This allows us to use the full size of nand, which increases ubi size
from 90M to 122.25M.
Flashing instructions:
1. Login into the device and backup all your partitions,
especially `Factory` and 'HW' to be able to come back to stock and use all
Wavlink services.
2. Unlock mtd partitions:
```
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
```
3. Upload new `bl2` and `fip` to the router /tmp and write them:
```
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-bl31-uboot.fip fip
mtd erase ubi
```
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt initramfs has booted, prepare ubi and envs:
```
ubidetach -p /dev/mtd4 && ubiformat /dev/mtd4 -y && ubiattach -p /dev/mtd4 && ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB && ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
8. Perform sysupgrade.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 512MB DDR3
- FLASH: 128MB SPI-NAND ESMT F50L1G41LB
- NETWORK: 1 x1000M WAN, 1 x 1000M LAN
- WIFI: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 1x STATUS (blue)
- USB: 1x USB 3.0 (XHCI)
- FAN: 1x 5V FAN
Installation / Upgrade Procedure
-----------------------------
1.Log in to the web management page.
2.Select the country code and time zone, set the Wi-Fi password, and
click Save.
3.Click "More", navigate to "Developer Options", and enable the SSH
function.
4.Log in to the device via an SSH client (default IP is usually
192.168.20.1).
5.Use scp to upload the OpenWrt
image(openwrt-mediatek-filogic-wavlink_wl-wnt100x3-squashfs-sysupgrade.bin)
to the /tmp directory
6.Perform the flash by running the sysupgrade command (use -n to
overwrite the existing configuration)
7.Wait for the device to reboot automatically. Once finished, access the
OpenWrt web interface (LuCI) at the default IP 192.168.1.1.
MAC Addresses
-----------------------------
2.4GHz: 80:3F:5D:xx:xx:93 (Factory 0x4)
LAN : 80:3F:5D:xx:xx:91 (Factory, 0x3fff4)
WAN : 80:3F:5D:xx:xx:92 (Factory, 0x3fffa)
5GHz : 02:3F:5D:xx:xx:93 (derived from 2.4GHz MAC, LAA))
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for TP-Link Festa F65, an AX3000 ceiling mount WiFi 6 AP.
Hardware
--------
SOC : MediaTek MT7981B 2x A53
RAM : ESMT M15T4G16256A 512MiB
Flash : ESMT F50L1G41LB 128 MiB
ETH : 1x 1GbE
WiFi : MT7976
Buttons : Reset
Leds : Blue status led on top
Power : DC 12V 1.2A / PoE
Installation
------------
1. Disassemble the device
2. Solder UART to pins VGRT right of the ethernet port
3. Connect UART console (3.3V)
4. Press Ctrl+b to stop in u-boot shell
5. Use `mtkload` to boot `openwrt-initramfs-kernel.bin` via tftp
6. Flash `openwrt-squashfs-sysupgrade.bin` via sysupgrade
Revert to OEM firmware
----------------------
1. Hold reset button while plugging in power
2. Configure host ethernet to 192.168.0.1/24
3. Go to http://192.168.0.254
4. Upload OEM firmware
MAC Addresses
-------------
LAN : DC:62:79:xx:xx:28 (printed on label)
2.4GHz: DC:62:79:xx:xx:28
5GHz : DC:62:79:xx:xx:29
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
| Component | Details |
|------------------|-------------------------------------------------|
| **SoC** | MediaTek MT7986A (4× ARM Cortex-A53 @ 2.0 GHz) |
| **RAM** | 512 MB |
| **Flash** | 256 MB NAND |
| **Ethernet** | 5× 10/100/1000 Mbps (1 WAN + 4 LAN) |
| **WLAN 2.4 GHz** | MediaTek MT7976GN — 802.11b/g/n/ax, 4×4 MIMO |
| **WLAN 5 GHz** | MediaTek MT7976AN — 802.11n/ac/ax, 4×4 MIMO |
| **LEDs** | 1× RGB LED (GPIO-controlled) |
| **Button** | 1× Reset |
| **USB** | Yes |
**MAC Addresses:**
| Interface | Source |
|------------|-------------------------------------------------|
| WAN/Label | u-boot-env MTD partition, "mac" (text) |
| LAN | WAN + 1 |
| 2.4 GHz | WAN + 2 |
| 5 GHz | WAN + 3 |
---
**1. Prepare TFTP server**
Set a static IP on the ethernet interface of your computer (e.g. default: ip `192.168.1.2`, gateway `192.168.1.1`).
Download the initramfs image and host it with the TFTP server.
**2. Interrupt boot**
Attach UART and power on the router. When the boot menu appears, select **Failsafe Mode**,
then press `Ctrl-C` to interrupt and enter the U-Boot prompt.
**3. Load and run initramfs image**
```sh
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
tftpboot 0x46000000 openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-initramfs-kernel.bin
fdt addr $(fdtcontroladdr)
fdt rm /signature
bootm
```
**4. Flash sysupgrade image**
Place the sysupgrade image in `/tmp`, then run:
```sh
sysupgrade /tmp/openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-squashfs-sysupgrade.bin
```
Alternatively, use the sysupgrade option in LuCI.
Note:
- The raw MTD u-boot-env partition is only used for MAC address storage, while the active U-Boot environment is stored in the UBI volume.
- These devices ship with secure boot enabled and stock U-Boot only accepts vendor-signed FIT images.
- BL2/FIP cannot be replaced, so the stock signature verification path cannot be disabled directly.
- Setting ipaddr='' forces U-Boot to exit the web failsafe path and continue into autoboot.
- The custom bootcmd loads OpenWrt from the UBI volume and removes the /signature node before bootm, allowing unsigned OpenWrt FIT images to boot.
- Stock U-Boot expects its environment in a UBI volume named u-boot-env, so it is created during initial setup.
Signed-off-by: sh3ikh-faisal <sheikhfaisal713@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The COMFAST CF-XR186 is a WiFi repeater. The original OEM firmware is a
fork of OpenWrt 21.02.
To replace the OEM firmware with OpenWrt, flash the sysupgrade image
through the firmware upgrade option via the OEM firmware's web UI.
The OEM firmware upgrade page does not provide an option to perform a
factory reset, so after the flash completes and the device reboots,
perform a reset by holding in the WPS/Reset button until the WiFi
LED flashes red.
The led-boot, led-failsafe, led-upgrade, and led-running aliases all
point at the red WLAN GPIO LED.
The green and blue WLAN GPIO LEDs are used to indicate activity on the
2.4GHz and 5GHz radios. 01_leds assigns netdev triggers for those LEDs
to phy0-ap0 and phy1-ap0 respectively; if neither AP interface exists
(e.g. station-only repeater setups), both LEDs stay dark even when WiFi
traffic is flowing.
Specifications:
- SoC: MediaTek MT7981B
- RAM: 256MB
- Flash: SPI NAND
- WiFi: 2.4GHz + 5GHz (AX3000, 4x 3dBi antennas)
- Ethernet: 1x 10/100/1000M
- LEDs: power (not controllable), blue Ethernet, blue/green/red WiFi
- Button: WPS/Reset
- Power: 100-240V AC (wall plug)
- UART: 115200 8N1
MAC Addresses:
- LAN : 40:A5:EF:xx:xx:2D (Factory, 0xe000)
- 2.4GHz: 40:A5:EF:xx:xx:2F (Factory, 0x0004)
- 5GHz : 40:A5:EF:xx:xx:30 (Factory, 0x8000)
Signed-off-by: David Berdik <dgberdik@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While implementing standalone PCS support for DSA, it was found that making
the MAC driver passing the available_pcs array is limiting and problematic
for memory handling and allocation. To better handle this, change the logic
and make phylink allocate the struct and make the MAC driver implement a
function in phylink_config .fill_available_pcs to fill the PCS array.
Update the Airoha and Mediatek driver to reflect this new implementation.
Link: https://github.com/openwrt/openwrt/pull/23413
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix instability by reducing RAM speed to 1866 MT/s
in line with Winbond W634GU6RB-11 specs.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22929
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the netis MEX605, which is a variant based on the netis NX30 V2.
1. Update brand naming from Netis to netis to follow the official branding.
2. Rename NX30V2 to NX30 V2 to correctly reflect it as the second version of the NX30.
3. Update variant notation for consistency.
cherry picked from commit c982357
1. Add 'model' to the DTS for netis NX30 V2 and define WiFi LED.
4. Fix typo.
Signed-off-by: Zhiwei Cao <bfdeh@126.com>
Signed-off-by: David Han <h96643864@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22726
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was used for non nvmem-layout ubootenv support. Since that's gone
and it's not even used anyway, remove.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22367
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Although the AN8855 eFuse driver was merged upstream, other
drivers were not. Restore Kconfig dependencies to enable it.
Also remove useless change logs from the patch.
Fixes: 2129465 ("mediatek: fix patches for Linux 6.18")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/23250
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_JUMP_LABEL is no longer meant to be set explicitly in target
kernel configs after 3be02c118f ("kernel: enable static key").
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/23293
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Qihoo 360T7 (UBI layout).
Aims
----
1. +20 MB additional free space for the packages
2. More reliable storage for the factory and fip partitions (in UBI)
Install (from non-UBI OpenWrt)
------------------------------
1. Navigate http://192.168.1.1/ and download mtd backups
2. Upgrade OpenWrt with installer initramfs image (force upgrade, don't
keep settings). Wait until OpenWrt reboots and until installer:
- Prepare new factory partition
- Format new ubi
- Make ubi volumes
- Write new fip and bl2
3. Navigate http://192.168.1.1/ and Upgrade with OpenWrt 'sysupgrade.bin'
image (don't keep settings)
Installer
---------
Based on OpenWrt UBI Installer Image Generator for Linksys E8450 and
Belkin RT3200
Link: https://github.com/dangowrt/owrt-ubi-installer
Ready installer image
Link: https://github.com/csharper2005/owrt-ubi-installer/tree/qihoo/bin
Installer script
Link: https://github.com/csharper2005/owrt-ubi-installer/blob/qihoo/files/
installer/install.sh
Committing to the parent Daniel's repository is not yet possible because
there are no official images and imagebuilder for Qihoo 360T7 (UBI) yet.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22797
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mt7981b-mercusys-mr85x.dts has redundant executable bit (755 instead
of 644). Fix it.
Fixes: b2648d8 ("mediatek: add support for Mercusys MR85X")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22797
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WRC-X6000GSD is a 4804Mbps 4xMIMO 2.4/5 GHz 11ax (Wi-Fi 6) router
with 2.5Gbps WAN (stock: 1Gbps max.), based on MT7986B
Specification:
- SoC : MediaTek MT7986BLA
- RAM : DDR3 512 MiB (SoC)
- Flash : Winbond 128MiB SPI NAND (W25N01GVZEIG)
- WLAN : 2.4/5 GHz 4T4R (MediaTek MT7986)
- Ethernet : 5x 10/100/1000(/2500) Mbps
- wan : Maxlinear Ethernet GPY211C (max. 2500M)
- lan : MediaTek MT7531 (max. 1000M)
- LEDs/Keys (GPIO): 11x/4x
- UART : through-hole on PCB (J1)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 2 A
Flash layout:
dev: offset size name
mtd0: 0x00000000 0x00100000 "BL2"
mtd1: 0x00100000 0x00080000 "Ubootenv"
mtd2: 0x00180000 0x00200000 "Factory"
mtd3: 0x00380000 0x00200000 "FIP"
mtd4: 0x00580000 0x00020000 "Fwheader"
mtd5: 0x005a0000 0x03200000 "ubi"
mtd6: 0x037a0000 0x00380000 "Config"
mtd7: 0x03b20000 0x00020000 "Fwheader_2"
mtd8: 0x03b40000 0x03200000 "ubi_2"
mtd9: 0x06d40000 0x00380000 "Config_2"
mtd10: 0x070c0000 0x00100000 "persist"
mtd11: 0x071c0000 0x00040000 "Mrd"
mtd12: 0x07200000 0x00380000 "Backup"
Flash instruction using factory.bin image:
1. Boot WRC-X6000GSD in router mode normally
2. Access to the WebUI ("http://192.168.2.1/") on the device
-> その他設定 (Other settings)
-> フォームウェア更新 (Update firmware)
-> ローカルファイル指定 (Specify local file)
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of firmware partition
mstc_rw_bootnum
3. Set the bootnum to opposite value between 1 and 2
mstc_rw_bootnum value
example:
- step2 returned "1": mstc_rw_bootnum 2
- step2 returned "2": mstc_rw_bootnum 1
4. Reboot, to stock FW
5. Flash the stock FW to fuly revert back to original.
Notes:
- With the stock firmware, it will flash to another partition and
toggle boot to that partition when any firmware is flashed.
For example when booting on ubi, the new firmware will be flashed
to ubi_2 and the router will boot from ubi_2 afterwards.
The 5th byte of the Persist partition is the boot value (0x01 or 0x02).
- bootmenu_delay=0 is set from factory so uboot menu is hidden by
default.
- The hardware of WRC-X6000GSD is almost identical to WRC-X6000QS, but
WAN (labeled as "INTERNET") port is limited to 1000 Mbps on stock FW.
On OpenWrt FW, 2500 Mbps connection is available on that port.
MAC Addresses:
LAN : 38:97:A4:xx:xx:58 (Factory, 0x2A(hex)/Ubootenv, "ethaddr"(text))
WAN : 38:97:A4:xx:xx:5B (Factory, 0x24(hex))
2.4GHz: 38:97:A4:xx:xx:59 (Factory, 0x4(hex))
5GHz : 38:97:A4:xx:xx:5A (Factory, 0xA(hex)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WRC-X6000QS is a 4804Mbps 4xMIMO 2.4/5 GHz 11ax (Wi-Fi 6) router
with 2.5Gbps WAN, based on MT7986b
Specification:
- SoC : MediaTek MT7986B
- RAM : DDR3 512 MiB
- Flash : Winbond 128MiB SPI NAND
- WLAN : 2.4/5 GHz 4T4R (MediaTek MT7986)
- Ethernet : 5x 10/100/1000 Mbps
- wan : Maxlinear Ethernet GPY211C
- lan : MediaTek MT7531
- LEDs/Keys (GPIO): 11x/4x
- UART : through-hole on PCB (J1)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 2 A
Flash layout:
dev: offset size name
mtd0: 0x00000000 0x00100000 "BL2"
mtd1: 0x00100000 0x00080000 "Ubootenv"
mtd2: 0x00180000 0x00200000 "Factory"
mtd3: 0x00380000 0x00200000 "FIP"
mtd4: 0x00580000 0x00020000 "Fwheader"
mtd5: 0x005a0000 0x03200000 "ubi"
mtd6: 0x037a0000 0x00380000 "Config"
mtd7: 0x03b20000 0x00020000 "Fwheader_2"
mtd8: 0x03b40000 0x03200000 "ubi_2"
mtd9: 0x06d40000 0x00380000 "Config_2"
mtd10: 0x070c0000 0x00100000 "persist"
mtd11: 0x071c0000 0x00040000 "Mrd"
mtd12: 0x07200000 0x00380000 "Backup"
UBI layout:
name: size:
kernel 0x00364000 dynamic
rootfs 0x00FFC000 dynamic
rootfs_data 0x01A47000 dynamic
Flash instruction using factory.bin image:
1. Boot WRC-X6000QS in router mode normally
2. Access to the WebUI ("http://192.168.2.1/") on the device
-> その他設定 (Other settings)
-> フォームウェア更新 (Update firmware)
-> ローカルファイル指定 (Specify local file)
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of firmware partition
mstc_rw_bootnum
3. Set the bootnum to opposite value between 1 and 2
mstc_rw_bootnum value
example:
- step2 returned "1": mstc_rw_bootnum 2
- step2 returned "2": mstc_rw_bootnum 1
4. Reboot, to stock FW
5. Flash the stock FW to fuly revert back to original.
Note 1: With the stock firmware, it will flash to another partition and
toggle boot to that partition when any firmware is flashed.
For example when booting on ubi, the new firmware will be flashed
to ubi_2 and the router will boot from ubi_2 afterwards.
The 5th byte of the Persist partition is the boot value (0x01 or 0x02).
During my tests, it never switched to another boot partition if the
firmware failed boot. So if openwrt doesn't boot,
UART might be required to recover.
Note 2: bootmenu_delay=0 is set from factory so uboot menu is hidden.
[original work]
Signed-off-by: Yuhei Amemiya <minihui@me.com>
[fixes, improvements]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device support for zbt-z8103ax-d
Model D DTS is identical to Model C zbt-z8103ax-c.
Both models share same motherboard.
Difference between models is
- Model C is a cylinder shape enclosure
containing internal antennas.
- Model D is a sandwich shape enclosure
with 6 external antennas.
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: Winbond SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit) MediaTek MT7531
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7981B 2.4Ghz & 5.8Ghz
Led Layout from left to right:
Power
Mesh (RGB Led, user controllable, default set to OpenWrt Status)
WLAN 2.4G (user controllable)
WAN (user controllable)
LAN3
LAN2
LAN1
WLAN 5G (user controllable)
Installation:
A. Through U-Boot menu:
- Prepare your connecting computer to use static IP
(legacy notation) 192.168.1.10 netmask 255.255.255.0
(CIDR notation) 192.168.1.10/24
- Power down the router and hold in the Reset button.
- While holding in the button power up the router again.
- Hold the button in for 10 seconds and then release.
- Use your browser to go to 192.168.1.1
- If you see a GUI allowing for flashing firmware you are at the right spot.
- Upload the **Factory** image file.
Note: U-Boot GUI it can be used to recover from an incorrect firmware flash.
B. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1)
and then navigate to
System -> Backup/Flash firmware, then flash the firmware
MAC Addresses:
MAC Addresses were found in Factory partition:
offset 0x4 F8:5E:3C:xx:xx:aa --> Router Label -2
offset 0xa F8:5E:3C:xx:xx:bb --> Router Label -1
offset 0x24 F8:5E:3C:xx:xx:cc --> Router Label +1
offset 0x2a F8:5E:3C:xx:xx:yy --> printed on Router Label
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Link: https://github.com/openwrt/openwrt/pull/21626
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nand has a valid mediatek nand badblock management (NMBM) signature.
Gets used for non-UBI partions BL2, u-boot-env, Factory and FIT.
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Link: https://github.com/openwrt/openwrt/pull/21626
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches to improve support for using 3rd-party DSA switches
like MaxLinear MxL862xx with MediaTek's mtk_eth_soc being the
conduit. This involves reorganizing hardware queues to avoid
overlap (currently dp->index is used -- if there is more than one
DSA switch this is problematic), and correctly programming flows
of the non-MTK DSA users ports in the PPE offloading engine.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the upstream properties to describe the USXGMII PCS polarity as
the downstream mediatek,pnswap{,-rx,tx} was dropped.
This board was the only user.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
LINK_INBAND_ENABLE isn't valid for 5GBase-R/10GBase-R modes which
by definition don't support any in-band an. Correctly report
LINK_INBAND_DISABLE to fix 10G fiber SFP modules no longer working.
While at it also get rid of downstream pn-swap properties in favor
of using the upstream schema.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Device support for zbt-z8106ax-s
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: Winbond SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit) MediaTek MT7531
Buttons: Reset
Power: DC 12V 1A
WiFi: MT7981B 2.4Ghz & 5Ghz
USB 3
M2 slot to hold LTE modem
1 nano SIM slot (user controllable)
Hardware watchdog (confirmed to work)
Router comes in a plastic tower with all antennas internal.
- 4 antennas for LTE 4G/5G communication
- 2 antennas for Wifi 2.4 GHz
- 2 antennas for Wifi 5 GHz
Led Layout:
Power (green, user controllable, default set to OpenWrt Status)
Mobile (green, user controllable)
WLAN 2.4G (green, user controllable)
WLAN 5G (green, user controllable)
WAN (amber, user controllable, set to show eth1)
LAN1 (amber, hardware controlled)
LAN2 (amber, hardware controlled)
LAN3 (amber, hardware controlled)
LAN4 (amber, hardware controlled)
SIM Slot:
Controlled via exported GPIO named SIM.
echo "0" > /sys/class/gpio/sim/value
- turns off sim slot labelled SIM
echo "1" > /sys/class/gpio/sim/value
- turns on sim slot labelled SIM
---
Installation:
A. Through U-Boot menu:
- Prepare your connecting computer to use a static IP in
network 192.168.1.0/24 like
a) 192.168.1.10 netmask 255.255.255.0 (legacy notation)
b) 192.168.1.10/24 (CIDR notation)
- Power down the router and hold in the Reset button.
- While holding in the button power up the router again.
- Hold the button in for 10 seconds and then release.
- Use your browser to go to 192.168.1.1
- If you see a GUI allowing for flashing firmware then you got the right spot.
- Upload the **Factory** image file.
Note: U-Boot GUI it can be used to recover from an incorrect firmware flash.
B. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by vendor),
you can easily upgrade by going to the dashboard (192.168.1.1) and
then navigate to "System" -> "Backup/Flash firmware"
Flash OpenWRT firmware.
Important: Take care to deselect (untick) option
"keep settings". Settings done by vendor are incompatible with
versions 24.10 or 25.12.
MAC Addresses:
MAC Addresses were found in Factory partition:
offset 0x4 F8:5E:3C:xx:xx:aa --> Router Label -2
offset 0xa F8:5E:3C:xx:xx:bb --> Router Label -1
offset 0x24 F8:5E:3C:xx:xx:cc --> Router Label +1
offset 0x2a F8:5E:3C:xx:xx:yy --> printed on Router Label
Hardware Watchdog:
Device features a GPIO controlled hardware watchdog.
Verfied by removing procd controlled watchdog and
seeing device rebooting.
---
Notes:
The zbt-z8106ax-s could be ordered from vendor with a variety of modems.
Mine came with a 4G LTE modem Quectel EC200A.
Quectel firmware was at EC200AEUHAR01A30M16.
Choices for ordering with 5G LTE were available.
Modem communication is set to ethernet control mode (ECM) by vendor.
Package modemmanager works fine with Quectel EC200A.
You may also decide to use FUjR/Qmodem github repository
to have it manage LTE modem.
Please take note that internal switch port named lan5 isn't
wired to LTE modem in model S as opposed to model T.
Just removing lan5 from DTS did cause unwanted reboots whenever
a cable is plugged into LAN ports 1-4. Disabling port lan5
in DTS however works fine. No unwanted reboots due to
plug/unplug cable into any lan or wan port.
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Link: https://github.com/openwrt/openwrt/pull/22912
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Import pending series introducing support for standalone PCS drivers.
This has previously already been used by the airoha target, and is
also the base for the closer-to-upstream patches for MediaTek MT7988
10G SerDes support.
In order to not having to diverge from upstream also backport series
for standardized handling for PHY and PCS SerDes pair polarity.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Pawlik figured out that a stale patch hunk breaks one of the
two 10G SerDes PCS ports of MT7988. Remove the hunk to make 10G
Ethernet work on both SerDes PCS with Linux 6.18.
Testing was done using a Aquantia AQR113C SFP+ module.
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adapt kernel configuration of the mt7629 subtarget for Linux 6.18.
This was only compile-tested as I don't have the hardward.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The by-now-upstream driver for the built-in 2.5GE PHY of the MediaTek
MT7988 and MT7987 SoC loads firmware at probe time.
Build the driver as a module in order to make sure the driver only
attempts to load the firmware by the time the rootfs with the firmware
file has become available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream changes to phylink require to make some small changes to our
downstream Airoha AN8855 DSA driver, so it build with Linux 6.18.
The efuse driver is upstream by now and can be dropped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Delete patches merged upstream and refresh the remaining patches.
Import pending patchset to fix read-out-of-bounds bug in clk driver
while at it, as it makes maintaining the downstream clk driver for
MT7987 easier.
Replace downstream patch for Fidelix FM35X1GA SPI-NAND chip with
upstream commit replacing it (Dosilicon DS35Q1GA is indentical).
Several additional fixes were needed for MT7623N, especially to get
HDMI and the Mali-450 GPU working again...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
BUFFALO WSR-3000AX4P is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7981B.
Specification:
- SoC : MediaTek MT7981B
- RAM : DDR4 512 MiB (ESMT M16U4G16256A-KJBG)
- Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7981B (SoC))
- Ethernet : 4x 10/100/1000 Mbps
- switch : MediaTek MT7531A
- LEDs/Keys (GPIO): 6x/4x
- UART : through-hole on PCB (J1)
- assignment : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1.5 A (Max. 14.4 W)
Flash instruction using initramfs image:
1. Prepare a TFTP server with 192.168.11.2
2. Rename initramfs image to "linux.ubi-recovery" and put it to the TFTP
directory
3. Hold the "AOSS" button and power on WSR-3000AX4P, release after 7~
seconds
4. The bootloader automatically downloads the initramfs image and boots
with it
5. After booting, upload a sysupgrade image to the device and perform
sysupgrade with it
6. Wait ~100 seconds to complete flashing
Reverting to stock image:
1. Download a official firmware and decrypt it by buffalo-enc
example:
buffalo-enc -i <official .bin> -o fw.dec -d -O 0xC8 -l
2. Upload the decrypted image to the device
3. Flash the image to the UBI in "ubi_kernel" partition on the device
example:
. /lib/upgrade/common.sh
. /lib/upgrade/nand.sh
CI_UBIPART="ubi_kernel" nand_do_flash_file fw.dec
4. Reboot the device
reboot
Notes:
- WSR-3000AX4P has 2x OS images ("ubi"/"Kernel2"), but the second one
is only for backup and not used for booting.
image handling on the bootloader:
- "ubi" is broken : "Kernel2" --(copy)--> "ubi"
- "Kernel2" is broken : "ubi" --(copy)--> "Kernel2"
- "ubi" != "Kernel2" :
- boot_select=0: "ubi" --(copy)--> "Kernel2"
- boot_select=1: "Kernel2" --(copy)--> "ubi", set boot_select to '0'
MAC Addresses:
LAN : EC:5A:31:xx:xx:50 (board_data, "mac" (text))
WAN : EC:5A:31:xx:xx:50
2.4GHz: EC:5A:31:xx:xx:52
5GHz : EC:5A:31:xx:xx:59
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22587
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable ascii-env NVMEM driver (CONFIG_NVMEM_LAYOUT_ASCII_ENV) on
mediatek/filogic subtarget, to handle ascii-based MAC addresses
in key-value format stored to the mtd partition.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22587
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device support for zbt-z8106ax-t
Vendor Zbtlink advertizes this device as model Z8106AX-M2-T
on their website www.zbtlink.com. Device label sticked on
enclosure however states this is model Z8106AX version -T.
I made firmware selector to show this device as
- ZBT-Z8106AX-T to match information printed on the label and
- ZBT-Z8106AX-M2-T to match information found on vendors web pages.
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: Winbond SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit) MediaTek MT7531
Buttons: Reset
Power: DC 12V-32V 1A
WiFi: MT7981B 2.4Ghz & 5Ghz
USB 3
M2 slot to hold LTE modem
2x nano SIM slots (user controllable)
Router comes in a flat metal box with all antennas detachable.
- 4 antennas for LTE 4G/5G communication
- 2 antennas for Wifi 2.4 GHz
- 2 antennas for Wifi 5 GHz
Power supply could be between 12V and 32V.
This serves both cars equipped with 12V batteries
and trucks equipped with 24V batteries.
Led Layout:
Power (green, user controllable, default set to OpenWrt Status)
Mobile (green, user controllable)
WLAN 2.4G (green, user controllable)
WLAN 5G (green, user controllable)
WAN (amber, user controllable, set to show eth1)
LAN1 (amber, hardware controlled)
LAN2 (amber, hardware controlled)
LAN3 (amber, hardware controlled)
LAN4 (amber, hardware controlled)
SIM Slots:
Controlled via exported GPIO named SIM.
echo "0" > /sys/class/gpio/sim/value
- selects upper sim slot labelled SIM1
echo "1" > /sys/class/gpio/sim/value
- selects lower sim slot labelled SIM2
Slot SIM2 is set as default and matches label on Router enclosure
---
Installation:
A. Through U-Boot menu:
- Prepare your connecting computer to use a static IP in
network 192.168.1.0/24 like
a) 192.168.1.10 netmask 255.255.255.0 (legacy notation)
b) 192.168.1.10/24 (CIDR notation)
- Power down the router and hold in the Reset button.
- While holding in the button power up the router again.
- Hold the button in for 10 seconds and then release.
- Use your browser to go to 192.168.1.1
- If you see a GUI allowing for flashing firmware then you got the right spot.
- Upload the **Factory** image file.
Note: U-Boot GUI it can be used to recover from an incorrect firmware flash.
B. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by vendor),
you can easily upgrade by going to the dashboard (192.168.1.1) and
then navigate to "System" -> "Backup/Flash firmware"
Flash OpenWRT firmware and take care to deselect (untick) option
"keep settings". Settings done by vendor are incompatible with
versions 24.10 or 25.12.
MAC Addresses:
MAC Addresses were found in Factory partition:
offset 0x4 F8:5E:3C:xx:xx:aa --> Router Label -2
offset 0xa F8:5E:3C:xx:xx:bb --> Router Label -1
offset 0x24 F8:5E:3C:xx:xx:cc --> Router Label +1
offset 0x2a F8:5E:3C:xx:xx:yy --> printed on Router Label
Hardware Watchdog:
Device features a GPIO controlled hardware watchdog.
Verfied by removing procd controlled watchdog and
seeing device rebooting.
---
Notes:
The zbt-z8106ax-t could be ordered from vendor with a variety of modems.
Mine came with a Quectel RM520N-GL. Quectel firmware was at RM520NGLAAR01A07M4G.
This level of firmware made some trouble connecting with some of my
SIM cardproviders.
Newer firmware level RM520NGLAAR01A08M4G_01.205.01.205 was available searching
github repositories. Upgrading my RM520-GL allowed to get successful connects
that did fail with older Quectel firmware.
Modem communication is set to ethernet control mode (ECM) by vendor.
Vendor takes advantage of ECM by wiring modem to internal switch port WWAN.
OpenWRT network configuration wants to define two network interfaces
- Network interface covering USB0 set with high metric
- Network interface covering WWAN set with low metric
Network interface covering WWAN would be preferred default route.
Please take note that internal switch port wired to LTE modem is named LAN5
in vendor provided firmwares. OpenWRT however names port as WWAN to better
describe purpose of port. WWAN is suggested to be assigned to firewall zone WAN.
Did use package qmodem from github repository FUjR/QModem to manage RM520N-GL LTE modem.
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Link: https://github.com/openwrt/openwrt/pull/21834
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing patch description, so all patches of the mediatek target can
be applied to a kernel tree using 'git am'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a long standing bug in the mediatek-cci-devfreq driver which leads
to the driver switching off the CPU power regulator in case of another
resource not being ready in time -- a classic probe-order race condition.
As a work-around it would of course just as well be possible to set the
CPU regulator as 'regulator-always-on' (and not just 'regulator-boot-on'),
but practically all MT7988 devices have copy&pasted the PMIC device tree
hunk which sets only 'regulator-boot-on').
Hence, in order not having to fix all device trees, a proper fix in the
driver is preferred.
Fixes: #683
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
