f5d17dd60a89 mstp: add default Hello Time constant
17c36bebada1 mstp: use default Hello Time in recordTimes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add a function to allow drivers to query the pending AQL airtime
for a given txq, for both unicast and broadcast.
This will be used for mt76 to limit buffering in AP mode for power-save
stations.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ELECOM WRC-X3000GST2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router based on
IPQ5018. The only hardware difference from the WRC-X3000GS2 is the RAM
capacity; all other peripherals are identical. This port therefore
reuses the GS2 board-2.bin (ipq-wifi-elecom_wrc-x3000gs2) and ath11k
calibration variant.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 512 MiB (Kingston Technology D2516ECMDXGJD)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm QCN6122
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x / 3x (reset, WPS, router/AP slide switch)
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using factory.bin image:
1. Boot WRC-X3000GST2 normally in router mode
2. Access the WebUI ("http://192.168.2.1/") and open the firmware
update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用")
4. After the device reboots automatically, wait until the green power LED
stops blinking and stays solid
5. When the green power LED is solid, hold the reset button until the red
LED starts blinking to clear remaining stock firmware settings
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
- Wi-Fi BDF is shared with WRC-X3000GS2 (ipq-wifi-elecom_wrc-x3000gs2)
as the hardware (SoC, QCN6122, antennas) is identical between the two
models.
- GST2 stock firmware keeps its configuration even when sysupgrade is
called with -n. When installing from the OEM WebUI, those stock
settings can be restored into OpenWrt overlay, so settings must be
initialized after the first OpenWrt boot.
MAC Addresses:
LAN : 38:97:A4:xx:xx:40 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:43 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:41 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:42 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: Taiga Ogawa <zectaiga@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23471
Signed-off-by: Robert Marko <robimarko@gmail.com>
Turris Mox stores the U-Boot environment in SPI NOR flash. Add the
fw_env.config entry pointing to MTD partition 2 at offset 0x0 with
64 KiB env size and sector size, so userspace tools fw_printenv and
fw_setenv work correctly on this board.
Signed-off-by: Štěpán Dalecký <daleckystepan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23421
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for netis EAP930 V1 ceiling access point.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3 (ESMT M15T2G16128A-EFB)
- Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB-104)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x1 (SoC internal phy)
- USB : No
- Buttons : Reset
- LEDs : 1x Status (red), gpio-controlled
1x Status (blue), gpio-controlled
- Power : 48 VDC (PoE) or 12 VDC, 1.5 A
Installation
------------
1. Connect to the access point using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/bl31-uboot.fip FIP
mtd write /tmp/preloader.bin spi0.0
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_eap930-v1-initramfs-recovery.itb' image
on the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM (1 Gbps link is required)
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n squashfs-sysupgrade.itb
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_eap930-v1-initramfs-recovery.itb' image
on the tftp server (IP: 192.168.1.254)
2. Press Reset button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
Return to stock
---------------
1. Upload stock BL2, FIP, ubi partitions backup archives to the /tmp dir
of the router using scp protocol
2. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backups:
zcat /tmp/mtd1_BL2.bin.gz | mtd write - BL2
zcat /tmp/mtd4_FIP.bin.gz | mtd write - FIP
zcat /tmp/mtd5_ubi.bin.gz | mtd write - ubi
3. Reboot the router:
reboot
UART
----
Connection parameters: 115200, 8N1, 3.3V
UART pins are silkscreened on the PCB.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 88:xx:xx:88:xx:d3 | label |
| WLAN 2g | 88:xx:xx:18:xx:d4 | |
| WLAN 5g | 88:xx:xx:78:xx:d4 | |
+---------+-------------------+-----------+
The LAN MAC (hex) was found in 'Factory', 0x1fef20
The WLAN 2g/5g MAC prototype (hex) was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23133
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
U-Boot v2026.01 introduced drivers/mtd/nand/spi/otp.c which adds `spinand_user_otp_size()` and
`spinand_fact_otp_size()`. These functions are called unconditionally from `spinand_init()` in
drivers/mtd/nand/spi/core.c to determine whether to set up OTP methods:
if (spinand_user_otp_size(spinand) || spinand_fact_otp_size(spinand)) {
ret = spinand_set_mtd_otp_ops(spinand); /* drivers/mtd/nand/spi/core.c:2369 */
...
}
Both OTP size functions pass `&spinand->user_otp->layout` or `&spinand->fact_otp->layout` to
`spinand_otp_size()` without first checking whether the pointer is NULL. In the standard probing
path, these pointers are assigned by `spinand_match_and_init()` from the per-chip `spinand_info`
table. `100-21-mtd-spi-nand-add-CASN-page-support.patch` adds CASN detection to `spinand_detect()`
so that when a CASN page is found, `spinand_init_via_casn()` is called instead of
`spinand_id_detect()`. As `spinand_match_and_init()` is only called via `spinand_id_detect()`, it
is never invoked for CASN-probed devices.
As a result, `spinand->user_otp` and `spinand->fact_otp` remain NULL from the zero-initialised DM
priv allocation. Both `spinand_user_otp_size()` and `spinand_fact_otp_size()` spuriously return
non-zero by reading `layout->npages` from a small mapped address computed from their respective
NULL pointer, causing `spinand_init()` to call `spinand_set_mtd_otp_ops()` which reads
`spinand->user_otp->ops` and thereby silently assigns a garbage value to `user_ops` that is then
dereferenced at `if (user_ops->info)`.
int spinand_set_mtd_otp_ops(struct spinand_device *spinand)
{
struct mtd_info *mtd = spinand_to_mtd(spinand);
const struct spinand_fact_otp_ops *fact_ops = spinand->fact_otp->ops;
const struct spinand_user_otp_ops *user_ops = spinand->user_otp->ops;
...
if (user_ops) {
if (user_ops->info) /* drivers/mtd/nand/spi/otp.c:343 */
...
...
}
...
}
On COMFAST CF-WR632AX (MT7981, Winbond W25N01GV) this results in a "Synchronous Abort" during boot.
The crash was confirmed via `addr2line` on the U-Boot ELF:
"Synchronous Abort" handler, esr 0x96000004, far 0xeafffffeeafffffe
elr: 0000000041e2ff44 (drivers/mtd/nand/spi/otp.c:343)
lr : 0000000041e2f2f8 (drivers/mtd/nand/spi/core.c:2369)
The same was observed on Acer Predator Connect W6x (MT7986, Winbond W25N02KV):
"Synchronous Abort" handler, esr 0x96000004, far 0xeafffffeeafffffe
elr: 0000000041e2c868 (drivers/mtd/nand/spi/otp.c:343)
lr : 0000000041e2bc1c (drivers/mtd/nand/spi/core.c:2369)
Fix this by adding NULL guards to both OTP size functions so that they return 0 when the pointer is
NULL. With both functions returning 0, the condition in `spinand_init()` evaluates to false and
`spinand_set_mtd_otp_ops()` is never called, skipping setup of OTP methods entirely for CASN-probed
SPI NAND chips.
This change has no effect on SPI NAND chips that do have OTP data but not CASN. For those chips,
`spinand_match_and_init()` sets `spinand->user_otp` and `spinand->fact_otp` to non-NULL values from
the per-chip table, the NULL guard does not activate, and the existing behaviour is unchanged.
Fixes: https://github.com/openwrt/openwrt/issues/23430
Fixes: b94de14baf ("uboot-mediatek: update to v2026.01")
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23447
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Clean up whitespace and fix LED labels.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/23490
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BL2 image for mt7987_rfb-emmc should be emmc, not sdmmc.
Fixes: 6d35eda ("uboot-mediatek: add builds for the MediaTek MT7987 reference board")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/23490
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update the uboot-ath79 package to v2026.04 release for ath79 devices.
Tested on:
- NEC Aterm WG600HP (AR9344)
- NEC Aterm WG1400HP (QCA9558)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22901
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The Globitel BT-R320 patch has incorrect line numbers and corrupted
ASCII control characters.
Fixes: a3105d3f95 ("mediatek: filogic: add support for Globitel BT-R320")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23526
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gpio-button-hotplug skips buttons with button->irq set because it cannot
handle true interrupt-only gpio-keys descriptions. That check also skips
valid GPIO-backed buttons that provide a separate interrupt specifier, such
as the Meraki MX60 reset button.
Try to acquire the GPIO descriptor before deciding that an explicit-IRQ
button is unsupported. Continue to skip true interrupt-only buttons, and
make the IRQ setup and teardown paths ignore skipped entries.
Tested on: Cisco Meraki MX60. Reset button now works.
Fixes: 23845fa10b ("gpio-button-hotplug: do not error on interrupt attached keys")
Assisted-by: Codex:GPT-5.5
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23382
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add support for the AlwayLink M01K43 5G CPE router.
Hardware specifications:
- SoC: MediaTek MT7981B (Filogic 820), dual-core Cortex-A53
- RAM: 256 MiB DDR3 (0x40000000, size 0x10000000)
- Flash: 128 MiB SPI-NAND (UBI, root) + 4 MiB SPI-NOR (bootloader)
- Ethernet: 4x 1 GbE LAN + 1x 2.5 GbE WAN
(MT7531 DSA switch; WAN via RTL8221B 2.5GbE PHY on MAC1)
- WiFi: MT7981 built-in 2x2 802.11ax (2.4 GHz + 5 GHz)
- USB: 1x xHCI (USB 2.0 only; USB 3.0 PHY pins not routed)
- Modem: M.2 B-Key slot wired for USB (tested: Quectel RM551E-GL,
Quectel RM520N-GL via QMI)
- LEDs: 10x GPIO LEDs (status, WAN, LAN, WiFi 2.4/5, signal bars)
- Buttons: WPS, Reset, RFKill
- Power: 12 V DC barrel jack
- UART: 3.3 V TTL header on PCB, 115200 8N1, no flow control
PCB silkscreen: M01K43 v5.0
Manufacturer: Shenzhen AlwayLink Wireless Technology Co., Ltd.
MAC addresses come from the 'ledeinfo' partition (mtd6) at offset 0x18
(label macaddr_ledeinfo_18); the stored value is the LAN MAC.
interface this port vendor firmware
------------------- ----------- --------------------------
eth0 / LAN bridge base + 0 base + 0
eth1 / WAN base + 1 base + 1
wifi 2.4 GHz band@0 base + 2 base (driver-derived)
wifi 5 GHz band@1 base + 3 base + LAA bit (driver)
The vendor's ethernet scheme (LAN = base, WAN = base + 1) is reproduced
exactly. For WiFi the vendor's proprietary mt_wifi driver ignores the
stored per-radio MAC and derives each BSSID from the base by setting the
locally-administered bit, so the radios are not given clean unicast
offsets. Under mainline mt76 + DSA, reusing the base (LAN) MAC on a radio
collides at L2 with the gmac0 conduit, so this port assigns the 2.4 GHz
and 5 GHz radios base + 2 and base + 3 — unique unicast addresses in the
same OUI block.
Installation
------------
Stock firmware defaults (verified on shipping units):
LAN IP: 192.168.100.1
SSH/web: user 'root', password 'admin'
Serial: 3.3 V TTL UART header on PCB, 115200 8N1, no flow control
Image artifacts produced by this device definition:
openwrt-mediatek-filogic-alwaylink_m01k43-squashfs-factory.bin
openwrt-mediatek-filogic-alwaylink_m01k43-squashfs-sysupgrade.bin
Before flashing, back up the per-unit partitions (cannot be
regenerated):
ssh root@192.168.100.1
dd if=/dev/mtd3 of=/tmp/factory.bin bs=1 count=655360
dd if=/dev/mtd6 of=/tmp/ledeinfo.bin bs=1 count=65536
exit
scp root@192.168.100.1:/tmp/factory.bin .
scp root@192.168.100.1:/tmp/ledeinfo.bin .
Method 1 - From an existing OpenWrt install (sysupgrade):
IMG=openwrt-mediatek-filogic-alwaylink_m01k43-squashfs-sysupgrade.bin
scp "$IMG" root@192.168.1.1:/tmp/sysupgrade.bin
ssh root@192.168.1.1 sysupgrade -n /tmp/sysupgrade.bin
Method 2 - U-Boot serial recovery via TFTP (requires 3.3 V USB-UART
adapter):
1. Attach 3.3 V USB-UART (TX, RX, GND) to the PCB header. Open a
terminal at 115200 8N1, no flow control.
2. Configure a TFTP server on the host PC at IP 192.168.2.88.
Place the factory image in the TFTP root, renamed if desired.
3. Power on the router. The BL2/U-Boot banner prints within ~1
second; press any key during the autoboot countdown to enter
the U-Boot menu.
4. From the menu, select 'Upgrade ubi'. U-Boot's default IP is
192.168.2.1 and it expects the TFTP server at 192.168.2.88.
Provide the factory image filename when prompted.
5. Wait for the write to complete; U-Boot reboots into OpenWrt.
Method 3 - From a NAND programmer (brick-recovery path):
1. Clip onto or desolder the SPI-NAND chip and dump the full
128 MiB with a programmer (e.g. RT809H, CH341A with NAND
adapter). Keep the dump as a recovery image.
2. Using the same programmer, write the factory.bin image to
the UBI region of the NAND. The SPI-NOR (BL2/u-boot-env/
Factory/FIP/woem/ledeinfo/nvram) must NOT be erased - those
partitions are per-unit and live on the separate 4 MiB NOR.
3. Reseat the chip and power on. The bootloader on NOR will
load the new kernel and rootfs from UBI.
Signed-off-by: Richard Jones <richard@netsolution.shop>
Link: https://github.com/openwrt/openwrt/pull/22818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
he_phy_cap and he_mac_cap in phy_capabilities are only populated inside
the iftype_data loop. On 6GHz-only radios (e.g. QCN9074/ath11k_pci),
when capability bytes are unavailable they remain null, causing null
dereferences in device_htmode_append():
Reference error: left-hand side expression is null
if (!(he_phy_cap[3] & 0x80))
Initialise both to [] before the loop and guard the consumer side with
?? [] so bitwise checks conservatively disable beamformer/beamformee/twt
features rather than crashing.
Link: https://github.com/openwrt/openwrt/issues/23488
Signed-off-by: dastarothx <darkastalier@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23496
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
4b274055ede3 libubus: fix NULL dereference on OOM in ubus_queue_msg
8b5be570f13e libubus-acl: fix dangling pointers on blob_memdup failure in acl_recv_cb
9105ea2a349a ubusd_acl: fix NULL dereference on OOM in ubusd_acl_alloc_obj
07d7f34ac278 ubusd_acl: handle allocation failures in ubusd_acl_init_client
497321a5ea90 ubusd_acl: fix NULL dereference on OOM in ubusd_acl_init
f66d52ba983f ubusd_event: fix OOM handling in ubusd_send_event_msg
11ea1b3bdbea ubusd_main: fix async-signal-unsafe SIGHUP handler
0c095592ccb7 ubusd_proto: fix resource leaks and ID tree corruption in ubusd_proto_new_client
f61695e6e12a ubusd_proto: fix NULL dereference for user/group in ubusd_handle_add_watch
7ecacfadd9bc ubusd_proto: fix NULL dereference on OOM in ubusd_proto_init_retmsg
3ab9d7759545 lua: fix inverted argument check in ubus_lua_add
43051ca73aec lua: fix unchecked calloc and memory leak in ubus_lua_load_object
4ca0b141e9a7 ubusd_id: use getrandom(2) unconditionally on Linux
7e4356da8abe ubusd_monitor: fix NULL dereference on OOM in ubusd_monitor_message
5849870f2251 libubus-req: fix file descriptor leaks in ubus_process_req_msg
f29767f90af1 libubus: fix file descriptor leaks in ubus_process_msg
b099d050b59d libubus: make ubus_shutdown idempotent
a564b8dcb395 ubusd_main: check strdup return value in mkdir_sockdir
239edcbaaac8 ubusd_id: fix continue in do-while skipping random ID retry
09d2df45bf38 ubusd: fix NULL dereference on OOM in ubus_msg_enqueue
bcc45ca981fd libubus: actually set FD_CLOEXEC on the ubus socket
8188f5ce8564 libubus-io: close recv_fd captured before get_next_msg failure
7a068bac5a9b libubus-io: byte-swap peer in HELLO when storing as local_id
747013f6ea05 libubus-io: reset sock.fd to -1 after close on ubus_reconnect error path
020a64b9b169 ubusd_acl: use size_t for strlen result in ubusd_acl_alloc_obj
f92ffd289dcc ubusd: use size_t for string and blob length variables
795b32bb96b6 ubusd: use fixed-width types for sequence counters
Link: https://github.com/openwrt/openwrt/pull/23487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This module adds support for the Corsair Commander Pro and Corsair
Commander Pro (1000D) fan and temperature monitoring controllers.
Signed-off-by: Dee HY <dongfengweixiao@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/23465
Signed-off-by: Robert Marko <robimarko@gmail.com>
7df188543e26 libfstools: enable f2fs overlay compression formatting
16718b6e3c0f libfstools: mount f2fs overlay with zstd compression
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace exit(1) on every failure path with return null so callers that
iterate over multiple radios can collect results from the radios that
did succeed instead of aborting on the first one that refuses an
off-channel scan.
Route diagnostics to stderr via warn() so stdout stays clean for
callers parsing JSON output, and include the device name in each
message to disambiguate per-radio failures.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1bf2d490484e libfstools: make get_var_from_file() reusable
0b6022439cad mount_root: add kernel parameter to specify the overlay storage name
e600d842ce81 mount_root: add kernel parameter to specify the overlay fileystem type
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The chunk length is not correct.
Fixes: d2fabb974c ("mediatek: add support for Wavlink WL-WNT100X3 ubootmod")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The generated firmware patches for RealTek's PHYs are host architecture
agnostic. Express this with PKGARCH:=all.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that the upstream RealTek PHY driver is patched to support also
the new 5G and 10G PHYs we can start to phase-out the messy downstream
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is required by the realtek PHY driver for:
* rtl8261n.bin (package "rtl8261n-firmware" or "rtl8261n-lp-firmware")
- RTL8251L 5Gbps PHY
- RTL8261BE 10Gbps PHY
- RTL8261N 10Gbps PHY
* rtl8264b.bin (package "rtl8264b-firmware")
- RTL8254B 5Gbps PHY
- RTL8264 10Gbps PHY
- RTL8264B 10Gbps PHY
These PHY chips need a sequence of register writes for initialization.
These are provided as firmware files which are interpreted/applied by a
new register patch engine.
For the moment, the patch instructions in rtl8261-firmware and
rtl8264b-firmware are the same as from the rtl8261n driver. This should
make it possible to first evaluate the patch engine and driver development
for switching over in adjusting the patch instructions.
Signed-off-by: Balázs Triszka <info@balika011.hu>
[sven: rebase, split, fix package version/release, use conf from rtl8261n
driver]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[daniel: define VERSION matching source date for the resulting packages]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6ab9abb56bcb cgi, file: fix crash due to field_len type mismatch with libubox
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/23446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use a user-supplied profile-id when configuring the APN and PDP type.
Fall back to id "1" in case no profile-id is set by the user.
Link: https://github.com/openwrt/openwrt/issues/21617
Suggested-by: S. Hoot <spoot_hoot@protonmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The AddDepends/pse-pd helper appended kmod-pse-pd to DEPENDS without the
'+' prefix, making it a hard dependency rather than an auto-selecting one.
This breaks pulling any PSE controller driver (kmod-pse-pd692x0,
kmod-pse-si3474, kmod-pse-tps23881, kmod-pse-regulator, ...) in via a
device's DEVICE_PACKAGES: the kmod itself is auto-selected, but the
unsatisfied hard dep on kmod-pse-pd silently drops it from .config.
Prefix the kmod-pse-pd entry with '+' so it auto-selects, matching how
the other deps in the same file (kmod-i2c-core, etc.) are expressed. The
helper is the right place to fix this; every PSE controller driver routes
through it.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23449
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 90M to 122.25M.
Flashing instructions:
1. Login into the device and backup all your partitions,
especially `Factory` and 'HW' to be able to come back to stock and use all
Wavlink services.
2. Unlock mtd partitions:
```
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
```
3. Upload new `bl2` and `fip` to the router /tmp and write them:
```
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-bl31-uboot.fip fip
mtd erase ubi
```
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt initramfs has booted, prepare ubi and envs:
```
ubidetach -p /dev/mtd4 && ubiformat /dev/mtd4 -y && ubiattach -p /dev/mtd4 && ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB && ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
8. Perform sysupgrade.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
| Component | Details |
|------------------|-------------------------------------------------|
| **SoC** | MediaTek MT7986A (4× ARM Cortex-A53 @ 2.0 GHz) |
| **RAM** | 512 MB |
| **Flash** | 256 MB NAND |
| **Ethernet** | 5× 10/100/1000 Mbps (1 WAN + 4 LAN) |
| **WLAN 2.4 GHz** | MediaTek MT7976GN — 802.11b/g/n/ax, 4×4 MIMO |
| **WLAN 5 GHz** | MediaTek MT7976AN — 802.11n/ac/ax, 4×4 MIMO |
| **LEDs** | 1× RGB LED (GPIO-controlled) |
| **Button** | 1× Reset |
| **USB** | Yes |
**MAC Addresses:**
| Interface | Source |
|------------|-------------------------------------------------|
| WAN/Label | u-boot-env MTD partition, "mac" (text) |
| LAN | WAN + 1 |
| 2.4 GHz | WAN + 2 |
| 5 GHz | WAN + 3 |
---
**1. Prepare TFTP server**
Set a static IP on the ethernet interface of your computer (e.g. default: ip `192.168.1.2`, gateway `192.168.1.1`).
Download the initramfs image and host it with the TFTP server.
**2. Interrupt boot**
Attach UART and power on the router. When the boot menu appears, select **Failsafe Mode**,
then press `Ctrl-C` to interrupt and enter the U-Boot prompt.
**3. Load and run initramfs image**
```sh
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
tftpboot 0x46000000 openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-initramfs-kernel.bin
fdt addr $(fdtcontroladdr)
fdt rm /signature
bootm
```
**4. Flash sysupgrade image**
Place the sysupgrade image in `/tmp`, then run:
```sh
sysupgrade /tmp/openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-squashfs-sysupgrade.bin
```
Alternatively, use the sysupgrade option in LuCI.
Note:
- The raw MTD u-boot-env partition is only used for MAC address storage, while the active U-Boot environment is stored in the UBI volume.
- These devices ship with secure boot enabled and stock U-Boot only accepts vendor-signed FIT images.
- BL2/FIP cannot be replaced, so the stock signature verification path cannot be disabled directly.
- Setting ipaddr='' forces U-Boot to exit the web failsafe path and continue into autoboot.
- The custom bootcmd loads OpenWrt from the UBI volume and removes the /signature node before bootm, allowing unsigned OpenWrt FIT images to boot.
- Stock U-Boot expects its environment in a UBI volume named u-boot-env, so it is created during initial setup.
Signed-off-by: sh3ikh-faisal <sheikhfaisal713@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In case OpenWrt is used to build a custom distribution, the default
button handling logic may be undesired.
Add config options to disable default standard button handling code
at build-time.
Signed-off-by: David Bauer <mail@david-bauer.net>
In case OpenWrt is used to build a custom distribution, the default
button handling logic may be undesired.
Add config options to disable default standard button handling code
at build-time.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add support for Xiaomi AX5400 (RA74).
Specifications:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to an
external QCA8337 switch (3 LAN Ports 10/100/1000)
* Flash: Gigadevice GD5F1GQ5REYIG (128 MiB)
* LEDs: 1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
* Buttons: 1x Reset (GPIO 38 Active Low)
1x WPS (GPIO 28 Active Low)
* MAC address layout: LAN (eth1): 0:art @ offset 0x0
WAN (eth0): 0:art @ offset 0x6
Flash instructions: (use redmi-ax5400 image for the Redmi AX5400)
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/23374
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add KEY_SETUP and KEY_VENDOR keys. Many Rockchip devices, including all of those in
e13cbab684 ("rockchip: enable SARADC; add buttons hotplug and ADC kmods to default packages")
have one or both of these buttons.
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23396
Signed-off-by: Robert Marko <robimarko@gmail.com>
OSLEC has been dropped upstream since Linux 6.16.
Reflect that by no longer providing the kernel module package
`kmod-echo` which essentially became an empty stub.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- Sync shared U-Boot DTS nodes with the main device DTS
- Remove duplicate strings
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22929
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix instability by reducing RAM speed to 1866 MT/s
in line with Winbond W634GU6RB-11 specs.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22929
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, there is no SBOM generation in imagebuilder when the package
system 'apk' is used. This commit adds this feature back. This already
worked for the package system 'opkg'.
Furthermore, generating the SBOM using perl is not reproducible if the
input data has not changed. A different file is always generated. This is
not the case with Python. For this reason, Python is now used to generate
the SBOM for the imagebuilder.
The script has already been prepared so that it can also process the opkg
package system for generating the SBOM.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
