Drop config and patches for Linux 6.6.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/20468
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to Linux kernel 6.12.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/20468
Signed-off-by: Nick Hainke <vincent@systemli.org>
Backport upstream patch for AN7583 Ethernet support. While at it also
backport some additional fixes required to apply the AN7583 patches
cleanly.
Refresh all affected patch automatically (aside from the XSI patch that
changed the implementation)
Link: https://github.com/openwrt/openwrt/pull/20489
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport phylink patches for PCS/PHY caps OPs. This makes it easier to
align future generic PCS patch and permit supporting special PHY that
needs specific tune if "in-band" mode is enabled (for example Aeonsemi
PHYs)
This is also mainly using the upstream version of the Mediatek patch
739-net-add-negotiation-of-in-band-capabilities.
All affected patch automatically refreshed.
Link: https://github.com/openwrt/openwrt/pull/20461
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v2 and add ipq-wifi package for it.
Tested-by: Semih Baskan <strstgs@gmail.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Signed-off-by: Robert Marko <robimarko@gmail.com>
L3 Offloading caused DHCP packets to be dropped at hardware level
And potentially buggy route implementation can cause a crash
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20208
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL931x is not supporting L3 offloading at the moment. To avoid crashes
when using this switch, simply disable L3 offloading completely.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20208
Signed-off-by: Robert Marko <robimarko@gmail.com>
a33d59f7af (2025-10-14) restored dts files for kernel 6.6 to files-6.6
after the preceding 15fa59c41f moved files-6.6 to files-6.12 to be
used by the new testing kernel, 6.12. This restoration omitted
1a3f05eb2b (2025-10-08), which fixed important aspects of the wifi
device definitions in qcom-ipq8064-eax500.dtsi and
qcom-ipq8064-unifi-ac-hd.dts.
The 1a3f05eb2b fix persisted into the 6.12 dts files. This change now
restores it for 6.6. Note that ipq806x is currently using kernel 6.6 for
most purposes, as 6.12 is only in testing status for this target.
This change was prepared with `git diff
a33d59f7af8f:target/linux/ipq806x/files-6.6
15fa59c41f0d^:target/linux/ipq806x/files-6.6`. This identified
c186d17fa5 (2025-10-08) as another change that was not present in the
restored files-6.6, but it has since been superseded by 2a709d108e
(2025-10-20), so no action is necessary to restore it. There were no
diffs present between these revisions in config-6.6 or patches-6.6,
which were also moved and restored in the 6.12 bring-up.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Cc: Shiji Yang <yangshiji66@outlook.com>
Cc: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20464
Signed-off-by: Robert Marko <robimarko@gmail.com>
SQUASHFS_DECOMP_MULTI_PERCPU is selected by
SQUASHFS_COMPILE_DECOMP_MULTI_PERCPU, so add it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The pinctrl driver should be enabled based on the SoC supported
by the subtarget, rather than enabling all by default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the common kernel config found when 'make kernel_oldconfig'.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The cortexa53 target currently uses cpu erratums for Cortex-A510,
Cortex-A710, and Neoverse-N2. Remove them and enable cpu erratums
for Cortex-A53.
Fixes: f01982e ("sunxi: add testing kernel 6.1")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SPI chip select GPIO polarity is active low by default. We must
use "spi-cs-high" dts property to toggle the polarity. The polarity
on "cs-gpios" won't take effect at all[1]. Fix these incorrect GPIO
polarities to silence the kernel warnings.
[1] Refer to Linux/Documentation/devicetree/bindings/spi/spi-controller.yaml
```
device node | cs-gpio | CS pin state active | Note
================+===============+=====================+=====
spi-cs-high | - | H |
- | - | L |
spi-cs-high | ACTIVE_HIGH | H |
- | ACTIVE_HIGH | L | 1
spi-cs-high | ACTIVE_LOW | H | 2
- | ACTIVE_LOW | L |
Notes:
1) Should print a warning about polarity inversion.
Here it would be wise to avoid and define the gpio as
ACTIVE_LOW.
2) Should print a warning about polarity inversion
because ACTIVE_LOW is overridden by spi-cs-high.
Should be generally avoided and be replaced by
spi-cs-high + ACTIVE_HIGH.
```
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is no need to add a "cs-gpios" property if chip select pin is
directly controlled by the SPI host hardware.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices only have one SPI peripheral. And the chip select pin is
directly controlled by the SPI host hardware. Hence we don't need to
assign empty GPIO phandle for them. This patch also adjust the reg
address of the SPI peripheral node to follow the cs-gpios changes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SPI chip select GPIO polarity is active low by default. We must
use "spi-cs-high" dts property to toggle the polarity. The polarity
on "cs-gpios" won't take effect at all[1]. Fix these incorrect GPIO
polarities to silence the kernel warnings.
[1] Refer to Linux/Documentation/devicetree/bindings/spi/spi-controller.yaml
```
device node | cs-gpio | CS pin state active | Note
================+===============+=====================+=====
spi-cs-high | - | H |
- | - | L |
spi-cs-high | ACTIVE_HIGH | H |
- | ACTIVE_HIGH | L | 1
spi-cs-high | ACTIVE_LOW | H | 2
- | ACTIVE_LOW | L |
Notes:
1) Should print a warning about polarity inversion.
Here it would be wise to avoid and define the gpio as
ACTIVE_LOW.
2) Should print a warning about polarity inversion
because ACTIVE_LOW is overridden by spi-cs-high.
Should be generally avoided and be replaced by
spi-cs-high + ACTIVE_HIGH.
```
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SPI chip select GPIO polarity is active low by default. We must
use "spi-cs-high" dts property to toggle the polarity. The polarity
on "cs-gpios" won't take effect at all[1]. Fix these incorrect GPIO
polarities to silence the kernel warnings.
[1] Refer to Linux/Documentation/devicetree/bindings/spi/spi-controller.yaml
```
device node | cs-gpio | CS pin state active | Note
================+===============+=====================+=====
spi-cs-high | - | H |
- | - | L |
spi-cs-high | ACTIVE_HIGH | H |
- | ACTIVE_HIGH | L | 1
spi-cs-high | ACTIVE_LOW | H | 2
- | ACTIVE_LOW | L |
Notes:
1) Should print a warning about polarity inversion.
Here it would be wise to avoid and define the gpio as
ACTIVE_LOW.
2) Should print a warning about polarity inversion
because ACTIVE_LOW is overridden by spi-cs-high.
Should be generally avoided and be replaced by
spi-cs-high + ACTIVE_HIGH.
```
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a useless property on ath79 target. Both spi-ar934x and
spi-ath79 drivers don't check num-cs property. They always set
chip select number to 3.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both devices seem to be completely identical and D-Link doesnt even
mention the DIR-X1550 A1 in the GPL source. Furthermore the supported
devices header also just contains DIR-X1860 B1. The cherry on top is the
FCC filing, which features the manual for DIR-X1550 A1 but the label
info for DIR-X1860 B1. I guess someone at D-Link was just as confused as
me.
Hardware
--------
SOC: MediaTek MT7621AT
FLASH: 128MB (Spansion S34ML01G200TF100)
RAM: 256MB (Winbond W632GU6NB-12)
WIFI: MediaTek MT7915DAN + MT7975DN DBDC 2x2 802.11ax
ETH: 1x WAN, 3x LAN
LED: 6 (4 GPIO controllable, 2 WIFI hardwired)
BTN: WPS, Reset
UART: 115200 8N1 (Pinout silkscreened) - ignore VCC
MAC addresses
-------------
LAN Label MAC (stored in config2 partition as ASCII (entry
factory_mac=xx:xx:xx:xx:xx:xx))
WAN LAN + 3
2.4G LAN + 1
5G LAN + 2
Installation
------------
Vendor UI
---------
1. Browse to http://192.168.0.1 and login.
2. Navigate to "Management" -> "Upgrade".
3. Press the "Select File" button and upload
openwrt-ramips-mt7621-dlink_dir-x1860-b1-squashfs-factory.bin
4. Confirm the security questions, wait for a reboot and enjoy OpenWrt.
Recovery UI
-----------
1. Set your IP address to 192.168.0.101, subnet 255.255.255.0.
2. Power on the device while holding reset.
3. Release reset once the status led starts to blink orange.
4. Open a chrome- or firefox based browser and browse to
https://192.168.0.1
5. Upload openwrt-ramips-mt7621-dlink_dir-x1860-b1-squashfs-recovery.bin
wait for a reboot and enjoy OpenWrt.
Back to stock
-------------
1. Set your IP address to 192.168.0.101, subnet 255.255.255.0.
2. Power on the device while holding reset.
3. Release reset once the status led starts to blink orange.
4. Open a chrome- or firefox based browser and browse to
https://192.168.0.1
5. Upload a decrypted vendor image, wait for a reboot and regret your
decision.
Decrypt vendor image
--------------------
1. Download dlink-sge-image.c and dlink-sge-image.h from the
firmware-utils openwrt repository.
2. Compile a binary from the downloaded file
e.g. gcc dlink-sge-image.c -lcrypto -o dlink-sge-image
3. Run
./dlink-sge-image DIR-X1860-B1 <vendor_image> <decrypted_image> -d
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20410
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Originally, phylink_mac_config first disabled the MAC, then triggered
the SerDes setup and then re-enabled MAC. SerDes setup has been moved to
the PCS driver now but pcs_config is called AFTER phylink_mac_config by
phylink subsystem.
Thus, just disable the MAC in phylink_mac_config. After PCS has setup
the SerDes, the MAC should be properly brought up in a mac_link_up call
coming from the phylink subsystem.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20369
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove SerDes initialization/configuration calls from the DSA driver in
'rtl931x_phylink_mac_config' and let our PCS driver setup the SerDes now
that the driver is able to do that.
pcs_config of the PCS driver is automatically called by phylink, thus
there's no need to call it on our own.
Note that in rtl931x_phylink_mac_config the MAC is enabled before
pcs_config is called. While this seems to work, it isn't good and needs
to be fixed.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20369
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In rtpcs_931x_setup_serdes, quit early on USXGMII mode. This restores
the behaviour introduced in c18476d0c5 to prevent the current buggy
procedure to destroy a working configuration established by U-Boot
before.
Also include the valuable comment from the code to keep the information.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20369
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adjust the SerDes page numbers to account for the different mapping used
by 'mdio-realtek-otto' and 'mdio-realtek-otto-serdes' drivers.
While importing the SerDes configuration code from PHY driver to PCS
driver, all helper calls to access the SerDes registers had to be
adjusted to use the proper helpers within the PCS driver. However, there
is one important implication of this: 'mdio-realtek-otto' and
'mdio-realtek-otto-serdes' use a slightly different page mapping.
While the old helpers in 'mdio-realtek-otto' used a page mapping of
0x00/0x100/0x200, 'mdio-realtek-otto-serdes' uses a mapping of
0x00/0x40/0x80 to provide consumers with the ability to only operate on
frontend SerDes. Thus, all page numbers > 63/0x3f have to be adjusted
like the following:
before: rtsds_931x_write_field(sds, 0x101, ... // old helper calls
after: rtpcs_sds_write(ctrl, sds, 0x41, ...
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20369
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replaces the "old" way of accessing registers using the macros
sw_r32/sw_w32 from mach-rtl83xx.h. The "new" way to access register is
through the regmap API.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20369
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Let's start this transition with RTL931X.
Import all functions starting with 'rtl931x_' or 'rtsds_931x' from PHY
driver into the PCS driver, rename all functions to match a common
naming scheme and adjust signature, helper calls and function calls
accordingly to make it work within the PCS driver.
This is just copy&paste and tries to do only mandatory adjustments. The
code will be refactored in succeeding commits.
Also remove 'unused' attribute from helpers as they are used now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20369
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL8261N is not used by any device in this target. If necessary, newly added
devices should add the kmod-phy-rtl8261n package.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20444
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This option will only take effect when the "separate_ramdisk"
feature was enabled. However, this target does not support
this feature. It is an obvious copy and paste issue.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17832
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This option will only take effect when the "separate_ramdisk"
feature was enabled. However, this target does not support
this feature. It is an obvious copy and paste issue.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17832
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Nokia G-240G-E is an xPON device with an EN7526G, 256M of
memory and 128M of flash. It has 1 USB2 port as well as phone and
ethernet but no wifi. Flashing instructions are per the typical
process using xmodem in the bootloader. This and other things
are described here: https://openwrt.org/inbox/toh/bt/g-240g-e_1
In addition, a generic image is offered, this image can be loaded
into memory from within the bootloader and launched directly. It
is recommended on the wiki of G-240G-E and other EcoNet devices
to be used for backing up the flash before flashing OpenWRT.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The #address-cells should be 1 according to the dt-binding document.
This patch fixes the following dtc warnings:
../dts/mt7621_gemtek_wvrtm-130acn.dts:46.4-14: Warning (reg_format): /pcie@1e140000/pcie@0,0/wifi@0,0/band@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 0)
../dts/mt7621_gemtek_wvrtm-130acn.dts:54.4-14: Warning (reg_format): /pcie@1e140000/pcie@0,0/wifi@0,0/band@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 0)
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set the reg property value based on node name "pca9547@77". This
patch fixes the following dtc warning:
watchguard-firebox-m300.dts:364.14-366.5: Warning (i2c_bus_reg): /soc@ffe000000/i2c@118000/pca9547@77: missing or empty reg property
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Trim unnecessary 0s from the node name to fix the dtc warnings:
cn9131-puzzle-m901.dts:43.18-46.4: Warning (unit_address_format): /memory@00000000: unit name should not have leading 0s
cn9130-clearfog-pro.dts:33.18-36.4: Warning (unit_address_format): /memory@00000000: unit name should not have leading 0s
cn9132-puzzle-m902.dts:50.18-53.4: Warning (unit_address_format): /memory@00000000: unit name should not have leading 0s
armada-385-wd_cloud-mirror-gen2.dts:148.26-152.9: Warning (unit_address_format): /soc/internal-regs/nand-controller@d0000/nand@0/partitions/partition@00000000: unit name should not have leading 0s
armada-385-wd_cloud-mirror-gen2.dts:154.26-157.9: Warning (unit_address_format): /soc/internal-regs/nand-controller@d0000/nand@0/partitions/partition@00500000: unit name should not have leading 0s
armada-385-wd_cloud-mirror-gen2.dts:159.26-163.9: Warning (unit_address_format): /soc/internal-regs/nand-controller@d0000/nand@0/partitions/partition@00a00000: unit name should not have leading 0s
armada-385-wd_cloud-mirror-gen2.dts:165.26-168.9: Warning (unit_address_format): /soc/internal-regs/nand-controller@d0000/nand@0/partitions/partition@00f00000: unit name should not have leading 0s
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Add the missing ranges property for PCIe bridge node.
- Correct the PCIe device node name.
This patch fix the following dtc warning:
../dts/bcm6328-dlink-dsl-2750b-b1.dts:203.9-220.4: Warning (pci_bridge): /ubus/pcie@10e40000/pcie@0: missing ranges for PCI bridge (or not a bridge)
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DTC recommends using wifi@0,0 as the node name to match the reg
property structure. Fix warning:
../dts/qca9557_fortinet_fap-221-c.dts:208.13-213.4: Warning (pci_device_reg): /ahb/pcie@180c0000/wifi@0,0,0: PCI unit address format error, expected "0,0"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
rev B1 is identical to rev A1 except for different PHYs on the 2.5gbps ports (lan9 and lan10)
Both revisions of xgs1210-12 are also switched to use rt-loader to avoid
problems due to overwriting the compressed image in memory when flashing
with the oem firmware (and also to save flash space with respect to gzip
compression)
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20161
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both devices, the Linksys WHW01 and the VLP01, are essentially the same
device. Even Linksys provides only one image for both devices which uses
the WHW01 identifier in the image header.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20455
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR30H. The MR30H is a POE
powered 802.11ac access point with an integrated 5 port Gigabit switch.
MR30H hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac, QCA9889 802.11/b/g/n/ac scanning radio
* Serial: Internal header (J8, 2.54mm, populated)
LAN5 (rear) is for POE input. LAN4 has POE output (802.3af) when powered
by an 802.3at source.
The LAN4 port is used for tftp booting in U-Boot.
This device does not have secure boot, but cannot be flashed without
external programmers (TSOP48 NAND) as Meraki disabled interrupting U-Boot
for any device that updated after ~2017.
Disassembly:
* Remove the two T10 screws on the rear of the AP.
* Using a guitar pick or similar plastic tool, insert it on the side between
the grey metal plate and the white plastic body and pry up gently.
* The rubberised border on the metal plate does not need to be removed.
* The metal back plate has several latches around the perimeter (but none on
the bottom by the Ethernet ports).
* Once you have removed the metal back plate, push up gently on the bottom
Ethernet ports while pulling gently on the rear-mounted Ethernet port to remove
the PCB.
* The PCB should come free from the plastic housing, pull the bottom
(4 Ethernet ports) up as if you are opening a book.
* If done carefully, there is no need to remove the WiFi antenna connectors
to access the NAND flash.
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
opposite side of the PCB.
* To flash, you need to desolder the TSOP48 or use a 360 clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr30h
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Resolder the NAND after overwriting the `u-boot` regions.
OpenWrt Installation:
* After flashing NAND with the external programmer. Plug an Ethernet
cable into port 4. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Alternative installation steps if your device has U-Boot older than:
`U-Boot 2017.07-RELEASE-g78ed34f31579 (Sep 29 2017 - 07:43:44 -0700)`
**BIG FAT WARNING BEGIN**
Attmping to interrupt boot on a newer U-Boot release may permanently
brick your device! See: riptidewave93/LEDE-MR33#13
**BIG FAT WARNING END**
* Use `ubootwrite.py` from the above GitHub repository to transfer the
`u-boot.itb`
image to the router.
```
./ubootwrite.py --serial=/dev/ttyUSB0 --write u-boot.itb
```
* To avoid bricking your router, it is highly recommended at this point that
you flash the unlocked U-Boot to the `part.safe` ubi volume.
```
run set_ubi && ubi write $loadaddr part.safe 0x2fd48
```
* Power cycle the router. The stock Meraki U-Boot will boot `part.safe` which
is now the unlocked U-Boot.
* Use the new U-Boot build (`" "` to interrupt boot) to
`tftpboot` the OpenWrt initramfs image:
```
dhcp
setenv serverip <tftp_server_addr>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
bootm
```
* It is only recommended to flash U-Boot to the `u-boot` NAND region from
Linux:
```
insmod mtd-rw i_want_a_brick=1
```
* Copy `u-boot.elf` to the router:
```
scp -O u-boot.elf root@192.168.1.1:/tmp/
```
Note: If any of the below commands fails, YOU WILL HAVE A BRICK IF YOU
REBOOT OR LOSE POWER. Only a hardware programmer can recover the device.
```
flash_erase /dev/mtd8 0 0
nandwrite -p /dev/mtd8 /tmp/u-boot.elf
```
Note: ONLY use `u-boot.elf` when flashing the `u-boot` region (`/dev/mtd8`);
`u-boot.bin` or `u-boot.itb` will BRICK YOUR DEVICE
* `scp` the `sysupgrade` image to the device and run the normal `sysupgrade`
procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Go GX20. The Go GX20 is a wired
router with 5 port Gigabit switch. It shares the same PCB as the Meraki Z3,
but without the WiFi radios.
GX20 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x2b`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_gx20-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_gx20-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_gx20-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Z3. The Z3 is a "teleworker"
device with 802.11ac and an integrated 5 port Gigabit switch.
Z3 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x24`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_z3-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubimkvol /dev/ubi0 -N ART -s 524288
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
whw01 was incorrectly placed below whw03 definitions.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds led aliases for failsafe and upgrade. Before this change the
leds stayed dark in both situations.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the label-mac-device to be able to easily fetch the mac-address of
the device, which is printed on the bottom of the case.
While at it, remove the TODO - the ethernet0 alias is needed to get the
mac from bootloader.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
kernel 6.9 removed the KConfig entry our RouterBOOT watchdog pet hack was relying on:
Linux df59427a1122 ("ARM: qcom: merge remaining subplatforms into sensible Kconfig entry")
Introduce a new specific KConfig entry for this hack,
and enable it for Mikrotik ipq40xx kernel.
CONFIG_ARCH_QCOM_IPQ40XX_BOOT_COMPRESSED_PET_WATCHDOG_EARLY
With appropriate DEBUG_LL and DEBUG_UNCOMPRESS, this watchdog reset
can be typically seen on console as a reset before "Uncompressing Linux..."
reaches " done, booting the kernel."
RouterBOOT
loading kernel... OK
setting up elf image... OK
jumping to kernel code
Jumping to kernel
DTB:0x80381A60 (0x000048C4)
C:0x800000E0-0x80386420->0x80FAB500-0x81331840
DTB:0x8132CE80 (0x000049B8)
Uncompressing Linux...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00096
versus:
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
On Mikrotik RouterBOOT devices, this is complicated by some RouterBOOT
versions successfully loading the same kernel that other RouterBOOT versions fail. Example:
RouterBOOT backup booter 6.45.9 fine, RouterBOOT booter 7.16 fail
Fixes: openwrt#19841
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Link: https://github.com/openwrt/openwrt/pull/20305
Signed-off-by: Robert Marko <robimarko@gmail.com>
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_MTD_CFI was disabled in p1010 subtarget.
It causes problem with Aerohive BR200-WP router.
This patch enables CONFIG_MTD_CFI in p1010 config-default file.
Fixes: e9dd6da916 ("mpc85xx: p1010: add missing symbols")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20419
Signed-off-by: Nick Hainke <vincent@systemli.org>
The DSA driver must flush the HW FDB when a port changes from
learning/forwarding to disabled/blocking/listening.
But the implementation for RTL931x was writing the port information
starting at bit 11 (bit 11 of the second 32-bit L2_TBL_FLUSH_CTRL
register). But this offset is the AGG_VID and not the port. The actual
position is 43 (bit 11 of the first register).
As result, the FDB was always only flushed for the port 0 and not for the
selected port.
Fixes: 9ed6097054 ("realtek: Add HW support for RTL931X for PIE, L2 and STP aging")
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20422
Signed-off-by: Robert Marko <robimarko@gmail.com>
the eth1 interface was renamed to wan so also reflect that change in
the leds setup script
Fixes: f26260c7e7 ("mediatek: filogic: Add label wan and cpu for Zyxel EX5601-T0")
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20120
Signed-off-by: Nick Hainke <vincent@systemli.org>
BPDU frames like STP must be processed by each switch (bridge) which
supports STP. It must not be forwarded to avoid confusing the STP state of
other STP participants. It is essential to be an active participant of STP.
The software bridge automatically takes care of forwarding the BPDUs to
other ports when STP is disabled and the hardware switch should not
interfere.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20414
Signed-off-by: Robert Marko <robimarko@gmail.com>
With this patch is set the maximum number of connections per ip address instead of no control.
The default is 8.
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20377
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
backport from kernel 6.12
ksmbd.mount will give each interfaces list and bind_interfaces_only flags
to ksmbd server. Previously, the interfaces list was sent only
when bind_interfaces_only was enabled.
ksmbd server browse only interfaces list given from ksmbd.conf on
FSCTL_QUERY_INTERFACE_INFO IOCTL.
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20377
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch resolves the LAN port not initializing on the
FriendlyElec NanoPI R4S, especially during warm reboots.
Upstream commit patch is based on:
c3fe7071e1
I've experienced the LAN port failing to initialize from a cold boot and
after a reboot. Other users have reported this issue on
https://forum.openwrt.org/t/nanopi-r4s-rk3399-is-a-great-new-openwrt-device/79143.
The NanoPI R4S has its LAN port connected to the RK3399 via PCIE. Since the
PCIE lanes don't initialize correctly after reboot, the LAN port
doesn't initialize.
Signed-off-by: Timothy Feierabend <tim.feierabend@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20406
Signed-off-by: Nick Hainke <vincent@systemli.org>
Now that we have a board file, add calibration variant for TP-Link
Archer C59 v1 and add ipq-wifi package for it.
Tested-by: Mateusz Jończyk <matjon@users.noreply.github.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 468975a985 changed the XO board clock definition from a fixed
clock to a fixed rate clock in the dtsi.
As such, boards must use clock dividers and multipliers to calculate
the clock rate based on the referenced parent clock.
Fixes: 5d2994a73e ("qualcommax: ipq50xx: Add support for Yuncore AX850")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20405
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a regression introduced by a recent commit.
It looks like a copy/paste error.
Add the missing line which defines the 'board' val
as it does not exist otherwise in the case check.
This fixes sysupgrade on ath79 MikroTik non-NOR boards.
Fixes: 318f07c231 ("ath79: mikrotik: check RouterBOOT version matching sysupgrade image")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Add pending patch to address PCI sysfs creation entry race observed on
ipq806x. This is to handle a kernel warning on creating the same sysfs
entry multiple times.
All affected patch automatically refreshed.
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adapt OPP patch with upstream changes to cpufreq driver. Use the krait
compatible and the new opp-supported-hw way instead of deleting nodes.
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The 6.12 testing kernel for ipq806x target is ready now.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- Reuse the bridges node defined on "qcom-ipq8064.dtsi".
- Rename PCIe device nodes to unified "wifi@0,0".
- Add the missing "qcom,ath10k" compatibles.
- Remove unseless property "interrupt-controller". There are no
consumers use these PCIe devices as interrupt controllers.
- Change bus number from 0 to 1, just like other ipq806x devices.
The valid PCIe bus range on this platform is 1 - 255.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add bridge node labels so that we can insert PCIe peripheral nodes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Copy patches and kernel configs from 6.12 kernel to restore the
default 6.6 kernel support files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is a preparation for 6.12 kernel support. It can help us
track the patches and Kconfig history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is a preparation for introducing the 6.12 kernel support.
All configs are automatically refreshed. In theory, they will
generate the same .config files in the kernel build directory
as before.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Right now the phylink capability function enables 2.5G and 10G modes on
Maple and Cypress, which they mostly (other than two SERDES on Cypress)
don't support. This causes these modes to be selected and break the link
as they are not supported by hardware.
I looked into doing this properly, but it cannot just be done based on
SoC, but needs to take the whole topology into account as a given MAC
might have very different capabilities depending on what SERDES are
assigned to it. So for now just use 1G and QSGMII for RTL83xx and 10G
for RTL93xx. This mostly works, except it will downgrade some 10G links
on RTL839x, but since there are also 1G SFPs on these this cannot be
solved without fully accounting for the global MAC and SERDES
configuration.
So this makes all of the 1G SFP slots work again, while keeping most of
the 10G SFP+ slots working at 10G with minimal changes.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/20374
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the devicetree contains the appropriate nodes to configure the MAC
addresses for each physical DSA port, then these MAC addresses must be used
in OpenWrt and not some automatically generated ones. Otherwise the device
often ends up with addresses which are locally administered and not
matching any expected port-to-MAC scheme.
Devices which only get the MAC address for eth0 must still auto-generate
these MAC addresses until the devicetree was updated to also include the
correct ones.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the lan_mac cannot be found, it is still used (as empty string) in
various operations. This is not valid and other 02_network scripts checking
for a non-empty string before using it. This should also be adopted for the
realtek 02_network.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Having everything in a big script without any structure makes it
unnecessary hard to get an overview or modify it without triggering
unexpected side effects.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The preferred prefix for the Realtek DSA driver code is "rtldsa" and no
longer "rtl83xx". This makes sure that the different drivers have
non-conflicting prefixes and because of this non-conflicting function
names.
Suggested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL930x and the RTL931x SoC families share the same struct
dsa_switch_ops. This should be represented in the name of the object.
Suggested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
If two ports are in isolation mode then these ports are not supposed to be
able to communicate between each other. This can be achieved in the realtek
switch by removing the other isolated port(s) from the port list of an
isolated port.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
The realtek driver is now in full control of the port matrix. It doesn't
need to rely on the current state of the HW to adjust it. The new port
matrix is calculated automatically using rtldsa_update_port_member() and
then written to the registers/tables.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
