A SerDes can host multiple PCS links: QSGMII binds four ports to one
SerDes, USXGMII variants up to eight. Today pcs-handle references the
SerDes as a whole, with no way to express which link inside the SerDes
a port wants. The driver gets away with this because it carries its own
port->link bookkeeping and the link slot is implicit in DSA's port
iteration order -- functional, but the wiring information lives nowhere
in DT.
The upcoming fwnode_pcs migration moves PCS lookup to the generic
fwnode provider API, which disambiguates multiple instances per fwnode
via phandle cells. To make that landable as small, code-only commits,
the DT needs to carry the link index ahead of time.
Bump #pcs-cells from 0 to 1 on every SerDes node in the four SoC DTSIs
and append the link cell to every pcs-handle reference across boards
and the SWITCH_PORT_* macros. Cell values match the existing wiring:
0 for single-link SerDes (10GBase-R, SGMII, fiber, single-link
USXGMII), 0..3 per SerDes for QSGMII and USXGMII-QX, 0..7 for the
RTL9311 octal USXGMII layout.
No code reads the new cell yet -- of_parse_phandle_with_args() in the
PCS driver already cooperates with cells = 0 or 1, and the DSA glue
uses of_parse_phandle() which ignores cells entirely. The change is
runtime-neutral on its own; it exists so the follow-up code patches
can be a few lines each instead of dragging a bridge counter into the
driver to invent slot numbers DT could have provided directly.
Link: https://github.com/openwrt/openwrt/pull/23539
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Since f1f0572d1 ("remove redundant integrated phy attribute") the
phy-is-integrated attribute of an phy in the dts is obsolete.
This was important for the INTERNAL_PHY() macro. Now it is
useless. Convert the macro to its successor PHY_C22().
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22892
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devices contain a single MAC address in the U-Boot environment.
Set it as eth0 and label MAC in device tree. To maintain the current
state, the 02_network script still sets individual port MAC addresses
and the bridge MAC address.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22302
Signed-off-by: Robert Marko <robimarko@gmail.com>
In most drivers upstream use "ethernet-ports" instead of "ports"
in dts. Especially the upstream rtl9300 mdio driver uses this to
lookup the port/phy mapping. Do the same downstream. There is no
need to adapt the dsa driver because it scans the dts via
for_each_node_by_name(dn, "port").
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove all pseudo-PHYs and phy-handle properties from DTS of RTL838X
devices. RTL838X SerDes is now handled by PCS driver and thus not
treated as PHY anymore.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20876
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that MDIO and DSA driver only look for pcs-handle drop all
usages of the sds property.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20148
Signed-off-by: Robert Marko <robimarko@gmail.com>
For all switch ports where the assigned SerDes is known, add the new
pcs-handle to the dts. Leave the existing <sds> assignments to the
PHYs as is because the driver has not yet been updated.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20111
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mdio controller got its own dts node with a dedicated bus node.
Until now it still searches the phy nodes in the ethernet node.
Change the driver so it searches the nodes at the right location.
For this to work move the phy nodes in all dts/dtsi over to the new
bus node. Use the following replacement rule:
Replace old full declaration
ðernet0 {
mdio-bus {
...
};
};
and old abbreviated declaration
&mdio {
...
};
simply with the new declaration
&mdio_bus0 {
...
};
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19986
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
From now on both SFP ports can be used without manual intervention.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18737
Signed-off-by: Robert Marko <robimarko@gmail.com>
Change devices with RTL8231 GPIO expander definition that can easily be
translated to the new RTL8231 binding and carry over any gpio-hogs. This
will let them use the new RTL8231 MFD driver, without any functional
changes.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Hardware specification
----------------------
* RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
* 256MB DRAM
* 32MB NOR Flash
* 8 x 10/100/1000BASE-T ports
* 2 x SFP ports
* Power LED, Fault LED
* Reset button on front panel
* UART (115200 8N1) via populated standard pin header marked JP1
TODO: The SFP ports use a shared SCL GPIO that the driver cannot handle.
The left SFP port (lan9) is defined and fully functional while the laser
on the right SFP port (lan10) is off by default.
UART pinout
-----------
[o]ooo|JP1
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Installation using OEM webinterface
-----------------------------------
1. Make sure you are running OEM firmware in secondary slot
2. Install squashfs-factory.imag to primary slot by upload via http
Installation using serial interface
-----------------------------------
1. Press "a" "c" "p" during message "Enter correct key to stop autoboot"
2. Load image with "upgrade runtime <TFTP IP>:squashfs-sysupgrade.bin" command
3. Switch to primary slot with "setsys bootpartition 0"
4. Store config with "savesys"
5. Boot the image with `boota` command
Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------
From stock to OpenWrt / primary image 1 (CLI as admin):
- > boot system image1
- > reboot
From OpenWrt to stock / boot image 2: (shell as root)
- # fw_setsys bootpartition 1
- # reboot
Debrick using serial interface
------------------------------
1. Press "a" "c" "p" during message "Enter correct key to stop autoboot"
2. Load vendor image with "upgrade runtime <TFTP IP>:LGS310xxxxx.imag"
3. switch to primary partition "setsys bootpartition 0"
4. safe config "savesys"
Further documentation
---------------------
See https://openwrt.org/toh/linksys/lgs352c
It has been developed and tested on device with v1 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16068
[Add missing 'w' in name of firmware partition]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
