Device/zyxel_zynos sets COMPILE := loader-$(1).bin to drive the
standalone rt-loader build, but include/image.mk's Device/Init does
not reset COMPILE between TARGET_DEVICES iterations. When a non-zynos
device follows a zynos device, the stale COMPILE entry survives and
Device/Build/compile registers a second recipe for the previous
device's loader-*.bin target. Make warns about the override and the
second (wrong) recipe wins.
Reset COMPILE in Device/Default so each device starts with a clean
slate.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23226
Signed-off-by: Robert Marko <robimarko@gmail.com>
FLASH_ADDR is referenced inside Build/rt-loader-standalone but is not
listed in DEVICE_VARS, so include/image.mk's Device/Export does not
emit a per-target FLASH_ADDR := <value> assignment for the standalone
loader recipe. At recipe expansion time $(FLASH_ADDR) therefore
resolves to whatever value the last device in TARGET_DEVICES set
globally, which is not necessarily the value belonging to the loader
being built.
This currently happens to produce correct binaries only because every
device that sets FLASH_ADDR within a given subtarget shares the same
value, so the leaked global matches by coincidence.
Add FLASH_ADDR to DEVICE_VARS so each loader recipe captures its own
device's address.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23226
Signed-off-by: Robert Marko <robimarko@gmail.com>
These are all unused by the current targets, clean up and stop
irritating the user with irrelevant grep results.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23240
Signed-off-by: Robert Marko <robimarko@gmail.com>
Between 6.12 and 6.18, a 'blank' led_status_power has been added into
jh7110-common.dtsi. Update the patches responsible for adding the LED
aliases and add functionality for this LED entry.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Several defines still use the old prefix and are not sorted
alphabetically. Rearange the header file and the configuration
structures.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23145
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mdio driver has found a simple way to handle phy addresses
for all devices with upstream kernel defaults. Remove all unneeded
hacks from the corresponding patch and reword it.
While we are here increase DSA_MAX_PORTS to 56 to match RTL931x.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23186
Signed-off-by: Robert Marko <robimarko@gmail.com>
As of now RTL839x devices have never more than 32 devices on one
mdio bus. Harden the phy address check during probing.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23186
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL839x actually has two mdio busses.
- mdio bus 0 serves ports 0..23
- mdio bus 1 serves ports 24..51
This is baked into hardware and cannot be changed during mdio driver
setup with any register write. With the recent changes the driver
handles ports, phys and busses in a more logical way. So a port X
is assigned to a bus Y and a phy Z (on that bus). This gives a
mapping like
- port 16 <=> bus 0, address 16
- port 32 <=> bus 1, address 8
This unique assignment is used in the mdio driver as follows:
- Request to read bus 1, address 8
- Lookup corresponding port = 32
- Read from port 32
Looking at RTL839x it becomes clear that bus/phy => port lookup can
be achieved in multiple different ways. The simple reason is, that
for this device the driver cannot setup the smi topology. It is
baked into the hardware. So adding a "virtual" second bus does not
change the hardware access but allows to keep phy addresses below 32.
Making an example
mdio_bus0 {
PHY_C22(40, 40)
}
resolves to port 40. But the same can be achieved with
mdio_bus1 {
PHY_C22(40, 16)
}
In the first case the kernel sees bus/phy = 0/40 and in the second
case it sees bus/phy = 1/16. Both result in the access to the same
phy device on hardware port 40.
Use this analogy for RTL839x devices to match the real hardware
topology. For this change the existing dts and
- activate mdio bus 1 in rtl839x.dtsi
- rearrange devices with ports 24..51 to make use of bus 1
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23186
Signed-off-by: Robert Marko <robimarko@gmail.com>
The lm75 alert polarity active-high patch has been accepted upstream.
Replace the downstream version. Additionally add an upstream bugfix
that was identified during the implementation.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23232
Signed-off-by: Robert Marko <robimarko@gmail.com>
The wrapper address of simple image devices should have been changed
at commit 6a8b831 , but only TL-WDR4900 and BR200-WP are changed at
that time, and now the wrapper address changes are split among patches
for specific devices. More importantly, commit 6a8b831 forgot to
change Enterasys WS-AP3715i, causing
https://github.com/openwrt/openwrt/issues/23112 .
This commit will gather the change of wrapper address of simple image
devices into a dedicated patch file.
Tested: Both WS-AP3715i and TL-WDR4900 v1 boot well.
Fixes: https://github.com/openwrt/openwrt/issues/23112
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/23121
Signed-off-by: Robert Marko <robimarko@gmail.com>
The simpleImage contains a payload already compressed with lzma-based
xz (by default), so further compressing it with lzma will often make
the result larger. On the contrary, compressing these simpleImages
with gzip can make the result smaller, so replace lzma with
libdeflate-gzip to compress kernel for ws-ap3715i.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/23121
Signed-off-by: Robert Marko <robimarko@gmail.com>
find_mtd_part() outputs /dev/mtdblockX, to which fw_setenv cannot
write, "/dev/mtd$(find_mtd_index '<vol name>')" could be used instead.
The envsize should also be changed to 0x1000 to make the CRC checksum
valid and the env block recognized by the uboot-envtools, but the
flash sector size remains 0x10000, otherwise the env block will be
readable but not writable.
The "read-only" mark within device tree is also removed.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/23121
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the basic bits to allow 100base-FX SFP mode on the RTL8214FC.
While this looks good fom ethtool perspective, it does not really
change the phy registers to enforce the mode. The SFP is still
driven in 1000base-X.
While it might seem useless at the moment this at least opens
up a new phy control method. This comes handy with one known bug.
In rare cases a SFP that is plugged in during boot does not get
a link. One option to revive the dead port seems to be
root@OpenWrt:~# ethtool -s lan28 speed 100 duplex full autoneg off
rtl83xx-switch 1b000000.switchcore:ethernet-switch lan28: Link is Up - 100Mbps/Full - flow control off
switch: port 28(lan28) entered blocking state
switch: port 28(lan28) entered forwarding state
rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported
rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23087
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a nonsensical binding that's not implemented anywhere.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23137
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a meaningful define for RTL838x port 24-27 link status detection.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL838x devices do not have a fail indicator. Add a comment for that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
The C22 aka command register is a wild bit mix. Avoid confusion
for reviewers and add a comment.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Maximum devnum in c45 access is only 31. The bits 21-31 of the MMD
register are reserved and cannot be written. Nevertheless add a
proper mask to help AI review bots.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use park page (aka select page) to get rid of some magic values.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make clear that the hardware design always uses the same type
of 10G phys. So it is uncritical that the polling values are
overwritten multiple times.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
rtmdio_probe_one() should be only called by rtmdio_probe() after it
has validated the dts input. Nevertheless be defensive and add
another consistency check.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rename the module to describe that it is for the Realtek Otto
switches. Add owner to make clear who takes care. Adapt the
license to match the SPDX header.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
In case someone calls the macro with other helpers this might
break the code. Add brackets for consistency.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
The read functions might fail and thus "val" might be uninitialized.
The debug function will output the undefined state. Set the value
to zero to be consistent.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove the register write. It is never used in the SDK.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make the macro type safe.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL839x allows to add an extended page operator during phy
access. This is not needed for the standard linux kernel C22
access. Give the hardcoded 0x1ff value a meaningful define.
Although it is not needed, add the corresponding register define.
This makes clear where the mask belongs to.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rtmdio_931x_setup_ctrl() function currently initializes the c22/c45
and the proprietary format bit of the controller. This works because of
the order these calls are arranged. Narrow down the update to the really
needed bits.
- c22/c45 (bit 1) is updated here
- standard/proprietary (bit 0) is updated in rtmdio_931x_setup_polling()
Adapt the confusing comment "Std. C45, non-standard is 0x3" it basically
explains the other function.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Provide a separate function to setup the ability (SDS/MDIO) of a RTL930x
port. This simplifies rtmdio_930x_setup_polling(). With this commit the
driver does no longer unconditionally overwrite reserved register bits.
Add a return value for the new function to indicate failure/success. As
of now this will be silently ignored in the caller. A future commit will
take care about that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Provide a separate function to setup the ability (SDS/MDIO) of a RTL931x
port. This simplifies rtmdio_931x_setup_polling(). With this commit the
driver does no longer unconditionally overwrite reserved register bits.
Add a return value for the new function to indicate failure/success. As
of now this will be silently ignored in the caller. A future commit will
take care about that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix whitespace issues in the driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Improve error handling for the setup_ctrl() functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Topology setup is used during probing. Improve error checking
to be 100% sure that hardware setup works as expected. While
we are here:
- use GENMASK()
- Be type consistent and add u32 cast for value calculation
- use __ffs(mask) for code deduplication and better readability
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
The driver was developed over a longer time. Be consistent about
the return code handling and always use "ret" instead of "err".
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use device base warning messages and simplify message.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
With its current usage type RTMDIO_PHY_POLL_MMD() definition is ok.
But for the sake of consistency add brackets around the macro
parameters and use masks to avoid calculation inconsistencies.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mdio hardware is fully understood. Describe the number of real
busses in the configuration structure and check against this limit
when working on busses.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Try to describe the hardware capabilities with consistent defines
and configuration variables. As raw_page is always num_pages - 1
better use num_pages naming where needed and provide a macro that
converts this naming.
While we are here:
- Sort the configuration variables alphabetically
- Provide num_pages defines per architecture
- adapt RTMDIO_839X_C22_DATA() macro to use the new define
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23204
Signed-off-by: Robert Marko <robimarko@gmail.com>
Harmonize the read/write functions for better readability. This
aligns with the naming convention of the upstream rtl9300 mdio
driver.
read_phy -> read_c22
read_phy_mmd -> read_c45
write_phy -> write_c22
write_phy_mmd -> write_c45
Swap order of c22/c45 functions to keep structures sorted
alphabetically.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/23197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for changing the LED mode via the device tree.
Currently it always defaults to SERIAL mode. With this change,
one can also use the SINGLE_COLOR_SCAN and BI_COLOR_SCAN modes.
Signed-off-by: Manuel Stocker <mensi@mensi.ch>
Link: https://github.com/openwrt/openwrt/pull/23160
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WRC-X6000GSD is a 4804Mbps 4xMIMO 2.4/5 GHz 11ax (Wi-Fi 6) router
with 2.5Gbps WAN (stock: 1Gbps max.), based on MT7986B
Specification:
- SoC : MediaTek MT7986BLA
- RAM : DDR3 512 MiB (SoC)
- Flash : Winbond 128MiB SPI NAND (W25N01GVZEIG)
- WLAN : 2.4/5 GHz 4T4R (MediaTek MT7986)
- Ethernet : 5x 10/100/1000(/2500) Mbps
- wan : Maxlinear Ethernet GPY211C (max. 2500M)
- lan : MediaTek MT7531 (max. 1000M)
- LEDs/Keys (GPIO): 11x/4x
- UART : through-hole on PCB (J1)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 2 A
Flash layout:
dev: offset size name
mtd0: 0x00000000 0x00100000 "BL2"
mtd1: 0x00100000 0x00080000 "Ubootenv"
mtd2: 0x00180000 0x00200000 "Factory"
mtd3: 0x00380000 0x00200000 "FIP"
mtd4: 0x00580000 0x00020000 "Fwheader"
mtd5: 0x005a0000 0x03200000 "ubi"
mtd6: 0x037a0000 0x00380000 "Config"
mtd7: 0x03b20000 0x00020000 "Fwheader_2"
mtd8: 0x03b40000 0x03200000 "ubi_2"
mtd9: 0x06d40000 0x00380000 "Config_2"
mtd10: 0x070c0000 0x00100000 "persist"
mtd11: 0x071c0000 0x00040000 "Mrd"
mtd12: 0x07200000 0x00380000 "Backup"
Flash instruction using factory.bin image:
1. Boot WRC-X6000GSD in router mode normally
2. Access to the WebUI ("http://192.168.2.1/") on the device
-> その他設定 (Other settings)
-> フォームウェア更新 (Update firmware)
-> ローカルファイル指定 (Specify local file)
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of firmware partition
mstc_rw_bootnum
3. Set the bootnum to opposite value between 1 and 2
mstc_rw_bootnum value
example:
- step2 returned "1": mstc_rw_bootnum 2
- step2 returned "2": mstc_rw_bootnum 1
4. Reboot, to stock FW
5. Flash the stock FW to fuly revert back to original.
Notes:
- With the stock firmware, it will flash to another partition and
toggle boot to that partition when any firmware is flashed.
For example when booting on ubi, the new firmware will be flashed
to ubi_2 and the router will boot from ubi_2 afterwards.
The 5th byte of the Persist partition is the boot value (0x01 or 0x02).
- bootmenu_delay=0 is set from factory so uboot menu is hidden by
default.
- The hardware of WRC-X6000GSD is almost identical to WRC-X6000QS, but
WAN (labeled as "INTERNET") port is limited to 1000 Mbps on stock FW.
On OpenWrt FW, 2500 Mbps connection is available on that port.
MAC Addresses:
LAN : 38:97:A4:xx:xx:58 (Factory, 0x2A(hex)/Ubootenv, "ethaddr"(text))
WAN : 38:97:A4:xx:xx:5B (Factory, 0x24(hex))
2.4GHz: 38:97:A4:xx:xx:59 (Factory, 0x4(hex))
5GHz : 38:97:A4:xx:xx:5A (Factory, 0xA(hex)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WRC-X6000QS is a 4804Mbps 4xMIMO 2.4/5 GHz 11ax (Wi-Fi 6) router
with 2.5Gbps WAN, based on MT7986b
Specification:
- SoC : MediaTek MT7986B
- RAM : DDR3 512 MiB
- Flash : Winbond 128MiB SPI NAND
- WLAN : 2.4/5 GHz 4T4R (MediaTek MT7986)
- Ethernet : 5x 10/100/1000 Mbps
- wan : Maxlinear Ethernet GPY211C
- lan : MediaTek MT7531
- LEDs/Keys (GPIO): 11x/4x
- UART : through-hole on PCB (J1)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 2 A
Flash layout:
dev: offset size name
mtd0: 0x00000000 0x00100000 "BL2"
mtd1: 0x00100000 0x00080000 "Ubootenv"
mtd2: 0x00180000 0x00200000 "Factory"
mtd3: 0x00380000 0x00200000 "FIP"
mtd4: 0x00580000 0x00020000 "Fwheader"
mtd5: 0x005a0000 0x03200000 "ubi"
mtd6: 0x037a0000 0x00380000 "Config"
mtd7: 0x03b20000 0x00020000 "Fwheader_2"
mtd8: 0x03b40000 0x03200000 "ubi_2"
mtd9: 0x06d40000 0x00380000 "Config_2"
mtd10: 0x070c0000 0x00100000 "persist"
mtd11: 0x071c0000 0x00040000 "Mrd"
mtd12: 0x07200000 0x00380000 "Backup"
UBI layout:
name: size:
kernel 0x00364000 dynamic
rootfs 0x00FFC000 dynamic
rootfs_data 0x01A47000 dynamic
Flash instruction using factory.bin image:
1. Boot WRC-X6000QS in router mode normally
2. Access to the WebUI ("http://192.168.2.1/") on the device
-> その他設定 (Other settings)
-> フォームウェア更新 (Update firmware)
-> ローカルファイル指定 (Specify local file)
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of firmware partition
mstc_rw_bootnum
3. Set the bootnum to opposite value between 1 and 2
mstc_rw_bootnum value
example:
- step2 returned "1": mstc_rw_bootnum 2
- step2 returned "2": mstc_rw_bootnum 1
4. Reboot, to stock FW
5. Flash the stock FW to fuly revert back to original.
Note 1: With the stock firmware, it will flash to another partition and
toggle boot to that partition when any firmware is flashed.
For example when booting on ubi, the new firmware will be flashed
to ubi_2 and the router will boot from ubi_2 afterwards.
The 5th byte of the Persist partition is the boot value (0x01 or 0x02).
During my tests, it never switched to another boot partition if the
firmware failed boot. So if openwrt doesn't boot,
UART might be required to recover.
Note 2: bootmenu_delay=0 is set from factory so uboot menu is hidden.
[original work]
Signed-off-by: Yuhei Amemiya <minihui@me.com>
[fixes, improvements]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use SWITCH_PORT_LED instead of full verbose port definitions to
simplify and clean up the DTS.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace the verbose ethernet-phy node definitions with the PHY_C45 and
PHY_C45_PAIR_ORDER macros to drop boilerplate.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace the raw bitmask values for led_set entries with the
RTL93XX_LED_SET_* macros from macros.dtsi to make the LED configuration
self-explanatory.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
