pro NAND version.
There is an eMMC already supported in OpenWrt. The only difference is NAND chip.
This commit adds common .dtsi and separate .dts
for eMMC and nand versions.
**Huasifei WH3000 Pro NAND**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: 256mb Winbond SPI NAND
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
M.2 (WWAN) slot
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-nand-squashfs-sysupgrade.bin
```
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ramips now supports 6.18 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MODULE_DEVICE_TABLE macro was using an incorrect parameter 'match'
instead of the actual device table name 'mt7621_nfc_id_table'.
This fixes the reference to use the correct symbol name, ensuring
proper device table registration for module autoloading.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix fe_clean_rx to handle the changed frag_cache layout on newer kernels.
For kernels >= 6.13 the fragment cache needs to be converted from its
encoded_page value instead of using the old va field. Add an ifdef
to use frag_cache.encoded_page & PAGE_MASK and virt_to_page for those
kernels, keep the old path for older kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refreshed patches for ramips/patches-6.18 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace previous bgpio_init usage with a full gpio_chip registration so the driver
integrates cleanly with the kernel GPIO core.
Add drivers/gpio/gpio-ralink.c implementing a gpio_chip with:
- get/set, direction_input/direction_output, get_direction
- get_multiple/set_multiple to support efficient multi-bit ops
- DT handling for determining ngpios (reads "ngpios" or falls back to gpio-ranges)
- MAX_NGPIOS cap and safe defaults
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update patch 831-03-mmc-mtk-sd-use-default-PATCH_BIT1-2-values-for-mt762.patch
to a newer version compatible with kernel 6.18.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove symbols no longer present in version 6.18,
add new 6.18 kernel symbols.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21418
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Realtek mdio bus operations are based on the port number. As
of now the driver exposes a single bus with a 1:1 mapping between
phy and port. This will change in the future when the driver
exposes multiple busses. This will need a mapping - e.g.
- bus 0, phy 23 -> read/write port 23
- bus 1, phy 0 -> read/write port 24
Provide a rtmdio_phy_to_port() indirection function that will
lookup the port number based on a bus and a phy. For now it
will only run some basic sanity checks and return the given
input address (because of 1:1 mapping).
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22731
Signed-off-by: Robert Marko <robimarko@gmail.com>
When the mdio driver gets enhanced for multiple busses it must
snchronize reads/writes to the single controller. Add a lock
to the control structure and guard the critical operations.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22731
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make use of regmap in all device specific set_rx_mode() functions.
Adapt the constant prefixes to the rest of the driver. While we
are here:
- align the RTL931x function name with the other targets
- replace constants with GENMASK()
- use new lowercase style for hexadecimal values
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22757
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ethernet driver currently uses the legacy sw() macros. Add a
regmap to the driver that is derived from the parent mfd (like in
the mdio drivers). As a first consumer make use of that in the IRQ
functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22757
Signed-off-by: Robert Marko <robimarko@gmail.com>
This symbol is selected by CONFIG_BPF, which was already enabled
on generic config-6.18.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is selected by CONFIG_BPF, which was already enabled
on generic config-6.12.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol depends on the specific CPU type, so we should not
set it globally.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is selected by CONFIG_BUILTIN_DTB. However, we didn't
enable it in generic config-6.18.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the Wavlink "Halo Base Pro".
SOC: MT7621DAT
RAM: 128MiB
Flash: 16MiB NOR
WiFi: MT7603EN + MT7613BEN
Buttons:
- The touch sensor was originally for WPS, but this has been moved to the
pair button which is no longer used to prevent accidental touches
LEDs:
- On original firmware, the status LEDs light up as follows:
- Purple = booting, Blue = working, Red = error
Partitions:
- factory contains unique WiFi EEPROM and default MAC addresses
- vendor partition has an unknown purpose
Stock MAC address allocation:
- LAN1: xx:xx:xx:xx:xx:80
- LAN2/WAN: xx:xx:xx:xx:xx:81
- WiFi 2.4G: xx:xx:xx:xx:xx:82
- WiFi 5G: xx:xx:xx:xx:xx:83
LAN Ports:
- lan1 is the normal white LAN port
- lan2 is labelled "LAN/Backhaul", which can either be LAN or WAN.
- Since this device is intended to be part of a mesh, this will usually
be a LAN port, hence why it's assigned to lan2 here
Notes:
- I've chosen "Halo Base Pro" as the device model, despite the website URL
showing WL-WN535M3, as the label only states "Halo Base Pro".
- Only the 5GHz WiFi address is labelled on the device
Signed-off-by: William Latter <williamlatter77@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22400
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compared to the "mediatek,mt8173-xhci", this is a more generic and
reasonable compatible string. On the driver side, they are identical.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The USB t-phy driver includes some magic register init values. This
should be beneficial for the USB stability and performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MT7621 USB phys are compatible with the MediaTek T-PHY controller.
The vendor SDK also enabled this driver for MT7621.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22094
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove unit name leading 0s to fix the following dtc warnings:
danube_arcadyan_arv752dpw22.dts:263.11-273.4: Warning (pci_device_reg): /fpi@10000000/pci@e105400/usb@0f,0: PCI unit address format error, expected "f,0"
danube_arcadyan_arv752dpw22.dts:275.11-285.4: Warning (pci_device_reg): /fpi@10000000/pci@e105400/usb@0f,2: PCI unit address format error, expected "f,2"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18843
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The dtc will treat "spi" node as an SPI controller. This resulted
in lots of false warning reports. Workaround it by renaming the
pinctrl node name to "spi-pins". This patch fixes the following
dtc warnings:
vr9.dtsi:326.18-336.6: Warning (spi_bus_bridge): /fpi@10000000/pinmux@e100b10/spi: incorrect #address-cells for SPI bus
vr9.dtsi:326.18-336.6: Warning (spi_bus_bridge): /fpi@10000000/pinmux@e100b10/spi: incorrect #size-cells for SPI bus
ar9.dtsi:286.18-296.6: Warning (spi_bus_bridge): /fpi@10000000/pinmux@e100b10/spi: incorrect #address-cells for SPI bus
ar9.dtsi:286.18-296.6: Warning (spi_bus_bridge): /fpi@10000000/pinmux@e100b10/spi: incorrect #size-cells for SPI bus
amazonse.dtsi:166.18-176.6: Warning (spi_bus_bridge): /fpi@10000000/pinmux@e100b10/spi: incorrect #address-cells for SPI bus
amazonse.dtsi:166.18-176.6: Warning (spi_bus_bridge): /fpi@10000000/pinmux@e100b10/spi: incorrect #size-cells for SPI bus
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18843
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL8231 LED driver is using the .brightness_set op, which according
to the documentation should not sleep. Since the RTL8231 is controlled
via an MDIO bus, this is not the case.
When using a non-offloaded LED driver such as netdev, this may currently
trigger kernel warnings:
WARNING: CPU: 0 PID: 14 at kernel/time/timer.c:1754 call_timer_fn.isra.0+0x84/0x8c
timer: led_timer_function+0x0/0x1d8 preempt leak: 00000100 -> 00000000
Switch to the .brightness_set_blocking op to indicate the operation
might sleep.
Fixes: 6ef6014887 ("realtek: Add pinctrl support for RTL8231")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This reverts commit a2fa1db797.
These patches stop secondary CPUs before restart and wait for them
to go offline, fixing the mt7621 reboot deadlock without needing to
disable CONFIG_LIST_HARDENED.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/22724
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
rteth_930x_decode_tag() and rteth_931x_decode_tag() are basically
the same. The only difference is the port bitmask. Luckily on the
RTL930x devices the unused fifth bit is always zero and the mask
can be aligned with RTL931x. Take over the RTL931x reason debugging
for both targets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22717
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new PHY_C22() macro for this RTL9301 device.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22721
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the SerDes mode to OFF early in the setup process to have a clear
starting point. This was part of the media handling before as a leftover
from the SDK code import. In the SDK, this function didn't only care
about applying some media settings but was also some kind of mode
setting for fiber modes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22786
Signed-off-by: Robert Marko <robimarko@gmail.com>
Right now we operate with distinct media types for fiber using different
speeds. This is more of a leftover from the SDK then it really makes
sense design-wise. The set_media function from the SDK did a lot more
than just setting some media-specific parameters. As part of
deconstructing this, also reduce the fiber types to a single media type
and handle the speed-agnostic parts based on the hw_mode for now.
This also drops the check for 100M speed around a block of writes. This
check has it's origin in SDK code where a switch statement just didn't
handle this case. However, the rest of the SDK doesn't handle this case
either. While the explicit 100M support isn't verified yet, there's no
need to keep that check.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22786
Signed-off-by: Robert Marko <robimarko@gmail.com>
So far we had separate media types for different DAC cable lengths,
equal to how the SDK defines them. However, this seems overengineered.
The types '_50CM' and '_100CM' are always treated equally, same for
'_300CM' and '_500CM'. Not only in the RTL931x code, but also the
RTL930x code usually just makes a distinction between short and long.
Thus, make that a bit cleaner by reducing the DAC type set to '_SHORT'
and '_LONG' with DAC cables < 3m being considered short and those with
>= 3m being considered as long.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22786
Signed-off-by: Robert Marko <robimarko@gmail.com>
The term 'port media' was chosen due to how the code taken from the SDK
was organized. However, the SDK does a pretty good job at intermixing a
lot of things which cause confusion in the end. This also applies to the
media settings. To be correct, we do not really have port awareness in
the PCS driver (and probably shouldn't have) so we do not really deal
with a port's media. Instead, we set settings depending on what is
attached to the SerDes itself.
To fix this confusion, rename the enum, its fields and all usage from
'port_media' to 'sds_media'.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22786
Signed-off-by: Robert Marko <robimarko@gmail.com>
